Age | Commit message (Collapse) | Author |
|
The memcg uncharging code that is involved towards the end of a page's
lifetime - truncation, reclaim, swapout, migration - is impressively
complicated and fragile.
Because anonymous and file pages were always charged before they had their
page->mapping established, uncharges had to happen when the page type
could still be known from the context; as in unmap for anonymous, page
cache removal for file and shmem pages, and swap cache truncation for swap
pages. However, these operations happen well before the page is actually
freed, and so a lot of synchronization is necessary:
- Charging, uncharging, page migration, and charge migration all need
to take a per-page bit spinlock as they could race with uncharging.
- Swap cache truncation happens during both swap-in and swap-out, and
possibly repeatedly before the page is actually freed. This means
that the memcg swapout code is called from many contexts that make
no sense and it has to figure out the direction from page state to
make sure memory and memory+swap are always correctly charged.
- On page migration, the old page might be unmapped but then reused,
so memcg code has to prevent untimely uncharging in that case.
Because this code - which should be a simple charge transfer - is so
special-cased, it is not reusable for replace_page_cache().
But now that charged pages always have a page->mapping, introduce
mem_cgroup_uncharge(), which is called after the final put_page(), when we
know for sure that nobody is looking at the page anymore.
For page migration, introduce mem_cgroup_migrate(), which is called after
the migration is successful and the new page is fully rmapped. Because
the old page is no longer uncharged after migration, prevent double
charges by decoupling the page's memcg association (PCG_USED and
pc->mem_cgroup) from the page holding an actual charge. The new bits
PCG_MEM and PCG_MEMSW represent the respective charges and are transferred
to the new page during migration.
mem_cgroup_migrate() is suitable for replace_page_cache() as well,
which gets rid of mem_cgroup_replace_page_cache(). However, care
needs to be taken because both the source and the target page can
already be charged and on the LRU when fuse is splicing: grab the page
lock on the charge moving side to prevent changing pc->mem_cgroup of a
page under migration. Also, the lruvecs of both pages change as we
uncharge the old and charge the new during migration, and putback may
race with us, so grab the lru lock and isolate the pages iff on LRU to
prevent races and ensure the pages are on the right lruvec afterward.
Swap accounting is massively simplified: because the page is no longer
uncharged as early as swap cache deletion, a new mem_cgroup_swapout() can
transfer the page's memory+swap charge (PCG_MEMSW) to the swap entry
before the final put_page() in page reclaim.
Finally, page_cgroup changes are now protected by whatever protection the
page itself offers: anonymous pages are charged under the page table lock,
whereas page cache insertions, swapin, and migration hold the page lock.
Uncharging happens under full exclusion with no outstanding references.
Charging and uncharging also ensure that the page is off-LRU, which
serializes against charge migration. Remove the very costly page_cgroup
lock and set pc->flags non-atomically.
[mhocko@suse.cz: mem_cgroup_charge_statistics needs preempt_disable]
[vdavydov@parallels.com: fix flags definition]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Tested-by: Jet Chen <jet.chen@intel.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
These patches rework memcg charge lifetime to integrate more naturally
with the lifetime of user pages. This drastically simplifies the code and
reduces charging and uncharging overhead. The most expensive part of
charging and uncharging is the page_cgroup bit spinlock, which is removed
entirely after this series.
Here are the top-10 profile entries of a stress test that reads a 128G
sparse file on a freshly booted box, without even a dedicated cgroup (i.e.
executing in the root memcg). Before:
15.36% cat [kernel.kallsyms] [k] copy_user_generic_string
13.31% cat [kernel.kallsyms] [k] memset
11.48% cat [kernel.kallsyms] [k] do_mpage_readpage
4.23% cat [kernel.kallsyms] [k] get_page_from_freelist
2.38% cat [kernel.kallsyms] [k] put_page
2.32% cat [kernel.kallsyms] [k] __mem_cgroup_commit_charge
2.18% kswapd0 [kernel.kallsyms] [k] __mem_cgroup_uncharge_common
1.92% kswapd0 [kernel.kallsyms] [k] shrink_page_list
1.86% cat [kernel.kallsyms] [k] __radix_tree_lookup
1.62% cat [kernel.kallsyms] [k] __pagevec_lru_add_fn
After:
15.67% cat [kernel.kallsyms] [k] copy_user_generic_string
13.48% cat [kernel.kallsyms] [k] memset
11.42% cat [kernel.kallsyms] [k] do_mpage_readpage
3.98% cat [kernel.kallsyms] [k] get_page_from_freelist
2.46% cat [kernel.kallsyms] [k] put_page
2.13% kswapd0 [kernel.kallsyms] [k] shrink_page_list
1.88% cat [kernel.kallsyms] [k] __radix_tree_lookup
1.67% cat [kernel.kallsyms] [k] __pagevec_lru_add_fn
1.39% kswapd0 [kernel.kallsyms] [k] free_pcppages_bulk
1.30% cat [kernel.kallsyms] [k] kfree
As you can see, the memcg footprint has shrunk quite a bit.
text data bss dec hex filename
37970 9892 400 48262 bc86 mm/memcontrol.o.old
35239 9892 400 45531 b1db mm/memcontrol.o
This patch (of 4):
The memcg charge API charges pages before they are rmapped - i.e. have an
actual "type" - and so every callsite needs its own set of charge and
uncharge functions to know what type is being operated on. Worse,
uncharge has to happen from a context that is still type-specific, rather
than at the end of the page's lifetime with exclusive access, and so
requires a lot of synchronization.
Rewrite the charge API to provide a generic set of try_charge(),
commit_charge() and cancel_charge() transaction operations, much like
what's currently done for swap-in:
mem_cgroup_try_charge() attempts to reserve a charge, reclaiming
pages from the memcg if necessary.
mem_cgroup_commit_charge() commits the page to the charge once it
has a valid page->mapping and PageAnon() reliably tells the type.
mem_cgroup_cancel_charge() aborts the transaction.
This reduces the charge API and enables subsequent patches to
drastically simplify uncharging.
As pages need to be committed after rmap is established but before they
are added to the LRU, page_add_new_anon_rmap() must stop doing LRU
additions again. Revive lru_cache_add_active_or_unevictable().
[hughd@google.com: fix shmem_unuse]
[hughd@google.com: Add comments on the private use of -EAGAIN]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Until now, cftype arrays carried files for both the default and legacy
hierarchies and the files which needed to be used on only one of them
were flagged with either CFTYPE_ONLY_ON_DFL or CFTYPE_INSANE. This
gets confusing very quickly and we may end up exposing interface files
to the default hierarchy without thinking it through.
This patch makes cgroup core provide separate sets of interfaces for
cftype handling so that the cftypes for the default and legacy
hierarchies are clearly distinguished. The previous two patches
renamed the existing ones so that they clearly indicate that they're
for the legacy hierarchies. This patch adds the interface for the
default hierarchy and apply them selectively depending on the
hierarchy type.
* cftypes added through cgroup_subsys->dfl_cftypes and
cgroup_add_dfl_cftypes() only show up on the default hierarchy.
* cftypes added through cgroup_subsys->legacy_cftypes and
cgroup_add_legacy_cftypes() only show up on the legacy hierarchies.
* cgroup_subsys->dfl_cftypes and ->legacy_cftypes can point to the
same array for the cases where the interface files are identical on
both types of hierarchies.
* This makes all the existing subsystem interface files legacy-only by
default and all subsystems will have no interface file created when
enabled on the default hierarchy. Each subsystem should explicitly
review and compose the interface for the default hierarchy.
* A boot param "cgroup__DEVEL__legacy_files_on_dfl" is added which
makes subsystems which haven't decided the interface files for the
default hierarchy to present the legacy files on the default
hierarchy so that its behavior on the default hierarchy can be
tested. As the awkward name suggests, this is for development only.
* memcg's CFTYPE_INSANE on "use_hierarchy" is noop now as the whole
array isn't used on the default hierarchy. The flag is removed.
v2: Updated documentation for cgroup__DEVEL__legacy_files_on_dfl.
v3: Clear CFTYPE_ONLY_ON_DFL and CFTYPE_INSANE when cfts are removed
as suggested by Li.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
|
|
Currently, the blkio subsystem attributes all of writeback IOs to the
root. One of the issues is that there's no way to tell who originated
a writeback IO from block layer. Those IOs are usually issued
asynchronously from a task which didn't have anything to do with
actually generating the dirty pages. The memory subsystem, when
enabled, already keeps track of the ownership of each dirty page and
it's desirable for blkio to piggyback instead of adding its own
per-page tag.
blkio piggybacking on memory is an implementation detail which
preferably should be handled automatically without requiring explicit
userland action. To achieve that, this patch implements
cgroup_subsys->depends_on which contains the mask of subsystems which
should be enabled together when the subsystem is enabled.
The previous patches already implemented the support for enabled but
invisible subsystems and cgroup_subsys->depends_on can be easily
implemented by updating cgroup_refresh_child_subsys_mask() so that it
calculates cgroup->child_subsys_mask considering
cgroup_subsys->depends_on of the explicitly enabled subsystems.
Documentation/cgroups/unified-hierarchy.txt is updated to explain that
subsystems may not become immediately available after being unused
from userland and that dependency could be a factor in it. As
subsystems may already keep residual references, this doesn't
significantly change how subsystem rebinding can be used.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
|
|
cgroup is implementing support for subsystem dependency which would
require a way to enable a subsystem even when it's not directly
configured through "cgroup.subtree_control".
The previous patches added support for explicitly and implicitly
enabled subsystems and showing/hiding their interface files. An
explicitly enabled subsystem may become implicitly enabled if it's
turned off through "cgroup.subtree_control" but there are subsystems
depending on it. In such cases, the subsystem, as it's turned off
when seen from userland, shouldn't enforce any resource control.
Also, the subsystem may be explicitly turned on later again and its
interface files should be as close to the intial state as possible.
This patch adds cgroup_subsys->css_reset() which is invoked when a css
is hidden. The callback should disable resource control and reset the
state to the vanilla state.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
"A lot of activities on cgroup side. Heavy restructuring including
locking simplification took place to improve the code base and enable
implementation of the unified hierarchy, which currently exists behind
a __DEVEL__ mount option. The core support is mostly complete but
individual controllers need further work. To explain the design and
rationales of the the unified hierarchy
Documentation/cgroups/unified-hierarchy.txt
is added.
Another notable change is css (cgroup_subsys_state - what each
controller uses to identify and interact with a cgroup) iteration
update. This is part of continuing updates on css object lifetime and
visibility. cgroup started with reference count draining on removal
way back and is now reaching a point where csses behave and are
iterated like normal refcnted objects albeit with some complexities to
allow distinguishing the state where they're being deleted. The css
iteration update isn't taken advantage of yet but is planned to be
used to simplify memcg significantly"
* 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (77 commits)
cgroup: disallow disabled controllers on the default hierarchy
cgroup: don't destroy the default root
cgroup: disallow debug controller on the default hierarchy
cgroup: clean up MAINTAINERS entries
cgroup: implement css_tryget()
device_cgroup: use css_has_online_children() instead of has_children()
cgroup: convert cgroup_has_live_children() into css_has_online_children()
cgroup: use CSS_ONLINE instead of CGRP_DEAD
cgroup: iterate cgroup_subsys_states directly
cgroup: introduce CSS_RELEASED and reduce css iteration fallback window
cgroup: move cgroup->serial_nr into cgroup_subsys_state
cgroup: link all cgroup_subsys_states in their sibling lists
cgroup: move cgroup->sibling and ->children into cgroup_subsys_state
cgroup: remove cgroup->parent
device_cgroup: remove direct access to cgroup->children
memcg: update memcg_has_children() to use css_next_child()
memcg: remove tasks/children test from mem_cgroup_force_empty()
cgroup: remove css_parent()
cgroup: skip refcnting on normal root csses and cgrp_dfl_root self css
cgroup: use cgroup->self.refcnt for cgroup refcnting
...
|
|
Memory reclaim always uses swappiness of the reclaim target memcg
(origin of the memory pressure) or vm_swappiness for global memory
reclaim. This behavior was consistent (except for difference between
global and hard limit reclaim) because swappiness was enforced to be
consistent within each memcg hierarchy.
After "mm: memcontrol: remove hierarchy restrictions for swappiness and
oom_control" each memcg can have its own swappiness independent of
hierarchical parents, though, so the consistency guarantee is gone.
This can lead to an unexpected behavior. Say that a group is explicitly
configured to not swapout by memory.swappiness=0 but its memory gets
swapped out anyway when the memory pressure comes from its parent with a
It is also unexpected that the knob is meaningless without setting the
hard limit which would trigger the reclaim and enforce the swappiness.
There are setups where the hard limit is configured higher in the
hierarchy by an administrator and children groups are under control of
somebody else who is interested in the swapout behavior but not
necessarily about the memory limit.
From a semantic point of view swappiness is an attribute defining anon
vs.
file proportional scanning of LRU which is memcg specific (unlike
charges which are propagated up the hierarchy) so it should be applied
to the particular memcg's LRU regardless where the memory pressure comes
from.
This patch removes vmscan_swappiness() and stores the swappiness into
the scan_control structure. mem_cgroup_swappiness is then used to
provide the correct value before shrink_lruvec is called. The global
vm_swappiness is used for the root memcg.
[hughd@google.com: oopses immediately when booted with cgroup_disable=memory]
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Kmemcg is currently under development and lacks some important features.
In particular, it does not have support of kmem reclaim on memory pressure
inside cgroup, which practically makes it unusable in real life. Let's
warn about it in both Kconfig and Documentation to prevent complaints
arising.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Per-memcg swappiness and oom killing can currently not be tweaked on a
memcg that is part of a hierarchy, but not the root of that hierarchy.
Users have complained that they can't configure this when they turned on
hierarchy mode. In fact, with hierarchy mode becoming the default, this
restriction disables the tunables entirely.
But there is no good reason for this restriction. The settings for
swappiness and OOM killing are taken from whatever memcg whose limit
triggered reclaim and OOM invocation, regardless of its position in the
hierarchy tree.
Allow setting swappiness on any group. The knob on the root memcg
already reads the global VM swappiness, make it writable as well.
Allow disabling the OOM killer on any non-root memcg.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Tejun has correctly pointed out that tasks/children test in
mem_cgroup_force_empty is not correct because there is no other locking
which preserves this state throughout the rest of the function so both
new tasks can join the group or new children groups can be added while
somebody is writing to memory.force_empty. A new task would break
mem_cgroup_reparent_charges expectation that all failures as described
by mem_cgroup_force_empty_list are temporal and there is no way out.
The main use case for the knob as described by
Documentation/cgroups/memory.txt is to:
"
The typical use case for this interface is before calling rmdir().
Because rmdir() moves all pages to parent, some out-of-use page caches can be
moved to the parent. If you want to avoid that, force_empty will be useful.
"
This means that reparenting is not really required as rmdir will
reparent pages implicitly from the safe context. If we remove it from
mem_cgroup_force_empty then we are safe even with existing tasks because
the number of reclaim attempts is bounded. Moreover the knob still does
what the documentation claims (modulo reparenting which doesn't make any
difference) and users might expect. Longterm we want to deprecate the
whole knob and put the reparented pages to the tail of parent LRU during
cgroup removal.
tj: Removed unused variable @cgrp from mem_cgroup_force_empty()
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Unified hierarchy will be the new version of cgroup interface. This
patch adds Documentation/cgroups/unified-hierarchy.txt which describes
the design and rationales of unified hierarchy.
v2: Grammatical updates as per Randy Dunlap's review.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
|
|
mem_cgroup_newpage_charge is used only for charging anonymous memory so
it is better to rename it to mem_cgroup_charge_anon.
mem_cgroup_cache_charge is used for file backed memory so rename it to
mem_cgroup_charge_file.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The res_counter_{charge,uncharge}_locked() variants are not used in the
kernel outside of the resource counter code itself, so remove the
interface.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
|
|
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
|
|
It would be useful e.g. in a server or desktop environment to have
a facility in the notion of fine-grained "per application" or "per
application group" firewall policies. Probably, users in the mobile,
embedded area (e.g. Android based) with different security policy
requirements for application groups could have great benefit from
that as well. For example, with a little bit of configuration effort,
an admin could whitelist well-known applications, and thus block
otherwise unwanted "hard-to-track" applications like [1] from a
user's machine. Blocking is just one example, but it is not limited
to that, meaning we can have much different scenarios/policies that
netfilter allows us than just blocking, e.g. fine grained settings
where applications are allowed to connect/send traffic to, application
traffic marking/conntracking, application-specific packet mangling,
and so on.
Implementation of PID-based matching would not be appropriate
as they frequently change, and child tracking would make that
even more complex and ugly. Cgroups would be a perfect candidate
for accomplishing that as they associate a set of tasks with a
set of parameters for one or more subsystems, in our case the
netfilter subsystem, which, of course, can be combined with other
cgroup subsystems into something more complex if needed.
As mentioned, to overcome this constraint, such processes could
be placed into one or multiple cgroups where different fine-grained
rules can be defined depending on the application scenario, while
e.g. everything else that is not part of that could be dropped (or
vice versa), thus making life harder for unwanted processes to
communicate to the outside world. So, we make use of cgroups here
to track jobs and limit their resources in terms of iptables
policies; in other words, limiting, tracking, etc what they are
allowed to communicate.
In our case we're working on outgoing traffic based on which local
socket that originated from. Also, one doesn't even need to have
an a-prio knowledge of the application internals regarding their
particular use of ports or protocols. Matching is *extremly*
lightweight as we just test for the sk_classid marker of sockets,
originating from net_cls. net_cls and netfilter do not contradict
each other; in fact, each construct can live as standalone or they
can be used in combination with each other, which is perfectly fine,
plus it serves Tejun's requirement to not introduce a new cgroups
subsystem. Through this, we result in a very minimal and efficient
module, and don't add anything except netfilter code.
One possible, minimal usage example (many other iptables options
can be applied obviously):
1) Configuring cgroups if not already done, e.g.:
mkdir /sys/fs/cgroup/net_cls
mount -t cgroup -o net_cls net_cls /sys/fs/cgroup/net_cls
mkdir /sys/fs/cgroup/net_cls/0
echo 1 > /sys/fs/cgroup/net_cls/0/net_cls.classid
(resp. a real flow handle id for tc)
2) Configuring netfilter (iptables-nftables), e.g.:
iptables -A OUTPUT -m cgroup ! --cgroup 1 -j DROP
3) Running applications, e.g.:
ping 208.67.222.222 <pid:1799>
echo 1799 > /sys/fs/cgroup/net_cls/0/tasks
64 bytes from 208.67.222.222: icmp_seq=44 ttl=49 time=11.9 ms
[...]
ping 208.67.220.220 <pid:1804>
ping: sendmsg: Operation not permitted
[...]
echo 1804 > /sys/fs/cgroup/net_cls/0/tasks
64 bytes from 208.67.220.220: icmp_seq=89 ttl=56 time=19.0 ms
[...]
Of course, real-world deployments would make use of cgroups user
space toolsuite, or own custom policy daemons dynamically moving
applications from/to various cgroups.
[1] http://www.blackhat.com/presentations/bh-europe-06/bh-eu-06-biondi/bh-eu-06-biondi-up.pdf
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: cgroups@vger.kernel.org
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Correct spelling typo in memory.txt and
resource_counter.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Stop that, stop that! You're not going to do a song while I'm here.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Merge v3.12 based patch series to move cgroup_event implementation to
memcg into for-3.14. The following two commits cause a conflict in
kernel/cgroup.c
2ff2a7d03bbe4 ("cgroup: kill css_id")
79bd9814e5ec9 ("cgroup, memcg: move cgroup_event implementation to memcg")
Each patch removes a struct definition from kernel/cgroup.c. As the
two are adjacent, they cause a context conflict. Easily resolved by
removing both structs.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
cgroup_event is only available in memcg now. Let's brand it that way.
While at it, add a comment encouraging deprecation of the feature and
remove the respective section from cgroup documentation.
This patch is cosmetic.
v3: Typo update as per Li Zefan.
v2: Index in cgroups.txt updated accordingly as suggested by Li Zefan.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
|
|
The memory.numa_stat file was not hierarchical. Memory charged to the
children was not shown in parent's numa_stat.
This change adds the "hierarchical_" stats to the existing stats. The
new hierarchical stats include the sum of all children's values in
addition to the value of the memcg.
Tested: Create cgroup a, a/b and run workload under b. The values of
b are included in the "hierarchical_*" under a.
$ cd /sys/fs/cgroup
$ echo 1 > memory.use_hierarchy
$ mkdir a a/b
Run workload in a/b:
$ (echo $BASHPID >> a/b/cgroup.procs && cat /some/file && bash) &
The hierarchical_ fields in parent (a) show use of workload in a/b:
$ cat a/memory.numa_stat
total=0 N0=0 N1=0 N2=0 N3=0
file=0 N0=0 N1=0 N2=0 N3=0
anon=0 N0=0 N1=0 N2=0 N3=0
unevictable=0 N0=0 N1=0 N2=0 N3=0
hierarchical_total=908 N0=552 N1=317 N2=39 N3=0
hierarchical_file=850 N0=549 N1=301 N2=0 N3=0
hierarchical_anon=58 N0=3 N1=16 N2=39 N3=0
hierarchical_unevictable=0 N0=0 N1=0 N2=0 N3=0
$ cat a/b/memory.numa_stat
total=908 N0=552 N1=317 N2=39 N3=0
file=850 N0=549 N1=301 N2=0 N3=0
anon=58 N0=3 N1=16 N2=39 N3=0
unevictable=0 N0=0 N1=0 N2=0 N3=0
hierarchical_total=908 N0=552 N1=317 N2=39 N3=0
hierarchical_file=850 N0=549 N1=301 N2=0 N3=0
hierarchical_anon=58 N0=3 N1=16 N2=39 N3=0
hierarchical_unevictable=0 N0=0 N1=0 N2=0 N3=0
Signed-off-by: Ying Han <yinghan@google.com>
Signed-off-by: Greg Thelen <gthelen@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Sha Zhengju <handai.szj@taobao.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull core block IO updates from Jens Axboe:
"Here are the core IO block bits for 3.11. It contains:
- A tweak to the reserved tag logic from Jan, for weirdo devices with
just 3 free tags. But for those it improves things substantially
for random writes.
- Periodic writeback fix from Jan. Marked for stable as well.
- Fix for a race condition in IO scheduler switching from Jianpeng.
- The hierarchical blk-cgroup support from Tejun. This is the grunt
of the series.
- blk-throttle fix from Vivek.
Just a note that I'm in the middle of a relocation, whole family is
flying out tomorrow. Hence I will be awal the remainder of this week,
but back at work again on Monday the 15th. CC'ing Tejun, since any
potential "surprises" will most likely be from the blk-cgroup work.
But it's been brewing for a while and sitting in my tree and
linux-next for a long time, so should be solid."
* 'for-3.11/core' of git://git.kernel.dk/linux-block: (36 commits)
elevator: Fix a race in elevator switching
block: Reserve only one queue tag for sync IO if only 3 tags are available
writeback: Fix periodic writeback after fs mount
blk-throttle: implement proper hierarchy support
blk-throttle: implement throtl_grp->has_rules[]
blk-throttle: Account for child group's start time in parent while bio climbs up
blk-throttle: add throtl_qnode for dispatch fairness
blk-throttle: make throtl_pending_timer_fn() ready for hierarchy
blk-throttle: make tg_dispatch_one_bio() ready for hierarchy
blk-throttle: make blk_throtl_bio() ready for hierarchy
blk-throttle: make blk_throtl_drain() ready for hierarchy
blk-throttle: dispatch from throtl_pending_timer_fn()
blk-throttle: implement dispatch looping
blk-throttle: separate out throtl_service_queue->pending_timer from throtl_data->dispatch_work
blk-throttle: set REQ_THROTTLED from throtl_charge_bio() and gate stats update with it
blk-throttle: implement sq_to_tg(), sq_to_td() and throtl_log()
blk-throttle: add throtl_service_queue->parent_sq
blk-throttle: generalize update_disptime optimization in blk_throtl_bio()
blk-throttle: dispatch to throtl_data->service_queue.bio_lists[]
blk-throttle: move bio_lists[] and friends to throtl_service_queue
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
|
|
hugetlb cgroup has already been implemented.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Rob Landley <rob@landley.net>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Documentation for inactive_anon / active_anon was mixed up. Fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Most of the stuff from kernel/sched.c was moved to kernel/sched/core.c long time
back and the comments/Documentation never got updated.
I figured it out when I was going through sched-domains.txt and so thought of
fixing it globally.
I haven't crossed check if the stuff that is referenced in sched/core.c by all
these files is still present and hasn't changed as that wasn't the motive behind
this patch.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/cdff76a265326ab8d71922a1db5be599f20aad45.1370329560.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
With the recent updates, blk-throttle is finally ready for proper
hierarchy support. Dispatching now honors service_queue->parent_sq
and propagates correctly. The only thing missing is setting
->parent_sq correctly so that throtl_grp hierarchy matches the cgroup
hierarchy.
This patch updates throtl_pd_init() such that service_queues form the
same hierarchy as the cgroup hierarchy if sane_behavior is enabled.
As this concludes proper hierarchy support for blkcg, the shameful
.broken_hierarchy tag is removed from blkio_subsys.
v2: Updated blkio-controller.txt as suggested by Vivek.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Li Zefan <lizefan@huawei.com>
|
|
This exports the amount of anonymous transparent hugepages for each
memcg via the new "rss_huge" stat in memory.stat. The units are in
bytes.
This is helpful to determine the hugepage utilization for individual
jobs on the system in comparison to rss and opportunities where
MADV_HUGEPAGE may be helpful.
The amount of anonymous transparent hugepages is also included in "rss"
for backwards compatibility.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual stuff, mostly comment fixes, typo fixes, printk fixes and small
code cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (45 commits)
mm: Convert print_symbol to %pSR
gfs2: Convert print_symbol to %pSR
m32r: Convert print_symbol to %pSR
iostats.txt: add easy-to-find description for field 6
x86 cmpxchg.h: fix wrong comment
treewide: Fix typo in printk and comments
doc: devicetree: Fix various typos
docbook: fix 8250 naming in device-drivers
pata_pdc2027x: Fix compiler warning
treewide: Fix typo in printks
mei: Fix comments in drivers/misc/mei
treewide: Fix typos in kernel messages
pm44xx: Fix comment for "CONFIG_CPU_IDLE"
doc: Fix typo "CONFIG_CGROUP_CGROUP_MEMCG_SWAP"
mmzone: correct "pags" to "pages" in comment.
kernel-parameters: remove outdated 'noresidual' parameter
Remove spurious _H suffixes from ifdef comments
sound: Remove stray pluses from Kconfig file
radio-shark: Fix printk "CONFIG_LED_CLASS"
doc: put proper reference to CONFIG_MODULE_SIG_ENFORCE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
- Fixes and a lot of cleanups. Locking cleanup is finally complete.
cgroup_mutex is no longer exposed to individual controlelrs which
used to cause nasty deadlock issues. Li fixed and cleaned up quite a
bit including long standing ones like racy cgroup_path().
- device cgroup now supports proper hierarchy thanks to Aristeu.
- perf_event cgroup now supports proper hierarchy.
- A new mount option "__DEVEL__sane_behavior" is added. As indicated
by the name, this option is to be used for development only at this
point and generates a warning message when used. Unfortunately,
cgroup interface currently has too many brekages and inconsistencies
to implement a consistent and unified hierarchy on top. The new flag
is used to collect the behavior changes which are necessary to
implement consistent unified hierarchy. It's likely that this flag
won't be used verbatim when it becomes ready but will be enabled
implicitly along with unified hierarchy.
The option currently disables some of broken behaviors in cgroup core
and also .use_hierarchy switch in memcg (will be routed through -mm),
which can be used to make very unusual hierarc |