Age | Commit message (Collapse) | Author |
|
Convert ov2680 sensor bindings documentation to yaml schema, remove
the textual bindings document and update MAINTAINERS entry.
Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Comment has 'the' repeated twice. Let's clean it up.
This patch reduces checkpatch warnings for this file to nil.
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Because clk_disable_unprepare() already checked NULL clock parameter,
so the additional check is unnecessary, just remove it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
OTP data access of ov2740 need enable the streaming mode to load
and it could be done in any time, so driver need allow the OTP
data access during streaming instead of return EBUSY, this patch
try to read the OTP data out in STREAMON if OTP data is not ready
before first time streaming start.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
OTP data access of ov2740 in probe need power up, it may cause
the camera flash LED blink during probe if the LED use same power
rail with camera, this patch move the OTP data access out of
probe, it will only occur on demand from user by nvmem sysfs.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add support of BT656 embedded synchronization bus.
This mode allows to save hardware synchro lines hsync & vsync by replacing
them with synchro codes embedded in data stream.
This bus type is only compatible with 8 bits width data bus.
Due to reserved values 0x00 & 0xff used for synchro codes, valid data vary
from 0x1 to 0xfe, this is up to sensor to clip accordingly pixel data. As
a consequence of this clipping, JPEG is not supported with this bus type.
DCMI crop feature is also not available with this bus type.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add support of BT656 embedded synchronization bus mode in DCMI driver.
Add "bus-type" property and make it required so that there is no
ambiguity between parallel mode (bus-type=5) and BT656 mode (bus-type=6).
BT656 mode allows to save hardware synchro lines hsync & vsync by replacing
them with synchro codes embedded in data stream, hence hsync-active &
vsync-active properties are useless in this mode.
With DCMI, BT656 bus mode is only compatible with 8 bits width data bus.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add a v4l2 sub-device driver for the OminiVision ov9734 image sensor
which can deliver maximum 720p image frames at 30 fps. This driver
also add vertical blanking, exposure, test pattern, digital and analog
gain control for the image sensor.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There are few nice macros in mm.h, some of which we may use here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In two places time32 structures were defined, but they are not
used if CONFIG_COMPAT_32BIT_TIME is not set. Put these two structs
under #ifdef CONFIG_COMPAT_32BIT_TIME as well to clearly indicate
that they are only used if that config option is set.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Fix to goto snd_error in error handling case when fails
to do snd_ctl_add, as done elsewhere in this function.
Fixes: 28cae868cd24 ("[media] solo6x10: move out of staging into drivers/media/pci.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Fix this smatch error:
saa7134-video.c:1286 saa7134_g_fmt_vid_overlay() error: we previously assumed 'f->fmt.win.clips' could be null (see line 1279)
This is actually a false error since if f->fmt.win.clips is NULL, clipcount
will be set to 0, so the clips array won't be touched, but it doesn't hurt
to make this explicit in the code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
cx231xx_close_extension and hence cx231xx_audio_fini() are called with the
cx231xx device lock held, but snd_cx231xx_pcm_close() also grabs that mutex
when closing the file on behalf of arecord. There seems to be no reason to
wait for sound card resources to be released, so let the release be
asynchronous.
Tested with a Hauppauge 955Q (2040:b123) and Linux 5.9.6; the hang
described in the bug no longer occurs and disconnecting the device
correctly terminates arecord with ENODEV.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=204087
Signed-off-by: Zebediah Figura <zfigura@codeweavers.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Prevent NULL (or close to NULL) pointer dereference in various places by
registering the video device only when the V4L2 m2m framework has been set
up.
Fixes: commit 96d8eab5d0a1 ("V4L/DVB: [v5,2/2] v4l: Add a mem-to-mem videobuf framework test device")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
remove check for V4L2_CTRL_TYPE_BUTTON from
v4l2_ctrl_request_clone and v4l2_ctrl_request_setup().
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
All the items in the TODO list were addressed, uapi was reviewed,
documentation written, checkpatch errors fixed, several bugs fixed.
There is no big reason to keep this driver in staging, so move it out.
Dt-bindings Verified with:
make ARCH=arm64 dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/media/rockchip-isp1.yaml
Fields of MAINTAINERS file sorted according to output of
./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS
--order
[dt-bindings: media: rkisp1: move rockchip-isp1 bindings out of staging]
[dt-bindings: media: rkisp1: move rockchip-isp1 bindings out of staging]
[hverkuil: fix various checkpatch alignment warnings]
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add the Rockchip ISP1 specific processing parameter format
V4L2_META_FMT_RK_ISP1_PARAMS and metadata format
V4L2_META_FMT_RK_ISP1_STAT_3A for 3A.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The dma engine should be stopped first.
The driver waits for an interrupt to stop the stream in a known state
after a frame.
If rkisp1_cap_stream_disable() is called after stopping the rest of the
pipeline, then most likely the interrupt won't arrive, we'll get a
timeout and debugfs variables mp_stop_timeout or sp_stop_timeout will
be incremented.
Fixes: 37db540bb9d1f ("media: staging: rkisp1: cap: refactor enable/disable stream to allow multistreaming")
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
When device_create() fails, dvbdev and dvbdevfops should
be freed just like when dvb_register_media_device() fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add the missing platform_device_unregister() before return
from zd1301_frontend_attach in the error handling case when
pdev->dev.driver is empty.
There's an error handling route named err_platform_device_unregister,
so just reuse it.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Smatch complains that "rc_proto" comes from the user and it can result
in shift wrapping in ir_raw_encode_scancode()
drivers/media/rc/rc-ir-raw.c:526 ir_raw_encode_scancode()
error: undefined (user controlled) shift '1 << protocol'
This is true, but I reviewed the surrounding code and it appears
harmless. Anyway, let's verify that "rc_proto" is valid as a kernel
hardening measure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
After the SMMU translation is disabled in the
arm-smmu shutdown callback during reboot, if
any subsystem are still alive then IOVAs they
are using will become PAs on bus, which may
lead to crash.
So implemented shutdown callback, which detach iommu maps.
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In concurrency usecase and reboot scenario we are seeing muliple
crashes related to iommu_map/iommu_unamp of core->fw.iommu_domain.
In one case we are seeing "Unable to handle kernel NULL pointer
dereference at virtual address 0000000000000008" crash, this is
because of core->fw.iommu_domain in venus_firmware_deinit() and
trying to map in venus_boot() during venus_sys_error_handler()
Call trace:
__iommu_map+0x4c/0x348
iommu_map+0x5c/0x70
venus_boot+0x184/0x230 [venus_core]
venus_sys_error_handler+0xa0/0x14c [venus_core]
process_one_work+0x210/0x3d0
worker_thread+0x248/0x3f4
kthread+0x11c/0x12c
ret_from_fork+0x10/0x18
In second case we are seeing "Unable to handle kernel paging request
at virtual address 006b6b6b6b6b6b9b" crash, this is because of
unmapping iommu domain which is already unmapped.
Call trace:
venus_remove+0xf8/0x108 [venus_core]
venus_core_shutdown+0x1c/0x34 [venus_core]
platform_drv_shutdown+0x28/0x34
device_shutdown+0x154/0x1fc
kernel_restart_prepare+0x40/0x4c
kernel_restart+0x1c/0x64
__arm64_sys_reboot+0x190/0x238
el0_svc_common+0xa4/0x154
el0_svc_compat_handler+0x2c/0x38
el0_svc_compat+0x8/0x10
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
For core ops we are having only write protect but there
is no read protect, because of this in multithreading
and concurrency, one CPU core is reading without wait
which is causing the NULL pointer dereferece crash.
one such scenario is as show below, where in one CPU
core, core->ops becoming NULL and in another CPU core
calling core->ops->session_init().
CPU: core-7:
Call trace:
hfi_session_init+0x180/0x1dc [venus_core]
vdec_queue_setup+0x9c/0x364 [venus_dec]
vb2_core_reqbufs+0x1e4/0x368 [videobuf2_common]
vb2_reqbufs+0x4c/0x64 [videobuf2_v4l2]
v4l2_m2m_reqbufs+0x50/0x84 [v4l2_mem2mem]
v4l2_m2m_ioctl_reqbufs+0x2c/0x38 [v4l2_mem2mem]
v4l_reqbufs+0x4c/0x5c
__video_do_ioctl+0x2b0/0x39c
CPU: core-0:
Call trace:
venus_shutdown+0x98/0xfc [venus_core]
venus_sys_error_handler+0x64/0x148 [venus_core]
process_one_work+0x210/0x3d0
worker_thread+0x248/0x3f4
kthread+0x11c/0x12c
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently in calculate_inst_freq(), video driver is calculating
macro blocks per frame instead of macro blocks per second(mpbs).
Which results frequency is always setting to lower frequency (150MHz)
as per frequency table for sc7180. Hence the playback is not smooth.
Corrected this by correcting the mbps calculation in calculate_inst_freq().
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As per current implementation, video driver is unvoting "videom-mem" path
for last video session during vdec_session_release().
While video playback when we try to suspend device, we see video clock
warnings since votes are already removed during vdec_session_release().
corrected this by putting dummy vote on "video-mem" after last video
session release and unvoting it during suspend.
suspend")
Fixes: 07f8f22a33a9e ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As per bandwidth table video driver is voting with average bandwidth
for "video-mem" and "cpu-cfg" paths as peak bandwidth is zero
in bandwidth table.
suspend")
Fixes: 07f8f22a33a9e ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently video driver is voting for venus0-ebi path during buffer
processing with an average bandwidth of all the instances and
unvoting during session release.
While video streaming when we try to do XO-SD using the command
"echo mem > /sys/power/state command" , device is not entering
to suspend state and from interconnect summary seeing votes for venus0-ebi
Corrected this by voting for venus0-ebi path in venus_runtime_resume()
and unvote during venus_runtime_suspend().
suspend")
Fixes: 07f8f22a33a9e ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently video driver is voting after clk enable and un voting
before clk disable. This is incorrect, video driver should vote
before clk enable and unvote after clk disable.
Corrected this by changing the order of clk enable and clk disable.
suspend")
Fixes: 07f8f22a33a9e ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Per the stateful codec specification, VIDIOC_G_SELECTION with a target
of V4L2_SEL_TGT_COMPOSE is supposed to return the crop area of capture
buffers containing the decoded frame. Until now the driver did not get
that information from the firmware and just returned the dimensions of
CAPTURE buffers.
The firmware unfortunately does not always provide the crop information
from the stream ; also make sure to detect when that happens and
fallback to providing the coded size in these cases.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The default codec after driver open is set to be H264 but the
instance format for capture is wrongly set to H263. Correct this
to H264.
For regular applications this is not a big issue because they set
the format through S_FMT but for example v4l2-compliance does not.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Some identifiers have different names between their prototypes
and the kernel-doc markup. Seome seems to be due to cut-and-paste
related issues.
Others need to be fixed, as kernel-doc markups should use this format:
identifier - description
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> # IPU3 and V4L2
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
mtk_jpeg_remove()
if mtk_jpeg_clk_init() succeed, mtk_jpeg_probe() and mtk_jpeg_remove()
doesn't have a corresponding put_device(). Thus add a new helper
mtk_jpeg_clk_release() to fix it.
Fixes: b2f0d2724ba4 ("[media] vcodec: mediatek: Add Mediatek JPEG Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Video engine in R40 is very similar to that in A33 but it runs on lower
speed, at least according to OS images released by board designer.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Allwinner R40 SoC contains video engine. Add compatible for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
To avoid potentially overflowing the kernel logs in the case
of corrupted streams, this commit replaces an error message with
a per-stream counter to be read through a driver-specific
control.
Applications can read the per-stream accumulated
error macroblocks count.
The old error message is replaced by a rate-limited debug message.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
It's possible that the VPU was initialized using just one buffer,
containing only codec headers.
In this case, right after the initialization and after updating
the FIFO read pointer, we need to iterate through all the coda_buffer_meta
and release any metas that have been already used by the VPU.
This issue is affecting indirectly the bitstream buffer fill
threshold, which depends on the meta end position of the first
queued meta, which is passed to coda_bitstream_can_fetch_past().
Without this fix, it's possible that for certain videos, the
bitstream buffer level is not filled properly, resulting in a PIC_RUN
timeout.
Reported-by: Benjamin Bara <benjamin.bara@skidata.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Set the code of the metadata pads of the isp entity to
MEDIA_BUS_FMT_METADATA_FIXED and set the width and
height of their formats to 0. This solves the TODO
item:
"Fix pad format size for statistics and parameters entities."
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
MEDIA_BUS_FMT_METADATA_FIXED should be used when
the same driver handles both sides of the link and
the bus format is a fixed metadata format that is
not configurable from userspace.
The width and height will be set to 0 for this format.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in cedrus_start_streaming. We should fix it.
Fixes: d5aecd289babf ("media: cedrus: Implement runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference imbalance in rkisp1_vb2_start_streaming, so we
should fix it.
Fixes: 56e3b29f9f6b2 ("media: staging: rkisp1: add streaming paths")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Simplify the return expression.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Commit 9495b7e92f71 ("driver core: platform: Initialize dma_parms for
platform devices") included dma_parms in platform_device. There's no need
to allocate again.
Fixes: 13483fc2f20f ("media: mtk-vcodec: set dma max segment size")
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
isif_probe() invokes iounmap() on error handling paths, but it does not
reset the global state. So, later it can invoke iounmap() even when
ioremap() fails. This is the case also for isif_remove(). The patch
resets the global state after invoking iounmap() to avoid this.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Remove Jason Chen's e-mail address for it no longer works.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Fix PCLK polarity not being taken into account.
Add comments about BT656 register control.
Remove useless ov5640_set_stream_bt656() function.
Refine comments about MIPI IO register control.
Fixes: 4039b03720f7 ("media: i2c: ov5640: Add support for BT656 mode")
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Use v4l2_get_link_freq helper and add support for sensor drivers
implementing only V4L2_CID_PIXEL_RATE.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add a helper for obtaining the link frequency from transmitter drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Raw camera sensors connected to parallel or CSI-2 busses need to implement
V4L2_CID_LINK_FREQ control so receiver drivers can configure the hardware
accordingly.
Document this. Also say V4L2_CID_PIXEL_RATE is recommended for such
hardware.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Remove extra "is" from sentence explaining V4L2_CID_PIXEL_RATE may be used
to tell the pixel rate used by a transmitter driver. Also call
V4L2_CID_PIXEL_RATE a control.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|