summaryrefslogtreecommitdiffstats
path: root/drivers/ata/sata_promise.c
AgeCommit message (Collapse)Author
2008-04-17libata: rename SFF port opsTejun Heo
Add sff_ prefix to SFF specific port ops. This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames ops and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: rename SFF functionsTejun Heo
SFF functions have confusing names. Some have sff prefix, some have bmdma, some std, some pci and some none. Unify the naming by... * SFF functions which are common to both BMDMA and non-BMDMA are prefixed with ata_sff_. * SFF functions which are specific to BMDMA are prefixed with ata_bmdma_. * SFF functions which are specific to PCI but apply to both BMDMA and non-BMDMA are prefixed with ata_pci_sff_. * SFF functions which are specific to PCI and BMDMA are prefixed with ata_pci_bmdma_. * Drop generic prefixes from LLD specific routines. For example, bfin_std_dev_select -> bfin_dev_select. The following renames are noteworthy. ata_qc_issue_prot() -> ata_sff_qc_issue() ata_pci_default_filter() -> ata_bmdma_mode_filter() ata_dev_try_classify() -> ata_sff_dev_classify() This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames functions and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata annotationsAl Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17libata: make reset related methods proper port operationsTejun Heo
Currently reset methods are not specified directly in the ata_port_operations table. If a LLD wants to use custom reset methods, it should construct and use a error_handler which uses those reset methods. It's done this way for two reasons. First, the ops table already contained too many methods and adding four more of them would noticeably increase the amount of necessary boilerplate code all over low level drivers. Second, as ->error_handler uses those reset methods, it can get confusing. ie. By overriding ->error_handler, those reset ops can be made useless making layering a bit hazy. Now that ops table uses inheritance, the first problem doesn't exist anymore. The second isn't completely solved but is relieved by providing default values - most drivers can just override what it has implemented and don't have to concern itself about higher level callbacks. In fact, there currently is no driver which actually modifies error handling behavior. Drivers which override ->error_handler just wraps the standard error handler only to prepare the controller for EH. I don't think making ops layering strict has any noticeable benefit. This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and their PMP counterparts propoer ops. Default ops are provided in the base ops tables and drivers are converted to override individual reset methods instead of creating custom error_handler. * ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs aren't accessible. sata_promise doesn't need to use separate error_handlers for PATA and SATA anymore. * softreset is broken for sata_inic162x and sata_sx4. As libata now always prefers hardreset, this doesn't really matter but the ops are forced to NULL using ATA_OP_NULL for documentation purpose. * pata_hpt374 needs to use different prereset for the first and second PCI functions. This used to be done by branching from hpt374_error_handler(). The proper way to do this is to use separate ops and port_info tables for each function. Converted. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: implement and use ops inheritanceTejun Heo
libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: implement and use SHT initializersTejun Heo
libata lets low level drivers build scsi_host_template and register it to the SCSI layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This patch implements SHT initializers which can be used to initialize all the boilerplate entries in a sht. Three variants of them are implemented - BASE, BMDMA and NCQ - for different types of drivers. Note that entries can be overriden by putting individual initializers after the helper macro. All sht tables are identical before and after this patch. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-24sata_promise: fix hardreset hotplug events, take 2Mikael Pettersson
A Promise SATA controller will signal hotplug events when a hard reset (COMRESET) is done on a port. These events aren't masked by the driver, and the unexpected interrupts will cause a sequence of failed reset attempts util libata's EH finally gives up. This has not been a common problem so far, but the pending libata hardreset-by-default changes makes it a critical issue. The solution is to disable hotplug events before a reset, and to reenable them afterwards. (Promise's driver does this too.) This patch adds SATA-specific versions of ->freeze() and ->thaw() that also disable and enable hotplug events. PATA ports continue to use the old versions of ->freeze() and ->thaw(). Accesses to the hotplug register must be serialised via host->lock. We rely on ap->lock == &ap->host->lock and that libata takes this lock before ->freeze() and ->thaw(). Document this requirement. The interrupt handler is adjusted so its hotplug register accesses are inside the region protected by host->lock. Tested on various chips (SATA300TX4, SATA300TX2plus, SATAII150TX4, FastTrack TX4000) with various combinations of SATA and PATA disks, with and without the pending hardreset-by-default changes. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Acked-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15ata: fix sparse warning in sata_promise.cHarvey Harrison
drivers/ata/sata_promise.c:546:15: warning: symbol 'len' shadows an earlier one drivers/ata/sata_promise.c:538:6: originally declared here len is set again immediately after the loop, so this is safe. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: convert to chained sgTejun Heo
libata used private sg iterator to handle padding sg. Now that sg can be chained, padding can be handled using standard sg ops. Convert to chained sg. * s/qc->__sg/qc->sg/ * s/qc->pad_sgent/qc->extra_sg[]/. Because chaining consumes one sg entry. There need to be two extra sg entries. The renaming is also for future addition of other extra sg entries. * Padding setup is moved into ata_sg_setup_extra() which is organized in a way that future addition of other extra sg entries is easy. * qc->orig_n_elem is unused and removed. * qc->n_elem now contains the number of sg entries that LLDs should map. qc->mapped_n_elem is added to carry the original number of mapped sgs for unmapping. * The last sg of the original sg list is used to chain to extra sg list. The original last sg is pointed to by qc->last_sg and the content is stored in qc->saved_last_sg. It's restored during ata_sg_clean(). * All sg walking code has been updated. Unnecessary assertions and checks for conditions the core layer already guarantees are removed. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: rename ATA_PROT_ATAPI_* to ATAPI_PROT_*Tejun Heo
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and ATA_PROT_ATAPI_* are inconsistent causing confusion. Rename them to ATAPI_PROT_* and make them consistent with ATA counterpart. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23sata_promise: make pdc_atapi_pkt() use values from qc->tfTejun Heo
Make pdc_atapi_pkt() use values from qc->tf instead of creating its own. This is to ease future ATAPI handling changes. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-03sata_promise: fix endianess bug in ASIC PRD bug workaroundMikael Pettersson
The original workaround for the Promise ASIC PRD bug contained an endianess bug which I failed to detect: the adjustment of the last PRD entry's length field applied host arithmetic to little-endian data, which is incorrect on big-endian machines. We have the length available in host-endian format, so do the adjustment on host-endian data and then convert and store it in the PRD entry's little-endian data field. Thanks to an anonymous reviewer for detecting this bug. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-30sata_promise: cleanupsMikael Pettersson
Minor sata_promise cleanups: - use C99 array initialisers in pdc_port_info[] - add myself in the file head's Maintained by note, since users don't always read the MAINTAINERS file - SG/PRD bug workaround warrants driver version bump Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> -- drivers/ata/sata_promise.c | 17 +++++++++-------- 1 files changed, 9 insertions(+), 8 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-30sata_promise: ASIC PRD table bug workaround, take 2Mikael Pettersson
Second-generation Promise SATA controllers have an ASIC bug which can trigger if the last PRD entry is larger than 164 bytes, resulting in intermittent errors and possible data corruption. Work around this by replacing calls to ata_qc_prep() with a private version that fills the PRD, checks the size of the last entry, and if necessary splits it to avoid the bug. Also reduce sg_tablesize by 1 to accommodate the new entry. Tested on the second-generation SATA300 TX4 and SATA300 TX2plus, and the first-generation PDC20378. Thanks to Alexander Sabourenkov for verifying the bug by studying the vendor driver, and for writing the initial patch upon which this one is based. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> -- Changes since previous version: * use new PDC_MAX_PRD constant to initialise sg_tablesize drivers/ata/sata_promise.c | 87 ++++++++++++++++++++++++++++++++++++++++++--- 1 files changed, 83 insertions(+), 4 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-29[libata] Address some checkpatch-spotted issuesJeff Garzik
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-12libata: implement and use ata_port_desc() to report port configurationTejun Heo
Currently, port configuration reporting has the following problems. * iomapped address is reported instead of raw address * report contains irrelevant fields or lacks necessary fields for non-SFF controllers. * host->irq/irq2 are there just for reporting and hacky. This patch implements and uses ata_port_desc() and ata_port_pbar_desc(). ata_port_desc() is almost identical to ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no locking requirement, can only be used during host initialization and " " is used as separator instead of ", ". ata_port_pbar_desc() is a helper to ease reporting of a PCI BAR or an offsetted address into it. LLD pushes whatever description it wants using the above two functions. The accumulated description is printed on host registration after "[S/P]ATA max MAX_XFERMODE ". SFF init helpers and ata_host_activate() automatically add descriptions for addresses and irq respectively, so only LLDs which isn't standard SFF need to add custom descriptions. In many cases, such controllers need to report different things anyway. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12[libata] Remove ->port_disable() hookJeff Garzik
It was always set to ata_port_disable(). Removed the hook, and replaced the very few ap->ops->port_disable() callsites with direct calls to ata_port_disable(). Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12[libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()Jeff Garzik
* ->irq_ack() is redundant to what the irq handler already performs... chk-status + irq-clear. Furthermore, it is only called in one place, when screaming-irq-debugging is enabled, so we don't want to bother with a hook just for that. * ata_dummy_irq_on() is only ever used in drivers that have no callpath reaching ->irq_on(). Remove .irq_on hook from those drivers, and the now-unused ata_dummy_irq_on() Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: linkify PHY-related functionsTejun Heo
Make the following PHY-related functions to deal with ata_link instead of ata_port. * sata_print_link_status() * sata_down_spd_limit() * ata_set_sata_spd_limit() and friends * sata_link_debounce/resume() * sata_scr_valid/read/write/write_flush() * ata_link_on/offline() This patch introduces no behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: introduce ata_linkTejun Heo
Introduce ata_link. It abstracts PHY and sits between ata_port and ata_device. This new level of abstraction is necessary to support SATA Port Multiplier, which basically adds a bunch of links (PHYs) to a ATA host port. Fields related to command execution, spd_limit and EH are per-link and thus moved to ata_link. This patch only defines the host link. Multiple link handling will be added later. Also, a lot of ap->link derefences are added but many of them will be removed as each part is converted to deal directly with ata_link instead of ata_port. This patch introduces no behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-31sata_promise: FastTrack TX4200 is a second-generation chipMikael Pettersson
This patch corrects sata_promise to classify FastTrack TX4200 (DID 3515/3519) as a second-generation chip. Promise's partial- source FT TX4200 driver confirms this classification. Treating it as a first-generation chip causes several problems: 1. Detection failures. This is a recent regression triggered by the hotplug-enabling changes in 2.6.23-rc1. 2. Various "failed to resume link for reset" warnings. This patch fixes <http://bugzilla.kernel.org/show_bug.cgi?id=8936>. Thanks to Stephen Ziemba for reporting the bug and for testing the fix. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Tested-by: Stephen Ziemba <sziemba@ecn.purdue.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: make ->scr_read/write callbacks return error codeTejun Heo
Convert ->scr_read/write callbacks to return error code to better indicate failure. This will help handling of SCR_NOTIFICATION. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-10sata_promise: SATA hotplug support, take 2Mikael Pettersson
This patch enables hotplugging of SATA devices in the sata_promise driver. It's been tested successfully on both first- and second-generation Promise SATA chips: SATA150 TX2plus, SATAII150 TX2plus, SATAII150 TX4, SATA300 TX2plus, and SATA300 TX4. The only quirk I've seen is that hotplugging (insertion) on the first-generation SATA150 TX2plus requires a lengthier EH sequence than on the second-generation chips. On the second-generation chips a simple soft reset seems to suffice, but on the first-generation chip there's a "port is slow to respond" after the initial soft reset, after which libata issues a hard reset, and then the device is recognised. The hotplug checks are high up in the interrupt handling path, not deep down in error_intr as in ahci/sata_sil24. That's because the chip doesn't signal hotplug status changes in the per-port status register: instead a global register contains hotplug control and status flags for all ports. I considered following the ahci/sata_sil24 structure, but that would have required non-trivial changes to the interrupt handling path, so I chose to keep the hotplug changes simple and unobtrusive. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> -- This patch depends on the "sata_promise: cleanups" patch. Changes since the previous version (posted June 19): - Correct pdc_interrupt() to increment 'handled' also in the hotplug case. This prevents IRQ_NONE from being returned when an interrupt only has hotplug events to handle, which could confuse the kernel's IRQ machinery. - Added testing on the SATAII150 TX4. drivers/ata/sata_promise.c | 41 ++++++++++++++++++++++++++++++++++++----- 1 files changed, 36 insertions(+), 5 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09[libata] Clean up driver udma_mask initializersJeff Garzik
* Use ATA_UDMA* * Remove FIXME notations that once served to remind us to verify that these were indeed the correct UDMA masks. They are. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09sata_promise: cleanupsMikael Pettersson
This patch applies some trivial cleanups to sata_promise: - repair whitespace damage - correct comment at board_2057x_pata definition - pull SATAII TX4 support code out to separate functions - rename ata_nr to ata_no for consistency with libata's port_no - remove some init-time debug printks (requested by Jeff) This patch should cause no behavioural changes, except for the removed printks. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> -- drivers/ata/sata_promise.c | 56 ++++++++++++++++++--------------------------- 1 files changed, 23 insertions(+), 33 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09[libata] drivers: remove 'void __iomem *' casts from pre-iomap daysJeff Garzik
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-08sata_promise: use TF interface for polling NODATA commandsTejun Heo
sata_promise uses two different command modes - packet and TF. Packet mode is intelligent low-overhead mode while TF is the same old taskfile interface. As with other advanced interface (ahci/sil24), ATA_TFLAG_POLLING has no effect in packet mode. However, PIO commands are issued using TF interface in polling mode, so pdc_interrupt() considers interrupts spurious if ATA_TFLAG_POLLING is set. This is broken for polling NODATA commands because command is issued using packet mode but the interrupt handler ignores it due to ATA_TFLAG_POLLING. Fix pdc_qc_issue_prot() such that ATA/ATAPI NODATA commands are issued using TF interface if ATA_TFLAG_POLLING is set. This patch fixes detection failure introduced by polling SETXFERMODE. Signed-off-by: Tejun Heo <htejun@gmail.com> Acked-by: Mikael Pettersson <mikpe@it.uu.se> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-24[libata] sata_promise: fix flags typoJeff Garzik
A stray comma makes all the difference. Change to '|' as these flags should be or'd together. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-09sata_promise: SATAII-150/300 TX4 port numbering fixMikael Pettersson
There is a known problem with sata_promise on SATAII-150/300 TX4 controller cards: it enumerates drives in an order that differs from the port numbers printed on the controller cards. However, Promise's BIOS and Linux driver both get the order right. I investigated Promise's Linux driver (v1.01.0.23), and found that it explicitly changes the mapping from logical port number to ATA engine MMIO address on the SATAII TX4 cards. It does this on all SATAII TX4 cards, without inspecting revision etc. The SATAII TX2plus cards continue to use the same mapping that was used for the first-generation chips. This patch updates sata_promise to use the new port number to ATA engine mapping on SATAII TX4 cards, which fixes the drive enumeration order problem on those cards. Tested on several 1st and 2nd generation TX2plus and TX4 chips. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-09sata_promise: fix another error decode regressionMikael Pettersson
The sata_promise error decode update changed pdc_host_intr() to return and not complete the qc after detecting an error. Unfortunately not completing the qc:s causes them to always time out on error, which is wrong and has nasty side-effects. This patch updates pdc_error_intr() to call ata_port_abort(), similar to ahci and sata_sil24. Doing this is important as it makes EH see the original error and not a bogus timeout. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28libata: convert drivers with combined SATA/PATA ports to new init modelTejun Heo
Convert sata_via and sata_promise to new init model. Both controllers can have combined configuration (SATA + PATA) and used twisted initialization method (modifying port in ->port_start) to overcome probe_ent limitations. This patch converts both drivers to new init model in which such configuration is natively supported. * promise: Combined pata port now uses separate port_info entry right after the sata counterpart entry. * promise: Controller configuration is discerned using ap->flags. This simplifies init path and makes it look more like other LLDs. * via: Both SATA and PATA ports in vt6421 are represented in their own port_info structure. Tested on PDC20375 (SATA150 TX2plus) [105a:3375] and PDC40775 (SATA 300 TX2plus) [105a:3d73]. Couldn't test via cuz my c3 won't boot the current kernel. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28libata: improve AC_ERR_DEV handling for ->post_internal_cmdTejun Heo
->post_internal_cmd is simplified EH for internal commands. Its primary mission is to stop the controller such that no rogue memory access or other activities occur after the internal command is released. It may provide error diagnostics by setting qc->err_mask but this hasn't been a requirement. To ignore SETXFER failure for CFA devices, libata needs to know whether a command was failed by the device or for any other reason. ie. internal command needs to get AC_ERR_DEV right. This patch makes the following changes to AC_ERR_DEV handling and ->post_internal_cmd semantics to accomodate this need and simplify callback implementation. 1. As long as the correct bits in the result TF registers are set, there is no need to set AC_ERR_DEV explicitly. libata EH core takes care of that for both normal and internal commands. 2. The only requirement for ->post_internal_cmd() is to put the controller into quiescent state. It needs not to set any err_mask. 3. ata_exec_internal_sg() performs minimal error analysis such that AC_ERR_DEV is automatically set as long as result_tf is filled correctly. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28sata_promise: fix error decode regressionMikael Pettersson
Promise ATA ports should always be reset by pdc_reset_port() when errors are detected, but the recent error reason decoding update to sata_promise replaced that reset with a freeze. This patch changes the error detection to do a reset again. This makes the error decoding update safer, as it now only adds error decoding without changing any other behaviour. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28sata_promise: decode and report error reasonsMikael Pettersson
This patch adds much needed error reason decoding and reporting to sata_promise. It's simplistic but should log all relevant error info the controller provides. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28sata_promise: separate SATA and PATA opsMikael Pettersson
This patch changes sata_promise so that the PATA ports on TX2plus chips are bound to the pdc_pata_ops structure. This means that operations called from the SATA ops structures don't need any SATA-vs-PATA tests any more. Instead, operations that depend on a port being SATA or PATA are separated into different procedures. * pdc_cable_type() is split into a PATA version and a SATA version * pdc_error_handler() is split into a PATA version and a SATA version, that both call a common version after setting up the `hardreset' function pointer * pdc_old_check_atapi_dma() is now only used for SATAI ports, so is renamed to pdc_old_sata_check_atapi_dma() and simplified * pdc_sata_scr_{read,write}() are now only used for SATA ports, so their is-not-SATA tests are removed * pdc_port_start() is split into three procedures: a wrapper which performs the ->ops adjustment on TX2plus PATA ports, a procedure with the common code, and a procedure with the SATA-specific code (this bit might be cleaned up by Tejun's new init model) Tested on 20619, 20575, and 20775 chips. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28sata_promise: add missing cable_detect hooksMikael Pettersson
The recent change which moved cable detection from pdc_pre_reset() to the new ->cable_detect hook only added the hook for SATAII chips, leaving SATAI chips and the 20619 without the hook. Fixed by this patch. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28sata_promise: Switch to cable method, clean up some bits as a resultAlan Cox
Signed-off-by: Alan Cox <number6@the-village.bc.nu> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-26[libata] bump versionsJeff Garzik
Bump versions based on changes submitted during 2.6.21 merge window. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-25sata_promise: simplify port setupMikael Pettersson
Each place in pdc_ata_init_one() that initialises a SATA port first calls pdc_ata_setup_port(), and then manually assigns the port's ->scr_addr. Simplify the code by extending pdc_ata_setup_port() to also handle scr_addr initialisation; for PATA ports we pass NULL as scr_addr. The initialisation of the PATA-only 20619 redundantly set up scr_addr for the ports. Remove this. Tested on 20619, 20575, and 20775 chips. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-25sata_promise: fix 20619 new EH merge errorMikael Pettersson
When I merged my 20619 new EH conversion with #libata-upstream I had to manually resolve a conflict, and inadvertently lost pdc_pata_ops' ->post_internal_cmd binding. Corrected by this patch. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-15sata_promise: new EH conversion for 20619 chips, take 2Mikael Pettersson
This patch updates the sata_promise driver to use new-style libata error handling for 20619 (TX4000) chips. sata_promise already uses new EH for the other chips it supports, so the patch is quite simple: * remove ->phy_reset and ->eng_timeout ops from pdc_pata_ops, and instead bind ->freeze, ->thaw, ->error_handler, and ->post_internal_cmd to existing new EH functions * drop ATA_FLAG_SRST from board_20619's flags * remove now unused pdc_pata_phy_reset() and pdc_eng_timeout() Tested on a TX4000 with both modern working disks and old/quirky disks. Also used a CD-RW drive to test reading and writing CDs. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-15sata_promise: fix missing PATA cable detectionMikael Pettersson
This patch fixes an oversight which caused sata_promise to not perform cable detection on the TX2plus chips' PATA ports. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-14[PATCH] remove many unneeded #includes of sched.hTim Schmielau
After Al Viro (finally) succeeded in removing the sched.h #include in module.h recently, it makes sense again to remove other superfluous sched.h includes. There are quite a lot of files which include it but don't actually need anything defined in there. Presumably these includes were once needed for macros that used to live in sched.h, but moved to other header files in the course of cleaning it up. To ease the pain, this time I did not fiddle with any header files and only removed #includes from .c-files, which tend to cause less trouble. Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha, arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig, allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all configs in arch/arm/configs on arm. I also checked that no new warnings were introduced by the patch (actually, some warnings are removed that were emitted by unnecessarily included header files). Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-09libata: add another IRQ calls (libata drivers)Akira Iguchi
This patch is against each libata driver. Two IRQ calls are added in ata_port_operations. - irq_on() is used to enable interrupts. - irq_ack() is used to acknowledge a device interrupt. In most drivers, ata_irq_on() and ata_irq_ack() are used for irq_on and irq_ack respectively. In some drivers (ex: ahci, sata_sil24) which cannot use them as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09libata: convert to iomapTejun Heo
Convert libata core layer and LLDs to use iomap. * managed iomap is used. Pointer to pcim_iomap_table() is cached at host->iomap and used through out LLDs. This basically replaces host->mmio_base. * if possible, pcim_iomap_regions() is used Most iomap operation conversions are taken from Jeff Garzik <jgarzik@pobox.com>'s iomap branch. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09libata: update libata LLDs to use devresTejun Heo
Update libata LLDs to use devres. Core layer is already converted to support managed LLDs. This patch simplifies initialization and fixes many resource related bugs in init failure and detach path. For example, all converted drivers now handle ata_device_add() failure gracefully without excessive resource rollback code. As most resources are released automatically on driver detach, many drivers don't need or can do with much simpler ->{port|host}_stop(). In general, stop callbacks are need iff port or host needs to be given commands to shut it down. Note that freezing is enough in many cases and ports are automatically frozen before being detached. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09sata_promise: kill qc->nsectTejun Heo
Merge order left qc->nsect usage in sata_promise dangling. Kill it. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09sata_promise: handle ATAPI_NODATA ourselvesMikael Pettersson
This patch extends sata_promise to handle ATAPI_NODATA commands internally. However, commands destined to ATA_DFLAG_CDB_INTR devices are excluded from this and continue to be returned to libata. Concrete changes: - pdc_atapi_dma_pkt() is renamed to pdc_atapi_pkt(), and is extended to set up correct headers for NODATA packets - pdc_qc_prep() calls pdc_atapi_pkt() for ATAPI_NODATA - pdc_host_intr() handles ATAPI_NODATA - pdc_qc_issue_prot() sends ATAPI_NODATA packets via the chip's packet mechanism, except for CDB_INTR devices Tested on first- and second-generation chips, SATAPI and PATAPI, with no observable regressions. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09sata_promise: issue ATAPI commands as normal packetsMikael Pettersson
This patch (against libata #upstream + the ATAPI cleanup patch) reimplements sata_promise's ATAPI support to format ATAPI DMA commands as normal packets, and to issue them via the hardware's normal packet machinery. It turns out that the only reason for issuing ATAPI DMA commands via the pdc_issue_atapi_pkt_cmd() procedure was to perform two interrupt-fiddling steps for ATA_DFLAG_CDB_INTR devices. But these steps aren't needed because sata_promise sets ATA_FLAG_PIO_POLLING, which disables DMA for those devices. The remaining steps can easily be done in ATA taskfile packets. Concrete changes: - pdc_atapi_dma_pkt() is extended to program all packet setup steps, and not just contain the CDB; the sequence of steps exactly mirrors what pdc_issue_atapi_pkt_cmd() did - pdc_atapi_dma_pkt() needed more parameters: simplify it by just passing 'qc' and having it extract the data it needs - pdc_issue_atai_pkt_cmd() and its two helper procedures pdc_wait_for_drq() and pdc_wait_on_busy() are removed Tested on first- and second-generation chips, SATAPI and PATAPI, with no observable regressions. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09sata_promise: ATAPI cleanupMikael Pettersson
Here's a cleanup for yesterday's sata_promise ATAPI patch: - add and use a symbolic constant for the altstatus register - check return status from ata_busy_wait() - add missing newline in a warning printk() - update comment in pdc_issue_atapi_pkt_cmd() to clarify that the maybe-wait-for-INT issue cannot occur in the current driver, but may occur if the driver starts issuing ATAPI non-DMA commands as PDC packets Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>