| Age | Commit message (Collapse) | Author |
|---|
|
Fix the check on the number of IRQs to allow up to the maximum (32)
instead of only the maximum minus one.
Fixes: 96868dce644d ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Link: https://lore.kernel.org/r/20201107081420.60325-10-damien.lemoal@wdc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio fixes for v5.10-rc3
- fix missing conversion to gpiolib irqchip in gpio-dwapb
- fix bank properties for ast2600 variant in gpio-aspeed
- make sysfs work again when the character device is disabled
- fix interrupt handling in gpio-pcie-idio-24
|
|
This enables the PEX8311 internal PCI wire interrupt and the PEX8311
local interrupt input so the local interrupts are forwarded to the PCI.
Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This fixes the COS Enable Register value for enabling/disabling the
corresponding IRQs bank.
Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Fix the bitwise operation to remove only the corresponding bit from the
mask.
Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
In gpiochip_setup_dev() the call to gpiolib_cdev_register() indirectly
calls device_add(). This is still required for the sysfs even when
CONFIG_GPIO_CDEV is not selected in the build.
Replace the stubbed functions in gpiolib-cdev.h with macros in gpiolib.c
that perform the required device_add() and device_del() when
CONFIG_GPIO_CDEV is not selected.
Fixes: d143493c01b7 (gpiolib: make cdev a build option)
Reported-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This reverts commit 579ced8fdb00b8e94304a83e3cc419f6f8eab08e.
Turns out I was overly optimistic about cpu_pm blocking idle being a
solution for handling edge interrupts. While it helps in preventing
entering idle states that potentially lose context, we can still get
an edge interrupt triggering while entering idle. So we need to also
add back the workaround for seeing if there are any pending edge
interrupts when waking up.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20201028060556.56038-1-tony@atomide.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIO_T is mapped to the most significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_T is input only. All
the other bits need to be 1 because GPIO_Q/R/S support both input and
output modes.
Fixes: ab4a85534c3e ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Commit 0ea683931adb ("gpio: dwapb: Convert driver to using the
GPIO-lib-based IRQ-chip") missed the case in dwapb_irq_set_wake().
Without this fix, probing the dwapb gpio driver will hit a error:
"address between user and kernel address ranges" on a Ampere armv8a
server and cause a panic.
Fixes: 0ea683931adb ("gpio: dwapb: Convert driver to using the GPIO-lib-based IRQ-chip")
Signed-off-by: Jia He <justin.he@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for initialising shared (between children) Regmaps
- Add support for Kontron SL28CPLD
- Add support for ENE KB3930 Embedded Controller
- Add support for Intel FPGA PAC MAX 10 BMC
New Device Support:
- Add support for Power to Ricoh RN5T618
- Add support for UART to Intel Lakefield
- Add support for LP87524_Q1 to Texas Instruments LP87565
New Functionality:
- Device Tree; ene-kb3930, sl28cpld, syscon, lp87565, lp87524-q1
- Use new helper dev_err_probe(); madera-core, stmfx, wcd934x
- Use new GPIOD API; dm355evm_msp
- Add wake-up capability; sprd-sc27xx-spi
- Add ACPI support; kempld-core
Fix-ups:
- Trivial (spelling/whitespace); Kconfig, ab8500
- Fix for unused variables; khadas-mcu, kempld-core
- Remove unused header file(s); mt6360-core
- Use correct IRQ flags in docs; act8945a, gateworks-gsc, rohm,bd70528-pmic
- Add COMPILE_TEST support; asic3, tmio_core
- Add dependency on I2C; SL28CPLD
Bug Fixes:
- Fix memory leak(s); sm501
- Do not free regmap_config's 'name' until exit; syscon"
* tag 'mfd-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (34 commits)
mfd: kempld-core: Fix unused variable 'kempld_acpi_table' when !ACPI
mfd: sl28cpld: Depend on I2C
mfd: asic3: Build if COMPILE_TEST=y
dt-bindings: mfd: Correct interrupt flags in examples
mfd: Add ACPI support to Kontron PLD driver
mfd: intel-m10-bmc: Add Intel MAX 10 BMC chip support for Intel FPGA PAC
mfd: lp87565: Add LP87524-Q1 variant
dt-bindings: mfd: Add LP87524-Q1
dt-bindings: mfd: lp87565: Convert to yaml
mfd: mt6360: Remove unused include <linux/version.h>
mfd: sm501: Fix leaks in probe()
mfd: syscon: Don't free allocated name for regmap_config
dt-bindings: mfd: syscon: Document Exynos3 and Exynos5433 compatibles
dt-bindings: mfd: syscon: Merge Samsung Exynos Sysreg bindings
dt-bindings: mfd: ab8500: Remove weird Unicode characters
mfd: sprd: Add wakeup capability for PMIC IRQ
mfd: intel-lpss: Add device IDs for UART ports for Lakefield
mfd: dm355evm_msp: Convert LEDs to GPIO descriptor table
mfd: wcd934x: Simplify with dev_err_probe()
mfd: stmfx: Simplify with dev_err_probe()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This time very little driver changes but lots of core changes.
We have some interesting cooperative work for ARM and Intel alike,
making the GPIO subsystem more and more suitable for industrial
systems and the like, in addition to the in-kernel users.
We touch driver core (device properties) and lib/* by adding one
simple string array free function, these are authored by Andy
Shevchenko who is a well known and recognized core helpers maintainers
so this should be fine.
We also see some Android GKI-related modularization in the MXC
drivers.
Core changes:
- The big core change is the updated (v2) userspace character device
API.
This corrects badly designed 64-bit alignment around the line
events. We also add the debounce request feature. This echoes the
often quotes passage from Frederick Brooks "The mythical man-month"
to always throw one away, which we have seen before in things such
as V4L2. So we put in a new one and deprecate and obsolete the old
one.
- All example tools in tools/gpio/* are migrated to the new API to
set a good example. The libgpiod userspace library has been
augmented to use this new API pretty much from day 1.
- Some misc API hardening by using strn* function calls has been
added as well.
- Use the simpler IDA interface for GPIO chip instance enumeration.
- Add device core function for counting string arrays in device
properties.
- Provide a generic library function kfree_strarray() that can be
used throughout the kernel.
Driver enhancements:
- The DesignWare dwapb-gpio driver has been enhanced and now uses the
IRQ handling in the gpiolib core.
- The mockup and aggregator drivers have seen some substantial code
clean-up and now use more of the core kernel inftrastructure.
- Misc cleanups using dev_err_probe().
- The MXC drivers (Freescale/NXP) can now be built modularized, which
makes modularized GKI Android kernels happy"
* tag 'gpio-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (73 commits)
gpiolib: Update header block in gpiolib-cdev.h
gpiolib: cdev: switch from kstrdup() to kstrndup()
docs: gpio: add a new document to its index.rst
gpio: pca953x: Add support for the NXP PCAL9554B/C
tools: gpio: add debounce support to gpio-event-mon
tools: gpio: add multi-line monitoring to gpio-event-mon
tools: gpio: port gpio-event-mon to v2 uAPI
tools: gpio: port gpio-hammer to v2 uAPI
tools: gpio: rename nlines to num_lines
tools: gpio: port gpio-watch to v2 uAPI
tools: gpio: port lsgpio to v2 uAPI
gpio: uapi: document uAPI v1 as deprecated
gpiolib: cdev: support setting debounce
gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL
gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL
gpiolib: cdev: support edge detection for uAPI v2
gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL
gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL
gpiolib: add build option for CDEV v1 ABI
gpiolib: make cdev a build option
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Allow trimming of interrupt hierarchy to support odd hardware
setups where only a subset of the interrupts requires the full
hierarchy.
- Allow the retrigger mechanism to follow a hierarchy to simplify
driver code.
- Provide a mechanism to force enable wakeup interrrupts on suspend.
- More infrastructure to handle IPIs in the core code
Architectures:
- Convert ARM/ARM64 IPI handling to utilize the interrupt core code.
Drivers:
- The usual pile of new interrupt chips (MStar, Actions Owl, TI
PRUSS, Designware ICTL)
- ARM(64) IPI related conversions
- Wakeup support for Qualcom PDC
- Prevent hierarchy corruption in the NVIDIA Tegra driver
- The usual small fixes, improvements and cleanups all over the
place"
* tag 'irq-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
dt-bindings: interrupt-controller: Add MStar interrupt controller
irqchip/irq-mst: Add MStar interrupt controller support
soc/tegra: pmc: Don't create fake interrupt hierarchy levels
soc/tegra: pmc: Allow optional irq parent callbacks
gpio: tegra186: Allow optional irq parent callbacks
genirq/irqdomain: Allow partial trimming of irq_data hierarchy
irqchip/qcom-pdc: Reset PDC interrupts during init
irqchip/qcom-pdc: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
genirq/PM: Introduce IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Use return value from irq_set_wake() call
pinctrl: qcom: Set IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags
ARM: Handle no IPI being registered in show_ipi_list()
MAINTAINERS: Add entries for Actions Semi Owl SIRQ controller
irqchip: Add Actions Semi Owl SIRQ controller
dt-bindings: interrupt-controller: Add Actions SIRQ controller binding
dt-bindings: dw-apb-ictl: Update binding to describe use as primary interrupt controller
irqchip/dw-apb-ictl: Add primary interrupt controller support
irqchip/dw-apb-ictl: Refactor priot to introducing hierarchical irq domains
genirq: Add stub for set_handle_irq() when !GENERIC_IRQ_MULTI_HANDLER
...
|
|
Make the tegra186 GPIO driver resistent to variable depth
interrupt hierarchy, which we are about to introduce.
No functionnal change yet.
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
The dev_t is defined in types.h while struct gpio_device forward declaration
is missed. Take into account above and update header block in gpiolib-cdev.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201005095622.73616-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use kstrndup() to copy line labels from the userspace provided char
array, rather than ensuring the char array contains a null terminator
and using kstrdup().
Note that the length provided to kstrndup() still assumes that the char
array does contain a null terminator, so the maximum string length is one
less than the array. This is consistent with the previous behaviour.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20201005070246.20927-1-warthog618@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pca953x driver never checks the result of irq_find_mapping(),
which returns 0 when no mapping is found. When a spurious interrupt
is delivered (which can happen under obscure circumstances), the
kernel explodes as it still tries to handle the error code as
a real interrupt.
Handle this particular case and warn on spurious interrupts.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201005140217.1390851-1-maz@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It appears that UML (arch/um) has no compat.h header defined and hence
can't compile a recently provided piece of code in GPIO library.
Disable compat ->read() code in UML case to avoid compilation errors.
While at it, use pattern which is already being used in the kernel elsewhere.
Fixes: 5ad284ab3a01 ("gpiolib: Fix line event handling in syscall compatible mode")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201005131044.87276-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some late GPIO fixes for the v5.9 series:
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the Spreadtrum
driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode for the
character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for bit
manipulation in the PCA953x driver"
* tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x
gpio: pca953x: Use bitmap API over implicit GCC extension
gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION
gpio: aspeed: fix ast2600 bank properties
gpio/aspeed-sgpio: don't enable all interrupts by default
gpio/aspeed-sgpio: enable access to all 80 input & output sgpios
gpio: pca953x: Fix uninitialized pending variable
gpiolib: Fix line event handling in syscall compatible mode
gpio: mockup: fix resource leak in error path
gpio: siox: explicitly support only threaded irqs
gpio: tc35894: fix up tc35894 interrupt configuration
gpio: sprd: Clear interrupt when setting the type as edge
gpio: omap: Fix warnings if PM is disabled
|
|
When driver has been converted to the bitmap API the non-bitmap functions
started behaving differently on 32-bit BE architectures since the bytes in
two consequent unsigned longs are in different order in comparison to byte
array. Hence if the chip had had more than 32 lines the memset() call over
it would have not set up upper lines correctly.
Although it's currently a theoretical case (no supported chips of this type
has 32+ lines), it's better to provide a clean code to avoid people thinking
this is okay and potentially producing not fully working things.
Fixes: 35d13d94893f ("gpio: pca953x: convert to use bitmap API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200930142013.59247-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In IRQ handler we have to clear bitmap before use. Currently
the GCC extension has been used for that. For sake of the consistency
switch to bitmap API. As expected bloat-o-meter shows no difference
in the object size.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200930142013.59247-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The NXP PCAL9554B is a variant of the PCA953x GPIO expander,
with 8 GPIOs, latched interrupts and some advanced configuration
options. The "C" version only differs in I2C address.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200930092053.2114-2-mike.looijmans@topic.nl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support for setting debounce on a line via the GPIO uAPI.
Where debounce is not supported by hardware, a software debounce is
provided.
The implementation of the software debouncer waits for the line to be
stable for the debounce period before determining if a level change,
and a corresponding edge event, has occurred. This provides maximum
protection against glitches, but also introduces a debounce_period
latency to edge events.
The software debouncer is integrated with the edge detection as it
utilises the line interrupt, and integration is simpler than getting
the two to interwork. Where software debounce AND edge detection is
required, the debouncer provides both.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add support for the GPIO_V2_LINE_SET_VALUES_IOCTL.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add support for GPIO_V2_LINE_SET_CONFIG_IOCTL, the uAPI v2
line set config ioctl.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add support for edge detection to lines requested using
GPIO_V2_GET_LINE_IOCTL.
The edge_detector implementation is based on the v1 lineevent
implementation. Unlike the v1 implementation, an overflow of the event
buffer results in discarding older events, rather than the most
recent, so the final event in a burst will correspond to the current
state of the line.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
GPIO_V2_GET_LINEINFO_WATCH_IOCTL
Add support for GPIO_V2_GET_LINEINFO_IOCTL and
GPIO_V2_GET_LINEINFO_WATCH_IOCTL.
The core of this change is the event kfifo switching to contain
struct gpioline_info_changed_v2, instead of v1 as v2 is richer.
The two uAPI versions are mostly independent - other than where they both
provide line info changes via reads on the chip fd. As the info change
structs differ between v1 and v2, the infowatch implementation tracks which
version of the infowatch ioctl, either GPIO_GET_LINEINFO_WATCH_IOCTL or
GPIO_V2_GET_LINEINFO_WATCH_IOCTL, initiates the initial watch and returns
the corresponding info change struct to the read. The version supported
on that fd locks to that version on the first watch request, so subsequent
watches from that process must use the same uAPI version.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add support for requesting lines using the GPIO_V2_GET_LINE_IOCTL, and
returning their current values using GPIO_V2_LINE_GET_VALUES_IOCTL.
The struct linereq implementation is based on the v1 struct linehandle
implementation.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add a build option to allow the removal of the CDEV v1 ABI.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Make the gpiolib-cdev module a build option. This allows the CDEV
interface to be removed from the kernel to reduce kernel size in
applications where is it not required, and provides the parent for
other CDEV interface specific build options to follow.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Replace usage of strncpy() with strscpy() to remove -Wstringop-truncation
warnings.
The structures being populated are zeroed, to prevent stack leakage as
they are returned to userspace, so strscpy() performs the equivalent
function without the warnings.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Set the value of the line info offset in gpio_desc_to_lineinfo(), rather
than relying on it being passed in the info. This makes the function
behave as you would expect from the name - it generates the line info
corresponding to a given GPIO desc.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Let's move the code preparing the device properties into a separate
routine. This has the advantage of simplifying the error handling and
makes the indentation less deep.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
GPIO line names are currently created by the driver from the chip label.
We'll want to support custom formats for line names (for instance: to
name all lines the same) for user-space tests so create them in the
module init function and pass them to the driver using the standard
'gpio-line-names' property.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
While we do check the "chip-name" property in probe(), we never actually
use it. Let's pass the chip label to the driver using device properties
as we'll want to allow users to define their own once dynamically
created chips are supported.
The property is renamed to "chip-label" to not cause any confusion with
the actual chip name which is of the form: "gpiochipX".
If the "chip-label" property is missing, let's do what most devices in
drivers/gpio/ do and use dev_name().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The driver actually supports 4 properties but we only ever set up up to
three. This will change however in upcoming patches so increase the
number of really (as in: the number the property array can hold)
supported properties to 4.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
There's a return; at the end of a void function. This is not needed so
remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
We don't need a custom logging helper. Let's use the standard pr_fmt()
macro which allows us to use all pr_*() routines with custom format.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Drop the definition for the driver name. Let's use KBUILD_MODNAME for
the log format and use the "gpio-mockup" value directly in the only
place where it's relevant: in the name of the device.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This module doesn't need gpio/consumer.h - it's a provider. It also
doesn't use any symbols from init.h so let's remove both includes.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Some Layerscape/QoriQ SoCs have input buffers which needs to be enabled
first. This was done in two different ways in the driver. Unify it.
This was tested on a LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
If the module init function fails after creating the debugs directory,
it's never removed. Add proper cleanup calls to avoid this resource
leak.
Fixes: 9202ba2397d1 ("gpio: mockup: implement event injecting over debugfs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Change config to tristate, add module device table, module author,
description and license to support module build for i.MX GPIO driver.
As this is a SoC GPIO module, it provides common functions for most
of the peripheral devices, such as GPIO pins control, secondary
interrupt controller for GPIO pins IRQ etc., without GPIO driver, most
of the peripheral devices will NOT work properly, so GPIO module is
similar with clock, pinctrl driver that should be loaded ONCE and
never unloaded.
Since MXC GPIO driver needs to have init function to register syscore
ops once, here still use subsys_initcall(), NOT module_platform_driver().
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1600320829-1453-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The original commit appears to have the logic reversed in
amd_fch_gpio_get_direction. Also confirmed by observing the value of
"direction" in the sys tree.
Signed-off-by: Ed Wildgoose <lists@wildgooses.com>
Fixes: e09d168f13f0 ("gpio: AMD G-Series PCH gpio driver")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
GPIO_U is mapped to the least significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_U is input only. All
the other bits need to be 1 because GPIO_V/W/X support both input and
output modes.
Similarly, GPIO_Y/Z are mapped to the 2 least significant bytes, and the
according bits need to be 1 because GPIO_Y/Z support both input and
output modes.
Fixes: ab4a85534c3e ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
When pca953x_irq_pending returns false, the pending parameter won't
be set. But pca953x_irq_handler continues using this uninitialized
variable as pending irqs and will cause problem.
Fix the issue by initializing pending to 0.
Fixes: 064c73afe738 ("gpio: pca953x: Synchronize interrupt handler properly")
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.10 - part 1
- automatically drive GPHY leds in gpio-stp-xway
- refactor ->{get, set}_multiple() in gpio-aggregator
- add support for a new model in rcar-gpio DT bindings
- simplify several GPIO drivers with dev_err_probe()
- disable Direct KBD interrupts in gpio-tc35894
- use DEFINE_SEQ_ATTRIBUTE() in GPIO chardev to shrink code
- switch to using a simpler IDA API in gpiolib
- make devprop_gpiochip_set_names() more generic by using device properties
instead of using fwnode helpers
|
|
Add support for the GPIO controller of the sl28 board management
controller. This driver is part of a multi-function device.
A controller has 8 lines. There are three different flavors:
full-featured GPIO with interrupt support, input-only and output-only.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
It's possible for a GPIO chip to not have a parent device (whose
properties we inspect for 'gpio-line-names'). In this case we should
simply return from devprop_gpiochip_set_names(). Add an appropriate
check for this use-case.
Fixes: 7cba1a4d5e16 ("gpiolib: generalize devprop_gpiochip_set_names() for device properties")
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
