Age | Commit message (Collapse) | Author |
|
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fix from Arnd Bergmann:
"Add correct MAX_POSSIBLE_PHYSMEM_BITS setting to asm-generic.
This is a single bugfix for a bug that Stefan Agner found on 32-bit
Arm, but that exists on several other architectures"
* tag 'asm-generic-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: pgtable: define MAX_POSSIBLE_PHYSMEM_BITS where needed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of patches for devicetree files and Arm SoC specific
drivers:
- A fix for OP-TEE shared memory on non-SMP systems
- multiple code fixes for the OMAP platform, including one regression
for the CPSW network driver and a few runtime warning fixes
- Some DT patches for the Rockchip RK3399 platform, in particular
fixing the MMC device ordering that recently became
nondeterministic with async probe.
- Multiple DT fixes for the Tegra platform, including a regression
fix for suspend/resume on TX2
- A regression fix for a user-triggered fault in the NXP dpio driver
- A regression fix for a bug caused by an earlier bug fix in the
xilinx firmware driver
- Two more DTC warning fixes
- Sylvain Lemieux steps down as maintainer for the NXP LPC32xx
platform"
* tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
optee: add writeback to valid memory type
firmware: xilinx: Use hash-table for api feature check
firmware: xilinx: Fix SD DLL node reset issue
soc: fsl: dpio: Get the cpumask through cpumask_of(cpu)
ARM: dts: dra76x: m_can: fix order of clocks
bus: ti-sysc: suppress err msg for timers used as clockevent/source
MAINTAINERS: Remove myself as LPC32xx maintainers
arm64: dts: qcom: clear the warnings caused by empty dma-ranges
arm64: dts: broadcom: clear the warnings caused by empty dma-ranges
ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
arm64: dts: rockchip: Reorder LED triggers from mmc devices on rk3399-roc-pc.
arm64: dts: rockchip: Assign a fixed index to mmc devices on rk3399 boards.
arm64: dts: rockchip: Remove system-power-controller from pmic on Odroid Go Advance
arm64: dts: rockchip: fix NanoPi R2S GMAC clock name
ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for various issues noticed during the -rc cycle:
- Earlier omap4 cpuidle fix was incomplete and needs to use a
configured idle state instead
- Fix am4 cpsw driver compatible to avoid invalid resource error
for the legacy driver
- Two kconfig fixes for genpd support that we added for for v5.10
for proper location of the option and adding missing option
- Fix ti-sysc reset status checking on enabling modules to ignore
quirky modules with reset status only usable when the quirk is
activated during reset. Also fix bogus resetdone warning for
cpsw and modules with no sysst register reset status bit
- Suppress a ti-sysc warning for timers reserved as system timers
- Fix the ordering of clocks for dra7 m_can
* tag 'omap-for-v5.10/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra76x: m_can: fix order of clocks
bus: ti-sysc: suppress err msg for timers used as clockevent/source
ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
bus: ti-sysc: Fix bogus resetdone warning on enable for cpsw
bus: ti-sysc: Fix reset status check for modules with quirks
ARM: OMAP2+: Fix missing select PM_GENERIC_DOMAINS_OF
ARM: OMAP2+: Fix location for select PM_GENERIC_DOMAINS
Link: https://lore.kernel.org/r/pull-1606460270-864284@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Borislav Petkov:
"Forwarded EFI fixes from Ard Biesheuvel:
- fix memory leak in efivarfs driver
- fix HYP mode issue in 32-bit ARM version of the EFI stub when built
in Thumb2 mode
- avoid leaking EFI pgd pages on allocation failure"
* tag 'efi-urgent-for-v5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Free efi_pgd with free_pages()
efivarfs: fix memory leak in efivarfs_create()
efi/arm: set HSCTLR Thumb2 bit correctly for HVC calls from HYP
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the bosch,m_can.yaml bindings the first clock shall be the "hclk",
while the second clock "cclk".
This patch fixes the order accordingly.
Fixes: 0adbe832f21a ("ARM: dts: dra76x: Add MCAN node")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The DLCI driver (dlci.c) implements the Frame Relay protocol. However,
we already have another newer and better implementation of Frame Relay
provided by the HDLC_FR driver (hdlc_fr.c).
The DLCI driver's implementation of Frame Relay is used by only one
hardware driver in the kernel - the SDLA driver (sdla.c).
The SDLA driver provides Frame Relay support for the Sangoma S50x devices.
However, the vendor provides their own driver (along with their own
multi-WAN-protocol implementations including Frame Relay), called WANPIPE.
I believe most users of the hardware would use the vendor-provided WANPIPE
driver instead.
(The WANPIPE driver was even once in the kernel, but was deleted in
commit 8db60bcf3021 ("[WAN]: Remove broken and unmaintained Sangoma
drivers.") because the vendor no longer updated the in-kernel WANPIPE
driver.)
Cc: Mike McLagan <mike.mclagan@linux.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201114150921.685594-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Around one third of the fixes this time are for dts files that list
their ethernet controller as using 'phy-mode="rgmii"' but are changed
to 'phy-mode="rgmii-id"' now, because the PHY drivers (realtek,
ksz9031, dp83867, ...) now configure the internal delay based on that
when they used to stay on the hardware default.
The long story is archived at
https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/
I was trying to hold off on the bugfixes until there was a solution
that would avoid breaking all boards, but that does not seem to be
happening any time soon, so I am now sending the correct version of
the dts files to ensure that at least these machines can use their
network devices again.
The other changes this time are:
- Updating the MAINTAINER lists for Allwinner and Samsung SoCs
- Multiple i.MX8MN machines get updates for their CPU operating
points to match the data sheet
- A revert for a dts patch that caused a regression in USB support on
Odroid U3
- Two fixes for the AMD Tee driver, addressing a memory leak and
missing locking
- Mark the network subsystem on qoriq-fman3 as cache coherent for
correctness as better performance.
- Minor dts fixes elsewhere, addressing dtc warnings and similar
problems"
* tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: dts: exynos: revert "add input clock to CMU in Exynos4412 Odroid"
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM
ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor
ARM: dts: stm32: Define VIO regulator supply on DHCOM
ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2
ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
tee: amdtee: synchronize access to shm list
tee: amdtee: fix memory leak due to reset of global shm list
arm64: dts: agilex/stratix10: Fix qspi node compatible
ARM: dts: imx6q-prti6q: fix PHY address
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, round 4:
- Fix MDIO over clocking on vf610-zii-dev-rev-b board to get switch
device work reliably.
- Fix imx50-evk IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
- Fix voltage for 1.6GHz CPU operating point on i.MX8MM to match
hardware datasheet.
- Fix phy-mode for KSZ9031 PHY on imx6qdl-udoo board.
* tag 'imx-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
Link: https://lore.kernel.org/r/20201116090702.GM5849@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Stefan Agner reported a bug when using zsram on 32-bit Arm machines
with RAM above the 4GB address boundary:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = a27bd01c
[00000000] *pgd=236a0003, *pmd=1ffa64003
Internal error: Oops: 207 [#1] SMP ARM
Modules linked in: mdio_bcm_unimac(+) brcmfmac cfg80211 brcmutil raspberrypi_hwmon hci_uart crc32_arm_ce bcm2711_thermal phy_generic genet
CPU: 0 PID: 123 Comm: mkfs.ext4 Not tainted 5.9.6 #1
Hardware name: BCM2711
PC is at zs_map_object+0x94/0x338
LR is at zram_bvec_rw.constprop.0+0x330/0xa64
pc : [<c0602b38>] lr : [<c0bda6a0>] psr: 60000013
sp : e376bbe0 ip : 00000000 fp : c1e2921c
r10: 00000002 r9 : c1dda730 r8 : 00000000
r7 : e8ff7a00 r6 : 00000000 r5 : 02f9ffa0 r4 : e3710000
r3 : 000fdffe r2 : c1e0ce80 r1 : ebf979a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 30c5383d Table: 235c2a80 DAC: fffffffd
Process mkfs.ext4 (pid: 123, stack limit = 0x495a22e6)
Stack: (0xe376bbe0 to 0xe376c000)
As it turns out, zsram needs to know the maximum memory size, which
is defined in MAX_PHYSMEM_BITS when CONFIG_SPARSEMEM is set, or in
MAX_POSSIBLE_PHYSMEM_BITS on the x86 architecture.
The same problem will be hit on all 32-bit architectures that have a
physical address space larger than 4GB and happen to not enable sparsemem
and include asm/sparsemem.h from asm/pgtable.h.
After the initial discussion, I suggested just always defining
MAX_POSSIBLE_PHYSMEM_BITS whenever CONFIG_PHYS_ADDR_T_64BIT is
set, or provoking a build error otherwise. This addresses all
configurations that can currently have this runtime bug, but
leaves all other configurations unchanged.
I looked up the possible number of bits in source code and
datasheets, here is what I found:
- on ARC, CONFIG_ARC_HAS_PAE40 controls whether 32 or 40 bits are used
- on ARM, CONFIG_LPAE enables 40 bit addressing, without it we never
support more than 32 bits, even though supersections in theory allow
up to 40 bits as well.
- on MIPS, some MIPS32r1 or later chips support 36 bits, and MIPS32r5
XPA supports up to 60 bits in theory, but 40 bits are more than
anyone will ever ship
- On PowerPC, there are three different implementations of 36 bit
addressing, but 32-bit is used without CONFIG_PTE_64BIT
- On RISC-V, the normal page table format can support 34 bit
addressing. There is no highmem support on RISC-V, so anything
above 2GB is unused, but it might be useful to eventually support
CONFIG_ZRAM for high pages.
Fixes: 61989a80fb3a ("staging: zsmalloc: zsmalloc memory allocation library")
Fixes: 02390b87a945 ("mm/zsmalloc: Prepare to variable MAX_PHYSMEM_BITS")
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lore.kernel.org/linux-mm/bdfa44bf1c570b05d6c70898e2bbb0acf234ecdf.1604762181.git.stefan@agner.ch/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A set of fixes for perf:
- A set of commits which reduce the stack usage of various perf
event handling functions which allocated large data structs on
stack causing stack overflows in the worst case
- Use the proper mechanism for detecting soft interrupts in the
recursion protection
- Make the resursion protection simpler and more robust
- Simplify the scheduling of event groups to make the code more
robust and prepare for fixing the issues vs. scheduling of
exclusive event groups
- Prevent event multiplexing and rotation for exclusive event groups
- Correct the perf event attribute exclusive semantics to take
pinned events, e.g. the PMU watchdog, into account
- Make the anythread filtering conditional for Intel's generic PMU
counters as it is not longer guaranteed to be supported on newer
CPUs. Check the corresponding CPUID leaf to make sure
- Fixup a duplicate initialization in an array which was probably
caused by the usual 'copy & paste - forgot to edit' mishap"
* tag 'perf-urgent-2020-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Fix Add BW copypasta
perf/x86/intel: Make anythread filter support conditional
perf: Tweak perf_event_attr::exclusive semantics
perf: Fix event multiplexing for exclusive groups
perf: Simplify group_sched_in()
perf: Simplify group_sched_out()
perf/x86: Make dummy_iregs static
perf/arch: Remove perf_sample_data::regs_user_copy
perf: Optimize get_recursion_context()
perf: Fix get_recursion_context()
perf/x86: Reduce stack usage for x86_pmu::drain_pebs()
perf: Reduce stack usage of perf_output_begin()
|
|
Pull ARM fix from Russell King:
"Just one bug fix: avoid a fortify panic when copying optprobe template"
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9019/1: kprobes: Avoid fortify_panic() when copying optprobe template
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Mostly some fixes for a fallout in a PHY driver that pointed out errors
in our DTs. Along with that, Jernej agreed to be a reviewer!
* tag 'sunxi-fixes-for-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: OrangePi Prime: Fix ethernet node
arm64: dts: allwinner: a64: bananapi-m64: Enable RGMII RX/TX delay on PHY
arm64: dts: allwinner: h5: libretech-all-h5-cc: Enable RGMII RX/TX delay on PHY
ARM: dts: sunxi: bananapi-m2-plus: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun9i: Enable both RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun8i: a83t: Enable both RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun8i: h3: orangepi-plus2e: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun7i: bananapi-m1-plus: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun7i: cubietruck: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun6i: a31-hummingbird: Enable RGMII RX/TX delay on Ethernet PHY
Revert "arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high"
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix ethernet node
arm64: dts: allwinner: h5: OrangePi PC2: Fix ethernet node
arm64: dts: allwinner: a64: Pine64 Plus: Fix ethernet node
arm64: dts: allwinner: a64: OrangePi Win: Fix ethernet node
arm64: dts: allwinner: Pine H64: Enable both RGMII RX/TX delay
arm64: dts: allwinner: beelink-gs1: Enable both RGMII RX/TX delay
arm64: dts: allwinner: pinetab: Drop unnecessary address/size-cells information
MAINTAINERS: Add Jernej Škrabec as a reviewer for Allwinner SoCs support
Link: https://lore.kernel.org/r/d1a1a6a6-fca4-4f1b-93b3-f2f6963b4e04.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.10, round 2
Highlights:
-----------
-Fixes are for DHCOM/DHCOR boards:
- Fix TA3-GPIO-C button
- Fix LED5 mapping
- Define VIO regulator supply on DHCOM
- Enable thermal sensor support on stm32mp15xx-dhcor
- Keep VDDA LDO1 always on to avoid leakage
* tag 'stm32-dt-for-v5.10-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM
ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor
ARM: dts: stm32: Define VIO regulator supply on DHCOM
ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2
ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2
Link: https://lore.kernel.org/r/65bfc73d-aae1-5309-2e11-1e3da647ad46@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This reverts commit eaf2d2f6895d676dda6c95a652b58594f2887720.
The commit eaf2d2f6895d ("ARM: dts: exynos: add input clock to CMU in
Exynos4412 Odroid") breaks probing of usb3503 USB hub on Odroid U3.
It changes the order of clock drivers probe: the clkout (Exynos PMU)
driver is probed before the main clk-exynos4 driver. The clkout driver
on Exynos4412 depends on clk-exynos4 but it does not support deferred
probe, therefore this dependency and changed probe order causes probe
failure.
The usb3503 USB hub on Odroid U3 on the other hand requires clkout
clock. This can be seen in logs:
[ 5.007442] usb3503 0-0008: unable to request refclk (-517)
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200921174818.15525-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, 3rd round:
- A series from Krzysztof Kozlowski to fix missing PMIC's interrupt
line pull-up for i.MX8MM and i.MX8MN boards.
- Set Bluetooth chip max-speed to 4000000 on imx8mm-beacon-som board
to fix the choppy Bluetooth audio sound.
- Remove non-existent OTG2, usbphynop2, and the usbmisc2 from i.MX8MN
device tree.
- Fix the endianness setting of RCPM node on Layerscape SoCs.
- Add the missing dma-coherent property for qoriq-fman device to improve
the performance.
- Fix the Ethernet PHY address on imx6q-prti6q board.
* tag 'imx-fixes-5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6q-prti6q: fix PHY address
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mn-ddr4-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mn-var-som: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-beacon-som: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-var-som: fix missing PMIC's interrupt line pull-up
Link: https://lore.kernel.org/r/20201030151821.GA28266@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix compatible the new CPSW switchdev DT node to avoid probing of legacy
CPSW driver which fails:
[ 2.781009] cpsw 4a100000.switch: invalid resource
Fixes: 7bf8f37aea82 ("ARM: dts: am437x-l4: add dt node for new cpsw switchdev driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The SPI chip selects are represented as:
cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>, <&gpio4 13 GPIO_ACTIVE_LOW>;
, which means that they are used in GPIO function instead of native
SPI mode.
Fix the IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
Fixes: c605cbf5e135 ("ARM: dts: imx: add device tree support for Freescale imx50evk board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
struct perf_sample_data lives on-stack, we should be careful about it's
size. Furthermore, the pt_regs copy in there is only because x86_64 is a
trainwreck, solve it differently.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Link: https://lkml.kernel.org/r/20201030151955.258178461@infradead.org
|
|
The VDDA LDO1 PMIC output supplies the analog VDDA input of the
STM32MP1 on DHCOM, keep it always on, otherwise there could be
leakage through the SoC.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable STM32 Digital Thermal Sensor driver for stm32mp15xx-dhcor SoMs.
Fixes: 94cafe1b6482 ("ARM: dts: stm32: Add Avenger96 devicetree support based on STM32MP157A")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The VIO regulator is supplied by PMIC Buck3, describe this in the DT.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
On the prototype DHCOM, the LED5 was connected to pin PG2 of the
STM32MP15xx, however on the production SoM this was changed to pin
PC6. Update the connection in the DT.
Fixes: 81d5fc719798 ("ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
On the prototype DHCOM, the TA3-GPIO-C button was connected to pin PI11 of
the STM32MP15xx, however on the production SoM this was changed to pin PG0
to free up the IRQ line 11 for LAN8710i PHY IRQ. Update the connection in
the DT. Since the IRQ line 0 is used for PMIC as well and cannot be shared
with the button, make the button polled.
Fixes: 87cabf9405cb ("ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
free_highpages() iterates over the free memblock regions in high
memory, and marks each page as available for the memory management
system.
Until commit cddb5ddf2b76 ("arm, xtensa: simplify initialization of
high memory pages") it rounded beginning of each region upwards and end of
each region downwards.
However, after that commit free_highmem() rounds the beginning and end of
each region downwards, and we may end up freeing a page that is
memblock_reserve()d, resulting in memory corruption.
Restore the original rounding of the region boundaries to avoid freeing
reserved pages.
Fixes: cddb5ddf2b76 ("arm, xtensa: simplify initialization of high memory pages")
Link: https://lore.kernel.org/r/20201029110334.4118-1-ardb@kernel.org/
Link: https://lore.kernel.org/r/20201031094345.6984-1-rppt@kernel.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Co-developed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Due to bug in the bootloader, the PHY has floating address and may
randomly change on each PHY reset. To avoid it, the updated bootloader
with the following patch[0] should be used:
| ARM: protonic: disable on-die termination to fix PHY bootstrapping
|
| If on-die termination is enabled, the RXC pin of iMX6 will be pulled
| high. Since we already have an 10K pull-down on board, the RXC level on
| PHY reset will be ~800mV, which is mostly interpreted as 1. On some
| reboots we get 0 instead and kernel can't detect the PHY properly.
|
| Since the default 0x020e07ac value is 0, it is sufficient to remove this
| entry from the affected imxcfg files.
|
| Since we get stable 0 on pin PHYADDR[2], the PHY address is changed from
| 4 to 0.
With latest bootloader update, the PHY address will be fixed to "0".
[0] https://git.pengutronix.de/cgit/barebox/commit/?id=93f7dcf631edfcda19e7757b28d66017ea274b81
Fixes: 0d446a505592 ("ARM: dts: add Protonic PRTI6Q board")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The ZII devel B board has two generations of Marvell Switches. The
mv88e6352 supports an MDIO clock of 12MHz. However the older 88e6185
does not like 12MHz, and often fails to probe.
Reduce the clock speed to 5MHz, which seems to work reliably.
Cc: Chris Healy <cphealy@gmail.com>
Fixes: b955387667ec ("ARM: dts: ZII: update MDIO speed and preamble")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") fixed micrel phy driver adding proper support for phy
modes. Adapt imx6q-udoo board phy settings : explicitly set required
delay configuration using "rgmii-id".
Fixes: cbd54fe0b2bc ("ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo")
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a fairly large set of bug fixes on top of -rc1, as most of
them were ready but didn't quite make it into the last-minute pull
requests for the merge window.
Allwinner:
- fix for incorrect CPU overtemperature limit
Amlogic:
- multiple smaller DT bugfixes, and missing device nodes
Marvell EBU:
- add missing aliases for ethernet switch ports on espressobin board
Marvell MMP:
- DTC warning fix
- bugfix for camera interface power-down
NXP i.MX:
- re-enable the GPIO driver on all defconfigs
ST STM32MP1:
- fix random crashes from incorrect voltage settings
Synaptics Berlin:
- enable the correct hardware timer driver
Texas Instruments K2G:
- fix a boot regression in the power domain code
TEE drivers:
- fix regression in TEE "login" method
SCMI drivers:
- multiple code fixes for corner cases in newly added code
MAINTAINERS file:
- move Kukjin Kim and Sangbeom Kim to credits (used to work on
Samsung Exynos)
- Masahiro Yamada is stepping down as Uniphier maintainer
I did not include a series of patches that work around a regression
caused by a bugfix in an ethernet phy driver that resulted in an
inadvertent DT binding change. This is still under discussion"
* tag 'arm-soc-fixes-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
soc: ti: ti_sci_pm_domains: check for proper args count in xlate
ARM: dts: stm32: Describe Vin power supply on stm32mp157c-edx board
ARM: dts: stm32: Describe Vin power supply on stm32mp15xx-dkx board
ARM: multi_v5_defconfig: Select CONFIG_GPIO_MXC
ARM: imx_v4_v5_defconfig: Select CONFIG_GPIO_MXC
ARM: dts: mmp2-olpc-xo-1-75: Use plural form of "-gpios"
ARM: dts: mmp3: Add power domain for the camera
arm64: berlin: Select DW_APB_TIMER_OF
dt-bindings: sram: sunxi-sram: add V3s compatible string
MAINTAINERS: Move Sangbeom Kim to credits
MAINTAINERS: Move Kukjin Kim to credits
MAINTAINERS: step down as maintainer of UniPhier SoCs and Denali driver
ARM: multi_v7_defconfig: Build in CONFIG_GPIO_MXC by default
ARM: imx_v6_v7_defconfig: Build in CONFIG_GPIO_MXC by default
arm64: defconfig: Build in CONFIG_GPIO_MXC by default
arm64: dts: meson: odroid-n2 plus: fix vddcpu_a pwm
ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
arm64: dts: amlogic: add missing ethernet reset ID
firmware: arm_scmi: Fix duplicate workqueue name
firmware: arm_scmi: Fix locking in notifications
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.10, round 1
Highlights:
-----------
-On STM32MP157 DK & ED boards: Add Vin supply description to avoid
random kernel crash due to vref_ddr regulator issue.
* tag 'stm32-dt-for-v5.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Describe Vin power supply on stm32mp157c-edx board
ARM: dts: stm32: Describe Vin power supply on stm32mp15xx-dkx board
Link: https://lore.kernel.org/r/4ac236b3-b980-f653-f644-53e586570724@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add description for Vin power supply and for peripherals that
are supplied by Vin.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add description for Vin power supply and for peripherals that
are supplied by Vin.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
After turning on warnings for orphan section placement, enabling
CONFIG_UNWINDER_FRAME_POINTER instead of CONFIG_UNWINDER_ARM causes
thousands of warnings when clang + ld.lld are used:
$ scripts/config --file arch/arm/configs/multi_v7_defconfig \
-d CONFIG_UNWINDER_ARM \
-e CONFIG_UNWINDER_FRAME_POINTER
$ make -skj"$(nproc)" ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- LLVM=1 defconfig zImage
ld.lld: warning: init/built-in.a(main.o):(.ARM.extab) is being placed in '.ARM.extab'
ld.lld: warning: init/built-in.a(main.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(main.o):(.ARM.extab.ref.text) is being placed in '.ARM.extab.ref.text'
ld.lld: warning: init/built-in.a(do_mounts.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(do_mounts.o):(.ARM.extab) is being placed in '.ARM.extab'
ld.lld: warning: init/built-in.a(do_mounts_rd.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(do_mounts_rd.o):(.ARM.extab) is being placed in '.ARM.extab'
ld.lld: warning: init/built-in.a(do_mounts_initrd.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(initramfs.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(initramfs.o):(.ARM.extab) is being placed in '.ARM.extab'
ld.lld: warning: init/built-in.a(calibrate.o):(.ARM.extab.init.text) is being placed in '.ARM.extab.init.text'
ld.lld: warning: init/built-in.a(calibrate.o):(.ARM.extab) is being placed in '.ARM.extab'
These sections are handled by the ARM_UNWIND_SECTIONS define, which is
only added to the list of sections when CONFIG_ARM_UNWIND is set.
CONFIG_ARM_UNWIND is a hidden symbol that is only selected when
CONFIG_UNWINDER_ARM is set so CONFIG_UNWINDER_FRAME_POINTER never
handles these sections. According to the help text of
CONFIG_UNWINDER_ARM, these sections should be discarded so that the
kernel image size is not affected.
Fixes: 5a17850e251a ("arm/build: Warn on orphan section placement")
Link: https://github.com/ClangBuiltLinux/linux/issues/1152
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Review-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
[kees: Made the discard slightly more specific]
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200928224854.3224862-1-natechancellor@gmail.com
|
|
Setting both CONFIG_KPROBES=y and CONFIG_FORTIFY_SOURCE=y on ARM leads
to a panic in memcpy() when injecting a kprobe despite the fixes found
in commit e46daee53bb5 ("ARM: 8806/1: kprobes: Fix false positive with
FORTIFY_SOURCE") and commit 0ac569bf6a79 ("ARM: 8834/1: Fix: kprobes:
optimized kprobes illegal instruction").
arch/arm/include/asm/kprobes.h effectively declares
the target type of the optprobe_template_entry assembly label as a u32
which leads memcpy()'s __builtin_object_size() call to determine that
the pointed-to object is of size four. However, the symbol is used as a handle
for the optimised probe assembly template that is at least 96 bytes in size.
The symbol's use despite its type blows up the memcpy() in ARM's
arch_prepare_optimized_kprobe() with a false-positive fortify_panic() when it
should instead copy the optimised probe template into place:
```
$ sudo perf probe -a aspeed_g6_pinctrl_probe
[ 158.457252] detected buffer overflow in memcpy
[ 158.458069] ------------[ cut here ]------------
[ 158.458283] kernel BUG at lib/string.c:1153!
[ 158.458436] Internal error: Oops - BUG: 0 [#1] SMP ARM
[ 158.458768] Modules linked in:
[ 158.459043] CPU: 1 PID: 99 Comm: perf Not tainted 5.9.0-rc7-00038-gc53ebf8167e9 #158
[ 158.459296] Hardware name: Generic DT based system
[ 158.459529] PC is at fortify_panic+0x18/0x20
[ 158.459658] LR is at __irq_work_queue_local+0x3c/0x74
[ 158.459831] pc : [<8047451c>] lr : [<8020ecd4>] psr: 60000013
[ 158.460032] sp : be2d1d50 ip : be2d1c58 fp : be2d1d5c
[ 158.460174] r10: 00000006 r9 : 00000000 r8 : 00000060
[ 158.460348] r7 : 8011e434 r6 : b9e0b800 r5 : 7f000000 r4 : b9fe4f0c
[ 158.460557] r3 : 80c04cc8 r2 : 00000000 r1 : be7c03cc r0 : 00000022
[ 158.460801] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 158.461037] Control: 10c5387d Table: b9cd806a DAC: 00000051
[ 158.461251] Process perf (pid: 99, stack limit = 0x81c71a69)
[ 158.461472] Stack: (0xbe2d1d50 to 0xbe2d2000)
[ 158.461757] 1d40: be2d1d84 be2d1d60 8011e724 80474510
[ 158.462104] 1d60: b9e0b800 b9fe4f0c 00000000 b9fe4f14 80c8ec80 be235000 be2d1d9c be2d1d88
[ 158.462436] 1d80: 801cee44 8011e57c b9fe4f0c 00000000 be2d1dc4 be2d1da0 801d0ad0 801cedec
[ 158.462742] 1da0: 00000000 00000000 b9fe4f00 ffffffea 00000000 be235000 be2d1de4 be2d1dc8
[ 158.463087] 1dc0: 80204604 801d0738 00000000 00000000 b9fe4004 ffffffea be2d1e94 be2d1de8
[ 158.463428] 1de0: 80205434 80204570 00385c00 00000000 00000000 00000000 be2d1e14 be2d1e08
[ 158.463880] 1e00: 802ba014 b9fe4f00 b9e718c0 b9fe4f84 b9e71ec8 be2d1e24 00000000 00385c00
[ 158.464365] 1e20: 00000000 626f7270 00000065 802b905c be2d1e94 0000002e 00000000 802b9914
[ 158.464829] 1e40: be2d1e84 be2d1e50 802b9914 8028ff78 804629d0 b9e71ec0 0000002e b9e71ec0
[ 158.465141] 1e60: be2d1ea8 80c04cc8 00000cc0 b9e713c4 00000002 80205834 80205834 0000002e
[ 158.465488] 1e80: be235000 be235000 be2d1ea4 be2d1e98 80205854 80204e94 be2d1ecc be2d1ea8
[ 158.465806] 1ea0: 801ee4a0 80205840 00000002 80c04cc8 00000000 0000002e 0000002e 00000000
[ 158.466110] 1ec0: be2d1f0c be2d1ed0 801ee5c8 801ee428 00000000 be2d0000 006b1fd0 00000051
[ 158.466398] 1ee0: 00000000 b9eedf00 0000002e 80204410 006b1fd0 be2d1f60 00000000 00000004
[ 158.466763] 1f00: be2d1f24 be2d1f10 8020442c 801ee4c4 80205834 802c613c be2d1f5c be2d1f28
[ 158.467102] 1f20: 802c60ac 8020441c be2d1fac be2d1f38 8010c764 802e9888 be2d1f5c b9eedf00
[ 158.467447] 1f40: b9eedf00 006b1fd0 0000002e 00000000 be2d1f94 be2d1f60 802c634c 802c5fec
[ 158.467812] 1f60: 00000000 00000000 00000000 80c04cc8 006b1fd0 00000003 76f7a610 00000004
[ 158.468155] 1f80: 80100284 be2d0000 be2d1fa4 be2d1f98 802c63ec 802c62e8 00000000 be2d1fa8
[ 158.468508] 1fa0: 80100080 802c63e0 006b1fd0 00000003 00000003 006b1fd0 0000002e 00000000
[ 158.468858] 1fc0: 006b1fd0 00000003 76f7a610 00000004 006b1fb0 0026d348 00000017 7ef2738c
[ 158.469202] 1fe0: 76f3431c 7ef272d8 0014ec50 76f34338 60000010 00000003 00000000 00000000
[ 158.469461] Backtrace:
[ 158.469683] [<80474504>] (fortify_panic) from [<8011e724>] (arch_prepare_optimized_kprobe+0x1b4/0x1f8)
[ 158.470021] [<8011e570>] (arch_prepare_optimized_kprobe) from [<801cee44>] (alloc_aggr_kprobe+0x64/0x70)
[ 158.470287] r9:be235000 r8:80c8ec80 r7:b9fe4f14 r6:00000000 r5:b9fe4f0c r4:b9e0b800
[ 158.470478] [<801cede0>] (alloc_aggr_kprobe) from [<801d0ad0>] (register_kprobe+0x3a4/0x5a0)
[ 158.470685] r5:00000000 r4:b9fe4f0c
[ 158.470790] [<801d072c>] (register_kprobe) from [<80204604>] (__register_trace_kprobe+0xa0/0xa4)
[ 158.471001] r9:be235000 r8:00000000 r7:ffffffea r6:b9fe4f00 r5:00000000 r4:00000000
[ 158.471188] [<80204564>] (__register_trace_kprobe) from [<80205434>] (trace_kprobe_create+0x5ac/0x9ac)
[ 158.471408] r7:ffffffea r6:b9fe4004 r5:00000000 r4:00000000
[ 158.471553] [<80204e88>] (trace_kprobe_create) from [<80205854>] (create_or_delete_trace_kprobe+0x20/0x3c)
[ 158.471766] r10:be235000 r9:be235000 r8:0000002e r7:80205834 r6:80205834 r5:00000002
[ 158.471949] r4:b9e713c4
[ 158.472027] [<80205834>] (create_or_delete_trace_kprobe) from [<801ee4a0>] (trace_run_command+0x84/0x9c)
[ 158.472255] [<801ee41c>] (trace_run_command) from [<801ee5c8>] (trace_parse_run_command+0x110/0x1f8)
[ 158.472471] r6:00000000 r5:0000002e r4:0000002e
[ 158.472594] [<801ee4b8>] (trace_parse_run_command) from [<8020442c>] (probes_write+0x1c/0x28)
[ 158.472800] r10:00000004 r9:00000000 r8:be2d1f60 r7:006b1fd0 r6:80204410 r5:0000002e
[ 158.472968] r4:b9eedf00
[ 158.473046] [<80204410>] (probes_write) from [<802c60ac>] (vfs_write+0xcc/0x1e8)
[ 158.473226] [<802c5fe0>] (vfs_write) from [<802c634c>] (ksys_write+0x70/0xf8)
[ 158.473400] r8:00000000 r7:0000002e r6:006b1fd0 r5:b9eedf00 r4:b9eedf00
[ 158.473567] [<802c62dc>] (ksys_write) from [<802c63ec>] (sys_write+0x18/0x1c)
[ 158.473745] r9:be2d0000 r8:80100284 r7:00000004 r6:76f7a610 r5:00000003 r4:006b1fd0
[ 158.473932] [<802c63d4>] (sys_write) from [<80100080>] (ret_fast_syscall+0x0/0x54)
[ 158.474126] Exception stack(0xbe2d1fa8 to 0xbe2d1ff0)
[ 158.474305] 1fa0: 006b1fd0 00000003 00000003 006b1fd0 0000002e 00000000
[ 158.474573] 1fc0: 006b1fd0 00000003 76f7a610 00000004 006b1fb0 0026d348 00000017 7ef2738c
[ 158.474811] 1fe0: 76f3431c 7ef272d8 0014ec50 76f34338
[ 158.475171] Code: e24cb004 e1a01000 e59f0004 ebf40dd3 (e7f001f2)
[ 158.475847] ---[ end trace 55a5b31c08a29f00 ]---
[ 158.476088] Kernel panic - not syncing: Fatal exception
[ 158.476375] CPU0: stopping
[ 158.476709] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G D 5.9.0-rc7-00038-gc53ebf8167e9 #158
[ 158.477176] Hardware name: Generic DT based system
[ 158.477411] Backtrace:
[ 158.477604] [<8010dd28>] (dump_backtrace) from [<8010dfd4>] (show_stack+0x20/0x24)
[ 158.477990] r7:00000000 r6:60000193 r5:00000000 r4:80c2f634
[ 158.478323] [<8010dfb4>] (show_stack) from [<8046390c>] (dump_stack+0xcc/0xe8)
[ 158.478686] [<80463840>] (dump_stack) from [<80110750>] (handle_IPI+0x334/0x3a0)
[ 158.479063] r7:00000000 r6:00000004 r5:80b65cc8 r4:80c78278
[ 158.479352] [<8011041c>] (handle_IPI) from [<801013f8>] (gic_handle_irq+0x88/0x94)
[ 158.479757] r10:10c5387d r9:80c01ed8 r8:00000000 r7:c0802000 r6:80c0537c r5:000003ff
[ 158.480146] r4:c080200c r3:fffffff4
[ 158.480364] [<80101370>] (gic_handle_irq) from [<80100b6c>] (__irq_svc+0x6c/0x90)
[ 158.480748] Exception stack(0x80c01ed8 to 0x80c01f20)
[ 158.481031] 1ec0: 000128bc 00000000
[ 158.481499] 1ee0: be7b8174 8011d3a0 80c00000 00000000 80c04cec 80c04d28 80c5d7c2 80a026d4
[ 158.482091] 1f00: 10c5387d 80c01f34 80c01f38 80c01f28 80109554 80109558 60000013 ffffffff
[ 158.482621] r9:80c00000 r8:80c5d7c2 r7:80c01f0c r6:ffffffff r5:60000013 r4:80109558
[ 158.482983] [<80109518>] (arch_cpu_idle) from [<80818780>] (default_idle_call+0x38/0x120)
[ 158.483360] [<80818748>] (default_idle_call) from [<801585a8>] (do_idle+0xd4/0x158)
[ 158.483945] r5:00000000 r4:80c00000
[ 158.484237] [<801584d4>] (do_idle) from [<801588f4>] (cpu_startup_entry+0x28/0x2c)
[ 158.484784] r9:80c78000 r8:00000000 r7:80c78000 r6:80c78040 r5:80c04cc0 r4:000000d6
[ 158.485328] [<801588cc>] (cpu_startup_entry) from [<80810a78>] (rest_init+0x9c/0xbc)
[ 158.485930] [<808109dc>] (rest_init) from [<80b00ae4>] (arch_call_rest_init+0x18/0x1c)
[ 158.486503] r5:80c04cc0 r4:00000001
[ 158.486857] [<80b00acc>] (arch_call_rest_init) from [<80b00fcc>] (start_kernel+0x46c/0x548)
[ 158.487589] [<80b00b60>] (start_kernel) from [<00000000>] (0x0)
```
Fixes: e46daee53bb5 ("ARM: 8806/1: kprobes: Fix false positive with FORTIFY_SOURCE")
Fixes: 0ac569bf6a79 ("ARM: 8834/1: Fix: kprobes: optimized kprobes illegal instruction")
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Luka Oreskovic <luka.oreskovic@sartura.hr>
Tested-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Luka Oreskovic <luka.oreskovic@sartura.hr>
Cc: Juraj Vijtiuk <juraj.vijtiuk@sartura.hr>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, 2nd round:
A couple of more defconfig fixes to enable CONFIG_GPIO_MXC option for
i.MX ARMv4/v5 devices.
* tag 'imx-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: multi_v5_defconfig: Select CONFIG_GPIO_MXC
ARM: imx_v4_v5_defconfig: Select CONFIG_GPIO_MXC
Link: https://lore.kernel.org/r/20201026235230.GL9880@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Based on more testing, commit 8ca5ee624b4c ("ARM: OMAP2+: Restore MPU
power domain if cpu_cluster_pm_enter() fails") is a poor fix for handling
cpu_cluster_pm_enter() returned errors.
We should not override the cpuidle states with a hardcoded PWRDM_POWER_ON
value. Instead, we should use a configured idle state that does not cause
the context to be lost. Otherwise we end up configuring a potentially
improper state for the MPUSS. We also want to update the returned state
index for the selected state.
Let's just select the highest power idle state C1 to ensure no context
loss is allowed on cpu_cluster_pm_enter() errors. With these changes we
can now unconditionally call omap4_enter_lowpower() for WFI like we did
earlier before commit 55be2f50336f ("ARM: OMAP2+: Handle errors for
cpu_pm"). And we can return the selected state index.
Fixes: 8f04aea048d5 ("ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails")
Fixes: 55be2f50336f ("ARM: OMAP2+: Handle errors for cpu_pm")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since commit 12d16b397ce0 ("gpio: mxc: Support module build") the
CONFIG_GPIO_MXC option needs to be explicitly selected.
Select it to avoid boot issues on imx25/imx27 due to the lack of the
GPIO driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit 12d16b397ce0 ("gpio: mxc: Support module build") the
CONFIG_GPIO_MXC option needs to be explicitly selected.
Select it to avoid boot issues on imx25/imx27 due to the lack of the
GPIO driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10:
With commit 12d16b397ce0 ("gpio: mxc: Support module build") in place,
GPIO_MXC has no 'def_bool y' anymore, and needs to be enabled by
defconfig. It updates the defconfig files to explicitly enable the
option for fixing boot failure on i.MX platform.
* tag 'imx-fixes-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: multi_v7_defconfig: Build in CONFIG_GPIO_MXC by default
ARM: imx_v6_v7_defconfig: Build in CONFIG_GPIO_MXC by default
arm64: defconfig: Build in CONFIG_GPIO_MXC by default
Link: https://lore.kernel.org/r/20201026135601.GA32675@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The Ethernet PHY on the Bananapi M2+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl821 |