| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The biggest set of changes in here is the addition of the Qualcomm
RPMH driver. As well as the regualtor driver itself being quite large
due to the usual involved Qualcomm regulator stuff there's also some
code shared with the arm-soc tree, a bus driver required to
communicate with the hardware that actually winds up being much larger
than the regulator driver itself and a LLCC driver that was part of
the same signed tag used with the arm-soc tree.
Other than that it's a fairly standard and quiet release, highlights
include:
- Addition of device links from regulator consumers to their
regulators, helping the core avoid dependency issues during
suspend.
- Support for the entertainingly innovative suspend implementation in
the BD9571MWV.
- Support for switch regulators on the PFUZE100, this required two
goes due to backwards compatibility issues with old DTs that were
discovered.
- Support for Freescale PFUZE3001 and SocioNext UniPhier.
- The aforementioned Qualcomm RPMH driver together with the driver
changes required to support it"
* tag 'regulator-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (52 commits)
regulator: add QCOM RPMh regulator driver
regulator: dt-bindings: add QCOM RPMh regulator bindings
regulator: samsung: Add SPDX license identifiers
regulator: maxim: Add SPDX license identifiers
regulator: bd71837: adobt MFD changes to regulator driver
regulator: tps65217: Fix NULL pointer dereference on probe
regulator: Add support for CPCAP regulators on Motorola Xoom devices.
regulator: Add sw2_sw4 voltage table to cpcap regulator.
regulator: bd9571mwv: Make symbol 'dev_attr_backup_mode' static
regulator: pfuze100: add support to en-/disable switch regulators
regulator: pfuze100: add optional disable switch-regulators binding
soc: qcom: rmtfs-mem: fix memleak in probe error paths
soc: qcom: llc-slice: Add missing MODULE_LICENSE()
drivers: qcom: rpmh: fix unwanted error check for get_tcs_of_type()
drivers: qcom: rpmh-rsc: fix the loop index check in get_req_from_tcs
firmware: qcom: scm: add a dummy qcom_scm_assign_mem()
drivers: qcom: rpmh-rsc: Check cmd_db_ready() to help children
drivers: qcom: rpmh-rsc: allow active requests from wake TCS
drivers: qcom: rpmh: add support for batch RPMH request
drivers: qcom: rpmh: allow requests to be sent asynchronously
...
|
|
Pull block updates from Jens Axboe:
"First pull request for this merge window, there will also be a
followup request with some stragglers.
This pull request contains:
- Fix for a thundering heard issue in the wbt block code (Anchal
Agarwal)
- A few NVMe pull requests:
* Improved tracepoints (Keith)
* Larger inline data support for RDMA (Steve Wise)
* RDMA setup/teardown fixes (Sagi)
* Effects log suppor for NVMe target (Chaitanya Kulkarni)
* Buffered IO suppor for NVMe target (Chaitanya Kulkarni)
* TP4004 (ANA) support (Christoph)
* Various NVMe fixes
- Block io-latency controller support. Much needed support for
properly containing block devices. (Josef)
- Series improving how we handle sense information on the stack
(Kees)
- Lightnvm fixes and updates/improvements (Mathias/Javier et al)
- Zoned device support for null_blk (Matias)
- AIX partition fixes (Mauricio Faria de Oliveira)
- DIF checksum code made generic (Max Gurtovoy)
- Add support for discard in iostats (Michael Callahan / Tejun)
- Set of updates for BFQ (Paolo)
- Removal of async write support for bsg (Christoph)
- Bio page dirtying and clone fixups (Christoph)
- Set of bcache fix/changes (via Coly)
- Series improving blk-mq queue setup/teardown speed (Ming)
- Series improving merging performance on blk-mq (Ming)
- Lots of other fixes and cleanups from a slew of folks"
* tag 'for-4.19/block-20180812' of git://git.kernel.dk/linux-block: (190 commits)
blkcg: Make blkg_root_lookup() work for queues in bypass mode
bcache: fix error setting writeback_rate through sysfs interface
null_blk: add lock drop/acquire annotation
Blk-throttle: reduce tail io latency when iops limit is enforced
block: paride: pd: mark expected switch fall-throughs
block: Ensure that a request queue is dissociated from the cgroup controller
block: Introduce blk_exit_queue()
blkcg: Introduce blkg_root_lookup()
block: Remove two superfluous #include directives
blk-mq: count the hctx as active before allocating tag
block: bvec_nr_vecs() returns value for wrong slab
bcache: trivial - remove tailing backslash in macro BTREE_FLAG
bcache: make the pr_err statement used for ENOENT only in sysfs_attatch section
bcache: set max writeback rate when I/O request is idle
bcache: add code comments for bset.c
bcache: fix mistaken comments in request.c
bcache: fix mistaken code comments in bcache.h
bcache: add a comment in super.c
bcache: avoid unncessary cache prefetch bch_btree_node_get()
bcache: display rate debug parameters to 0 when writeback is not running
...
|
|
Add tracking of REQ_OP_DISCARD ios to the partition statistics and
append them to the various stat files in /sys as well as
/proc/diskstats. These are tracked with the same four stats as reads
and writes:
Number of discard ios completed.
Number of discard ios merged
Number of discard sectors completed
Milliseconds spent on discard requests
This is done via adding a new STAT_DISCARD define to genhd.h and then
using it to index that stat field for discard requests.
tj: Refreshed on top of v4.17 and other previous updates.
Signed-off-by: Michael Callahan <michaelcallahan@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andy Newell <newella@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Introduce the 'l1tf=' kernel command line option to allow for boot-time
switching of mitigation that is used on processors affected by L1TF.
The possible values are:
full
Provides all available mitigations for the L1TF vulnerability. Disables
SMT and enables all mitigations in the hypervisors. SMT control via
/sys/devices/system/cpu/smt/control is still possible after boot.
Hypervisors will issue a warning when the first VM is started in
a potentially insecure configuration, i.e. SMT enabled or L1D flush
disabled.
full,force
Same as 'full', but disables SMT control. Implies the 'nosmt=force'
command line option. sysfs control of SMT and the hypervisor flush
control is disabled.
flush
Leaves SMT enabled and enables the conditional hypervisor mitigation.
Hypervisors will issue a warning when the first VM is started in a
potentially insecure configuration, i.e. SMT enabled or L1D flush
disabled.
flush,nosmt
Disables SMT and enables the conditional hypervisor mitigation. SMT
control via /sys/devices/system/cpu/smt/control is still possible
after boot. If SMT is reenabled or flushing disabled at runtime
hypervisors will issue a warning.
flush,nowarn
Same as 'flush', but hypervisors will not warn when
a VM is started in a potentially insecure configuration.
off
Disables hypervisor mitigations and doesn't emit any warnings.
Default is 'flush'.
Let KVM adhere to these semantics, which means:
- 'lt1f=full,force' : Performe L1D flushes. No runtime control
possible.
- 'l1tf=full'
- 'l1tf-flush'
- 'l1tf=flush,nosmt' : Perform L1D flushes and warn on VM start if
SMT has been runtime enabled or L1D flushing
has been run-time enabled
- 'l1tf=flush,nowarn' : Perform L1D flushes and no warnings are emitted.
- 'l1tf=off' : L1D flushes are not performed and no warnings
are emitted.
KVM can always override the L1D flushing behavior using its 'vmentry_l1d_flush'
module parameter except when lt1f=full,force is set.
This makes KVM's private 'nosmt' option redundant, and as it is a bit
non-systematic anyway (this is something to control globally, not on
hypervisor level), remove that option.
Add the missing Documentation entry for the l1tf vulnerability sysfs file
while at it.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20180713142323.202758176@linutronix.de
|
|
Provide a command line and a sysfs knob to control SMT.
The command line options are:
'nosmt': Enumerate secondary threads, but do not online them
'nosmt=force': Ignore secondary threads completely during enumeration
via MP table and ACPI/MADT.
The sysfs control file has the following states (read/write):
'on': SMT is enabled. Secondary threads can be freely onlined
'off': SMT is disabled. Secondary threads, even if enumerated
cannot be onlined
'forceoff': SMT is permanentely disabled. Writes to the control
file are rejected.
'notsupported': SMT is not supported by the CPU
The command line option 'nosmt' sets the sysfs control to 'off'. This
can be changed to 'on' to reenable SMT during runtime.
The command line option 'nosmt=force' sets the sysfs control to
'forceoff'. This cannot be changed during runtime.
When SMT is 'on' and the control file is changed to 'off' then all online
secondary threads are offlined and attempts to online a secondary thread
later on are rejected.
When SMT is 'off' and the control file is changed to 'on' then secondary
threads can be onlined again. The 'off' -> 'on' transition does not
automatically online the secondary threads.
When the control file is set to 'forceoff', the behaviour is the same as
setting it to 'off', but the operation is irreversible and later writes to
the control file are rejected.
When the control status is 'notsupported' then writes to the control file
are rejected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
|
|
This file doesn't exist anymore:
Documentation/cpu-freq/user-guide.txt
As the ABI already points to Documentation/cpu-freq, just
remove the broken link and the associated text.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
The script:
./scripts/documentation-file-ref-check --fix
Gives multiple hints for broken references on some files.
Manually use the one that applies for some files.
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Several incremental improvements including new keycodes, new models,
new quirks, and related documentation. Adds LED platform driver
activation for Mellanox systems. Some minor optimizations and
cleanups. Includes several bug fixes, message silencing, mostly minor
Automated summary:
acer-wmi:
- add another KEY_POWER keycode
apple-gmux:
- fix gmux_get_client_id()'s return type
asus-laptop:
- Simplify getting .drvdata
asus-wireless:
- Fix format specifier
dell-laptop:
- Fix keyboard backlight timeout on XPS 13 9370
dell-smbios:
- Match on www.dell.com in OEM strings too
dell-wmi:
- Ignore new rfkill and fn-lock events
- Set correct keycode for Fn + left arrow
fujitsu-laptop:
- Simplify soft key handling
ideapad-laptop:
- Add E42-80 to no_hw_rfkill
- Add fn-lock setting
- Add MIIX 720-12IKB to no_hw_rfkill
lib/string_helpers:
- Add missed declaration of struct task_struct
intel_scu_ipc:
- Replace mdelay with usleep_range in intel_scu_ipc_i2c_cntrl
mlx-platform:
- Add LED platform driver activation
platform/mellanox:
- Add new ODM system types to mlx-platform
- mlxreg-hotplug: add extra cycle for hotplug work queue
- mlxreg-hotplug: Document fixes for hotplug private data
platform_data/mlxreg:
- Document fixes for hotplug device
silead_dmi:
- Add entry for Chuwi Hi8 tablet touchscreen
- Add touchscreen info for the Onda V891w tablet
- Add info for the PoV mobii TAB-P800W (v2.0)
- Add touchscreen info for the Jumper EZpad 6 Pro
thinkpad_acpi:
- silence false-positive-prone pr_warn
- do not report thermal sensor state for tablet mode switch
- silence HKEY 0x6032, 0x60f0, 0x6030"
* tag 'platform-drivers-x86-v4.18-1' of git://git.infradead.org/linux-platform-drivers-x86: (30 commits)
platform/x86: silead_dmi: Add entry for Chuwi Hi8 tablet touchscreen
platform/x86: dell-laptop: Fix keyboard backlight timeout on XPS 13 9370
platform/x86: dell-wmi: Ignore new rfkill and fn-lock events
platform/x86: mlx-platform: Add LED platform driver activation
platform/mellanox: Add new ODM system types to mlx-platform
platform/mellanox: mlxreg-hotplug: add extra cycle for hotplug work queue
platform/x86: ideapad-laptop: Add E42-80 to no_hw_rfkill
platform/x86: silead_dmi: Add touchscreen info for the Onda V891w tablet
platform/x86: silead_dmi: Add info for the PoV mobii TAB-P800W (v2.0)
platform/x86: silead_dmi: Add touchscreen info for the Jumper EZpad 6 Pro
platform/x86: asus-wireless: Fix format specifier
platform/x86: asus-wmi: Fix NULL pointer dereference
platform/x86: dell-wmi: Set correct keycode for Fn + left arrow
platform/x86: acer-wmi: add another KEY_POWER keycode
platform/x86: ideapad-laptop: Add fn-lock setting
platform/x86: ideapad-laptop: Add MIIX 720-12IKB to no_hw_rfkill
lib/string_helpers: Add missed declaration of struct task_struct
platform/x86: DELL_WMI use depends on instead of select for DELL_SMBIOS
platform/mellanox: mlxreg-hotplug: Document fixes for hotplug private data
platform_data/mlxreg: Document fixes for hotplug device
...
|
|
Pull rpmsg updates from Bjorn Andersson:
"This migrates rpmsg to use SPDX license headers and fixes a
use-after-free in SMD"
* tag 'rpmsg-v4.18' of git://github.com/andersson/remoteproc:
rpmsg: smd: do not use mananged resources for endpoints and channels
rpmsg: char: Switch to SPDX license identifier
rpmsg: glink: Switch to SPDX license identifier
rpmsg: smd: Switch to SPDX license identifier
rpmsg: virtio_rpmsg_bus: Switch to SPDX license identifier
rpmsg: Switch to SPDX license identifier
rpmsg: qcom_smd: Access APCS through mailbox framework
rpmsg: Add driver_override device attribute for rpmsg_device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"In this round, we've mainly focused on discard, aka unmap, control
along with fstrim for Android-specific usage model. In addition, we've
fixed writepage flow which returned EAGAIN previously resulting in EIO
of fsync(2) due to mapping's error state. In order to avoid old MM bug
[1], we decided not to use __GFP_ZERO for the mapping for node and
meta page caches. As always, we've cleaned up many places for future
fsverity and symbol conflicts.
Enhancements:
- do discard/fstrim in lower priority considering fs utilization
- split large discard commands into smaller ones for better responsiveness
- add more sanity checks to address syzbot reports
- add a mount option, fsync_mode=nobarrier, which can reduce # of cache flushes
- clean up symbol namespace with modified function names
- be strict on block allocation and IO control in corner cases
Bug fixes:
- don't use __GFP_ZERO for mappings
- fix error reports in writepage to avoid fsync() failure
- avoid selinux denial on CAP_RESOURCE on resgid/resuid
- fix some subtle race conditions in GC/atomic writes/shutdown
- fix overflow bugs in sanity_check_raw_super
- fix missing bits on get_flags
Clean-ups:
- prepare the generic flow for future fsverity integration
- fix some broken coding standard"
[1] https://lkml.org/lkml/2018/4/8/661
* tag 'f2fs-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (79 commits)
f2fs: fix to clear FI_VOLATILE_FILE correctly
f2fs: let sync node IO interrupt async one
f2fs: don't change wbc->sync_mode
f2fs: fix to update mtime correctly
fs: f2fs: insert space around that ':' and ', '
fs: f2fs: add missing blank lines after declarations
fs: f2fs: changed variable type of offset "unsigned" to "loff_t"
f2fs: clean up symbol namespace
f2fs: make set_de_type() static
f2fs: make __f2fs_write_data_pages() static
f2fs: fix to avoid accessing cross the boundary
f2fs: fix to let caller retry allocating block address
disable loading f2fs module on PAGE_SIZE > 4KB
f2fs: fix error path of move_data_page
f2fs: don't drop dentry pages after fs shutdown
f2fs: fix to avoid race during access gc_thread pointer
f2fs: clean up with clear_radix_tree_dirty_tag
f2fs: fix to don't trigger writeback during recovery
f2fs: clear discard_wake earlier
f2fs: let discard thread wait a little longer if dev is busy
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big staging and IIO driver update for 4.18-rc1.
It was delayed as I wanted to make sure the final driver deletions did
not cause any major merge issues, and all now looks good.
There are a lot of patches here, just over 1000. The diffstat summary
shows the major changes here:
1007 files changed, 16828 insertions(+), 227770 deletions(-)
Because of this, we might be close to shrinking the overall kernel
source code size for two releases in a row.
There was loads of work in this release cycle, primarily:
- tons of ks7010 driver cleanups
- lots of mt7621 driver fixes and cleanups
- most driver cleanups
- wilc1000 fixes and cleanups
- lots and lots of IIO driver cleanups and new additions
- debugfs cleanups for all staging drivers
- lots of other staging driver cleanups and fixes, the shortlog has
the full details.
but the big user-visable things here are the removal of 3 chunks of
code:
- ncpfs and ipx were removed on schedule, no one has cared about this
code since it moved to staging last year, and if it needs to come
back, it can be reverted.
- lustre file system is removed.
I've ranted at the lustre developers about once a year for the past
5 years, with no real forward progress at all to clean things up
and get the code into the "real" part of the kernel.
Given that the lustre developers continue to work on an external
tree and try to port those changes to the in-kernel tree every once
in a while, this whole thing really really is not working out at
all. So I'm deleting it so that the developers can spend the time
working in their out-of-tree location and get things cleaned up
properly to get merged into the tree correctly at a later date.
Because of these file removals, you will have merge issues on some of
these files (2 in the ipx code, 1 in the ncpfs code, and 1 in the
atomisp driver). Just delete those files, it's a simple merge :)
All of this has been in linux-next for a while with no reported
problems"
* tag 'staging-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1011 commits)
staging: ipx: delete it from the tree
ncpfs: remove uapi .h files
ncpfs: remove Documentation
ncpfs: remove compat functionality
staging: ncpfs: delete it
staging: lustre: delete the filesystem from the tree.
staging: vc04_services: no need to save the log debufs dentries
staging: vc04_services: vchiq_debugfs_log_entry can be a void *
staging: vc04_services: remove struct vchiq_debugfs_info
staging: vc04_services: move client dbg directory into static variable
staging: vc04_services: remove odd vchiq_debugfs_top() wrapper
staging: vc04_services: no need to check debugfs return values
staging: mt7621-gpio: reorder includes alphabetically
staging: mt7621-gpio: change gc_map to don't use pointers
staging: mt7621-gpio: use GPIOF_DIR_OUT and GPIOF_DIR_IN macros instead of custom values
staging: mt7621-gpio: change 'to_mediatek_gpio' to make just a one line return
staging: mt7621-gpio: dt-bindings: update documentation for #interrupt-cells property
staging: mt7621-gpio: update #interrupt-cells for the gpio node
staging: mt7621-gpio: dt-bindings: complete documentation for the gpio
staging: mt7621-dts: add missing properties to gpio node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This adds a user for the new 'bytes-remaining' updates to
memcpy_mcsafe() that you already received through Ingo via the
x86-dax- for-linus pull.
Not included here, but still targeting this cycle, is support for
handling memory media errors (poison) consumed via userspace dax
mappings.
Summary:
- DAX broke a fundamental assumption of truncate of file mapped
pages. The truncate path assumed that it is safe to disconnect a
pinned page from a file and let the filesystem reclaim the physical
block. With DAX the page is equivalent to the filesystem block.
Introduce dax_layout_busy_page() to enable filesystems to wait for
pinned DAX pages to be released. Without this wait a filesystem
could allocate blocks under active device-DMA to a new file.
- DAX arranges for the block layer to be bypassed and uses
dax_direct_access() + copy_to_iter() to satisfy read(2) calls.
However, the memcpy_mcsafe() facility is available through the pmem
block driver. In order to safely handle media errors, via the DAX
block-layer bypass, introduce copy_to_iter_mcsafe().
- Fix cache management policy relative to the ACPI NFIT Platform
Capabilities Structure to properly elide cache flushes when they
are not necessary. The table indicates whether CPU caches are
power-fail protected. Clarify that a deep flush is always performed
on REQ_{FUA,PREFLUSH} requests"
* tag 'libnvdimm-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (21 commits)
dax: Use dax_write_cache* helpers
libnvdimm, pmem: Do not flush power-fail protected CPU caches
libnvdimm, pmem: Unconditionally deep flush on *sync
libnvdimm, pmem: Complete REQ_FLUSH => REQ_PREFLUSH
acpi, nfit: Remove ecc_unit_size
dax: dax_insert_mapping_entry always succeeds
libnvdimm, e820: Register all pmem resources
libnvdimm: Debug probe times
linvdimm, pmem: Preserve read-only setting for pmem devices
x86, nfit_test: Add unit test for memcpy_mcsafe()
pmem: Switch to copy_to_iter_mcsafe()
dax: Report bytes remaining in dax_iomap_actor()
dax: Introduce a ->copy_to_iter dax operation
uio, lib: Fix CONFIG_ARCH_HAS_UACCESS_MCSAFE compilation
xfs, dax: introduce xfs_break_dax_layouts()
xfs: prepare xfs_break_layouts() for another layout type
xfs: prepare xfs_break_layouts() to be called with XFS_MMAPLOCK_EXCL
mm, fs, dax: handle layout changes to pinned dax mappings
mm: fix __gup_device_huge vs unmap
mm: introduce MEMORY_DEVICE_FS_DAX and CONFIG_DEV_PAGEMAP_OPS
...
|
|
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull integrity updates from James Morris:
"From Mimi:
- add run time support for specifying additional security xattrs
included in the security.evm HMAC/signature
- some code clean up and bug fixes"
* 'next-integrity' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
EVM: unlock on error path in evm_read_xattrs()
EVM: prevent array underflow in evm_write_xattrs()
EVM: Fix null dereference on xattr when xattr fails to allocate
EVM: fix memory leak of temporary buffer 'temp'
IMA: use list_splice_tail_init_rcu() instead of its open coded variant
ima: use match_string() helper
ima: fix updating the ima_appraise flag
ima: based on policy verify firmware signatures (pre-allocated buffer)
ima: define a new policy condition based on the filesystem name
EVM: Allow runtime modification of the set of verified xattrs
EVM: turn evm_config_xattrnames into a list
integrity: Add an integrity directory in securityfs
ima: Remove unused variable ima_initialized
ima: Unify logging
ima: Reflect correct permissions for policy
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove of atomisp driver from staging, as nobody would have time to
dedicate huge efforts to fix all the problems there. Also, we have a
feeling that the driver may not even run the way it is.
- move Zoran driver to staging, in order to be either fixed to use VB2
and the proper media kAPIs or to be removed
- remove videobuf-dvb driver, with is unused for a while
- some V4L2 documentation fixes/improvements
- new sensor drivers: imx258 and ov7251
- a new driver was added to allow using I2C transparent drivers
- several improvements at the ddbridge driver
- several improvements at the ISDB pt1 driver, making it more coherent
with the DVB framework
- added a new platform driver for MIPI CSI-2 RX: cadence
- now, all media drivers can be compiled on x86 with COMPILE_TEST
- almost all media drivers now build on non-x86 architectures with
COMPILE_TEST
- lots of other random stuff: cleanups, support for new board models,
bug fixes, etc
* tag 'media/v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
media: omap2: fix compile-testing with FB_OMAP2=m
media: media/radio/Kconfig: add back RADIO_ISA
media: v4l2-ioctl.c: fix missing unlock in __video_do_ioctl()
media: pxa_camera: ignore -ENOIOCTLCMD from v4l2_subdev_call for s_power
media: arch: sh: migor: Fix TW9910 PDN gpio
media: staging: tegra-vde: Reset VDE regardless of memory client resetting failure
media: marvel-ccic: mmp: select VIDEOBUF2_VMALLOC/DMA_CONTIG
media: marvel-ccic: allow ccic and mmp drivers to coexist
media: uvcvideo: Prevent setting unavailable flags
media: ddbridge: conditionally enable fast TS for stv0910-equipped bridges
media: dvb-frontends/stv0910: make TS speed configurable
media: ddbridge/mci: add identifiers to function definition arguments
media: ddbridge/mci: protect against out-of-bounds array access in stop()
media: rc: ensure input/lirc device can be opened after register
media: rc: nuvoton: Keep device enabled during reg init
media: rc: nuvoton: Keep track of users on CIR enable/disable
media: rc: nuvoton: Tweak the interrupt enabling dance
media: uvcvideo: Support realtek's UVC 1.5 device
media: uvcvideo: Fix driver reference counting
media: gspca_zc3xx: Enable short exposure times for OV7648
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support
live patching again.
- Add support for patching barrier_nospec in copy_from_user() and
syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu
Malaterre.
- Several series optimising various parts of the 32-bit code from
Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K"
("GEFanuc,C2K"), which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by
Steve, and a fix to our powernv cpuidle driver. Then there's a series
touching mm, x86 and fs/proc/task_mmu.c, which cleans up some details
around pkey support. It was ack'ed/reviewed by Ingo & Dave and has
been in next for several weeks.
Thanks to: Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al
Viro, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd
Bergmann, Balbir Singh, Cédric Le Goater, Christophe Leroy, Christophe
Lombard, Colin Ian King, Dave Hansen, Fabio Estevam, Finn Thain,
Frederic Barrat, Gautham R. Shenoy, Haren Myneni, Hari Bathini, Ingo
Molnar, Jonathan Neuschäfer, Josh Poimboeuf, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu Malaterre,
Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica
Gupta, Ravi Bangoria, Russell Currey, Sam Bobroff, Samuel
Mendoza-Jonas, Segher Boessenkool, Shilpasri G Bhat, Simon Guo,
Souptick Joarder, Stewart Smith, Thiago Jung Bauermann, Torsten Duwe,
Vaibhav Jain, Wei Yongjun, Wolfram Sang, Yisheng Xie, YueHaibing"
* tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (251 commits)
powerpc/64s/radix: Fix missing ptesync in flush_cache_vmap
cpuidle: powernv: Fix promotion from snooze if next state disabled
powerpc: fix build failure by disabling attribute-alias warning in pci_32
ocxl: Fix missing unlock on error in afu_ioctl_enable_p9_wait()
powerpc-opal: fix spelling mistake "Uniterrupted" -> "Uninterrupted"
powerpc: fix spelling mistake: "Usupported" -> "Unsupported"
powerpc/pkeys: Detach execute_only key on !PROT_EXEC
powerpc/powernv: copy/paste - Mask SO bit in CR
powerpc: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove support for Marvell mv64x60 i2c controller
powerpc/boot: Remove support for Marvell MPSC serial controller
powerpc/embedded6xx: Remove C2K board support
powerpc/lib: optimise PPC32 memcmp
powerpc/lib: optimise 32 bits __clear_user()
powerpc/time: inline arch_vtime_task_switch()
powerpc/Makefile: set -mcpu=860 flag for the 8xx
powerpc: Implement csum_ipv6_magic in assembly
powerpc/32: Optimise __csum_partial()
powerpc/lib: Adjust .balign inside string functions for PPC32
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the "big" char and misc driver patches for 4.18-rc1.
It's not a lot of stuff here, but there are some highlights:
- coreboot driver updates
- soundwire driver updates
- android binder updates
- fpga big sync, mostly documentation
- lots of minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (81 commits)
vmw_balloon: fixing double free when batching mode is off
MAINTAINERS: Add driver-api/fpga path
fpga: clarify that unregister functions also free
documentation: fpga: move fpga-region.txt to driver-api
documentation: fpga: add bridge document to driver-api
documentation: fpga: move fpga-mgr.txt to driver-api
Documentation: fpga: move fpga overview to driver-api
fpga: region: kernel-doc fixes
fpga: bridge: kernel-doc fixes
fpga: mgr: kernel-doc fixes
fpga: use SPDX
fpga: region: change api, add fpga_region_create/free
fpga: bridge: change api, don't use drvdata
fpga: manager: change api, don't use drvdata
fpga: region: don't use drvdata in common fpga code
Drivers: hv: vmbus: Removed an unnecessary cast from void *
ver_linux: Drop redundant calls to system() to test if file is readable
ver_linux: Move stderr redirection from function parameter to function body
misc: IBM Virtual Management Channel Driver (VMC)
rpmsg: Correct support for MODULE_DEVICE_TABLE()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
|
|
Pull documentation updates from Jonathan Corbet:
"There's been a fair amount of work in the docs tree this time around,
including:
- Extensive RST conversions and organizational work in the
memory-management docs thanks to Mike Rapoport.
- An update of Documentation/features from Andrea Parri and a script
to keep it updated.
- Various LICENSES updates from Thomas, along with a script to check
SPDX tags.
- Work to fix dangling references to documentation files; this
involved a fair number of one-liner comment changes outside of
Documentation/
... and the usual list of documentation improvements, typo fixes, etc"
* tag 'docs-4.18' of git://git.lwn.net/linux: (103 commits)
Documentation: document hung_task_panic kernel parameter
docs/admin-guide/mm: add high level concepts overview
docs/vm: move ksm and transhuge from "user" to "internals" section.
docs: Use the kerneldoc comments for memalloc_no*()
doc: document scope NOFS, NOIO APIs
docs: update kernel versions and dates in tables
docs/vm: transhuge: split userspace bits to admin-guide/mm/transhuge
docs/vm: transhuge: minor updates
docs/vm: transhuge: change sections order
Documentation: arm: clean up Marvell Berlin family info
Documentation: gpio: driver: Fix a typo and some odd grammar
docs: ranoops.rst: fix location of ramoops.txt
scripts/documentation-file-ref-check: rewrite it in perl with auto-fix mode
docs: uio-howto.rst: use a code block to solve a warning
mm, THP, doc: Add document for thp_swpout/thp_swpout_fallback
w1: w1_io.c: fix a kernel-doc warning
Documentation/process/posting: wrap text at 80 cols
docs: admin-guide: add cgroup-v2 documentation
Revert "Documentation/features/vm: Remove arch support status file for 'pte_special'"
Documentation: refcount-vs-atomic: Update reference to LKMM doc.
...
|
|
The "Clear Error Unit" may be smaller than the ECC unit size on some
devices. For example, poison may be tracked at 64-byte alignment even
though the ECC unit is larger. Unless / until the ACPI specification
provides a non-ambiguous way to communicate this property do not expose
this to userspace.
Software that had been using this property must already be prepared for
the case where the property is not provided on older kernels, so it is
safe to remove this attribute.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
We ended up with an ugly conflict between fixes and next in ftrace.h
involving multiple nested ifdefs, and the automatic resolution is
wrong. So merge fixes into next so we can fix it up.
|
|
Currently we see a kernel-oops reported on Power-9 while attaching a
context to an AFU, with radix-mode and sysfs attr 'prefault_mode' set
to anything other than 'none'. The backtrace of the oops is of this
form:
Unable to handle kernel paging request for data at address 0x00000080
Faulting instruction address: 0xc00800000bcf3b20
cpu 0x1: Vector: 300 (Data Access) at [c00000037f003800]
pc: c00800000bcf3b20: cxl_load_segment+0x178/0x290 [cxl]
lr: c00800000bcf39f0: cxl_load_segment+0x48/0x290 [cxl]
sp: c00000037f003a80
msr: 9000000000009033
dar: 80
dsisr: 40000000
current = 0xc00000037f280000
paca = 0xc0000003ffffe600 softe: 3 irq_happened: 0x01
pid = 3529, comm = afp_no_int
<snip>
cxl_prefault+0xfc/0x248 [cxl]
process_element_entry_psl9+0xd8/0x1a0 [cxl]
cxl_attach_dedicated_process_psl9+0x44/0x130 [cxl]
native_attach_process+0xc0/0x130 [cxl]
afu_ioctl+0x3f4/0x5e0 [cxl]
do_vfs_ioctl+0xdc/0x890
ksys_ioctl+0x68/0xf0
sys_ioctl+0x40/0xa0
system_call+0x58/0x6c
The issue is caused as on Power-8 the AFU attr 'prefault_mode' was
used to improve initial storage fault performance by prefaulting
process segments. However on Power-9 with radix mode we don't have
Storage-Segments that we can prefault. Also prefaulting process Pages
will be too costly and fine-grained.
Hence, since the prefaulting mechanism doesn't makes sense of
radix-mode, this patch updates prefault_mode_store() to not allow any
other value apart from CXL_PREFAULT_NONE when radix mode is enabled.
Fixes: f24be42aab37 ("cxl: Add psl9 specific code")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The file is called "features", not "feature".
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
Currently, the USB hub core waits for 50 ms after enumerating the
device. This was added to help "some high speed devices" to
enumerate (b789696af8 "[PATCH] USB: relax usbcore reset timings").
On some devices, the time-to-active is important, so we provide
a per-port option to reduce the time to what the USB specification
requires: 10 ms.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "old" enumeration scheme is considerably faster (it takes
~244ms instead of ~356ms to get the descriptor).
It is currently only possible to use the old scheme globally
(/sys/module/usbcore/parameters/old_scheme_first), which is not
desirable as the new scheme was introduced to increase compatibility
with more devices.
However, in our case, we care about time-to-active for a specific
USB device (which we make the firmware for), on a specific port
(that is pogo-pin based: not a standard USB port). This new
sysfs option makes it possible to use the old scheme on a single
port only.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now, we issue discard asynchronously in separated thread instead of in
checkpoint, after that, we won't encounter long latency in checkpoint
due to huge number of synchronous discard command handling, so, we don't
need to split checkpoint to do trim in batch, merge it and obsolete
related sysfs entry.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
If/when file data signatures are distributed with the file data, this
patch will not be needed. In the current environment where only some
files are signed, the ability to differentiate between file systems is
needed. Some file systems consider the file system magic number
internal to the file system.
This patch defines a new IMA policy condition named "fsname", based on
the superblock's file_system_type (sb->s_type) name. This allows policy
rules to be expressed in terms of the filesystem name.
The following sample rules require file signatures on rootfs files
executed or mmap'ed.
appraise func=BPRM_CHECK fsname=rootfs appraise_type=imasig
appraise func=FILE_MMAP fsname=rootfs appraise_type=imasig
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Theodore Ts'o <tytso@mit.edu>
|
|
Some of latest Lenovo ideapad laptops do not have UEFI/BIOS setting for
switching fn-lock mode. This commit adds related acpi calls to ideapad
platform driver. However setting is available via sysfs.
Signed-off-by: Oleg Keri <ezhi99@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Merge speculative store buffer bypass fixes from Thomas Gleixner:
- rework of the SPEC_CTRL MSR management to accomodate the new fancy
SSBD (Speculative Store Bypass Disable) bit handling.
- the CPU bug and sysfs infrastructure for the exciting new Speculative
Store Bypass 'feature'.
- support for disabling SSB via LS_CFG MSR on AMD CPUs including
Hyperthread synchronization on ZEN.
- PRCTL support for dynamic runtime control of SSB
- SECCOMP integration to automatically disable SSB for sandboxed
processes with a filter flag for opt-out.
- KVM integration to allow guests fiddling with SSBD including the new
software MSR VIRT_SPEC_CTRL to handle the LS_CFG based oddities on
AMD.
- BPF protection against SSB
.. this is just the core and x86 side, other architecture support will
come separately.
* 'speck-v20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (49 commits)
bpf: Prevent memory disambiguation attack
x86/bugs: Rename SSBD_NO to SSB_NO
KVM: SVM: Implement VIRT_SPEC_CTRL support for SSBD
x86/speculation, KVM: Implement support for VIRT_SPEC_CTRL/LS_CFG
x86/bugs: Rework spec_ctrl base and mask logic
x86/bugs: Remove x86_spec_ctrl_set()
x86/bugs: Expose x86_spec_ctrl_base directly
x86/bugs: Unify x86_spec_ctrl_{set_guest,restore_host}
x86/speculation: Rework speculative_store_bypass_update()
x86/speculation: Add virtualized speculative store bypass disable support
x86/bugs, KVM: Extend speculation control for VIRT_SPEC_CTRL
x86/speculation: Handle HT correctly on AMD
x86/cpufeatures: Add FEATURE_ZEN
x86/cpufeatures: Disentangle SSBD enumeration
x86/cpufeatures: Disentangle MSR_SPEC_CTRL enumeration from IBRS
x86/speculation: Use synthetic bits for IBRS/IBPB/STIBP
KVM: SVM: Move spec control call after restore of GS
x86/cpu: Make alternative_msr_write work for 32-bit code
x86/bugs: Fix the parameters alignment and missing void
x86/bugs: Make cpu_show_common() static
...
|
|
We want the bug fixes and this resolves the merge issues with the usbip
driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sites may wish to provide additional metadata alongside files in order
to make more fine-grained security decisions[1]. The security of this is
enhanced if this metadata is protected, something that EVM makes
possible. However, the kernel cannot know about the set of extended
attributes that local admins may wish to protect, and hardcoding this
policy in the kernel makes it difficult to change over time and less
convenient for distributions to enable.
This patch adds a new /sys/kernel/security/integrity/evm/evm_xattrs node,
which can be read to obtain the current set of EVM-protected extended
attributes or written to in order to add new entries. Extending this list
will not change the validity of any existing signatures provided that the
file in question does not have any of the additional extended attributes -
missing xattrs are skipped when calculating the EVM hash.
[1] For instance, a package manager could install information about the
package uploader in an additional extended attribute. Local LSM policy
could then be associated with that extended attribute in order to
restrict the privileges available to packages from less trusted
uploaders.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Reviewed-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
|
|
Failure to synchronize the tunneled operations does not prevent
the initialization of the cxl card. This patch reports the tunneled
operations status via /sys.
Signed-off-by: Philippe Bergheaud <felix@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In 4.9 kernel, the sysfs files for Hyper-V VMBus changed name but
the documentation files were not updated. The current sysfs file
names are /sys/bus/vmbus/devices/<UUID>/...
See commit 9a56e5d6a0ba ("Drivers: hv: make VMBus bus ids persistent")
and commit f6b2db084b65 ("vmbus: make sysfs names consistent with PCI")
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed |
