| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT changes for 5.4
Our usual pile of patches for the next release, which include mostly:
- More fixes thanks to the DT validation using the YAML bindings
- IR receiver support on the H6
- SPDIF support on the H6
- I2C Support on the H6
- CSI support on the A20
- RTC support on the H6
- New Boards: Lichee Zero Plus, Tanix TX6, A64-Olinuxino-eMMC
* tag 'sunxi-dt-for-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (40 commits)
arm64: dts: allwinner: orange-pi-3: Enable WiFi
ARM: dts: sunxi: Add missing watchdog clocks
ARM: dts: sunxi: Add missing watchdog interrupts
arm64: dts: allwinner: h6: Add support for RTC and fix the clock tree
ARM: dts: sun7i: Add CSI0 controller
arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)
dt-bindings: arm: sunxi: Add compatible for A64 OlinuXino with eMMC
ARM: dts: v3s: Change the timers compatible
ARM: dts: h3: Change the timers compatible
ARM: dts: a83t: Change the timers compatible
ARM: dts: a23/a33: Change the timers compatible
ARM: dts: sun6i: Add missing timers interrupts
ARM: dts: sun5i: Add missing timers interrupts
ARM: dts: sun4i: Add missing timers interrupts
dt-bindings: mfd: Convert Allwinner GPADC bindings to a schema
arm64: dts: allwinner: h6: Introduce Tanix TX6 board
dt-bindings: arm: sunxi: Add compatible for Tanix TX6 board
arm64: allwinner: h6: add I2C nodes
dt-bindings: i2c: mv64xxx: Add compatible for the H6 i2c node.
ARM: dts: sunxi: Add mdio bus sub-node to GMAC
...
Link: https://lore.kernel.org/r/d97e6252-9dd7-4cf5-a3cf-56f78b0ca455.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM64 DT updates for v5.4 (take two)
- Sort nodes in various SoC and board DTSes,
- HDMI sound for HiHope RZ/G2M and R-Car M3-N Salvator-X(S) boards,
- Limit EtherAVB to 100Mbps on the Ebisu and Draak boards,
- Small fixes and improvements.
* tag 'renesas-arm64-dt-for-v5.4-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (21 commits)
arm64: dts: renesas: Update 'vsps' properties for readability
arm64: dts: renesas: r8a77965-salvator-x(s): Enable HDMI sound
arm64: dts: renesas: r8a774c0: Fix register range of display node
arm64: dts: renesas: r8a77970: Sort nodes
arm64: dts: renesas: r8a7796: Sort nodes
arm64: dts: renesas: r8a774c0: Sort nodes
arm64: dts: renesas: r8a774c0: cat874: Sort nodes
arm64: dts: renesas: r8a774a1: Sort nodes
arm64: dts: renesas: r8a77980: Fix IPMMU-VC0 base address
arm64: dts: renesas: ebisu, draak: Limit EtherAVB to 100Mbps
arm64: dts: renesas: hihope-common: Add HDMI audio support
arm64: dts: renesas: r8a774c0: cat874: Add definition for 12V regulator
arm64: dts: renesas: r8a774c0: Point LVDS0 to its companion LVDS1
arm64: dts: renesas: r8a77995: Sort nodes
arm64: dts: renesas: r8a77995: draak: Sort nodes
arm64: dts: renesas: r8a77990: Sort nodes
arm64: dts: renesas: r8a77990: ebisu: Sort nodes
arm64: dts: renesas: r8a77980: v3hsk: Sort nodes
arm64: dts: renesas: r8a77980: condor: Sort nodes
arm64: dts: renesas: r8a77970: v3msk: Sort nodes
...
Link: https://lore.kernel.org/r/20190823123643.18799-4-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: Amlogic updates for v5.4
Highlights
- new SoCs (G12B family): S922X, A311D
- new SoCs (SM1 family): S905X3
- new board: SEI Robotics SEI610 (SM1/S905X3)
- new board: Khadas VIM3 (G12B/A311D)
- DVFS/CPUfreq support on G12[AB] family
* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (40 commits)
arm64: dts: add support for SM1 based SEI Robotics SEI610
dt-bindings: arm: amlogic: add SEI Robotics SEI610 bindings
dt-bindings: arm: amlogic: add SM1 bindings
arm64: dts: meson-g12b-odroid-n2: enable DVFS
arm64: dts: meson-g12b-khadas-vim3: add initial device-tree
dt-bindings: arm: amlogic: fix x96-max/sei510 section in amlogic.yaml
arm64: dts: amlogic: g12 CPU timers stop in suspend
arm64: dts: meson-g12b: support a311d and s922x cpu operating points
dt-bindings: arm: amlogic: add support for the Khadas VIM3
dt-bindings: arm: amlogic: add bindings for the Amlogic G12B based A311D SoC
dt-bindings: arm: amlogic: add bindings for G12B based S922X SoC
arm64: dts: meson: add video decoder entries
arm64: dts: meson-gx: add video decoder entry
dt-bindings: media: amlogic,vdec: add default compatible
arm64: dts: meson: add ethernet fifo sizes
arm64: dts: meson-g12b: add cpus OPP tables
arm64: dts: meson-g12a: enable DVFS on G12A boards
arm64: dts: meson-g12a: add cpus OPP table
arm64: dts: meson-g12-common: add pwm_a on GPIOE_2 pinmux
arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi
...
Link: https://lore.kernel.org/r/7hr25fbi4v.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.4
- Add reset properties for various peripherals
- QSPI OCP and DMA on Arria10
- DMA on Agilex/Stratix10
- Update NAND controller bindings to match driver update
- Add NAND controller to Stratix10
- VINING FPGA board fixups
- Update button mapping
- Adjust GMAC1 clock and TXD skew settings
- Add missing reset-names for dma controller
* tag 'socfpga_dts_updates_for_v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: add missing reset-names for dma
ARM: dts: socfpga: Adjust GMAC1 clock and TXD lines skew on VINING FPGA
ARM: dts: socfpga: Fix up button mapping on VINING FPGA
arm64: dts: stratix10: Add NAND device node
ARM: dts: socfpga: update to new Denali NAND binding
arm64: dts: agilex/stratix10: Add reset properties for DMA
ARM: dts: socfpga: add reset properties for DMA
ARM: dts: socfpga: add the QSPI OCP reset property on arria10
Link: https://lore.kernel.org/r/20190819141659.26414-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
PWM-Fan and nor-flash for the RockPro64, a better display mode for
the Kevin Chromebook and a new board the Leez P710 SBC.
* tag 'v5.4-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC
arm64: dts: rockchip: enable internal SPI flash for RockPro64.
arm64: dts: rockchip: Add PWM fan for RockPro64
arm64: dts: rockchip: Specify override mode for kevin panel
Link: https://lore.kernel.org/r/20190819141659.26414-1-dinguyen@kernel.org
Link: https://lore.kernel.org/r/2362486.gYoCZEsBuK@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is powered by
the two always on regulators (not AXP805).
WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is done
by the pio driver by reading the vcc-pg-supply voltage.
You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:
https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
Mainline brcmfmac driver expects the firmware and nvram at the following
paths relative to the firmware directory:
brcm/brcmfmac43456-sdio.bin
brcm/brcmfmac43456-sdio.txt
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The watchdog has a clock on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This patch adds RTC node and fixes the clock properties and nodes
to reflect the real clock tree.
The device nodes for the internal oscillator and osc32k are removed,
as these clocks are now provided by the RTC device. Clock references
are fixed accordingly, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.
eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s
Changes:
v3: Separate dts for eMMC variants
v2: Fix descriptions for VCC and VCCQ
Link: https://github.com/armbian/build/commit/174953de1eb09e6aa1ef7075066b573dba625398
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add device-tree nodes for i2c0 to i2c2, and also add relevant pinctrl
nodes.
Suggested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Beelink GS1 has a DDC I2C bus voltage shifter. This is actually missing
and video is limited to 1024x768 due to missing EDID information.
Add the DDC regulator in the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Beelink GS1 board has a SPDIF out connector, so enable it in
the device-tree and add a simple SPDIF soundcard.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio).
Only one pinmuxing is available so set it as default.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC
I2C bus voltage shifter. Before EDID can be read, we need to pull PH2 high.
This is realized by the ddc-en-gpios property.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Update the 'vsps' property in the R-Car Gen3 SoC device tree files to
match what's in the documentation example.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> # Salvator-XS
[geert: Preserve sort order]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Since the R8A774C0 SoC uses DU{0,1} only, the register block length
should be 0x40000.
Based on commit 06585ed38b6698bc ("arm64: dts: renesas: r8a77990: Fix
register range of display node") for R-Car E3.
Fixes: 8ed3a6b223159df3 ("arm64: dts: renesas: r8a774c0: Add display output support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add support for the Amlogic SM1 Based SEI610 board.
The SM1 SoC is a derivative of the G12A SoC Family with :
- Cortex-A55 core instead of A53
- more power domains, including USB & PCIe
- a neural network co-processor (NNA)
- a CSI input and image processor
- some changes in the audio complex, thus not yet enabled
The SEI610 board is a derivative of the SEI510 board with :
- removed ADC based touch button, replaced with 3x GPIO buttons
- physical switch disabling on-board MICs
- USB-C port for USB 2.0 OTG
- On-board FTDI USB2SERIAL port for Linux console
Audio, Display and USB support will be added later when support of the
corresponding power domains will be added, for now they are kept disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: fix minor typo regultor -> regulator]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the base address of the IPMMU-VC0 block on R-Car V3H is
0xfe990000.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
|
|
* According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode isn't supported
on R-Car E3 (r8a77990) and D3 (r8a77995).
* TX clock internal delay mode is required for reliable 1Gbps communication
using the KSZ9031RNX phy present on the Ebisu and Draak boards.
Thus, the E3 based Ebisu and D3 based Draak boards can not reliably
use 1Gbps and the speed should be limited to 100Mbps.
Based on work by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds support for HDMI audio to the device tree
common to the HiHope RZ/G2M and the HiHope RZ/G2N.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
P710 is a RK3399 based SBC, designed by Leez [0].
Specification
- Rockchip RK3399
- 4/2GB LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
[0]https://leez.lenovo.com
Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The rockpro64 contains a nor-flash chip connected to spi1.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
[a number of cleanups]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno/FVP update for v5.4
Single patch removing optional 'max-memory-bandwidth' property for CLCD
that enables to allocate and use 32bpp buffers(used on FVP for Android
development)
* tag 'juno-update-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: fast models: Remove clcd's max-memory-bandwidth
Link: https://lore.kernel.org/r/20190814172408.25995-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM64 DT updates for v5.4
- CAN, BT, and WLAN support for the HiHope RZ/G2[MN] boards,
- Sound support for RZ/G2M,
- Sort nodes in various SoC and board DTSes,
- Small fixes and improvements.
* tag 'renesas-arm64-dt-for-v5.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (23 commits)
arm64: dts: renesas: ulcb: Sort nodes
arm64: dts: renesas: ulcb-kf: Sort nodes
arm64: dts: renesas: salvator-common: Sort nodes
arm64: dts: renesas: r8a7796: salvator-xs: Sort nodes
arm64: dts: renesas: r8a7796: salvator-x: Sort nodes
arm64: dts: renesas: r8a7795: salvator-xs: Sort nodes
arm64: dts: renesas: r8a7795: salvator-x: Sort nodes
arm64: dts: renesas: r8a7795-es1: salvator-x: Sort nodes
arm64: dts: renesas: r8a77965: Sort nodes
arm64: dts: renesas: r8a7795-es1: Sort nodes
arm64: dts: renesas: r8a7795: Sort nodes
arm64: dts: renesas: r8a774a1: Add SSIU support for sound
arm64: dts: renesas: r8a774a1: Use extended audio dmac registers
arm64: dts: renesas: hihope-common: Add WLAN support
arm64: dts: renesas: hihope-common: Add BT support
arm64: dts: renesas: hihope-common: Add PCA9654 I/O expander
arm64: dts: renesas: hihope-rzg2-ex: Enable CAN interfaces
arm64: dts: renesas: r8a774a1: Add CANFD support
arm64: dts: renesas: r8a774a1: Add missing assigned-clocks for CAN[01]
arm64: dts: renesas: r8a774c0: Add missing assigned-clocks for CAN[01]
...
Link: https://lore.kernel.org/r/20190802120355.1430-2-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable DVFS for the Odroid-N2 by setting the clock, OPP and supply
for each cores of each CPU clusters.
The first cluster uses the "VDDCPU_B" power supply, and the second
cluster uses the "VDDCPU_A" power supply.
Each power supply can achieve 0.73V to 1.01V using 2 distinct PWM
outputs clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations of each cluster and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Khadas VIM3 uses the Amlogic S922X or A311S SoC, both based on the
Amlogic G12B SoC family, on a board with the same form factor as the
VIM/VIM2 models. It ships in two variants; basic and
pro which differ in RAM and eMMC size:
- 2GB (basic) or 4GB (pro) LPDDR4 RAM
- 16GB (basic) or 32GB (pro) eMMC 5.1 storage
- 16MB SPI flash
- 10/100/1000 Base-T Ethernet
- AP6398S Wireless (802.11 a/b/g/n/ac, BT5.0)
- HDMI 2.1 video
- 1x USB 2.0 + 1x USB 3.0 ports
- 1x USB-C (power) with USB 2.0 OTG
- 3x LED's (1x red, 1x blue, 1x white)
- 3x buttons (power, function, reset)
- IR receiver
- M2 socket with PCIe, USB, ADC & I2C
- 40pin GPIO Header
- 1x micro SD card slot
A common meson-g12b-khadas-vim3.dtsi is added to support both S922X and
A311D SoCs supported by two variants of the board.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Arm per-CPU architected timers stop ticking in suspend, when the
SCP powers down the CPUs. Flag that in the DT.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Meson g12b ships with a low-speed (S922X) and high-speed (A311D) variant
so remove cpu_opp_table nodes in meson-g12b.dtsi and create two new dtsi
that can be included in device-specific dts files. Opp points were taken
from the vendor BSP kernel.
Also make meson-g12b-odroid-n2.dts include the new meson-g12b-s922x.dtsi.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This enables the video decoder for GXBB, GXL and GXM chips
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the base video decoder node compatible with the meson vdec driver,
for GX* chips.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
If unspecified in DT, the fifo sizes are not automatically detected by
the dwmac1000 dma driver and the reported fifo sizes default to 0.
Because of this, flow control will be turned off on the device.
Add the fifo sizes provided by the datasheets in the SoC in DT so
flow control may be enabled if necessary.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the OPP table taken from the HardKernel Odroid-N2 DTS.
The Amlogic G12B SoC seems to available in 2 types :
- low-speed: Cortex-A73 Cluster up to 1,704GHz
- high-speed: Cortex-A73 Cluster up to 2.208GHz
The Cortex-A73 Cluster can be clocked up to 1,896GHz for both types.
The Vendor Amlogic A311D OPP table are slighly different, with lower
voltages than the HardKernel S922X tables but seems to be high-speed type.
This adds the conservative OPP table with the S922X higher voltages
and the maximum low-speed OPP frequency.
The values were tested to be stable on an HardKernel Odroid-N2 board
running the arm64 cpuburn at [1] and cycling between all the possible
cpufreq translations for both clusters and checking the final frequency
using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable DVFS for the U200, SEI520 and X96-Max Amlogic G12A based board
by setting the clock, OPP and supply for each CPU cores.
The CPU cluster power supply can achieve 0.73V to 1.01V using a PWM
output clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations and checking the final
frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the OPP table taken from the vendor u200 and u211 DTS.
The Amlogic G12A SoC seems to available in 3 types :
- low-speed: up to 1,8GHz
- mid-speed: up to 1,908GHz
- high-speed: up to 2.1GHz
And the S905X2 opp voltages are slightly higher than the S905D2
OPP voltages for the low-speed table.
This adds the conservative OPP table with the S905X2 higher voltages
and the maximum low-speed OPP frequency.
The values were tested to be stable on an Amlogic U200 Reference Board,
SeiRobotics SEI510 and X96 Max Set-Top-Boxes running the arm64 cpuburn
at [1] and cycling between all the possible cpufreq translations and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the ao_pinctrl subnode for the pwm_a function on GPIOE_2.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
To simplify the representation of differences betweem the G12A and G12B
SoCs, move the common nodes into a meson-g12-common.dtsi file and
express the CPU nodes and differences in meson-g12a.dtsi and meson-g12b.dtsi.
This separation will help for DVFS and future Amlogic SM1 Family support.
The sd_emmc_a quirk is added in the g12a/g12b since since it's already
known the sd_emmc_a controller is fixed in the next SM1 SoC family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
When powering off the Odroid N2, the tflash_vdd regulator is
automatically turned off by the kernel. This is a problem
when issuing the "reboot" command while using an SD card.
The boot ROM does not power this regulator back on, blocking
the reboot process at the boot ROM stage, preventing the
SD card from being detected.
Adding the "regulator-always-on" property fixes the problem.
Signed-off-by: Xavier Ruppen <xruppen@gmail.com>
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: c35f6dc5c377 ("arm64: dts: meson: Add minimal support for Odroid-N2")
[khilman: minor subject change: s/meson/amlogic/]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable the IR receiver controller on the SEI510 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The G12A USB2 OTG capable PHY uses a 8bit large UTMI bus, and the OTG
controller gets the PHY but width by probing the associated phy.
By default it will use 16bit wide settings if a phy is not specified,
in our case we specified the phy, but not the phy-names.
The dwc2 bindings specifies that if phys is present, phy-names shall be
"usb2-phy".
Adding phy-names = "usb2-phy" solves the OTG PHY bus configuration.
Fixes: 9baf7d6be730 ("arm64: dts: meson: g12a: Add G12A USB nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Power rail "D12.0V" comes straight from the power barrel connector,
and it's used in both main board and sub board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the new renesas,companion property to the LVDS0 node to point to the
companion LVDS encoder LVDS1.
Based on similar work from Laurent Pinchart for the r8a7799[05].
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
