Age | Commit message (Collapse) | Author |
|
clkdev_create() is a shorter way to write clkdev_alloc() followed by
clkdev_add(). Use this instead.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
|
|
* device-properties:
leds: leds-gpio: Fix multiple instances registration without 'label' property
leds: leds-gpio: Fix legacy GPIO number case
ACPI / property: Drop size_prop from acpi_dev_get_property_reference()
leds: leds-gpio: Convert gpio_blink_set() to use GPIO descriptors
ACPI / GPIO: Document ACPI GPIO mappings API
net: rfkill: gpio: Add default GPIO driver mappings for ACPI
ACPI / GPIO: Driver GPIO mappings for ACPI GPIOs
input: gpio_keys_polled: Make use of device property API
leds: leds-gpio: Make use of device property API
gpio: Support for unified device properties interface
Driver core: Unified interface for firmware node properties
input: gpio_keys_polled: Add support for GPIO descriptors
leds: leds-gpio: Add support for GPIO descriptors
gpio: sch: Consolidate core and resume banks
gpio / ACPI: Add support for _DSD device properties
misc: at25: Make use of device property API
ACPI: Allow drivers to match using Device Tree compatible property
Driver core: Unified device properties interface for platform firmware
ACPI: Add support for device specific properties
|
|
The commit "genirq: Generic chip: Change irq_reg_{readl,writel}
arguments" modified the API. In the same tome the
arch/arm/plat-orion/gpio.c file received a fix with the use of the old
API: "ARM: orion: Fix for certain sequence of request_irq can cause
irq storm". This commit fixes the use of the API.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Olof Johansson <olof@lixom.net>
Link: https://lkml.kernel.org/r/1416928752-24529-1-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Commit 21f2aae91e902aad ("leds: leds-gpio: Add support for GPIO
descriptors") already converted most of the driver to use GPIO descriptors.
What is still missing is the platform specific hook gpio_blink_set() and
board files which pass legacy GPIO numbers to this driver in platform data.
In this patch we handle the former and convert gpio_blink_set() to take
GPIO descriptor instead. In order to do this we convert the existing four
users to accept GPIO descriptor and translate it to legacy GPIO number in
the platform code. This effectively "pushes" legacy GPIO number usage from
the driver to platforms.
Also add comment to the remaining block describing that it is legacy code
path and we are getting rid of it eventually.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The problem is that hardware handled by arm/plat-orion/gpio.c,
require ack for edge irq, and no ack for level irq.
The code handle this issue, by two "struct irq_chip_type" per
one "struct irq_chip_generic". For one "struct irq_chip_generic"
irq_ack pointer is setted, for another it is NULL.
But we have only one mask_cache per two "struct irq_chip_type".
So if we
1)unmask interrupt A for "edge type" trigger,
2)unmask interrupt B for "level type" trigger,
3)unmask interrupt C for "edge type",
we, because of usage of generic irq_gc_mask_clr_bit/irq_gc_mask_set_bit,
have hardware configured to trigger interrupt B on "edge type",
because of shared mask_cache. But kernel think that B is "level type",
so when interrupt B occur via "edge" reason, we don't ack it,
and B triggered again and again.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Link: https://lkml.kernel.org/r/20140726155659.GA22977@fifteen
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev. From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.
So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following the move to pure DT-based probing of the GPIO controllers on
Orion5x, some code in plat-orion/orion-gpio.c can be removed as it is
no longer used.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1398202002-28530-39-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Following the move of the Orion5x Device Tree support to use
irqchip_init() for the interrupt controller probing, the
plat-orion/irq.c code for DT-probing of the interrupt controller is no
longer necessary, so we can get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1398202002-28530-38-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Moving to the Device Tree implies having CONFIG_MULTI_IRQ_HANDLER
enabled, even for non-DT platforms (if we want both DT and non-DT
platforms to be supported in a single kernel).
However, the common CONFIG_MULTI_IRQ_HANDLER handler for non-DT
platforms in plat-orion/irq.c doesn't match the needs of
Orion5x. Also, it doesn't make much sense for orion_irq_init() to
register the multi-IRQ handler: orion_irq_init() is called once for
each IRQ cause/mask tuple, while the multi-IRQ handler only needs to
be registered once.
To solve this problem, we move the multi-IRQ handle in per-platform
code: mach-kirkwood/irq.c and mach-dove/irq.c. The Orion5x variant
will be introduced in a followup commit. Of course, this code will
ultimately be completely removed once all boards are converted to the
Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1398202002-28530-23-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
|
|
With the gradual move to DT, kirkwood has become a lot less dependent
on plat-orion. cache-feroceon-l2.h is the last dependency. Move it out
so we can drop plat-orion when building DT only kirkwood boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
In order to support other SoC, it's required to distinguish
the 'control' timer register, from the 'rstout' register
that enables system reset on watchdog expiration.
To prevent a compatibility break, this commit adds a fallback
to a hardcoded RSTOUT address.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
mvebu fixes for v3.13 (incremental #2)
- allow building and booting DT and non-DT plat-orion SoCs
- catch proper return value for kirkwood_pm_init()
- properly check return of of_iomap to solve boot hangs (mirabox, others)
- remove a compile warning on Armada 370 with non-SMP.
* tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: mvebu: Fix kernel hang in mvebu_soc_id_init() when of_iomap failed
ARM: kirkwood: kirkwood_pm_init() should return void
ARM: orion: provide C-style interrupt handler for MULTI_IRQ_HANDLER
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with
some random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m,
i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in
industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (201 commits)
ARM: tegra: fix tegra_powergate_sequence_power_up() inline
ARM: msm_defconfig: Update for multi-platform
ARM: msm: Move MSM's DT based hardware to multi-platform support
ARM: msm: Only build timer.c if required
ARM: msm: Only build clock.c on proc_comm based platforms
ARM: ux500: Enable system suspend with WFI support
ARM: ux500: turn on PRINTK_TIME in u8500_defconfig
ARM: shmobile: r8a7790: Fix I2C controller names
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
...
|
|
DT-enabled Marvell Kirkwood and Dove SoCs make use of an irqchip
driver. As expected for irqchip drivers, it uses a C-style
interrupt handler and therefore selects MULTI_IRQ_HANDLER.
Now, compiling a kernel with both non-DT and DT support enabled,
selecting MULTI_IRQ_HANDLER will break ASM irq handler used by
non-DT boards.
Therefore, we provide a C-style irq handler even for non-DT boards,
if MULTI_IRQ_HANDLER is set. By installing the C-style irq handler
in orion_irq_init this is transparent to all non-DT board files.
While the regression report was filed on Marvell Kirkwood, also
Marvell Dove non-DT boards are affected and fixed by this patch.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Reported-by: Ian Campbell <ijc@hellion.org.uk>
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 2326f04321a9 ("ARM: kirkwood: convert to DT irqchip and clocksource")
Fixes: f07d73e33d0e ("ARM: dove: convert to DT irqchip and clocksource")
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Building with C=1 generates warnings because of missing includes and
static keywords. Add them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
With irqchip driver for Orion SoCs, reg layout of orion-intc has changed.
This updates irq driver stub implemented before to the new reg layout by
adding an offset to the base address passed by DT node. As orion5x still
uses this stub, it cannot be removed yet.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks into timers/core
Frederic sayed: "Most of these patches have been hanging around for
several month now, in -mmotm for a significant chunk. They already
missed a few releases."
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
There have never been any real users of MEMSET operations since they
have been introduced in January 2007 by commit 7405f74badf4 ("dmaengine:
refactor dmaengine around dma_async_tx_descriptor"). Therefore remove
support for them for now, it can be always brought back when needed.
[sebastian.hesselbarth@gmail.com: fix drivers/dma/mv_xor]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use irq_get_trigger_type() to get the IRQ trigger type flags
instead calling irqd_get_trigger_type(irq_get_irq_data(irq))
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/1371228049-27080-6-git-send-email-javier.martinez@collabora.co.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
When platform data were moved from arch/arm/mach-mv78xx0/common.c to
arch/arm/plat-orion/common.c with the commit "7e3819d ARM: orion:
Consolidate ethernet platform data", there were few typo made on
gigabit Ethernet interface ge10 and ge11. This commit writes back
their initial value, which allows to use this interfaces again.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.0.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Removing orion ehci include from board files will raise a compiler
error because plat/common.h is using an enum provided by orion ehci
but not including the include itself. This just adds the missing include.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
"This is the third and smallest of the SoC specific updates. Changes
include:
- SMP support for the Xilinx zynq platform
- Smaller imx changes
- LPAE support for mvebu
- Moving the orion5x, kirkwood, dove and mvebu platforms to a common
"mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus" driver.
Since this is used on multiple platforms may potentially get shared
with other architectures (powerpc and arm64), it was moved to
drivers/bus/. We expect other similar drivers to get moved to the
same place in order to avoid creating more top-level directories under
drivers/ or cluttering up the messy drivers/misc/ even more."
* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: imx: reset_controller may be disabled
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
|
|
GENERIC_GPIO has been made equivalent to GPIOLIB in architecture code
and all driver code has been switch to depend on GPIOLIB. It is thus
safe to have GENERIC_GPIO removed.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Now that all Marvell EBU platforms have been converted to use the
mvebu-mbus driver, we can remove the common plat-orion/addr-map.c code
that isn't compiled anymore.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit convers the mach-mv78xx0 sub-architecture to use the
mvebu-mbus driver. We simply have to call mvebu_mbus_init() in the
->init_early() function, and modify the PCIe code so that it uses the
new functions provided by mvebu-mbus to create the needed PCIe
windows.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit migrates the mach-orion5x platforms to use the mvebu-mbus
driver and therefore removes the Orion5x-specific addr-map code.
The dove_init_early() function now initializes the mvebu-mbus driver
by calling mvebu_mbus_init().
We also convert a number of orion5x_setup_xyz_win() calls to the
appropriate mvebu_mbus_add_window() calls, as each board was doing its
own setup for the NOR window or other devices. Ultimately, those
devices will be probed from the DT.
The common address decoding windows are now registered in the
orion5x_setup_wins() function. It is worth noting that the four PCIe
address decoding windows will ultimately no longer have to be
registered here: it will be done automatically by the PCIe driver once
Dove has been migrated to use the upcoming mvebu PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit migrates the mach-dove platforms to use the mvebu-mbus
driver and therefore removes the Dove-specific addr-map code.
The dove_init_early() function now initializes the mvebu-mbus driver
by calling mvebu_mbus_init().
The address decoding windows are now registered in the
dove_setup_cpu_wins() function. It is worth noting that the four PCIe
address decoding windows will ultimately no longer have to be
registered here: it will be done automatically by the PCIe driver once
Dove has been migrated to use the upcoming mvebu PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit migrates the mach-kirkwood platforms to use the mvebu-mbus
driver and therefore removes the Kirkwood-specific addr-map code.
The kirkwood_init_early() function is now responsible for initializing
the mvebu-mbus driver by calling mvebu_mbus_init().
The address decoding windows are now registered in the
kirkwood_setup_wins() function. It is worth noting that the four PCIe
address decoding windows will ultimately no longer have to be
registered here: it will be done automatically by the PCIe driver once
Kirkwood has been migrated to use the upcoming mvebu PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The changes needed to migrate the mach-mvebu (Armada 370 and Armada
XP) to the mvebu-mbus driver are fairly minimal, since not many
devices currently supported on those SoCs use address decoding
windows. The only one being the BootROM window, used to bring up
secondary CPUs.
However, this BootROM window needed for SMP brings an important
requirement: the mvebu-mbus driver must be initialized at the
->early_init() time, otherwise the BootROM window cannot be setup
early enough to be ready before the secondary CPUs are started.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64 into next/cleanup
* 'gic' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
irqchip: gic: Perform the gic_secondary_init() call via CPU notifier
irqchip: gic: Call handle_bad_irq() directly
arm: Move chained_irq_(enter|exit) to a generic file
arm: Move the set_handle_irq and handle_arch_irq declarations to asm/irq.h
+ Linux 3.9-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu cleanup for v3.10
- plat-orion: prep for mvebu-mbus driver
|
|
This patch adds a dedicated dbg_show function to the gpio-mvebu driver.
In addition to the generic gpiolib informations, this function displays
informations related with the specific Marvell registers (blink enable,
data in polarity, interrupt masks and cause).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch converts the Marvell MV643XX ethernet driver to use the
Marvell Orion MDIO driver. As a result, PowerPC and ARM platforms
registering the Marvell MV643XX ethernet driver are also updated to
register a Marvell Orion MDIO driver. This driver voluntarily overlaps
with the Marvell Ethernet shared registers because it will use a subset
of this shared register (shared_base + 0x4 to shared_base + 0x84). The
Ethernet driver is also updated to look up for a PHY device using the
Orion MDIO bus driver.
For ARM and PowerPC we register a single instance of the "mvmdio" driver
in the system like it used to be done with the use of the "shared_smi"
platform_data cookie on ARM.
Note that it is safe to register the mvmdio driver only for the "ge00"
instance of the driver because this "ge00" interface is guaranteed to
always be explicitely registered by consumers of
arch/arm/plat-orion/common.c and other instances (ge01, ge10 and ge11)
were all pointing their shared_smi to ge00. For PowerPC the in-tree
Device Tree Source files mention only one MV643XX ethernet MAC instance
so the MDIO bus driver is registered only when id == 0.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GPIO driver uses gpiolib, thus it should be compiled when
CONFIG_GPIOLIB is defined and not only CONFIG_GENERIC_GPIO
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PCIe code was directly accessing the orion_mbus_dram_info
structure to get access to a description of the SDRAM chip selects in
order to configure the PCIe -> SDRAM address decoding
windows.
However, with the introduction of the orion-mbus driver, we are going
to remove this global structure and instead leave only the exported
mv_mbus_dram_info() function to access this description of the SDRAM
chip selects. Therefore, we simply switch to using this API.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
-flagmail-match: MVEBU
X-flagmail-match: KIRKWOOD
X-flagmail-match: DOVE
For now, addr-map.c is needed by all 5 Marvell EBU
sub-architectures. However, we are going to introduce the orion-mbus
driver, which will replace the address decoding code from
addr-map.c. In order to ease the migration process, we will do that
one sub-architecture at a time, which will require us to remove the
compilation of addr-map.c one sub-architecture at a time.
Therefore, we split the unconditional obj-y inclusion of addr-map.c
into 5 conditionals obj-$(CONFIG_...) lines, one per sub-architecture.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
During the system initialization, the orion_setup_cpu_mbus_target()
function reads the SDRAM address decoding registers to find out how
many chip-selects of SDRAM have been enabled, and builds a small array
with one entry per chip-select. This array is then used by device
drivers (XOR, Ethernet, etc.) to configure their own address decoding
windows to the SDRAM.
However, devices can only access the first 32 bits of the physical
memory. Even though LPAE is not supported for now, some Marvell boards
are now showing up with 8 GB of RAM, configured using two SDRAM
address decoding windows: the first covering the first 4 GB, the
second covering the last 4 GB. The array built by
orion_setup_cpu_mbus_target() has therefore two entries, and device
drivers try to set up two |