summaryrefslogtreecommitdiffstats
path: root/drivers/dma/dw/of.c
AgeCommit message (Collapse)Author
2020-08-17dmaengine: dw: Add DMA-channels mask cell supportSerge Semin
DW DMA IP-core provides a way to synthesize the DMA controller with channels having different parameters like maximum burst-length, multi-block support, maximum data width, etc. Those parameters both explicitly and implicitly affect the channels performance. Since DMA slave devices might be very demanding to the DMA performance, let's provide a functionality for the slaves to be assigned with DW DMA channels, which performance according to the platform engineer fulfill their requirements. After this patch is applied it can be done by passing the mask of suitable DMA-channels either directly in the dw_dma_slave structure instance or as a fifth cell of the DMA DT-property. If mask is zero or not provided, then there is no limitation on the channels allocation. For instance Baikal-T1 SoC is equipped with a DW DMAC engine, which first two channels are synthesized with max burst length of 16, while the rest of the channels have been created with max-burst-len=4. It would seem that the first two channels must be faster than the others and should be more preferable for the time-critical DMA slave devices. In practice it turned out that the situation is quite the opposite. The channels with max-burst-len=4 demonstrated a better performance than the channels with max-burst-len=16 even when they both had been initialized with the same settings. The performance drop of the first two DMA-channels made them unsuitable for the DW APB SSI slave device. No matter what settings they are configured with, full-duplex SPI transfers occasionally experience the Rx FIFO overflow. It means that the DMA-engine doesn't keep up with incoming data pace even though the SPI-bus is enabled with speed of 25MHz while the DW DMA controller is clocked with 50MHz signal. There is no such problem has been noticed for the channels synthesized with max-burst-len=4. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200731200826.9292-6-Sergey.Semin@baikalelectronics.ru Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-07-27dmaengine: dw: Introduce max burst length hw configSerge Semin
IP core of the DW DMA controller may be synthesized with different max burst length of the transfers per each channel. According to Synopsis having the fixed maximum burst transactions length may provide some performance gain. At the same time setting up the source and destination multi size exceeding the max burst length limitation may cause a serious problems. In our case the DMA transaction just hangs up. In order to fix this lets introduce the max burst length platform config of the DW DMA controller device and don't let the DMA channels configuration code exceed the burst length hardware limitation. Note the maximum burst length parameter can be detected either in runtime from the DWC parameter registers or from the dedicated DT property. Depending on the IP core configuration the maximum value can vary from channel to channel so by overriding the channel slave max_burst capability we make sure a DMA consumer will get the channel-specific max burst length. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200723005848.31907-10-Sergey.Semin@baikalelectronics.ru Signed-off-by: Vinod Koul <vkoul@kernel.org>
2019-08-21dmaengine: dw: platform: Split OF helpers to separate moduleAndy Shevchenko
For better maintenance split OF helpers to the separate module. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20190820131546.75744-11-andriy.shevchenko@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>