Age | Commit message (Collapse) | Author |
|
[why]
During hotplug, a DP port may be connected to the sink through
passive adapter which does not support DPCD reads. Issuing reads
without checking for this condition will result in errors
[how]
Ensure the link is in aux_mode before initiating operation that result
in a DPCD read.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Wait counter is not being reset for each pipe.
[How]
Move counter reset into pipe loop scope.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY & HOW]
There is a problem in hscale_pixel_rate, the bug
causes DCN to be more optimistic (more likely to underflow)
in upscale cases during prefetch.
This commit ports the fix from DV code to address these issues.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The dcn20_validate_bandwidth function would have code touching the
incorrect registers emitted outside of the boundaries of the
DC_FP_START/END macros, at least on ppc64le. Work around the
problem by wrapping the whole function instead.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.6.x
|
|
Once should generally be enough for diagnosing what lead up to it,
repeating it over and over can be pretty annoying.
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Current locking scheme for cursor can result in a flip missing
its vsync, deferring it for one or more vsyncs. Result is a
potential for stuttering when cursor is moved.
[How]
Use cursor update lock so that flips are not blocked while cursor
is being programmed.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
The downspread percentage was copied over from a previous version
of the display_mode_lib spreadsheet. This value has been updated,
and the previous value is too high to allow for such modes as
4K120hz. The new value is sufficient for such modes.
[HOW]
Update the value in dcn21_resource to match the spreadsheet.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Fixes the following scenario:
- Flip has been prepared sometime during the frame, update pending
- Cursor update happens right when VUPDATE would happen
- OPTC lock acquired, VUPDATE is blocked until next frame
- Flip is delayed potentially infinitely
With the igt@kms_cursor_legacy cursor-vs-flip-legacy test we can
observe nearly *13* frames of delay for some flips on Navi.
[How]
Apply the Raven workaround generically. When close enough to VUPDATE
block cursor updates from occurring from the dc_stream_set_cursor_*
helpers.
This could perhaps be a little smarter by checking if there were
pending updates or flips earlier in the frame on the HUBP side before
applying the delay, but this should be fine for now.
This fixes the kms_cursor_legacy test.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Currently RN SOC bounding box update assumes we will get at least
2 clock states from SMU. This isn't always true and because of special
casing on first clock state we end up with low disp, dpp, dsc and phy
clocks.
This change removes the special casing allowing the first state to
acquire correct clocks.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Check before programming the register since it isn't present on
all IPs using this code.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
We have seen a green screen after resume from suspend in a Raven system
connected with two displays (HDMI and DP) on X based system. We noticed
that this issue is related to bad DCC metadata from user space which may
generate hangs and consequently an underflow on HUBP. After taking a
deep look at the code path we realized that after resume we try to
restore the commit with the DCC enabled framebuffer but the framebuffer
is no longer valid.
[how]
This problem was only reported on Raven based system and after suspend,
for this reason, this commit adds a new parameter on
fill_plane_dcc_attributes() to give the option of disabling DCC
programmatically. In summary, for disabling DCC we first verify if is a
Raven system and if it is in suspend; if both conditions are true we
disable DCC temporarily, otherwise, it is enabled.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1099
Co-developed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
When link loss happened, monitor can not light up if only re-train the
link.
[How]
Blank all the DP streams on this link before re-train the link, and then
unblank the stream
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Organizational Unit Identifier register is optional, and its
presence is published via Down Stream Port Count register.
Writing this register when not available will result in errors
[how]
Read this register and continue writing OUI only if the panel
has the support advertised.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Mirror what we do for i2c display buses.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We were registering the aux device in the MST late_register
rather than the regular one.
v2: handle eDP as well
Fixes: 405a1f9090d1ac ("drm/amdgpu/display: split dp connector registration (v4)")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1100
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
|
|
fixes unused variable warning.
Reported-by: Eric Biggers <ebiggers@kernel.org>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
In cases where a clock table is malformed such that fclk entries have
frequencies but not voltages listed, we don't catch the error and set
clocks to 0 instead of using hardcoded values as we should.
[HOW]
Add check for clock tables fclk entry's voltage as well
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
If dc->clk_mgr->funcs->are_clock_states_equal is set, then
wm_optimized_required is never checked. In that case, when going from a
higher mode to a lower mode, wm_optimized_required remains true until
the next mode change.
[How]
- move from else-if to unconditional or
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In some usecases, like tiled display, the stream and plane configuration
can be setup in a way where the caller expects DAL to perform the
clipping, eg:
P0:
src_rect(0, 0, w, h)
dst_rect(0, 0, w, h)
P1:
src_rect(w, 0, w, h)
dst_rect(0, 0, w, h)
Cursor is enabled on both streams with the same position.
This can result in double cursor on tiled display, even though this
behavior is technically correct from the DC interface point of view.
We need a mechanism to control this dynamically.
[How]
This is something that should live in the DM layer based on detection
of the specified configuration but it's not something that we really
have enough information to deal with today.
Add a flag to the cursor position state that specifies whether we
want DC to do the translation or not and make it opt-in and let
the DM decide when to do it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If a plane isn't being actively enabled or disabled then DC won't
always recalculate scaling rects and ratios for the primary plane.
This results in only a partial or corrupted rect being displayed on
the screen instead of scaling to fit the screen.
[How]
Add back the logic to recalculate the scaling rects into
dc_commit_updates_for_stream since this is the expected place to
do it in DC.
This was previously removed a few years ago to fix an underscan issue
but underscan is still functional now with this change - and it should
be, since this is only updating to the latest plane state getting passed
in.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
For medium updates that change nothing but the source rect position
the viewport doesn't change on DCN20.
We're missing the check for the position update bit that was there in
the DCN10 hardware sequencer.
[How]
Check the position bit along with the scaling bit like we were doing
with DCN20.
We shouldn't actually hit a case where context != current_state in
our programming/commit model but guard against it anyway since it was
guarded for the other bits.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Cursor pos is correctly adjusted from DC side for source rect offset
on DCN ASIC, but only on the overlay.
This is because DM places offsets the cursor for primary planes only
to workaround missing code in DCE for the adjustment we're now correctly
doing in DC for DCN ASIC.
[How]
Drop the adjustment for source rect from the DM side of things and put
the code where it actually belongs - in DC on the pipe level.
This matches what we do for DCN now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Changing policy to dynamic will allow 4k multi display configs
to be supported at DPM0
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Cursor is drawn as part of the framebuffer for a plane on AMD hardware.
The cursor position on the framebuffer does not change even if the
source rect viewport for the cursor does. This causes the cursor to be
clipped.
The following IGT tests fail as a result of this issue:
- kms_plane_cursor@pipe-*-viewport-size-*
[How]
Offset cursor position by plane source rect viewport. If the viewport
is unscaled then the cursor is now correctly positioned on any
plane - primary or overlay.
There is still a hardware limitation for dealing with the cursor size
being incorrectly scaled but that's not something we can address.
Add some documentation explaining some of this in the code while we're
at it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
After v_total_min and max are updated in vrr structure, the changes are
not reflected in stream adjust. When these values are read from stream
adjust it does not reflect the actual state of the system.
[How]
Set stream adjust values equal to vrr adjust values after vrr adjust
values are updated.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Prop are created at boot stage, and not allowed to create new prop
after device registration.
[How]
Reuse the connector property from SST if exist.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes build error of:
"use of undeclared identifier 'RENOIR_A0'"
To fix the same, this patch re-orders the
ASIC declarations accordingly.
Fixes: 41ef3dcd86443fa ("drm/amd/display: Fix RV2 Variant Detection")
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Some displays have an issue where the hdcp chips are initialized after the
display has already lit up. This means we can sometimes authentication too early
and cause authentication failures.
This happens when HDCP is enabled and the display is power cycled. Normally we
will authenticate 2 seconds after the display is lit, but some displays need a
bit more time.
[How]
Increase delay to 3 second before we start authentication.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
-We need to cancel future callbacks/watchdogs events when a callback/watchdog event happens
[How]
-fix typo in event_callback()
-cancel callback, not watchdog
-cancel watchdog events in event_watchdog_timer().
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When content type property is set to 1. We should enable hdcp2.2 and if we cant
then stop. Currently the way it works in DC is that if we fail hdcp2, we will
try hdcp1 after.
[How]
Use link config to force disable hdcp1.4 when type1 is set.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DML expects num_states to exclude the duplicate state.
[How]
Set num_states to correct value to prevent array off-by-one error. Also
refactor max clock level code for diags.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
BT2020 is not supported in COLOR_ENCODING property of planes. Only
BT601 and BT709 was available.
[How]
Allow BT2020 as legit value in setting COLOR_ENCODING property.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Nominal pixel clock and EDID information differ in precision so although
monitor reports maximum refresh is 2x minimum, LFC was not being
enabled.
[How]
Use minimum refresh rate as nominal/2 when EDID dictates that min
refresh = max refresh/2.
v2: squash in 64 bit divide fix
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
CTM was only supported at CRTC level and we need color space conversion
in linear space at plane level.
[How]
- Add plane-level CTM to dc interface
- Program plane-level CTM in DCN
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Change is causing a regression where the OPC app no longer functions
properly.
[How]
Revert the changelist causing the issue.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In some scenario like 1366x768 VSR enabled connected with a 4K monitor
and playing 4K video in clone mode, underflow will be observed due to
decrease dppclk when previouse surface scan isn't finished
[How]
In this use case, surface flip is switching between 4K and 1366x768,
1366x768 needs smaller dppclk, and when decrease the clk and previous
surface scan is for 4K and scan isn't done, underflow will happen. Not
doing optimize bandwidth in case of flip pending.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
For some monitors extreme flickering can occur while using LFC for if
we're not doing the DRR timing update for V_TOTAL_MIN / V_TOTAL_MAX at
the DP start of frame.
Hardware can default to any time in the frame which isn't the behavior
we want.
[How]
Add a new function for setting the double buffering mode for DRR timing.
Default to DP start of frame double buffering on timing generator init.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
P010 pixel format is not declared as supported in DRM and DM.
[How]
Add P010 format to the support list presented to DRM and checked in DM
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Diagnostics scaling test failing to set required number of vertical taps
in 4:2:0 surface case
[How]
In dpp3_get_optimal_number_of_taps() need to use LB_MEMORY_CONFIG_3 for
4:2:0 surface case. In resource_build_scaling_params() make sure to also
set plane res alpha enable based on updated surface state
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Commit '16f17eda8bad ("drm/amd/display: Send vblank and user
events at vsartup for DCN")' introduces a new way of pageflip
completion handling for DCN, and some trouble.
The current implementation introduces a race condition, which
can cause pageflip completion events to be sent out one vblank
too early, thereby confusing userspace and causing flicker:
prepare_flip_isr():
1. Pageflip programming takes the ddev->event_lock.
2. Sets acrtc->pflip_status == AMDGPU_FLIP_SUBMITTED
3. Releases ddev->event_lock.
--> Deadline for surface address regs double-buffering passes on
target pipe.
4. dc_commit_updates_for_stream() MMIO programs the new pageflip
into hw, but too late for current vblank.
=> pflip_status == AMDGPU_FLIP_SUBMITTED, but flip won't complete
in current vblank due to missing the double-buffering deadline
by a tiny bit.
5. VSTARTUP trigger point in vblank is reached, VSTARTUP irq fires,
dm_dcn_crtc_high_irq() gets called.
6. Detects pflip_status == AMDGPU_FLIP_SUBMITTED and assumes the
pageflip has been completed/will complete in this vblank and
sends out pageflip completion event to userspace and resets
pflip_status = AMDGPU_FLIP_NONE.
=> Flip completion event sent out one vblank too early.
This behaviour has been observed during my testing with measurement
hardware a couple of time.
The commit message says that the extra flip event code was added to
dm_dcn_crtc_high_irq() to prevent missing to send out pageflip events
in case the pflip irq doesn't fire, because the "DCH HUBP" component
is clock gated and doesn't fire pflip irqs in that state. Also that
this clock gating may happen if no planes are active. This suggests
that the problem addressed by that commit can't happen if planes
are active.
The proposed solution is therefore to only execute the extra pflip
completion code iff the count of active planes is zero and otherwise
leave pflip completion handling to the pflip irq handler, for a
more race-free experience.
Note that i don't know if this fixes the problem the original commit
tried to address, as i don't know what the test scenario was. It
does fix the observed too early pageflip events though and points
out the problem introduced.
Fixes: 16f17eda8bad ("drm/amd/display: Send vblank and user events at vsartup for DCN")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-next
amd-drm-next-5.7-2020-03-19:
amdgpu:
- SR-IOV fixes
- RAS fixes
- Fallthrough cleanups
- Kconfig fix for ACP
- Fix load balancing with VCN
- DC fixes
- GPU reset fixes
- Various cleanups
scheduler:
- Revert job distribution optimization
- Add a helper to pick the least loaded scheduler
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200319175418.4237-1-alexander.deucher@amd.com
|
|
Adds logic that will determine if pipes need merging during validation.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The scratch space can be used to pass data between x86 and DMCUB. DMCUB
will manage the actually mapping of CW7 internally, driver does not
program the window.
[How]
Allocate extra space within the DMUB service's framebuffer for this
scratch space and expose them from the service for use in DC.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
before update dpp DTO, we check dppclks in context to determine it is
changed or not, but dppclks in context will be updated anyways after
flip is done, so compare dppclks in context will always get an equal
result.
[How]
Add pipe dpp clks in dccg and compare values between dccg and context.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Causes regression with MST DSC displays not lighting up after DPMS
[how]
Revert commit 8cc426d79be1c3 ("drm/amd/display: Program DSC during timing programming")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
underflow happened when playing video on 1366x768 + 4K clone mode due to
incorrect handle watermark change flag and lower down clocks to early.
[How]
Check watermark change flag when decide doing optimized, and check
optimized required flag to do clock update.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
this register not exist in some asic, based on request remove this from
dc.
[how]
add guard for sanization.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
and SST
[Why]
We should check MST BU support capability on output port before building
vsc info packet.
[How]
Add a new definition for port and sink capability check.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
In headless boot cases, self refresh control registers are not
programmed on boot. In certain hybrid graphics cases this may cause
cstate entering to get blocked causing a hang.
[HOW]
Program self refresh control register on boot.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
DP doesn't have message id as the first byte of an hdcp message,
current hdcp psp unifies HDMI and DP message so that it is required
when reading DP HDCP messages in hdcp_ddc, a message id needs to be
added as the first byte of the HDCP message.
The id is currently assigned as a magic number which is not a good
coding practice.
[how]
Replace magic numbers with macro defined in hdcp headers.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|