Age | Commit message (Collapse) | Author |
|
Mark the SCLK clock for Exynos5433 I2S1 device with IGNORE_UNUSED flag to
match its behaviour with SCLK clock for AUD_I2S (I2S0) device until
a proper fix for Exynos I2S driver is ready.
This fixes the following synchronous abort issue revealed by the probe
order change caused by the commit 93d2e4322aa7 ("of: platform: Batch
fwnode parsing when adding all top level devices")
Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 50 Comm: kworker/0:1 Not tainted 5.7.0-rc5+ #701
Hardware name: Samsung TM2E board (DT)
Workqueue: events deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : samsung_i2s_probe+0x768/0x8f0
lr : samsung_i2s_probe+0x688/0x8f0
...
Call trace:
samsung_i2s_probe+0x768/0x8f0
platform_drv_probe+0x50/0xa8
really_probe+0x108/0x370
driver_probe_device+0x54/0xb8
__device_attach_driver+0x90/0xc0
bus_for_each_drv+0x70/0xc8
__device_attach+0xdc/0x140
device_initial_probe+0x10/0x18
bus_probe_device+0x94/0xa0
deferred_probe_work_func+0x70/0xa8
process_one_work+0x2a8/0x718
worker_thread+0x48/0x470
kthread+0x134/0x160
ret_from_fork+0x10/0x1c
Code: 17ffffaf d503201f f94086c0 91003000 (88dffc00)
---[ end trace ccf721c9400ddbd6 ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Convert the various uses of fallthrough comments to fallthrough;
Done via script
Link: https://lore.kernel.org/lkml/b56602fcf79f849e733e7b521bb0e17895d390fa.1582230379.git.joe@perches.com/
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C part
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
The proper name for CLK_SMMU_FIMCL3 is "smmu_fimcl3". Remove obvious
typo.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
The TOP 'aclk*_isp', 'aclk550_cam', 'gscl_wa' and 'gscl_wb' clocks must
be kept enabled all the time to allow proper access to power management
control for the ISP and CAM power domains. The last two clocks, although
related to GScaler device and GSCL power domain, provides also the
I_WRAP_CLK signal to MIPI CSIS0/1 devices, which are a part of CAM power
domain and are needed for proper power on/off sequence.
Currently there are no drivers for the devices, which are part of CAM and
ISP power domains yet. This patch only fixes the race between disabling
the unused power domains and disabling unused clocks, which randomly
resulted in the following error during boot:
Power domain CAM disable failed
Power domain ISP disable failed
Fixes: 318fa46cc60d ("clk/samsung: exynos542x: mark some clocks as critical")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Consistent with other instances of samsung_clk_init, the check
if ctx is NULL is redundant. The function currently does not
return NULL.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Link: https://lkml.kernel.org/r/20200121233349.28627-1-pakki001@umn.edu
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In Exynos542x/5800 SoCs, the G3D leaf clocks are located in the G3D power
domain. This is similar to the other hardware modules and their power
domains. However there is one thing specific to G3D clocks hierarchy.
Unlike other hardware modules, the G3D clocks hierarchy doesn't have any
gate clock between the TOP part of the hierarchy and the part located in
the power domain and some SoC internal busses are sourced directly from
the TOP muxes. The consequence of this design if the fact that the TOP
part of the hierarchy has to be enabled permanently to ensure proper
operation of the SoC power related components (G3D power domain and
Exynos Power Management Unit for system suspend/resume).
This patch adds an explicit call to clk_prepare_enable() on the last MUX
in the TOP part of G3D clock hierarchy to keep it enabled permanently to
ensure that the internal busses get their clock regardless of the main
G3D clock enablement status.
This fixes following imprecise abort issue observed on Odroid XU3/XU4
after enabling Panfrost driver by commit 1a5a85c56402 "ARM: dts: exynos:
Add Mali/GPU node on Exynos5420 and enable it on Odroid XU3/4"):
panfrost 11800000.gpu: clock rate = 400000000
panfrost 11800000.gpu: failed to get regulator: -517
panfrost 11800000.gpu: regulator init failed -517
Power domain G3D disable failed
...
panfrost 11800000.gpu: clock rate = 400000000
8<--- cut here ---
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=00000000
Internal error: : 1406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 7 PID: 53 Comm: kworker/7:1 Not tainted 5.4.0-rc8-next-20191119-00032-g56f1001191a6 #6923
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at panfrost_gpu_soft_reset+0x94/0x110
LR is at ___might_sleep+0x128/0x2dc
...
[<c05c231c>] (panfrost_gpu_soft_reset) from [<c05c2704>] (panfrost_gpu_init+0x10/0x67c)
[<c05c2704>] (panfrost_gpu_init) from [<c05c15d0>] (panfrost_device_init+0x158/0x2cc)
[<c05c15d0>] (panfrost_device_init) from [<c05c0cb0>] (panfrost_probe+0x80/0x178)
[<c05c0cb0>] (panfrost_probe) from [<c05cfaa0>] (platform_drv_probe+0x48/0x9c)
[<c05cfaa0>] (platform_drv_probe) from [<c05cd20c>] (really_probe+0x1c4/0x474)
[<c05cd20c>] (really_probe) from [<c05cd694>] (driver_probe_device+0x78/0x1bc)
[<c05cd694>] (driver_probe_device) from [<c05cb374>] (bus_for_each_drv+0x74/0xb8)
[<c05cb374>] (bus_for_each_drv) from [<c05ccfa8>] (__device_attach+0xd4/0x16c)
[<c05ccfa8>] (__device_attach) from [<c05cc110>] (bus_probe_device+0x88/0x90)
[<c05cc110>] (bus_probe_device) from [<c05cc634>] (deferred_probe_work_func+0x4c/0xd0)
[<c05cc634>] (deferred_probe_work_func) from [<c0149df0>] (process_one_work+0x300/0x864)
[<c0149df0>] (process_one_work) from [<c014a3ac>] (worker_thread+0x58/0x5a0)
[<c014a3ac>] (worker_thread) from [<c0151174>] (kthread+0x12c/0x160)
[<c0151174>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xee03dfb0 to 0xee03dff8)
...
Code: e594300c e5933020 e3130c01 1a00000f (ebefff50).
---[ end trace badde2b74a65a540 ]---
In the above case, the Panfrost driver disables G3D clocks after failure
of getting the needed regulator and return with -EPROVE_DEFER code. This
causes G3D power domain disable failure and then, during second probe
an imprecise abort is triggered due to undefined power domain state.
Fixes: 45f10dabb56b ("clk: samsung: exynos5420: Add SET_RATE_PARENT flag to clocks on G3D path")
Fixes: c9f7567aff31 ("clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lkml.kernel.org/r/20191216131407.17225-1-m.szyprowski@samsung.com
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
'clk-aspeed' into clk-next
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Use struct_size() some more in various clk drivers
* clk-ti:
clk/ti/adpll: allocate room for terminating null
ARM: dts: omap3: fix DPLL4 M4 divider max value
clk: ti: divider: convert to use min,max,mask instead of width
clk: ti: divider: cleanup ti_clk_parse_divider_data API
clk: ti: divider: cleanup _register_divider and ti_clk_get_div_table
clk: ti: am43xx: drop idlest polling from gfx clock
clk: ti: am33xx: drop idlest polling from gfx clock
clk: ti: am33xx: drop idlest polling from pruss clkctrl clock
clk: ti: am43xx: drop idlest polling from pruss clkctrl clock
clk: ti: omap5: Drop idlest polling from IPU & DSP clkctrl clocks
clk: ti: omap4: Drop idlest polling from IPU & DSP clkctrl clocks
clk: ti: dra7xx: Drop idlest polling from IPU & DSP clkctrl clocks
clk: ti: omap5: add IVA subsystem clkctrl data
dt-bindings: clk: add omap5 iva clkctrl definitions
clk: ti: clkctrl: add new exported API for checking standby info
clk: ti: clkctrl: convert to use bit helper macros instead of bitops
clk: ti: clkctrl: fix setting up clkctrl clocks
* clk-allwinner:
clk: sunxi-ng: h3: Export MBUS clock
clk: sunxi-ng: h6: Allow GPU to change parent rate
clk: sunxi-ng: h6: Use sigma-delta modulation for audio PLL
* clk-qcom:
clk: qcom: rpmh: Reuse sdm845 clks for sm8150
clk: qcom: Add MSM8998 GPU Clock Controller (GPUCC) driver
clk: qcom: Allow constant ratio freq tables for rcg
clk: qcom: smd: Add missing pnoc clock
clk: qcom: Enumerate clocks and reset needed to boot the 8998 modem
clk: qcom: clk-rpmh: Add support for RPMHCC for SC7180
dt-bindings: clock: Introduce RPMHCC bindings for SC7180
dt-bindings: clock: Add YAML schemas for the QCOM RPMHCC clock bindings
clk: qcom: Add Global Clock controller (GCC) driver for SC7180
dt-bindings: clock: Add sc7180 GCC clock binding
dt-bindings: clock: Add YAML schemas for the QCOM GCC clock bindings
clk: qcom: common: Return NULL from clk_hw OF provider
clk: qcom: rcg: update the DFS macro for RCG
clk: qcom: remove unneeded semicolon
clk: qcom: Add Q6SSTOP clock controller for QCS404
dt-bindings: clock: qcom: Add QCOM Q6SSTOP clock controller bindings
* clk-sa:
drivers/clk: convert VL struct to struct_size
* clk-aspeed:
clk: aspeed: Add RMII RCLK gates for both AST2500 MACs
clk: ast2600: Add RMII RCLK gates for all four MACs
dt-bindings: clock: Add AST2600 RMII RCLK gate definitions
dt-bindings: clock: Add AST2500 RMII RCLK definitions
|
|
'clk-imx' into clk-next
* clk-hisi:
clk: hi6220: use CLK_OF_DECLARE_DRIVER
* clk-amlogic:
clk: meson: axg-audio: use devm_platform_ioremap_resource() to simplify code
clk: meson: axg_audio: add sm1 support
clk: meson: axg-audio: provide clk top signal name
clk: meson: axg-audio: prepare sm1 addition
clk: meson: axg-audio: fix regmap last register
clk: meson: axg-audio: remove useless defines
dt-bindings: clock: meson: add sm1 resets to the axg-audio controller
dt-bindings: clk: axg-audio: add sm1 bindings
clk: meson: g12a: set CLK_MUX_ROUND_CLOSEST on the cpu clock muxes
clk: meson: g12a: fix cpu clock rate setting
clk: meson: gxbb: let sar_adc_clk_div set the parent clock rate
* clk-samsung:
clk: samsung: exynos5420: Add SET_RATE_PARENT flag to clocks on G3D path
clk: samsung: exynos5420: Preserve CPU clocks configuration during suspend/resume
clk: samsung: exynos5420: Add VPLL rate table
clk: samsung: exynos5420: Preserve PLL configuration during suspend/resume
clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU
clk: samsung: exynos5433: Fix error paths
* clk-renesas: (23 commits)
clk: renesas: r8a7796: Add R8A77961 CPG/MSSR support
clk: renesas: Rename CLK_R8A7796 to CLK_R8A77960
dt-bindings: clock: renesas: cpg-mssr: Document r8a77961 support
clk: renesas: r8a77965: Remove superfluous semicolon
dt-bindings: clock: renesas: rcar-usb2-clock-sel: Fix typo in example
dt-bindings: clock: renesas: Remove R-Car Gen2 legacy DT bindings
dt-bindings: clock: Add r8a77961 CPG Core Clock Definitions
dt-bindings: power: Add r8a77961 SYSC power domain definitions
clk: renesas: rcar-gen3: Switch SD clocks to .determine_rate()
clk: renesas: rcar-gen3: Switch Z clocks to .determine_rate()
clk: renesas: rcar-gen2: Switch Z clock to .determine_rate()
clk: renesas: r8a774b1: Add TMU clock
clk: renesas: cpg-mssr: Add r8a774b1 support
dt-bindings: clock: renesas: cpg-mssr: Document r8a774b1 binding
clk: renesas: rcar-gen3: Loop to find best rate in cpg_sd_clock_round_rate()
clk: renesas: rcar-gen3: Absorb cpg_sd_clock_calc_div()
clk: renesas: rcar-gen3: Avoid double table iteration in SD .set_rate()
clk: renesas: rcar-gen3: Improve arithmetic divisions
clk: renesas: rcar-gen2: Improve arithmetic divisions
clk: renesas: Remove R-Car Gen2 legacy DT clock support
...
* clk-imx:
clk: imx: imx8mq: fix sys3_pll_out_sels
clk: imx7ulp: do not export out IMX7ULP_CLK_MIPI_PLL clock
clk: imx: imx6ul: use imx_obtain_fixed_clk_hw to simplify code
clk: imx: imx6sx: use imx_obtain_fixed_clk_hw to simplify code
clk: imx: imx6sll: use imx_obtain_fixed_clk_hw to simplify code
clk: imx: imx7d: use imx_obtain_fixed_clk_hw to simplify code
clk: imx7ulp: Correct DDR clock mux options
clk: imx7ulp: Correct system clock source option #7
clk: imx: imx8mq: mark sys1/2_pll as fixed clock
clk: imx: imx8mn: mark sys_pll1/2 as fixed clock
clk: imx: imx8mm: mark sys_pll1/2 as fixed clock
clk: imx8mn: Define gates for pll1/2 fixed dividers
clk: imx8mm: Define gates for pll1/2 fixed dividers
clk: imx8mq: Define gates for pll1/2 fixed dividers
clk: imx: clk-pll14xx: Make two variables static
clk: imx8mq: Add VIDEO2_PLL clock
clk: imx8mn: Use common 1443X/1416X PLL clock structure
clk: imx8mm: Move 1443X/1416X PLL clock structure to common place
clk: imx: pll14xx: Fix quick switch of S/K parameter
|
|
There are a few manually-calculated variable-length struct allocations
left, this converts them to use struct_size. Found with the following
git grep command
git grep -A1 'kzalloc.*sizeof[^_].*+'
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lkml.kernel.org/r/20190927185110.29897-1-steve@sk2.org
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
[sboyd@kernel.org: Add grep command]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add CLK_SET_RATE_PARENT flag to all clocks on the path from VPLL to G3D,
so the G3D MALI driver can simply adjust the rate of its clock by doing
a single clk_set_rate() call, without the need to know the whole clock
topology in Exynos542x SoCs.
Suggested-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
suspend/resume
Save and restore top PLL related configuration registers for big (APLL)
and LITTLE (KPLL) cores during suspend/resume cycle. So far, CPU clocks
were reset to default values after suspend/resume cycle and performance
after system resume was affected when performance governor has been selected.
Fixes: 773424326b51 ("clk: samsung: exynos5420: add more registers to restore list")
Signed-off-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Add new table rate for VPLL for Exynos 542x SoC required to support
Mali GPU clock frequencies.
Signed-off-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Properly save and restore all top PLL related configuration registers
during suspend/resume cycle. So far driver only handled EPLL and RPLL
clocks, all other were reset to default values after suspend/resume cycle.
This caused for example lower G3D (MALI Panfrost) performance after system
resume, even if performance governor has been selected.
Reported-by: Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Fixes: 773424326b51 ("clk: samsung: exynos5420: add more registers to restore list")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
G3D clocks require special handling of their parent bus clock during power
domain on/off sequences. Those clocks were not initially added to the
sub-CMU handler, because that time there was no open-source driver for the
G3D (MALI Panfrost) hardware module and it was not possible to test it.
This patch fixes this issue. Parent clock for G3D hardware block is now
properly preserved during G3D power domain on/off sequence. This restores
proper MALI Panfrost performance broken by commit 8686764fc071
("ARM: dts: exynos: Add G3D power domain to Exynos542x").
Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Fixes: b06a532bf1fa ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marian Mihailescu <mihailescu2m@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Add checking the value returned by samsung_clk_alloc_reg_dump() and
devm_kcalloc(). While fixing this, also release all gathered clocks.
Fixes: 523d3de41f02 ("clk: samsung: exynos5433: Add support for runtime PM")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
[s.nawrocki: squashed patch from K. Kozlowski adding missing slab.h header]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lkml.kernel.org/r/20191015142424.25944-1-yuehaibing@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
M2M scaler clocks require special handling of their parent bus clock during
power domain on/off sequences. MSCL clocks were not initially added to the
sub-CMU handler, because that time there was no driver for the M2M scaler
device and it was not possible to test it.
This patch fixes this issue. Parent clock for M2M scaler devices is now
properly preserved during MSC power domain on/off sequence. This gives M2M
scaler devices proper performance: fullHD XRGB32 image 1000 rotations test
takes 3.17s instead of 45.08s.
Fixes: b06a532bf1fa ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lkml.kernel.org/r/20190808121839.23892-1-m.szyprowski@samsung.com
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This patch fixes broken sound on Exynos5422/5800 platforms after
system/suspend resume cycle in cases where the audio root clock
is derived from MAU_EPLL_CLK.
In order to preserve state of the USER_MUX_MAU_EPLL_CLK clock mux
during system suspend/resume cycle for Exynos5800 we group the MAU
block input clocks in "MAU" sub-CMU and add the clock mux control
bit to .suspend_regs. This ensures that user configuration of the mux
is not lost after the PMU block changes the mux setting to OSC_DIV
when switching off the MAU power domain.
Adding the SRC_TOP9 register to exynos5800_clk_regs[] array is not
sufficient as at the time of the syscore_ops suspend call MAU power
domain is already turned off and we already save and subsequently
restore an incorrect register's value.
Fixes: b06a532bf1fa ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Reported-by: Jaafar Ali <jaafarkhalaf@gmail.com>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Jaafar Ali <jaafarkhalaf@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lkml.kernel.org/r/20190808144929.18685-2-s.nawrocki@samsung.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In order to make it easier in subsequent patch to create different subcmu
lists for exynos5420 and exynos5800 SoCs the code is rewritten so we pass
an array of pointers to the subcmus initialization function.
Fixes: b06a532bf1fa ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Tested-by: Jaafar Ali <jaafarkhalaf@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lkml.kernel.org/r/20190808144929.18685-1-s.nawrocki@samsung.com
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add ID and gate for bus clock for GPU (Mali 400) on Exynos4412.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This patch provides support for clocks needed for Dynamic Memory Controller
in Exynos5422 SoC. It adds CDREX base register addresses, new DIV, MUX and
GATE entries.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Add new table rate for BPLL for Exynos5422 SoC supporting Dynamic Memory
Controller frequencies for driver's DRAM timings.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Use of_clk_get_parent_count() instead of open coding.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we've gotten rid of clk_readl() we can remove io.h from the
clk-provider header and push out the io.h include to any code that isn't
already including the io.h header but using things like readl/writel,
etc.
Found with this grep:
git grep -l clk-provider.h | grep '.c$' | xargs git grep -L 'linux/io.h' | \
xargs git grep -l \
-e '\<__iowrite32_copy\>' --or \
-e '\<__ioread32_copy\>' --or \
-e '\<__iowrite64_copy\>' --or \
-e '\<ioremap_page_range\>' --or \
-e '\<ioremap_huge_init\>' --or \
-e '\<arch_ioremap_pud_supported\>' --or \
-e '\<arch_ioremap_pmd_supported\>' --or \
-e '\<devm_ioport_map\>' --or \
-e '\<devm_ioport_unmap\>' --or \
-e '\<IOMEM_ERR_PTR\>' --or \
-e '\<devm_ioremap\>' --or \
-e '\<devm_ioremap_nocache\>' --or \
-e '\<devm_ioremap_wc\>' --or \
-e '\<devm_iounmap\>' --or \
-e '\<devm_ioremap_release\>' --or \
-e '\<devm_memremap\>' --or \
-e '\<devm_memunmap\>' --or \
-e '\<__devm_memremap_pages\>' --or \
-e '\<pci_remap_cfgspace\>' --or \
-e '\<arch_has_dev_port\>' --or \
-e '\<arch_phys_wc_add\>' --or \
-e '\<arch_phys_wc_del\>' --or \
-e '\<memremap\>' --or \
-e '\<memunmap\>' --or \
-e '\<arch_io_reserve_memtype_wc\>' --or \
-e '\<arch_io_free_memtype_wc\>' --or \
-e '\<__io_aw\>' --or \
-e '\<__io_pbw\>' --or \
-e '\<__io_paw\>' --or \
-e '\<__io_pbr\>' --or \
-e '\<__io_par\>' --or \
-e '\<__raw_readb\>' --or \
-e '\<__raw_readw\>' --or \
-e '\<__raw_readl\>' --or \
-e '\<__raw_readq\>' --or \
-e '\<__raw_writeb\>' --or \
-e '\<__raw_writew\>' --or \
-e '\<__raw_writel\>' --or \
-e '\<__raw_writeq\>' --or \
-e '\<readb\>' --or \
-e '\<readw\>' --or \
-e '\<readl\>' --or \
-e '\<readq\>' --or \
-e '\<writeb\>' --or \
-e '\<writew\>' --or \
-e '\<writel\>' --or \
-e '\<writeq\>' --or \
-e '\<readb_relaxed\>' --or \
-e '\<readw_relaxed\>' --or \
-e '\<readl_relaxed\>' --or \
-e '\<readq_relaxed\>' --or \
-e '\<writeb_relaxed\>' --or \
-e '\<writew_relaxed\>' --or \
-e '\<writel_relaxed\>' --or \
-e '\<writeq_relaxed\>' --or \
-e '\<readsb\>' --or \
-e '\<readsw\>' --or \
-e '\<readsl\>' --or \
-e '\<readsq\>' --or \
-e '\<writesb\>' --or \
-e '\<writesw\>' --or \
-e '\<writesl\>' --or \
-e '\<writesq\>' --or \
-e '\<inb\>' --or \
-e '\<inw\>' --or \
-e '\<inl\>' --or \
-e '\<outb\>' --or \
-e '\<outw\>' --or \
-e '\<outl\>' --or \
-e '\<inb_p\>' --or \
-e '\<inw_p\>' --or \
-e '\<inl_p\>' --or \
-e '\<outb_p\>' --or \
-e '\<outw_p\>' --or \
-e '\<outl_p\>' --or \
-e '\<insb\>' --or \
-e '\<insw\>' --or \
-e '\<insl\>' --or \
-e '\<outsb\>' --or \
-e '\<outsw\>' --or \
-e '\<outsl\>' --or \
-e '\<insb_p\>' --or \
-e '\<insw_p\>' --or \
-e '\<insl_p\>' --or \
-e '\<outsb_p\>' --or \
-e '\<outsw_p\>' --or \
-e '\<outsl_p\>' --or \
-e '\<ioread8\>' --or \
-e '\<ioread16\>' --or \
-e '\<ioread32\>' --or \
-e '\<ioread64\>' --or \
-e '\<iowrite8\>' --or \
-e '\<iowrite16\>' --or \
-e '\<iowrite32\>' --or \
-e '\<iowrite64\>' --or \
-e '\<ioread16be\>' --or \
-e '\<ioread32be\>' --or \
-e '\<ioread64be\>' --or \
-e '\<iowrite16be\>' --or \
-e '\<iowrite32be\>' --or \
-e '\<iowrite64be\>' --or \
-e '\<ioread8_rep\>' --or \
-e '\<ioread16_rep\>' --or \
-e '\<ioread32_rep\>' --or \
-e '\<ioread64_rep\>' --or \
-e '\<iowrite8_rep\>' --or \
-e '\<iowrite16_rep\>' --or \
-e '\<iowrite32_rep\>' --or \
-e '\<iowrite64_rep\>' --or \
-e '\<__io_virt\>' --or \
-e '\<pci_iounmap\>' --or \
-e '\<virt_to_phys\>' --or \
-e '\<phys_to_virt\>' --or \
-e '\<ioremap_uc\>' --or \
-e '\<ioremap\>' --or \
-e '\<__ioremap\>' --or \
-e '\<iounmap\>' --or \
-e '\<ioremap\>' --or \
-e '\<ioremap_nocache\>' --or \
-e '\<ioremap_uc\>' --or \
-e '\<ioremap_wc\>' --or \
-e '\<ioremap_wc\>' --or \
-e '\<ioremap_wt\>' --or \
-e '\<ioport_map\>' --or \
-e '\<ioport_unmap\>' --or \
-e '\<ioport_map\>' --or \
-e '\<ioport_unmap\>' --or \
-e '\<xlate_dev_kmem_ptr\>' --or \
-e '\<xlate_dev_mem_ptr\>' --or \
-e '\<unxlate_dev_mem_ptr\>' --or \
-e '\<virt_to_bus\>' --or \
-e '\<bus_to_virt\>' --or \
-e '\<memset_io\>' --or \
-e '\<memcpy_fromio\>' --or \
-e '\<memcpy_toio\>'
I also reordered a couple includes when they weren't alphabetical and
removed clk.h from kona, replacing it with clk-provider.h because
that driver doesn't use clk consumer APIs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add the gate clock for ADC block on Exynos5410.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
'clk-rockchip' into clk-next
- Convert a few clk bindings to JSON schema format
- 3rd ECO fix for Mediatek MT2712 SoCs
* clk-typo:
clk: samsung: fix typo
* clk-json-schema:
dt-bindings: clock: Convert fixed-factor-clock to json-schema
dt-bindings: clock: Convert fixed-clock binding to json-schema
* clk-mtk-2712-eco:
clk: mediatek: update clock driver of MT2712
dt-bindings: clock: add clock for MT2712
* clk-rockchip:
clk: rockchip: add CLK_SET_RATE_PARENT for rk3066 lcdc dclks
clk: rockchip: fix frac settings of GPLL clock for rk3328
|
|
'clk-mmp2-lcdc' into clk-next
- Split LCDC into two clks on the Marvell MMP2 SoC
* clk-imx:
clk: imx8mq: add GPIO clocks to clock tree
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: imx: imx8mm: Mark init function __init
clk: imx8mq: Add the missing ARM clock
dt-bindings: imx8mq-clock: Add the missing ARM clock
clk: imx: imx8mq: Fix the rate propagation for arm pll
clk: imx8mq: Add support for the CLKO1 clock
clk: imx8mq: Fix the CLKO2 source select list
clk: imx8mq: Add missing M4 clocks
clk: imx: Add clock driver support for imx8mm
dt-bindings: imx: Add clock binding doc for imx8mm
clk: imx: Add PLLs driver for imx8mm soc
clk: imx5: add imx5_SCC2_IPG_GATE
clk: imx: scu: add set parent support
clk: imx: scu: add fallback compatible string support
clk: imx8mq: Make parent names arrays const pointers
clk: imx: Make parents const pointer in mux wrappers
clk: imx: Make parent_names const pointer in composite-8m
* clk-samsung:
clk: samsung: s3c2443: Mark expected switch fall-through
clk: samsung: exynos5: Fix kfree() of const memory on setting driver_override
clk: samsung: exynos5: Fix possible NULL pointer exception on platform_device_alloc() failure
clk: samsung: exynos5433: Add selected IMEM clocks
clk: samsung: dt-bindings: Document Exynos5433 IMEM CMU
clk: samsung: exynos5433: Fix name typo in sssx
clk: samsung: exynos5433: Fix definition of CLK_ACLK_IMEM_{200, 266} clocks
clk: samsung: dt-bindings: Add Exynos5433 IMEM CMU clock IDs
* clk-ti:
clk: clk-twl6040: Fix imprecise external abort for pdmclk
ARM: OMAP2+: hwmod: disable ick autoidling when a hwmod requires that
clk: ti: check clock type before doing autoidle ops
clk: ti: add a usecount for autoidle
clk: ti: generalize the init sequence of clk_hw_omap clocks
clk: ti: remove usage of CLK_IS_BASIC
clk: ti: add new API for checking if a provided clock is an OMAP clock
clk: ti: move clk_hw_omap list handling under generic part of the driver
* clk-uniphier-gear:
clk: uniphier: Fix update register for CPU-gear
* clk-mmp2-lcdc:
clk: mmp2: separate LCDC peripheral clk form the display clock
dt-bindings: marvell,mmp2: Add clock id for the LCDC clock
|
|
'clk-socfpga-parent' and 'clk-struct-size' into clk-next
- Various DT of_node refcount fixes
- Support for fixed rate clks populated from an MMIO register
- Remove clps711x driver as the board support is gone
* clk-of-refcount:
clk: dove: fix refcount leak in dove_clk_init()
clk: mv98dx3236: fix refcount leak in mv98dx3236_clk_init()
clk: armada-xp: fix refcount leak in axp_clk_init()
clk: kirkwood: fix refcount leak in kirkwood_clk_init()
clk: armada-370: fix refcount leak in a370_clk_init()
clk: vf610: fix refcount leak in vf610_clocks_init()
clk: imx7d: fix refcount leak in imx7d_clocks_init()
clk: imx6sx: fix refcount leak in imx6sx_clocks_init()
clk: imx6q: fix refcount leak in imx6q_clocks_init()
clk: samsung: exynos4: fix refcount leak in exynos4_get_xom()
clk: socfpga: fix refcount leak
clk: ti: fix refcount leak in ti_dt_clocks_register()
clk: qoriq: fix refcount leak in clockgen_init()
clk: highbank: fix refcount leak in hb_clk_init()
* clk-mmio-fixed-clock:
clk: Add Fixed MMIO clock driver
dt-bindings: clk: Add bindings for Fixed MMIO clock
* clk-remove-clps:
clk: clps711x: Remove board support
* clk-socfpga-parent:
clk: socfpga: Don't have get_parent for single parent ops
* clk-struct-size:
clk: imx: imx7ulp: use struct_size() in kzalloc()
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/clk/samsung/clk-s3c2443.c: In function ‘s3c2443_common_clk_init’:
drivers/clk/samsung/clk-s3c2443.c:390:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
samsung_clk_register_alias(ctx, s3c2450_aliases,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
ARRAY_SIZE(s3c2450_aliases));
~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/clk/samsung/clk-s3c2443.c:393:2: note: here
case S3C2416:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Platform driver driver_override field should not be initialized from
const memory because the core later kfree() it. If driver_override is
manually set later through sysfs, kfree() of old value leads to:
$ echo "new_value" > /sys/bus/platform/drivers/.../driver_override
kernel BUG at ../mm/slub.c:3960!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
...
(kfree) from [<c058e8c0>] (platform_set_driver_override+0x84/0xac)
(platform_set_driver_override) from [<c058e908>] (driver_override_store+0x20/0x34)
(driver_override_store) from [<c031f778>] (kernfs_fop_write+0x100/0x1dc)
(kernfs_fop_write) from [<c0296de8>] (__vfs_write+0x2c/0x17c)
(__vfs_write) from [<c02970c4>] (vfs_write+0xa4/0x188)
(vfs_write) from [<c02972e8>] (ksys_write+0x4c/0xac)
(ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
The clk-exynos5-subcmu driver uses override only for the purpose of
creating meaningful names for children devices (matching names of power
domains, e.g. DISP, MFC). The driver_override was not developed for
this purpose so just switch to default names of devices to fix the
issue.
Fixes: b06a532bf1fa ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
platform_device_alloc() failure
During initialization of subdevices if platform_device_alloc() failed,
returned NULL pointer will be later dereferenced. Add proper error
paths to exynos5_clk_register_subcmu(). The return value of this
function is still ignored because at this stage of init there is nothing
we can do.
Fixes: b06a532bf1fa ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This patch adds clocks required for the Exynos5433 SoC Slim Security
SubSystem (SlimSSS) IP block.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
[s.nawrocki@samsung.com: edited commit description]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Fix typo in sssx name, there should be three letters 's'.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This fixes typos in CLK_ACLK_IMEM_200 and CLK_ACLK_IMEM_266 clock definition,
leading to incorrect parent clock assignment.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
[s.nawrocki@samsung.com: edited commit description]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Fix spelling mistake: "lenght" -> "length"
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: e062b571777f ("clk: exynos4: register clocks using common clock framework")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This flag doesn't look to be used by any code, just set in the clk init
structure and then never tested again. Remove it from this drivers as it
doesn't provide any benefit.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
clk_notifier_register() documentation states, that the provided notifier
callbacks associated with the notifier must not re-enter into the clk
framework by calling any top-level clk APIs. Fix this by replacing
clk_get_rate() calls with clk_hw_get_rate(), which is safe in this
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Ensure that clocks for core SoC modules (including TZPC0..9 modules)
are enabled for suspend/resume cycle. This fixes suspend/resume
support on Exynos5422-based Odroid XU3/XU4 boards.
Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
The bit of GATE_BUS_PERIS1 for CLK_SECKEY is just reserved on
exynos5422/5800, not exynos5420. Define gate clk for exynos5420 to
handle the bit only on exynos5420.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[m.szyprow: rewrote commit subject]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
All sclk_uart clocks in TOP CMU have to be kept enabled for suspend/resume
cycle, otherwise TM2(e) boards hangs before entering the suspend mode.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Exynos4412 ISP clock are provided by separate Exynos4412 ISP clock
driver, so support for them in Exynos4-clk driver can be removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Before entering system suspend, one has to ensure that some clocks from
TOP, CPIF and PERIC CMUs are enabled. This is needed by the firmware
to properly perform system suspend operation. Instead of adding more and
more clocks with CRITICAL flag, simply enable those clocks directly in
respective CMU registers using 'suspend_regs' feature.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|