Age | Commit message (Collapse) | Author |
|
Using a mask to represent bus DMA constraints has a set of limitations.
The biggest one being it can only hold a power of two (minus one). The
DMA mapping code is already aware of this and treats dev->bus_dma_mask
as a limit. This quirk is already used by some architectures although
still rare.
With the introduction of the Raspberry Pi 4 we've found a new contender
for the use of bus DMA limits, as its PCIe bus can only address the
lower 3GB of memory (of a total of 4GB). This is impossible to represent
with a mask. To make things worse the device-tree code rounds non power
of two bus DMA limits to the next power of two, which is unacceptable in
this case.
In the light of this, rename dev->bus_dma_mask to dev->bus_dma_limit all
over the tree and treat it as such. Note that dev->bus_dma_limit should
contain the higher accessible DMA address.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The devices found behind this PCIe chip have unusual DMA mapping
constraints as there is an AMBA interconnect placed in between them and
the different PCI endpoints. The offset between physical memory
addresses and AMBA's view is provided by reading a PCI config register,
which is saved and used whenever DMA mapping is needed.
It turns out that this DMA setup can be represented by properly setting
'dma_pfn_offset', 'dma_bus_mask' and 'dma_mask' during the PCI device
enable fixup. And ultimately allows us to get rid of this device's
custom DMA functions.
Aside from the code deletion and DMA setup, sta2x11_pdev_to_mapping() is
moved to avoid warnings whenever CONFIG_PM is not enabled.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
After commit cf65a0f6f6ff ("dma-mapping: move all DMA mapping code to
kernel/dma") some of the files are referring to outdated information,
i.e. old file names of DMA mapping sources. Fix it here.
Note, the lines with "Glue code for..." have been removed completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While the dma-direct code is (relatively) clean and simple we actually
have to use the swiotlb ops for the mapping on many architectures due
to devices with addressing limits. Instead of keeping two
implementations around this commit allows the dma-direct
implementation to call the swiotlb bounce buffering functions and
thus share the guts of the mapping implementation. This also
simplified the dma-mapping setup on a few architectures where we
don't have to differenciate which implementation to use.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
|
|
Give the basic phys_to_dma() and dma_to_phys() helpers a __-prefix and add
the memory encryption mask to the non-prefixed versions. Use the
__-prefixed versions directly instead of clearing the mask again in
various places.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/20180319103826.12853-13-hch@lst.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The generic swiotlb DMA ops were based on the x86 ones and provide
equivalent functionality, so use them.
Also fix the sta2x11 case. For that SOC the DMA map ops need an
additional physical to DMA address translations. For swiotlb buffers
that is done throught the phys_to_dma helper, but the sta2x11_dma_ops
also added an additional translation on the return value from
x86_swiotlb_alloc_coherent, which is only correct if that functions
returns a direct allocation and not a swiotlb buffer. With the
generic swiotlb and DMA-direct code phys_to_dma is not always used
and the separate sta2x11_dma_ops can be replaced with a simple
bit that marks if the additional physical to DMA address translation
is needed.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/20180319103826.12853-5-hch@lst.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The generic DMA-direct (CONFIG_DMA_DIRECT_OPS=y) implementation is now
functionally equivalent to the x86 nommu dma_map implementation, so
switch over to using it.
That includes switching from using x86_dma_supported in various IOMMU
drivers to use dma_direct_supported instead, which provides the same
functionality.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/20180319103826.12853-4-hch@lst.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
phys_to_dma, dma_to_phys and dma_capable are helpers published by
architecture code for use of swiotlb and xen-swiotlb only. Drivers are
not supposed to use these directly, but use the DMA API instead.
Move these to a new asm/dma-direct.h helper, included by a
linux/dma-direct.h wrapper that provides the default linear mapping
unless the architecture wants to override it.
In the MIPS case the existing dma-coherent.h is reused for now as
untangling it will take a bit of work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
|
|
And instead wire it up as method for all the dma_map_ops instances.
Note that this also means the arch specific check will be fully instead
of partially applied in the AMD iommu driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Some but not all architectures provide set_dma_ops(). Move dma_ops
from struct dev_archdata into struct device such that it becomes
possible on all architectures to configure dma_ops per device.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Cc: x86@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Most dma_map_ops structures are never modified. Constify these
structures such that these can be write-protected. This patch
has been generated as follows:
git grep -l 'struct dma_map_ops' |
xargs -d\\n sed -i \
-e 's/struct dma_map_ops/const struct dma_map_ops/g' \
-e 's/const struct dma_map_ops {/struct dma_map_ops {/g' \
-e 's/^const struct dma_map_ops;$/struct dma_map_ops;/' \
-e 's/const const struct dma_map_ops /const struct dma_map_ops /g';
sed -i -e 's/const \(struct dma_map_ops intel_dma_ops\)/\1/' \
$(git grep -l 'struct dma_map_ops intel_dma_ops');
sed -i -e 's/const \(struct dma_map_ops dma_iommu_ops\)/\1/' \
$(git grep -l 'struct dma_map_ops' | grep ^arch/powerpc);
sed -i -e '/^struct vmd_dev {$/,/^};$/ s/const \(struct dma_map_ops[[:blank:]]dma_ops;\)/\1/' \
-e '/^static void vmd_setup_dma_ops/,/^}$/ s/const \(struct dma_map_ops \*dest\)/\1/' \
-e 's/const \(struct dma_map_ops \*dest = \&vmd->dma_ops\)/\1/' \
drivers/pci/host/*.c
sed -i -e '/^void __init pci_iommu_alloc(void)$/,/^}$/ s/dma_ops->/intel_dma_ops./' arch/ia64/kernel/pci-dma.c
sed -i -e 's/static const struct dma_map_ops sn_dma_ops/static struct dma_map_ops sn_dma_ops/' arch/ia64/sn/pci/pci_dma.c
sed -i -e 's/(const struct dma_map_ops \*)//' drivers/misc/mic/bus/vop_bus.c
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Cc: x86@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The DMA Contiguous Memory Allocator support on x86 is disabled when
swiotlb config option is enabled. So DMA CMA is always disabled on
x86_64 because swiotlb is always enabled. This attempts to support for
DMA CMA with enabling swiotlb config option.
The contiguous memory allocator on x86 is integrated in the function
dma_generic_alloc_coherent() which is .alloc callback in nommu_dma_ops
for dma_alloc_coherent().
x86_swiotlb_alloc_coherent() which is .alloc callback in swiotlb_dma_ops
tries to allocate with dma_generic_alloc_coherent() firstly and then
swiotlb_alloc_coherent() is called as a fallback.
The main part of supporting DMA CMA with swiotlb is that changing
x86_swiotlb_free_coherent() which is .free callback in swiotlb_dma_ops
for dma_free_coherent() so that it can distinguish memory allocated by
dma_generic_alloc_coherent() from one allocated by
swiotlb_alloc_coherent() and release it with dma_generic_free_coherent()
which can handle contiguous memory. This change requires making
is_swiotlb_buffer() global function.
This also needs to change .free callback in the dma_map_ops for amd_gart
and sta2x11, because these dma_ops are also using
dma_generic_alloc_coherent().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Don Dutile <ddutile@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The "ConneXt" sta2x11 I/O Hub is a bridge from PCIe to AMBA, and is
used as main chipset in some Atom boards. The set of peripherals it
exports live in an AMBA bus internal to the chip, so a custom
remapping of addresses is needed. This is implemented by fixup calls
for the PCI deivices, based on CONFIG_X86_DEV_DMA_OPS and
CONFIG_X86_DMA_REMAP .
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Link: http://lkml.kernel.org/r/ddca670ca8180e52d49b3fe642742ddd23ab2cb2.1333560789.git.rubini@gnudd.com
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|