| Age | Commit message (Collapse) | Author |
|---|
|
i) RFC3810, 9.2. Query Interval [QI] says:
The Query Interval variable denotes the interval between General
Queries sent by the Querier. Default value: 125 seconds. [...]
ii) RFC3810, 9.3. Query Response Interval [QRI] says:
The Maximum Response Delay used to calculate the Maximum Response
Code inserted into the periodic General Queries. Default value:
10000 (10 seconds) [...] The number of seconds represented by the
[Query Response Interval] must be less than the [Query Interval].
iii) RFC3810, 9.12. Older Version Querier Present Timeout [OVQPT] says:
The Older Version Querier Present Timeout is the time-out for
transitioning a host back to MLDv2 Host Compatibility Mode. When an
MLDv1 query is received, MLDv2 hosts set their Older Version Querier
Present Timer to [Older Version Querier Present Timeout].
This value MUST be ([Robustness Variable] times (the [Query Interval]
in the last Query received)) plus ([Query Response Interval]).
Hence, on *default* the timeout results in:
[RV] = 2, [QI] = 125sec, [QRI] = 10sec
[OVQPT] = [RV] * [QI] + [QRI] = 260sec
Having that said, we currently calculate [OVQPT] (here given as 'switchback'
variable) as ...
switchback = (idev->mc_qrv + 1) * max_delay
RFC3810, 9.12. says "the [Query Interval] in the last Query received". In
section "9.14. Configuring timers", it is said:
This section is meant to provide advice to network administrators on
how to tune these settings to their network. Ambitious router
implementations might tune these settings dynamically based upon
changing characteristics of the network. [...]
iv) RFC38010, 9.14.2. Query Interval:
The overall level of periodic MLD traffic is inversely proportional
to the Query Interval. A longer Query Interval results in a lower
overall level of MLD traffic. The value of the Query Interval MUST
be equal to or greater than the Maximum Response Delay used to
calculate the Maximum Response Code inserted in General Query
messages.
I assume that was why switchback is calculated as is (3 * max_delay), although
this setting seems to be meant for routers only to configure their [QI]
interval for non-default intervals. So usage here like this is clearly wrong.
Concluding, the current behaviour in IPv6's multicast code is not conform
to the RFC as switch back is calculated wrongly. That is, it has a too small
value, so MLDv2 hosts switch back again to MLDv2 way too early, i.e. ~30secs
instead of ~260secs on default.
Hence, introduce necessary helper functions and fix this up properly as it
should be.
Introduced in 06da92283 ("[IPV6]: Add MLDv2 support."). Credits to Hannes
Frederic Sowa who also had a hand in this as well. Also thanks to Hangbin Liu
who did initial testing.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: David Stevens <dlstevens@us.ibm.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1b7fdd2ab585("tcp: do not use cached RTT for RTT estimation")
removes important comments on how RTO is initialized and updated.
Hopefully this patch puts those information back.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vxlan-udp-recv function lookup vxlan_sock struct on every packet
recv by using udp-port number. we can use sk->sk_user_data to
store vxlan_sock and avoid lookup.
I have open coded rcu-api to store and read vxlan_sock from
sk_user_data to avoid sparse warning as sk_user_data is not
__rcu pointer.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a nice helper to parse MAC. Let's use it and remove custom
implementation.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Time stamp binary rollover is set.
The synopsys spec says When TSCRLSSR is cleard, the rollover value of
sub-second register is 0x7FFFFFFF(0.465 ns per clock).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
multiple of 4
net: sctp: Fix data chunk fragmentation for MTU values which are not multiple of 4
Initially the problem was observed with ipsec, but later it became clear that
SCTP data chunk fragmentation algorithm has problems with MTU values which are
not multiple of 4. Test program was used which just transmits 2000 bytes long
packets to other host. tcpdump was used to observe re-fragmentation in IP layer
after SCTP already fragmented data chunks.
With MTU 1500:
12:54:34.082904 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 1500)
10.151.38.153.39303 > 10.151.24.91.54321: sctp (1) [DATA] (B) [TSN: 2366088589] [SID: 0] [SSEQ 1] [PPID 0x0]
12:54:34.082933 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 596)
10.151.38.153.39303 > 10.151.24.91.54321: sctp (1) [DATA] (E) [TSN: 2366088590] [SID: 0] [SSEQ 1] [PPID 0x0]
12:54:34.090576 IP (tos 0x2,ECT(0), ttl 63, id 0, offset 0, flags [DF], proto SCTP (132), length 48)
10.151.24.91.54321 > 10.151.38.153.39303: sctp (1) [SACK] [cum ack 2366088590] [a_rwnd 79920] [#gap acks 0] [#dup tsns 0]
With MTU 1499:
13:02:49.955220 IP (tos 0x2,ECT(0), ttl 64, id 48215, offset 0, flags [+], proto SCTP (132), length 1492)
10.151.38.153.39084 > 10.151.24.91.54321: sctp[|sctp]
13:02:49.955249 IP (tos 0x2,ECT(0), ttl 64, id 48215, offset 1472, flags [none], proto SCTP (132), length 28)
10.151.38.153 > 10.151.24.91: ip-proto-132
13:02:49.955262 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 600)
10.151.38.153.39084 > 10.151.24.91.54321: sctp (1) [DATA] (E) [TSN: 404355346] [SID: 0] [SSEQ 1] [PPID 0x0]
13:02:49.956770 IP (tos 0x2,ECT(0), ttl 63, id 0, offset 0, flags [DF], proto SCTP (132), length 48)
10.151.24.91.54321 > 10.151.38.153.39084: sctp (1) [SACK] [cum ack 404355346] [a_rwnd 79920] [#gap acks 0] [#dup tsns 0]
Here problem in data portion limit calculation leads to re-fragmentation in IP,
which is sub-optimal. The problem is max_data initial value, which doesn't take
into account the fact, that data chunk must be padded to 4-bytes boundary.
It's enough to correct max_data, because all later adjustments are correctly
aligned to 4-bytes boundary.
After the fix is applied, everything is fragmented correctly for uneven MTUs:
15:16:27.083881 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 1496)
10.151.38.153.53417 > 10.151.24.91.54321: sctp (1) [DATA] (B) [TSN: 3077098183] [SID: 0] [SSEQ 1] [PPID 0x0]
15:16:27.083907 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 600)
10.151.38.153.53417 > 10.151.24.91.54321: sctp (1) [DATA] (E) [TSN: 3077098184] [SID: 0] [SSEQ 1] [PPID 0x0]
15:16:27.085640 IP (tos 0x2,ECT(0), ttl 63, id 0, offset 0, flags [DF], proto SCTP (132), length 48)
10.151.24.91.54321 > 10.151.38.153.53417: sctp (1) [SACK] [cum ack 3077098184] [a_rwnd 79920] [#gap acks 0] [#dup tsns 0]
The bug was there for years already, but
- is a performance issue, the packets are still transmitted
- doesn't show up with default MTU 1500, but possibly with ipsec (MTU 1438)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Free_irq is not needed if there has been no request_irq. Free_irq is
removed from both the probe and remove functions. The correct request_irq
and free_irq are found in the open and close functions.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
*e = platform_get_irq(...);
... when != request_irq(e,...)
*free_irq(e,...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Solution:
=========
- Synchronize linux's `include/uapi/linux/in6.h'
with glibc's `inet/netinet/in.h'.
- Synchronize glibc's `inet/netinet/in.h with linux's
`include/uapi/linux/in6.h'.
- Allow including the headers in either other.
- First header included defines the structures and macros.
Details:
========
The kernel promises not to break the UAPI ABI so I don't
see why we can't just have the two userspace headers
coordinate?
If you include the kernel headers first you get those,
and if you include the glibc headers first you get those,
and the following patch arranges a coordination and
synchronization between the two.
Let's handle `include/uapi/linux/in6.h' from linux,
and `inet/netinet/in.h' from glibc and ensure they compile
in any order and preserve the required ABI.
These two patches pass the following compile tests:
cat >> test1.c <<EOF
int main (void) {
return 0;
}
EOF
gcc -c test1.c
cat >> test2.c <<EOF
int main (void) {
return 0;
}
EOF
gcc -c test2.c
One wrinkle is that the kernel has a different name for one of
the members in ipv6_mreq. In the kernel patch we create a macro
to cover the uses of the old name, and while that's not entirely
clean it's one of the best solutions (aside from an anonymous
union which has other issues).
I've reviewed the code and it looks to me like the ABI is
assured and everything matches on both sides.
Notes:
- You want netinet/in.h to include bits/in.h as early as possible,
but it needs in_addr so define in_addr early.
- You want bits/in.h included as early as possible so you can use
the linux specific code to define __USE_KERNEL_DEFS based on
the _UAPI_* macro definition and use those to cull in.h.
- glibc was missing IPPROTO_MH, added here.
Compile tested and inspected.
Reported-by: Thomas Backlund <tmb@mageia.org>
Cc: Thomas Backlund <tmb@mageia.org>
Cc: libc-alpha@sourceware.org
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Carlos O'Donell <carlos@redhat.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It upsets static analyzers when we don't check for allocation failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
This series contains updates to igb only.
Todd provides a fix for igb to not look for a PBA in the iNVM on
devices that are flashless.
Akeem provides igb patches to add a new PHY id for i354, as well as
a couple of patches to implement the new PHY id. He also provides
several patches to correctly report the appropriate media type as
well as correctly report advertised/supported link for i354 devices.
Lastly Akeem implements a 1 second delay mechanism for i210 devices
to avoid erroneous link issue with the link partner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
The following batch contains:
* Three fixes for the new synproxy target available in your
net-next tree, from Jesper D. Brouer and Patrick McHardy.
* One fix for TCPMSS to correctly handling the fragmentation
case, from Phil Oester. I'll pass this one to -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates igb driver version to 5.0.5
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes the way we report supported/advertised link for i354
devices, especially for 2.5 GB. Instead of reporting 2.5 GB for all i354
devices erroneously, check first, if it is 2.5 GB capable.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes how we get speed/duplex for non_copper devices; it
now uses pcs register to get current speed and duplex instead of using
generic status register that we use to detect speed/duplex for copper
devices.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit b396966c4 (netfilter: xt_TCPMSS: Fix missing fragmentation handling),
I attempted to add safe fragment handling to xt_TCPMSS. However, Andy Padavan
of Project N56U correctly points out that returning XT_CONTINUE in this
function does not work. The callers (tcpmss_tg[46]) expect to receive a value
of 0 in order to return XT_CONTINUE.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since i354 2.5Gb devices are not Copper media type but SerDes, so this
patch changes the way we detect speed/duplex link info for this device.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
PHY Power Management does not exist for i354 device. So, there is no
need to read and write this register or clear go link Disconnect bit,
which could cause a lot of issues.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch implements downshift mechanism for M88E1543 PHY, so that
downshift is disabled first during link setup process, and later enabled
if we are master and downshift link is negotiated. Also cleaned up
return code implementation.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes PHY_ID for i354 device, now using M88E1543
instead of M88E1545.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds 1 sec delay mechanism to i210 device family, in order
to avoid erroneous link issue with the link partner.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When a part is flashless, do not look for a PBA in the iNVM.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Packets reaching SYNPROXY were default dropped, as they were most
likely invalid (given the recommended state matching). This
patch, changes SYNPROXY target to let packets, not consumed,
continue being processed by the stack.
This will be more in line other target modules. As it will allow
more flexible configurations of handling, logging or matching on
packets in INVALID states.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
With CONFIG_NETFILTER_DEBUG we get the following warning during SYNPROXY init:
[ 80.558906] WARNING: CPU: 1 PID: 4833 at net/netfilter/nf_conntrack_extend.c:80 __nf_ct_ext_add_length+0x217/0x220 [nf_conntrack]()
The reason is that the conntrack template is set to confirmed before adding
the extension and it is invalid to add extensions to already confirmed
conntracks. Fix by adding the extensions before setting the conntrack to
confirmed.
Reported-by: Jesper Dangaard Brouer <jesper.brouer@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Its seems Patrick missed to incoorporate some of my requested changes
during review v2 of SYNPROXY netfilter module.
Which were, to avoid SYN+ACK packets to enter the path, meant for the
ACK packet from the client (from the 3WHS).
Further there were a bug in ip6t_SYNPROXY.c, for matching SYN packets
that didn't exclude the ACK flag.
Go a step further with SYN packet/flag matching by excluding flags
ACK+FIN+RST, in both IPv4 and IPv6 modules.
The intented usage of SYNPROXY is as follows:
(gracefully describing usage in commit)
iptables -t raw -A PREROUTING -i eth0 -p tcp --dport 80 --syn -j NOTRACK
iptables -A INPUT -i eth0 -p tcp --dport 80 -m state UNTRACKED,INVALID \
-j SYNPROXY --sack-perm --timestamp --mss 1480 --wscale 7 --ecn
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_loose
This does filter SYN flags early, for packets in the UNTRACKED state,
but packets in the INVALID state with other TCP flags could still
reach the module, thus this stricter flag matching is still needed.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
tcp_rcv_established() returns only one value namely 0. We change the return
value to void (as suggested by David Miller).
After commit 0c24604b (tcp: implement RFC 5961 4.2), we no longer send RSTs in
response to SYNs. We can remove the check and processing on the return value of
tcp_rcv_established().
We also fix jtcp_rcv_established() in tcp_probe.c to match that of
tcp_rcv_established().
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With recent changes in tcp_probe module (e.g. f925d0a62d ("net: tcp_probe:
add IPv6 support")) we also need to take into account that tbuf needs to
be updated as format string will be further expanded. tbuf sits on the stack
in tcpprobe_read() function that is invoked when user space reads procfs
file /proc/net/tcpprobe, hence not fast path as in jtcp_rcv_established().
Having a size similarly as in sctp_probe module of 256 bytes is fully
sufficient for that, we need theoretical maximum of 252 bytes otherwise we
could get truncated.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just remove a small semicolon.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes warning "warning: symbol 'qlcnic_set_dcb_ops' was
not declared. Should it be static?"
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was found with a manual audit and I don't have a reproducer. We
limit ->calling_len and ->called_len when we get them from
copy_from_user() in x25_ioctl() so when they come from skb->data then
we should cap them there as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"tty->name" and "name" are a 64 character buffers. My static checker
complains because we add the "cf" on the front so it look like we are
copying a 66 character string into a 64 character buffer.
Also if the name is larger than IFNAMSIZ (16) it triggers a BUG_ON()
inside the call to alloc_netdev().
This is all under CAP_SYS_ADMIN so it's not a security fix, it just adds
a little robustness.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hypervisor is big endian, so little endian kernel builds need
to byteswap.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Casting from 'void *' is unnecessary, because casting from 'void *'
to any pointer type is automatic.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use bp->pfid from bnx2x instead to avoid duplication.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use BP_PORT and chip_port_mode directly from bnx2x.h to avoid duplication.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
to avoid duplication of the same logic.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This eliminates duplication and ensures that all bnx2x chips will be
supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we're linking upper devices to lower ones, which results in
upside-down relationship: upper devices seeing lower devices via its upper
lists.
Fix this by correctly linking lower devices to the upper ones.
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The goal of this patch is to harmonize cleanup done on a skbuff on rx path.
Before this patch, behaviors were different depending of the tunnel type.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The goal of this patch is to harmonize cleanup done on a skbuff on xmit path.
Before this patch, behaviors were different depending of the tunnel type.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function was only used when a packet was sent to another netns. Now, it can
also be used after tunnel encapsulation or decapsulation.
Only skb_orphan() should not be done when a packet is not crossing netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This argument is not used, let's remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This argument is not used, let's remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bond_compute_features is always called with RTNL held, so we can safely
drop the read bond->lock.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We're protected by RTNL so nothing can happen and we can safely drop the
read bond->lock.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can drop the use of bond->lock for mutual exclusion in
bond_3ad_update_lacp_rate and use RTNL in the sysfs store function
instead. This way we'll prevent races with mode change and interface
up/down as well as simplify update_lacp_rate by removing the check for
port->slave because it'll always be initialized (done while enslaving
with RTNL). This change will also help in the future removal of reader
bond->lock from bond_enslave.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't have to release all slaves when closing the bond dev, so remove
the outdated comment and the braces around the left single statement.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch aims to remove a use of the bond->lock for mutual exclusion
which will later allow easier migration to RCU of the users of this
functionality. We use RTNL as a synchronizing mechanism since it's
always held when send_peer_notif is set, and when it is decremented from
the notifier function. We can also drop some locking, and fix the
leakage of the send_peer_notif counter.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Michael point out, We used to limit the max pending DMAs to get better cache
utilization. But it was not done correctly since it was one done when there's no
new buffers submitted from guest. Guest can easily exceeds the limitation by
keeping sending packets.
So this patch moves the check into main loop. Tests shows about 5%-10%
improvement on per cpu throughput for guest tx.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
