| Age | Commit message (Collapse) | Author |
|---|
|
Host needs to pass at least on bssid with all 0xff to firmware in
WMI_START_SCAN_CMDID, otherwise the bssid and receiver address
in probe requeste are all ZEROs.
This also fixed some hidden AP connection issue because some AP
doesn't respond to probe request which receiver address are all
ZEROs.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201012101733.24137-1-cjhuang@codeaurora.org
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/wmi.c:279: warning: Function parameter or member 'ptr_' not described in 'wmi_buffer_block'
drivers/net/wireless/ath/wil6210/wmi.c:279: warning: Excess function parameter 'ptr' description in 'wmi_buffer_block'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-2-lee.jones@linaro.org
|
|
This patch calls wcn36xx_smd_keep_alive_req() on the STA patch immediately
after associating with an AP.
This will cause the firmware to send a NULL packet out to the AP every 30
seconds, thus offloading keep-alive processing from the SoC to the
firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-4-bryan.odonoghue@linaro.org
|
|
This patch switches on CONNECTION_MONITOR. Once done it is up to the
firmware to send keep alive and to monitor the link state.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-3-bryan.odonoghue@linaro.org
|
|
The firmware parameter LINK_FAIL_TX_CNT maps to the prima configuration
file parameter gLinkFailTxCnt and is described as:
quote: " If within gLinkFailTimeout period(values is mentioned in msec) if
FW doesn't receive acks for gLinkFailTxCnt number of packets, then
link will be disconnected."
The downstream description sets a minimum value of 1000 a maximum value of
60000 and a default value of 6000, however it appears that unless we
actually set this value deliberately firmware defaults it to 0.
Setting this value to non-zero results in the firmware doing link
monitoring. The working example from downstream paradoxically sets the
value to 200, here we opt to set the value to the minimum stipulated in the
configuration file 1000.
In conjunction with ieee80211_hw_set(wcn->hw, CONNECTION_MONITOR); this
change effects offload of link monitoring to the firmware.
Tested with:
'CNSS-PR-2-0-1-2-c1-74-130449-3' wcn3620
'CNSS-PR-2-0-1-2-c1-00083' wcn3680
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-2-bryan.odonoghue@linaro.org
|
|
gcc -Wextra points out a type mismatch
drivers/net/wireless/ath/ath6kl/wmi.c: In function 'ath6kl_wmi_cmd_send':
drivers/net/wireless/ath/ath6kl/wmi.c:1825:19: warning: implicit conversion from 'enum <anonymous>' to 'enum wmi_data_hdr_data_type' [-Wenum-conversion]
1825 | false, false, 0, NULL, if_idx);
| ^~~~~
As far as I can tell, the numeric value is current here,
so just use the correct enum literal instead of 'false'.
Fixes: bdcd81707973 ("Add ath6kl cleaned up driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-9-arnd@kernel.org
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/dynack.c:52: warning: Function parameter or member 'old' not described in 'ath_dynack_ewma'
drivers/net/wireless/ath/ath9k/dynack.c:52: warning: Function parameter or member 'new' not described in 'ath_dynack_ewma'
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-40-lee.jones@linaro.org
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'rfBuf' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'reg32' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'numBits' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'firstBit' not described in 'ar5008_hw_phy_modify_rx_buffer'
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-21-lee.jones@linaro.org
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h:1734:18: warning: ‘ar9300PciePhy_clkreq_disable_L1_2p2’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h:1727:18: warning: ‘ar9300PciePhy_clkreq_enable_L1_2p2’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-14-lee.jones@linaro.org
|
|
'ar9485_fast_clock_1_1_baseband_postamble'
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9485_initvals.h:1009:18: warning: ‘ar9485_fast_clock_1_1_baseband_postamble’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-13-lee.jones@linaro.org
|
|
'ar9340Modes_ub124_tx_gain_table_1p0'
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9340_initvals.h:624:18: warning: ‘ar9340Modes_ub124_tx_gain_table_1p0’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-12-lee.jones@linaro.org
|
|
'ar9331_common_tx_gain_offset1_1'
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9330_1p1_initvals.h:1013:18: warning: ‘ar9331_common_tx_gain_offset1_1’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-11-lee.jones@linaro.org
|
|
There are only a couple of these and none of them are conformant.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/dfs_pri_detector.c:39: warning: Function parameter or member 'head' not described in 'pulse_elem'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'val' not described in 'pde_get_multiple'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'fraction' not described in 'pde_get_multiple'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'tolerance' not described in 'pde_get_multiple'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-23-lee.jones@linaro.org
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/dfs_pattern_detector.c:34: warning: Function parameter or member 'region' not described in 'radar_types'
drivers/net/wireless/ath/dfs_pattern_detector.c:141: warning: Function parameter or member 'region' not described in 'get_dfs_domain_radar_types'
drivers/net/wireless/ath/dfs_pattern_detector.c:239: warning: Function parameter or member 'dpd' not described in 'channel_detector_get'
drivers/net/wireless/ath/dfs_pattern_detector.c:239: warning: Function parameter or member 'freq' not described in 'channel_detector_get'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-22-lee.jones@linaro.org
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/regd.c:378: warning: Function parameter or member 'reg' not described in 'ath_reg_apply_ir_flags'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-20-lee.jones@linaro.org
|
|
Japan has new Radar types as per latest regulatory,
included under MKK_N in FW. So adding new enum in
ath11k to support it.
Tested-on: IPQ8074 hw2.0 PCI WLAN.HK.2.4.0.1-00041-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604563475-5782-1-git-send-email-lavaks@codeaurora.org
|
|
Assign the correct hw_op ath11k_init_wmi_config_ipq8074 to
the hw IPQ8074. Also update the correct TWT radio count.
Incorrect TWT radio count cause TWT feature fails on radio2
because physical device count is hardcoded to 2. so set
the value dynamically.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Fixes: 2d4bcbed5b7d53e1 ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604512020-25197-1-git-send-email-periyasa@codeaurora.org
|
|
Below listed hal descriptor mask are incorrect, so modify it to correct one
- CE destination status description meta info mask is increased from
8 bits to 16 bits from the 0th bit position
- Rx Reo queue duplicate count mask is decreased from 22 bits to 16 bits
- Reo threshold status counter sum mask is increased from 24 bits to 26 bits
No functionality impact, these descriptors are currently not used in any
supported platform. But in future if someone referred these descriptor then
ended with wrong values.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511921-24840-1-git-send-email-periyasa@codeaurora.org
|
|
driver not able to bootup in the single radio configured board.
single phy hw mode is converted to invalid hw mode and sent to FW
through wmi init cmd. In that case driver is not receiving wmi
ready event which leads to driver bootup fail. single phy hw mode
is a valid for single radio configured board. so removed the
conversion logic.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511331-22477-1-git-send-email-periyasa@codeaurora.org
|
|
The ath11k code will try to insert wheather rader related limits when the
DFS region is set to ETSI. For this reason, it will add two more entries in
the array of reg_rules. But the 2.4.0.1 firmware is prefiltering the list
of reg rules it returns for 2.4GHz PHYs. They will then not contain the
list of 5GHz rules and thus no wheather radar band rules were inserted by
this code.
But the code didn't fix the n_reg_rules for this regulatory domain and PHY
when this happened. This resulted in a rejection by is_valid_rd because it
found rules which start and end at 0khz. This resulted in a splat like:
Invalid regulatory domain detected
------------[ cut here ]------------
WARNING: at backports-20200628-4.4.60-9a94b73e75/net/wireless/reg.c:3721
[...]
ath11k c000000.wifi1: failed to perform regd update : -22
The number of rules must therefore be saved after they were converted from
the ath11k format to the ieee80211_regdomain format and not before.
Tested with IPQ8074 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030101940.2387952-1-sven@narfation.org
|
|
qdf_ctx is not used in wmi_mgmt_params, remove this
un-used variable.
Compile tested only.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603339175-12706-1-git-send-email-govinds@codeaurora.org
|
|
The function ath11k_wmi_send_init_country_cmd is taking 3 byte from alpha2
of the structure wmi_init_country_params. But the function
ath11k_reg_notifier is only initializing 2 bytes. The third byte is
therefore always an uninitialized value.
The command can happen to look like
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 f8 00
instead of
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 00 00
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201021140555.4114715-1-sven@narfation.org
|
|
cold boot calibration is the process to calibrate all the channels
during the boot-up to avoid the calibration delay during the
channel change.
During the boot-up, firmware started in cold boot calibration mode
Firmware calibrate all channels and generate CalDb(DDR).
Subsequent wifi bringup will reuse the same CalDb.
Firmware is restarted in normal mode to continue the normal operation.
caldb memory address send to firmware through the QMI message.Firmware
use this address to store the caldb data and use it until next reboot.
This will give the improvement during the channel change. But it is
increasing the boot-up time(up to 15sec depend on number of radios).
So if the user want to reduce the boot-up time and accepting for channel
change delay, user can disable this feature using the module param
cold_boot_cal=0.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org
|
|
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on IPQ6018 using bus, qmi-chip-id and
qmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
This problem was already solved on ath10k by adding a ",variant=.*" at the
end of the board name. The same functionality must also be provided for
ath11k.
The device tree requires an additional string to define the variant name
wifi@c000000 {
status = "okay";
qcom,ath11k-calibration-variant = "Cigtech-WF-188";
};
This would create the boarddata identifier for the board-2.bin search
* bus=ahb,qmi-chip-id=0,qmi-board-id=18,variant=Cigtech-WF-188
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-2-sven@narfation.org
|
|
The bus + qmi-chip-id + qmi-board-id is not enough to identify the correct
board data file on IPQ6018 based devices. Multiple different boards share
the same values. Only the original reference designs can currently be
identified and loaded from the board-2.bin. But these will not result in
the correct calibration data when combined with the pre-calibration data
from the device.
An additional "variant" information has to be provided to select the
correct board data for a design which was modified by an ODM. This follows
the same approach as ath10k.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-1-sven@narfation.org
|
|
Monitor ring Rx buffer is not really modified between dma map
and unmap. So remove the unnecssary data sync before dma unmap.
This does not fix any visible issue, found in code review.
Compile tested only.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602744454-22969-1-git-send-email-vthiagar@codeaurora.org
|
|
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007103309.363737-4-allen.lkml@gmail.com
|
|
The rx worker of SDIO should be cancelled after disable interrupt, and
release rx sk_buff in queue, otherwise the rx worker maybe still run
after hif_stop. And it should be cancelled before napi_synchronize in
hif_stop, because the rx worker of SDIO will call napi_schedule, it
should have no napi_schedule before napi_synchronize, otherwise it
lead napi_synchronize wait untill napi_complete.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604558036-4056-1-git-send-email-wgong@codeaurora.org
|
|
This fixes possible crash scenario where interfaces that were not
set up in the driver yet might still be iterated over. When originally
debugged on the ath10k-ct driver, the crash looked like this:
kernel BUG at /home/greearb/git/linux-4.7.dev.y/drivers/net/wireless/ath/ath10k/wmi.c:1781!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
Modules linked in: nf_conntrack_netlink nf_conntrack nfnetlink nf_defrag_ipv4 bridge carl9170 mac80211_hwsim ath10k_pci ath10k_core ath5k ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 8021q garp mrp stp llc bnep bluetooth fuse macvlan pktgen rpcsec_gss_krb5 nfsv4 nfs fscache snd_hda_codec_hdmi coretemp hwmon intel_rapl x86_pkg_temp_thermal intel_powerclamp snd_hda_codec_realtek snd_hda_codec_generic kvm iTCO_wdt irqbypass iTCO_vendor_support joydev snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device pcspkr snd_pcm snd_timer shpchp snd i2c_i801 lpc_ich soundcore tpm_tis tpm nfsd auth_rpcgss nfs_acl lockd grace sunrpc i915 serio_raw i2c_algo_bit drm_kms_helper ata_generic e1000e pata_acpi drm ptp pps_core i2c_core fjes video ipv6 [last unloaded: nf_conntrack]
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.7.10+ #15
Hardware name: To be filled by O.E.M. To be filled by O.E.M./ChiefRiver, BIOS 4.6.5 06/07/2013
task: ffff8801d4f20000 ti: ffff8801d4f28000 task.ti: ffff8801d4f28000
RIP: 0010:[<ffffffffa0efbcfb>] [<ffffffffa0efbcfb>] ath10k_wmi_tx_beacons_iter+0x28b/0x290 [ath10k_core]
RSP: 0018:ffff8801d6447a98 EFLAGS: 00010293
RAX: 0000000000000018 RBX: ffff8801ce97e1d8 RCX: 0000000000000000
RDX: 0000000000000018 RSI: 0000000000000003 RDI: ffffed003ac88f49
RBP: ffff8801d6447af0 R08: 0000000000000003 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000
R13: ffff8801ce97e320 R14: ffff8801ce97e378 R15: ffff8801ce97ca40
FS: 0000000000000000(0000) GS:ffff8801d6440000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007eff191ef1ab CR3: 000000000260a000 CR4: 00000000001406e0
Stack:
1ffff1003ac88f59 0000000041b58ab3 ffffffffa0f4d52a ffff8801d4f20000
0000000000000246 0000000000000002 ffff8801ce97e1d8 ffff8801bd5d39b8
0000000000000002 0000000000000001 ffff8801ce97ca40 ffff8801d6447b48
Call Trace:
<IRQ>
[<ffffffffa0d03e5c>] __iterate_interfaces+0xfc/0x1d0 [mac80211]
[<ffffffffa0efba70>] ? ath10k_wmi_cmd_send_nowait+0x260/0x260 [ath10k_core]
[<ffffffffa0efba70>] ? ath10k_wmi_cmd_send_nowait+0x260/0x260 [ath10k_core]
[<ffffffffa0d04477>] ieee80211_iterate_active_interfaces_atomic+0x67/0x100 [mac80211]
[<ffffffffa0d04410>] ? ieee80211_handle_reconfig_failure+0x140/0x140 [mac80211]
[<ffffffffa0ef4060>] ? ath10k_tpc_config_disp_tables+0x620/0x620 [ath10k_core]
[<ffffffffa0ef408b>] ath10k_wmi_op_ep_tx_credits+0x2b/0x50 [ath10k_core]
[<ffffffffa0ee2fd2>] ath10k_htc_rx_completion_handler+0x422/0x5c0 [ath10k_core]
[<ffffffffa0b4301e>] ath10k_pci_process_rx_cb+0x37e/0x430 [ath10k_pci]
[<ffffffffa0ee2bb0>] ? ath10k_htc_build_tx_ctrl_skb+0xc0/0xc0 [ath10k_core]
[<ffffffffa0b42ca0>] ? ath10k_pci_rx_post_pipe+0x550/0x550 [ath10k_pci]
[<ffffffff8120cbe5>] ? debug_lockdep_rcu_enabled+0x35/0x40
[<ffffffff811e1893>] ? mark_held_locks+0x23/0xc0
[<ffffffff8116019a>] ? __local_bh_enable_ip+0x6a/0xd0
[<ffffffff811e1abb>] ? trace_hardirqs_on_caller+0x18b/0x290
[<ffffffff811e1bcd>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff8116019a>] ? __local_bh_enable_ip+0x6a/0xd0
[<ffffffff81df11d0>] ? _raw_spin_unlock_bh+0x30/0x40
[<ffffffffa0b4902e>] ? ath10k_ce_per_engine_service+0xee/0x100 [ath10k_pci]
[<ffffffffa0b43139>] ath10k_pci_htt_htc_rx_cb+0x29/0x30 [ath10k_pci]
[<ffffffffa0b48fe6>] ath10k_ce_per_engine_service+0xa6/0x100 [ath10k_pci]
[<ffffffffa0b49116>] ath10k_ce_per_engine_service_any+0xd6/0xf0 [ath10k_pci]
[<ffffffffa0b45800>] ? ath10k_pci_enable_legacy_irq+0xe0/0xe0 [ath10k_pci]
[<ffffffffa0b4585f>] ath10k_pci_tasklet+0x5f/0xb0 [ath10k_pci]
[<ffffffff81160445>] tasklet_action+0x245/0x2b0
[<ffffffff81df4831>] __do_softirq+0x181/0x595
[<ffffffff8116137c>] irq_exit+0xbc/0xc0
[<ffffffff81df423c>] do_IRQ+0x7c/0x150
[<ffffffff81df23cc>] common_interrupt+0x8c/0x8c
<EOI>
[<ffffffff811e1abb>] ? trace_hardirqs_on_caller+0x18b/0x290
[<ffffffff81b722ae>] ? cpuidle_enter_state+0x1ae/0x4b0
[<ffffffff81b722a7>] ? cpuidle_enter_state+0x1a7/0x4b0
[<ffffffff81b72602>] cpuidle_enter+0x12/0x20
[<ffffffff811d0b6e>] call_cpuidle+0x4e/0x90
[<ffffffff811d10e7>] cpu_startup_entry+0x3f7/0x540
[<ffffffff811d0cf0>] ? default_idle_call+0x50/0x50
[<ffffffff81234bdf>] ? clockevents_config_and_register+0x5f/0x70
[<ffffffff81085a9a>] ? setup_APIC_timer+0xfa/0x110
[<ffffffff81083b63>] start_secondary+0x253/0x2b0
[<ffffffff81083910>] ? set_cpu_sibling_map+0x920/0x920
Code: 4d 49 e0 8b b3 48 01 00 00 48 c7 c7 a0 ee f3 a0 e8 d9 c2 3f e0 49 81 fd 3f 1f 00 00 76 0f 49 81 fc 3f 1f 00 00 0f 87 c0 fd ff ff <0f> 0b 0f 0b 90 55 48 89 e5 41 57 41 56 48 8d 85 58 ff ff ff 41
RIP [<ffffffffa0efbcfb>] ath10k_wmi_tx_beacons_iter+0x28b/0x290 [ath10k_core]
RSP <ffff8801d6447a98>
---[ end trace 6588464714e5163a ]---
Similar logic was tested for years in ath10k-ct driver and various firmware.
Also tested with stock kernel plus this patch, with firmware
10.2.4-1.0-00037
This test case was to bring up 5 vap on a radio and fake a firmware
crash. Make sure ap interfaces continue to function properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200922191957.25257-2-greearb@candelatech.com
|
|
This change fixes below compilation warning.
smatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:9125 ath10k_mac_op_set_tid_config() error: uninitialized symbol 'ret'.
No functional changes. Compile tested only.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604507837-29361-1-git-send-email-tamizhr@codeaurora.org
|
|
This patch adds driver support for FILS discovery and unsolicited
broadcast probe response transmission features which are used for
in-band discovery in 6GHz band.
Currently this support is enabled only in 6GHz by setting hardware flags.
Changes include WMI commands to enable transmission, set packet
interval, set template, and handle events.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007204036.19780-1-alokad@codeaurora.org
|
|
The for loop checks whether cur_section is NULL on every iteration, but
we know it can never be NULL as there is another check towards the
bottom of the loop body. Refactor to avoid this unnecessary check.
Also, increment the variable i inline for clarity
Addresses-Coverity: 1496984 ("Null pointer dereferences)
Suggested-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200916165748.20927-1-alex.dewar90@gmail.com
|
|
Found by latest checkpatch.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603803705-22447-1-git-send-email-kvalo@codeaurora.org
|
|
Latest checkpatch complains about use of fall-through comment. But as this is a
switch statement just reword the comment to workaround the problem.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603802288-21158-2-git-send-email-kvalo@codeaurora.org
|
|
Found by latest checkpatch.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603802288-21158-1-git-send-email-kvalo@codeaurora.org
|
|
|
|
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace". So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 453431a54934 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.
Since then a few more instances of kzfree() have slipped in.
Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.
If GIT_DIR is unset, keep using the current ".git" default.
Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A time namespace fix and a matching selftest. The futex absolute
timeouts which are based on CLOCK_MONOTONIC require time namespace
corrected. This was missed in the original time namesapce support"
* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
selftests/timens: Add a test for futex()
futex: Adjust absolute futex timeouts with per time namespace offset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Two scheduler fixes:
- A trivial build fix for sched_feat() to compile correctly with
CONFIG_JUMP_LABEL=n
- Replace a zero lenght array with a flexible array"
* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/features: Fix !CONFIG_JUMP_LABEL case
sched: Replace zero-length array with flexible-array
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Thomas Gleixner:
"A single fix to compute the field offset of the SNOOPX bit in the data
source bitmask of perf events correctly"
* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: correct SNOOPX field offset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Thomas Gleixner:
"Just a trivial fix for kernel-doc warnings"
* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/seqlocks: Fix kernel-doc warnings
|
|
Pull NTB fixes from Jon Mason.
* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
NTB: Use struct_size() helper in devm_kzalloc()
ntb: intel: Fix memleak in intel_ntb_pci_probe
NTB: hw: amd: fix an issue about leak system resources
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"Regression fix for rc1 and stable kernels as well"
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs
|
|
Pull more cifs updates from Steve French:
"Add support for stat of various special file types (WSL reparse points
for char, block, fifo)"
* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number
smb3: add some missing definitions from MS-FSCC
smb3: remove two unused variables
smb3: add support for stat of WSL reparse points for special file types
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc updates from Helge Deller:
- During this merge window O_NONBLOCK was changed to become 000200000,
but we missed that the syscalls timerfd_create(), signalfd4(),
eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
bit-wise check of the flags parameter.
To provide backward compatibility with existing userspace we
introduce parisc specific wrappers for those syscalls which filter
out the old O_NONBLOCK value and replaces it with the new one.
- Prevent HIL bus driver to get stuck when keyboard or mouse isn't
attached
- Improve error return codes when setting rtc time
- Minor documentation fix in pata_ns87415.c
* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
ata: pata_ns87415.c: Document support on parisc with superio chip
parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
hil/parisc: Disable HIL driver when it gets stuck
parisc: Improve error return codes when setting rtc time
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- a series for the Xen pv block drivers adding module parameters for
better control of resource usge
- a cleanup series for the Xen event driver
* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Documentation: add xen.fifo_events kernel parameter description
xen/events: unmask a fifo event channel only if it was masked
xen/events: only register debug interrupt for 2-level events
xen/events: make struct irq_info private to events_base.c
xen: remove no longer used functions
xen-blkfront: Apply changed parameter name to the document
xen-blkfront: add a parameter for disabling of persistent grants
xen-blkback: add a parameter for disabling of persistent grants
|
|
Pull SafeSetID updates from Micah Morton:
"The changes are mostly contained to within the SafeSetID LSM, with the
exception of a few 1-line changes to change some ns_capable() calls to
ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
is examined by SafeSetID code and nothing else in the kernel.
The changes to SafeSetID internally allow for setting up GID
transition security policies, as already existed for UIDs"
* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
LSM: SafeSetID: Fix warnings reported by test bot
LSM: SafeSetID: Add GID security policy handling
LSM: Signal to SafeSetID when setting group IDs
|
