Age | Commit message (Collapse) | Author |
|
We already allocate hardware TCE tables in multiple levels and skip
intermediate levels when we can, now it is a turn of the KVM TCE tables.
Thankfully these are allocated already in 2 levels.
This moves the table's last level allocation from the creating helper to
kvmppc_tce_put() and kvm_spapr_tce_fault(). Since such allocation cannot
be done in real mode, this creates a virtual mode version of
kvmppc_tce_put() which handles allocations.
This adds kvmppc_rm_ioba_validate() to do an additional test if
the consequent kvmppc_tce_put() needs a page which has not been allocated;
if this is the case, we bail out to virtual mode handlers.
The allocations are protected by a new mutex as kvm->lock is not suitable
for the task because the fault handler is called with the mmap_sem held
but kvmhv_setup_mmu() locks kvm->lock and mmap_sem in the reverse order.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
The kvmppc_tce_to_ua() helper is called from real and virtual modes
and it works fine as long as CONFIG_DEBUG_LOCKDEP is not enabled.
However if the lockdep debugging is on, the lockdep will most likely break
in kvm_memslots() because of srcu_dereference_check() so we need to use
PPC-own kvm_memslots_raw() which uses realmode safe
rcu_dereference_raw_notrace().
This creates a realmode copy of kvmppc_tce_to_ua() which replaces
kvm_memslots() with kvm_memslots_raw().
Since kvmppc_rm_tce_to_ua() becomes static and can only be used inside
HV KVM, this moves it earlier under CONFIG_KVM_BOOK3S_HV_POSSIBLE.
This moves truly virtual-mode kvmppc_tce_to_ua() to where it belongs and
drops the prmap parameter which was never used in the virtual mode.
Fixes: d3695aa4f452 ("KVM: PPC: Add support for multiple-TCE hcalls", 2016-02-15)
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
The powernv platform maintains 2 TCE tables for VFIO - a hardware TCE
table and a table with userspace addresses. These tables are radix trees,
we allocate indirect levels when they are written to. Since
the memory allocation is problematic in real mode, we have 2 accessors
to the entries:
- for virtual mode: it allocates the memory and it is always expected
to return non-NULL;
- fr real mode: it does not allocate and can return NULL.
Also, DMA windows can span to up to 55 bits of the address space and since
we never have this much RAM, such windows are sparse. However currently
the SPAPR TCE IOMMU driver walks through all TCEs to unpin DMA memory.
Since we maintain a userspace addresses table for VFIO which is a mirror
of the hardware table, we can use it to know which parts of the DMA
window have not been mapped and skip these so does this patch.
The bare metal systems do not have this problem as they use a bypass mode
of a PHB which maps RAM directly.
This helps a lot with sparse DMA windows, reducing the shutdown time from
about 3 minutes per 1 billion TCEs to a few seconds for 32GB sparse guest.
Just skipping the last level seems to be good enough.
As non-allocating accessor is used now in virtual mode as well, rename it
from IOMMU_TABLE_USERSPACE_ENTRY_RM (real mode) to _RO (read only).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
The kvmppc_gpa_to_ua() helper itself takes care of the permission
bits in the TCE and yet every single caller removes them.
This changes semantics of kvmppc_gpa_to_ua() so it takes TCEs
(which are GPAs + TCE permission bits) to make the callers simpler.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
At the moment if the PUT_TCE{_INDIRECT} handlers fail to update
the hardware tables, we print a warning once, clear the entry and
continue. This is so as at the time the assumption was that if
a VFIO device is hotplugged into the guest, and the userspace replays
virtual DMA mappings (i.e. TCEs) to the hardware tables and if this fails,
then there is nothing useful we can do about it.
However the assumption is not valid as these handlers are not called for
TCE replay (VFIO ioctl interface is used for that) and these handlers
are for new TCEs.
This returns an error to the guest if there is a request which cannot be
processed. By now the only possible failure must be H_TOO_HARD.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The userspace can request an arbitrary supported page size for a DMA
window and this works fine as long as the mapped memory is backed with
the pages of the same or bigger size; if this is not the case,
mm_iommu_ua_to_hpa{_rm}() fail and tables do not populated with
dangerously incorrect TCEs.
However since it is quite easy to misconfigure the KVM and we do not do
reverts to all changes made to TCE tables if an error happens in a middle,
we better do the acceptable page size validation before we even touch
the tables.
This enhances kvmppc_tce_validate() to check the hardware IOMMU page sizes
against the preregistered memory page sizes.
Since the new check uses real/virtual mode helpers, this renames
kvmppc_tce_validate() to kvmppc_rm_tce_validate() to handle the real mode
case and mirrors it for the virtual mode under the old name. The real
mode handler is not used for the virtual mode as:
1. it uses _lockless() list traversing primitives instead of RCU;
2. realmode's mm_iommu_ua_to_hpa_rm() uses vmalloc_to_phys() which
virtual mode does not have to use and since on POWER9+radix only virtual
mode handlers actually work, we do not want to slow down that path even
a bit.
This removes EXPORT_SYMBOL_GPL(kvmppc_tce_validate) as the validators
are static now.
From now on the attempts on mapping IOMMU pages bigger than allowed
will result in KVM exit.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[mpe: Fix KVM_HV=n build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We return H_TOO_HARD from TCE update handlers when we think that
the next handler (realmode -> virtual mode -> user mode) has a chance to
handle the request; H_HARDWARE/H_CLOSED otherwise.
This changes the handlers to return H_TOO_HARD on every error giving
the userspace an opportunity to handle any request or at least log
them all.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The KVM TCE handlers are written in a way so they fail when either
something went horribly wrong or the userspace did some obvious mistake
such as passing a misaligned address.
We are going to enhance the TCE checker to fail on attempts to map bigger
IOMMU page than the underlying pinned memory so let's valitate TCE
beforehand.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
At the moment the real mode handler of H_PUT_TCE calls iommu_tce_xchg_rm()
which in turn reads the old TCE and if it was a valid entry, marks
the physical page dirty if it was mapped for writing. Since it is in
real mode, realmode_pfn_to_page() is used instead of pfn_to_page()
to get the page struct. However SetPageDirty() itself reads the compound
page head and returns a virtual address for the head page struct and
setting dirty bit for that kills the system.
This adds additional dirty bit tracking into the MM/IOMMU API for use
in the real mode. Note that this does not change how VFIO and
KVM (in virtual mode) set this bit. The KVM (real mode) changes include:
- use the lowest bit of the cached host phys address to carry
the dirty bit;
- mark pages dirty when they are unpinned which happens when
the preregistered memory is released which always happens in virtual
mode;
- add mm_iommu_ua_mark_dirty_rm() helper to set delayed dirty bit;
- change iommu_tce_xchg_rm() to take the kvm struct for the mm to use
in the new mm_iommu_ua_mark_dirty_rm() helper;
- move iommu_tce_xchg_rm() to book3s_64_vio_hv.c (which is the only
caller anyway) to reduce the real mode KVM and IOMMU knowledge
across different subsystems.
This removes realmode_pfn_to_page() as it is not used anymore.
While we at it, remove some EXPORT_SYMBOL_GPL() as that code is for
the real mode only and modules cannot call it anyway.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Merge our fixes branch from the 4.18 cycle to resolve some minor
conflicts.
|
|
asm/tlbflush.h is only needed for:
- using functions xxx_flush_tlb_xxx()
- using MMU_NO_CONTEXT
- including asm-generic/pgtable.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Only include linux/stringify.h is files using __stringify()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
A VM which has:
- a DMA capable device passed through to it (eg. network card);
- running a malicious kernel that ignores H_PUT_TCE failure;
- capability of using IOMMU pages bigger that physical pages
can create an IOMMU mapping that exposes (for example) 16MB of
the host physical memory to the device when only 64K was allocated to the VM.
The remaining 16MB - 64K will be some other content of host memory, possibly
including pages of the VM, but also pages of host kernel memory, host
programs or other VMs.
The attacking VM does not control the location of the page it can map,
and is only allowed to map as many pages as it has pages of RAM.
We already have a check in drivers/vfio/vfio_iommu_spapr_tce.c that
an IOMMU page is contained in the physical page so the PCI hardware won't
get access to unassigned host memory; however this check is missing in
the KVM fastpath (H_PUT_TCE accelerated code). We were lucky so far and
did not hit this yet as the very first time when the mapping happens
we do not have tbl::it_userspace allocated yet and fall back to
the userspace which in turn calls VFIO IOMMU driver, this fails and
the guest does not retry,
This stores the smallest preregistered page size in the preregistered
region descriptor and changes the mm_iommu_xxx API to check this against
the IOMMU page size.
This calculates maximum page size as a minimum of the natural region
alignment and compound page size. For the page shift this uses the shift
returned by find_linux_pte() which indicates how the page is mapped to
the current userspace - if the page is huge and this is not a zero, then
it is a leaf pte and the page is mapped within the range.
Fixes: 121f80ba68f1 ("KVM: PPC: VFIO: Add in-kernel acceleration for VFIO")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
At the moment we allocate the entire TCE table, twice (hardware part and
userspace translation cache). This normally works as we normally have
contigous memory and the guest will map entire RAM for 64bit DMA.
However if we have sparse RAM (one example is a memory device), then
we will allocate TCEs which will never be used as the guest only maps
actual memory for DMA. If it is a single level TCE table, there is nothing
we can really do but if it a multilevel table, we can skip allocating
TCEs we know we won't need.
This adds ability to allocate only first level, saving memory.
This changes iommu_table::free() to avoid allocating of an extra level;
iommu_table::set() will do this when needed.
This adds @alloc parameter to iommu_table::exchange() to tell the callback
if it can allocate an extra level; the flag is set to "false" for
the realmode KVM handlers of H_PUT_TCE hcalls and the callback returns
H_TOO_HARD.
This still requires the entire table to be counted in mm::locked_vm.
To be conservative, this only does on-demand allocation when
the usespace cache table is requested which is the case of VFIO.
The example math for a system replicating a powernv setup with NVLink2
in a guest:
16GB RAM mapped at 0x0
128GB GPU RAM window (16GB of actual RAM) mapped at 0x244000000000
the table to cover that all with 64K pages takes:
(((0x244000000000 + 0x2000000000) >> 16)*8)>>20 = 4556MB
If we allocate only necessary TCE levels, we will only need:
(((0x400000000 + 0x400000000) >> 16)*8)>>20 = 4MB (plus some for indirect
levels).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We want to support sparse memory and therefore huge chunks of DMA windows
do not need to be mapped. If a DMA window big enough to require 2 or more
indirect levels, and a DMA window is used to map all RAM (which is
a default case for 64bit window), we can actually save some memory by
not allocation TCE for regions which we are not going to map anyway.
The hardware tables alreary support indirect levels but we also keep
host-physical-to-userspace translation array which is allocated by
vmalloc() and is a flat array which might use quite some memory.
This converts it_userspace from vmalloc'ed array to a multi level table.
As the format becomes platform dependend, this replaces the direct access
to it_usespace with a iommu_table_ops::useraddrptr hook which returns
a pointer to the userspace copy of a TCE; future extension will return
NULL if the level was not allocated.
This should not change non-KVM handling of TCE tables and it_userspace
will not be allocated for non-KVM tables.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We are going to reuse multilevel TCE code for the userspace copy of
the TCE table and since it is big endian, let's make the copy big endian
too.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Current regs are scattered at kvm_vcpu_arch structure and it will
be more neat to organize them into pt_regs structure.
Also it will enable reimplementation of MMIO emulation code with
analyse_instr() later.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
physical pages
At the moment we only support in the host the IOMMU page sizes which
the guest is aware of, which is 4KB/64KB/16MB. However P9 does not support
16MB IOMMU pages, 2MB and 1GB pages are supported instead. We can still
emulate bigger guest pages (for example 16MB) with smaller host pages
(4KB/64KB/2MB).
This allows the physical IOMMU pages to use a page size smaller or equal
than the guest visible IOMMU page size.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
The other TCE handlers use page shift from the guest visible TCE table
(described by kvmppc_spapr_tce_iommu_table) so let's make H_STUFF_TCE
handlers do the same thing.
This should cause no behavioral change now but soon we will allow
the iommu_table::it_page_shift being different from from the emulated
table page size so this will play a role.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Since commit fb1522e099f0 ("KVM: update to new mmu_notifier semantic
v2", 2017-08-31), the MMU notifier code in KVM no longer calls the
kvm_unmap_hva callback. This removes the PPC implementations of
kvm_unmap_hva().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Add newer helpers to make the function usage simpler. It is always
recommended to use find_current_mm_pte() for walking the page table.
If we cannot use find_current_mm_pte(), it should be documented why
the said usage of __find_linux_pte() is safe against a parallel THP
split.
For now we have KVM code using __find_linux_pte(). This is because kvm
code ends up calling __find_linux_pte() in real mode with MSR_EE=0 but
with PACA soft_enabled = 1. We may want to fix that later and make
sure we keep the MSR_EE and PACA soft_enabled in sync. When we do that
we can switch kvm to use find_linux_pte().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
POWER9 running a radix guest will take some hypervisor interrupts
without going to real mode (turning off the MMU). This means that
early hypercall handlers may now be called in virtual mode. Most of
the handlers work just fine in both modes, but there are some that
can crash the host if called in virtual mode, notably the TCE (IOMMU)
hypercalls H_PUT_TCE, H_STUFF_TCE and H_PUT_TCE_INDIRECT. These
already have both a real-mode and a virtual-mode version, so we
arrange for the real-mode version to return H_TOO_HARD for radix
guests, which will result in the virtual-mode version being called.
The other hypercall which is sensitive to the MMU mode is H_RANDOM.
It doesn't have a virtual-mode version, so this adds code to enable
it to be called in either mode.
An alternative solution was considered which would refuse to call any
of the early hypercall handlers when doing a virtual-mode exit from a
radix guest. However, the XICS-on-XIVE code depends on the XICS
hypercalls being handled early even for virtual-mode exits, because
the handlers need to be called before the XIVE vCPU state has been
pulled off the hardware. Therefore that solution would have become
quite invasive and complicated, and was rejected in favour of the
simpler, though less elegant, solution presented here.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
This allows the host kernel to handle H_PUT_TCE, H_PUT_TCE_INDIRECT
and H_STUFF_TCE requests targeted an IOMMU TCE table used for VFIO
without passing them to user space which saves time on switching
to user space and back.
This adds H_PUT_TCE/H_PUT_TCE_INDIRECT/H_STUFF_TCE handlers to KVM.
KVM tries to handle a TCE request in the real mode, if failed
it passes the request to the virtual mode to complete the operation.
If it a virtual mode handler fails, the request is passed to
the user space; this is not expected to happen though.
To avoid dealing with page use counters (which is tricky in real mode),
this only accelerates SPAPR TCE IOMMU v2 clients which are required
to pre-register the userspace memory. The very first TCE request will
be handled in the VFIO SPAPR TCE driver anyway as the userspace view
of the TCE table (iommu_table::it_userspace) is not allocated till
the very first mapping happens and we cannot call vmalloc in real mode.
If we fail to update a hardware IOMMU table unexpected reason, we just
clear it and move on as there is nothing really we can do about it -
for example, if we hot plug a VFIO device to a guest, existing TCE tables
will be mirrored automatically to the hardware and there is no interface
to report to the guest about possible failures.
This adds new attribute - KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE - to
the VFIO KVM device. It takes a VFIO group fd and SPAPR TCE table fd
and associates a physical IOMMU table with the SPAPR TCE table (which
is a guest view of the hardware IOMMU table). The iommu_table object
is cached and referenced so we do not have to look up for it in real mode.
This does not implement the UNSET counterpart as there is no use for it -
once the acceleration is enabled, the existing userspace won't
disable it unless a VFIO container is destroyed; this adds necessary
cleanup to the KVM_DEV_VFIO_GROUP_DEL handler.
This advertises the new KVM_CAP_SPAPR_TCE_VFIO capability to the user
space.
This adds real mode version of WARN_ON_ONCE() as the generic version
causes problems with rcu_sched. Since we testing what vmalloc_to_phys()
returns in the code, this also adds a check for already existing
vmalloc_to_phys() call in kvmppc_rm_h_put_tce_indirect().
This finally makes use of vfio_external_user_iommu_id() which was
introduced quite some time ago and was considered for removal.
Tests show that this patch increases transmission speed from 220MB/s
to 750..1020MB/s on 10Gb network (Chelsea CXGB3 10Gb ethernet card).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
This reworks helpers for checking TCE update parameters in way they
can be used in KVM.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
VFIO on sPAPR already implements guest memory pre-registration
when the entire guest RAM gets pinned. This can be used to translate
the physical address of a guest page containing the TCE list
from H_PUT_TCE_INDIRECT.
This makes use of the pre-registrered memory API to access TCE list
pages in order to avoid unnecessary locking on the KVM memory
reverse map as we know that all of guest memory is pinned and
we have a flat array mapping GPA to HPA which makes it simpler and
quicker to index into that array (even with looking up the
kernel page tables in vmalloc_to_phys) than it is to find the memslot,
lock the rmap entry, look up the user page tables, and unlock the rmap
entry. Note that the rmap pointer is initialized to NULL
where declared (not in this patch).
If a requested chunk of memory has not been preregistered, this will
fall back to non-preregistered case and lock rmap.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
The guest view TCE tables are per KVM anyway (not per VCPU) so pass kvm*
there. This will be used in the following patches where we will be
attaching VFIO containers to LIOBNs via ioctl() to KVM (rather than
to VCPU).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
This moves the prototypes for functions that are only called from
assembler code out of asm/asm-prototypes.h into asm/kvm_ppc.h.
The prototypes were added in commit ebe4535fbe7a ("KVM: PPC:
Book3S HV: sparse: prototypes for functions called from assembler",
2016-10-10), but given that the functions are KVM functions,
having them in a KVM header will be better for long-term
maintenance.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Drop duplicate header asm/iommu.h from book3s_64_vio_hv.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
A bunch of KVM functions are only called from assembler.
Give them prototypes in asm-prototypes.h
This reduces sparse warnings.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Upcoming in-kernel VFIO acceleration needs different handling in real
and virtual modes which makes it hard to support both modes in
the same handler.
This creates a copy of kvmppc_rm_h_stuff_tce and kvmppc_rm_h_put_tce
in addition to the existing kvmppc_rm_h_put_tce_indirect.
This also fixes linker breakage when only PR KVM was selected (leaving
HV KVM off): the kvmppc_h_put_tce/kvmppc_h_stuff_tce functions
would not compile at all and the linked would fail.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This was delayed a day or two by some build-breakage on old toolchains
which we've now fixed.
There's two PCI commits both acked by Bjorn.
There's one commit to mm/hugepage.c which is (co)authored by Kirill.
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul
Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh
Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy,
Cyril Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell
Currey, Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_*
helpers from Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/
relaxed variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas
Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs
from Wei Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell
Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev
Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter
values, display domain indices in sysfs, eliminate domain suffix in
event names, from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit
checksum optimizations, 86xx consolidation, e5500/e6500 cpu
hotplug, more fman and other dt bits, and minor fixes/cleanup"
* tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (179 commits)
powerpc: Fix unrecoverable SLB miss during restore_math()
powerpc/8xx: Fix do_mtspr_cpu6() build on older compilers
powerpc/rcpm: Fix build break when SMP=n
powerpc/book3e-64: Use hardcoded mttmr opcode
powerpc/fsl/dts: Add "jedec,spi-nor" flash compatible
powerpc/T104xRDB: add tdm riser card node to device tree
powerpc32: PAGE_EXEC required for inittext
powerpc/mpc85xx: Add pcsphy nodes to FManV3 device tree
powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)
powerpc/86xx: Introduce and use common dtsi
powerpc/86xx: Update device tree
powerpc/86xx: Move dts files to fsl directory
powerpc/86xx: Switch to kconfig fragments approach
powerpc/86xx: Update defconfigs
powerpc/86xx: Consolidate common platform code
powerpc32: Remove one insn in mulhdu
powerpc32: small optimisation in flush_icache_range()
powerpc: Simplify test in __dma_sync()
powerpc32: move xxxxx_dcache_range() functions inline
powerpc32: Remove clear_pages() and define clear_page() inline
...
|
|
No code changes.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This enables userspace view of TCE tables to start from non-zero offset
on a bus. This will be used for huge DMA windows.
This only changes the internal structure, the user interface needs to
change in order to use an offset.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
At the moment the kvmppc_spapr_tce_table struct can only describe
4GB windows and handle fixed size (4K) pages. Dynamic DMA windows
support more so these limits need to be extended.
This replaces window_size (in bytes, 4GB max) with page_shift (32bit)
and size (64bit, in pages).
This should cause no behavioural change as this is changing
the internal structures only - the user interface still only
allows one to create a 32-bit table with 4KiB pages at this stage.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This adds real and virtual mode handlers for the H_PUT_TCE_INDIRECT and
H_STUFF_TCE hypercalls for user space emulated devices such as IBMVIO
devices or emulated PCI. These calls allow adding multiple entries
(up to 512) into the TCE table in one call which saves time on
transition between kernel and user space.
The current implementation of kvmppc_h_stuff_tce() allows it to be
executed in both real and virtual modes so there is one helper.
The kvmppc_rm_h_put_tce_indirect() needs to translate the guest address
to the host address and since the translation is different, there are
2 helpers - one for each mode.
This implements the KVM_CAP_PPC_MULTITCE capability. When present,
the kernel will try handling H_PUT_TCE_INDIRECT and H_STUFF_TCE if these
are enabled by the userspace via KVM_CAP_PPC_ENABLE_HCALL.
If they can not be handled by the kernel, they are passed on to
the user space. The user space still has to have an implementation
for these.
Both HV and PR-syle KVM are supported.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Upcoming multi-tce support (H_PUT_TCE_INDIRECT/H_STUFF_TCE hypercalls)
will validate TCE (not to have unexpected bits) and IO address
(to be within the DMA window boundaries).
This introduces helpers to validate TCE and IO address. The helpers are
exported as they compile into vmlinux (to work in realmode) and will be
used later by KVM kernel module in virtual mode.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
SPAPR_TCE_SHIFT is used in few places only and since IOMMU_PAGE_SHIFT_4K
can be easily used instead, remove SPAPR_TCE_SHIFT.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
At the moment only spapr_tce_tables updates are protected against races
but not lookups. This fixes missing protection by using RCU for the list.
As lookups also happen in real mode, this uses
list_for_each_entry_lockless() (which is expected not to access any
vmalloc'd memory).
This converts release_spapr_tce_table() to a RCU scheduled handler.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This reworks the existing H_PUT_TCE/H_GET_TCE handlers to have following
patches applied nicer.
This moves the ioba boundaries check to a helper and adds a check for
least bits which have to be zeros.
The patch is pretty mechanical (only check for least ioba bits is added)
so no change in behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This introduces the H_GET_TCE hypervisor call, which is basically the
reverse of H_PUT_TCE, as defined in the Power Architecture Platform
Requirements (PAPR).
The hcall H_GET_TCE is required by the kdump kernel, which uses it to
retrieve TCEs set up by the previous (panicked) kernel.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Since the code in book3s_64_vio_hv.c is called from real mode with HV
KVM, and therefore has to be built into the main kernel binary, this
makes it always built-in rather than part of the KVM module. It gets
called from the KVM module by PR KVM, so this adds an EXPORT_SYMBOL_GPL().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
There is nothing in the code for emulating TCE tables in the kernel
that prevents it from working on "PR" KVM... other than ifdef's and
location of the code.
This and moves the bulk of the code there to a new file called
book3s_64_vio.c.
This speeds things up a bit on my G5.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[agraf: fix for hv kvm, 32bit, whitespace]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This improves I/O performance for guests using the PAPR
paravirtualization interface by making the H_PUT_TCE hcall faster, by
implementing it in real mode. H_PUT_TCE is used for updating virtual
IOMMU tables, and is used both for virtual I/O and for real I/O in the
PAPR interface.
Since this moves the IOMMU tables into the kernel, we define a new
KVM_CREATE_SPAPR_TCE ioctl to allow qemu to create the tables. The
ioctl returns a file descriptor which can be used to mmap the newly
created table. The qemu driver models use them in the same way as
userspace managed tables, but they can be updated directly by the
guest with a real-mode H_PUT_TCE implementation, reducing the number
of host/guest context switches during guest IO.
There are certain circumstances where it is useful for userland qemu
to write to the TCE table even if the kernel H_PUT_TCE path is used
most of the time. Specifically, allowing this will avoid awkwardness
when we need to reset the table. More importantly, we will in the
future need to write the table in order to restore its state after a
checkpoint resume or migration.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|