| Age | Commit message (Collapse) | Author |
|---|
|
If sb_occ_port_pool_get() failed in devlink_nl_sb_port_pool_fill(),
msg should be canceled by genlmsg_cancel().
Fixes: df38dafd2559 ("devlink: implement shared buffer occupancy monitoring interface")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20201113111622.11040-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the phy enables power saving technology, the dwmac's software reset
needs more time to complete, enlarge dma reset timeout to 200000us.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201113090902.5c7aab1a@xhacker.debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On arm imx6, when opening the chip's netdev, the whole Linux
kernel intermittently hangs/freezes.
This is caused by a bug in the driver code which tests if pcie
interrupts are working correctly, using the software interrupt:
1. open: enable the software interrupt
2. open: tell the chip to assert the software interrupt
3. open: wait for flag
4. ISR: acknowledge s/w interrupt, set flag
5. open: notice flag, disable the s/w interrupt, continue
Unfortunately the ISR only acknowledges the s/w interrupt, but
does not disable it. This will re-trigger the ISR in a tight
loop.
On some (lucky) platforms, open proceeds to disable the s/w
interrupt even while the ISR is 'spinning'. On arm imx6,
the spinning ISR does not allow open to proceed, resulting
in a hung Linux kernel.
Fix minimally by disabling the s/w interrupt in the ISR, which
will prevent it from spinning. This won't break anything because
the s/w interrupt is used as a one-shot interrupt.
Note that this is a minimal fix, overlooking many possible
cleanups, e.g.:
- lan743x_intr_software_isr() is completely redundant and reads
INT_STS twice for no apparent reason
- disabling the s/w interrupt in lan743x_intr_test_isr() is now
redundant, but harmless
- waiting on software_isr_flag can be converted from a sleeping
poll loop to wait_event_timeout()
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # arm imx6 lan7430
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201112204741.12375-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When running this chip on arm imx6, we intermittently observe
the following kernel warning in the log, especially when the
system is under high load:
[ 50.119484] ------------[ cut here ]------------
[ 50.124377] WARNING: CPU: 0 PID: 303 at kernel/softirq.c:169 __local_bh_enable_ip+0x100/0x184
[ 50.132925] IRQs not enabled as expected
[ 50.159250] CPU: 0 PID: 303 Comm: rngd Not tainted 5.7.8 #1
[ 50.164837] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 50.171395] [<c0111a38>] (unwind_backtrace) from [<c010be28>] (show_stack+0x10/0x14)
[ 50.179162] [<c010be28>] (show_stack) from [<c05b9dec>] (dump_stack+0xac/0xd8)
[ 50.186408] [<c05b9dec>] (dump_stack) from [<c0122e40>] (__warn+0xd0/0x10c)
[ 50.193391] [<c0122e40>] (__warn) from [<c0123238>] (warn_slowpath_fmt+0x98/0xc4)
[ 50.200892] [<c0123238>] (warn_slowpath_fmt) from [<c012b010>] (__local_bh_enable_ip+0x100/0x184)
[ 50.209860] [<c012b010>] (__local_bh_enable_ip) from [<bf09ecbc>] (destroy_conntrack+0x48/0xd8 [nf_conntrack])
[ 50.220038] [<bf09ecbc>] (destroy_conntrack [nf_conntrack]) from [<c0ac9b58>] (nf_conntrack_destroy+0x94/0x168)
[ 50.230160] [<c0ac9b58>] (nf_conntrack_destroy) from [<c0a4aaa0>] (skb_release_head_state+0xa0/0xd0)
[ 50.239314] [<c0a4aaa0>] (skb_release_head_state) from [<c0a4aadc>] (skb_release_all+0xc/0x24)
[ 50.247946] [<c0a4aadc>] (skb_release_all) from [<c0a4b4cc>] (consume_skb+0x74/0x17c)
[ 50.255796] [<c0a4b4cc>] (consume_skb) from [<c081a2dc>] (lan743x_tx_release_desc+0x120/0x124)
[ 50.264428] [<c081a2dc>] (lan743x_tx_release_desc) from [<c081a98c>] (lan743x_tx_napi_poll+0x5c/0x18c)
[ 50.273755] [<c081a98c>] (lan743x_tx_napi_poll) from [<c0a6b050>] (net_rx_action+0x118/0x4a4)
[ 50.282306] [<c0a6b050>] (net_rx_action) from [<c0101364>] (__do_softirq+0x13c/0x53c)
[ 50.290157] [<c0101364>] (__do_softirq) from [<c012b29c>] (irq_exit+0x150/0x17c)
[ 50.297575] [<c012b29c>] (irq_exit) from [<c0196a08>] (__handle_domain_irq+0x60/0xb0)
[ 50.305423] [<c0196a08>] (__handle_domain_irq) from [<c05d44fc>] (gic_handle_irq+0x4c/0x90)
[ 50.313790] [<c05d44fc>] (gic_handle_irq) from [<c0100ed4>] (__irq_usr+0x54/0x80)
[ 50.321287] Exception stack(0xecd99fb0 to 0xecd99ff8)
[ 50.326355] 9fa0: 1cf1aa74 00000001 00000001 00000000
[ 50.334547] 9fc0: 00000001 00000000 00000000 00000000 00000000 00000000 00004097 b6d17d14
[ 50.342738] 9fe0: 00000001 b6d17c60 00000000 b6e71f94 800b0010 ffffffff
[ 50.349364] irq event stamp: 2525027
[ 50.352955] hardirqs last enabled at (2525026): [<c0a6afec>] net_rx_action+0xb4/0x4a4
[ 50.360892] hardirqs last disabled at (2525027): [<c0d6d2fc>] _raw_spin_lock_irqsave+0x1c/0x50
[ 50.369517] softirqs last enabled at (2524660): [<c01015b4>] __do_softirq+0x38c/0x53c
[ 50.377446] softirqs last disabled at (2524693): [<c012b29c>] irq_exit+0x150/0x17c
[ 50.385027] ---[ end trace c0b571db4bc8087d ]---
The driver is calling dev_kfree_skb() from code inside a spinlock,
where h/w interrupts are disabled. This is forbidden, as documented
in include/linux/netdevice.h. The correct function to use
dev_kfree_skb_irq(), or dev_kfree_skb_any().
Fix by using the correct dev_kfree_skb_xxx() functions:
in lan743x_tx_release_desc():
called by lan743x_tx_release_completed_descriptors()
called by in lan743x_tx_napi_poll()
which holds a spinlock
called by lan743x_tx_release_all_descriptors()
called by lan743x_tx_close()
which can-sleep
conclusion: use dev_kfree_skb_any()
in lan743x_tx_xmit_frame():
which holds a spinlock
conclusion: use dev_kfree_skb_irq()
in lan743x_tx_close():
which can-sleep
conclusion: use dev_kfree_skb()
in lan743x_rx_release_ring_element():
called by lan743x_rx_close()
which can-sleep
called by lan743x_rx_open()
which can-sleep
conclusion: use dev_kfree_skb()
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201112185949.11315-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Static checking revealed that a previous fix to
netlbl_unlabel_staticlist() leaves a stack variable uninitialized,
this patches fixes that.
Fixes: 866358ec331f ("netlabel: fix our progress tracking in netlbl_unlabel_staticlist()")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Reviewed-by: James Morris <jamorris@linux.microsoft.com>
Link: https://lore.kernel.org/r/160530304068.15651.18355773009751195447.stgit@sifl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A call trace was found in Hangbin's Codenomicon testing with debug kernel:
[ 2615.981988] ODEBUG: free active (active state 0) object type: timer_list hint: sctp_generate_proto_unreach_event+0x0/0x3a0 [sctp]
[ 2615.995050] WARNING: CPU: 17 PID: 0 at lib/debugobjects.c:328 debug_print_object+0x199/0x2b0
[ 2616.095934] RIP: 0010:debug_print_object+0x199/0x2b0
[ 2616.191533] Call Trace:
[ 2616.194265] <IRQ>
[ 2616.202068] debug_check_no_obj_freed+0x25e/0x3f0
[ 2616.207336] slab_free_freelist_hook+0xeb/0x140
[ 2616.220971] kfree+0xd6/0x2c0
[ 2616.224293] rcu_do_batch+0x3bd/0xc70
[ 2616.243096] rcu_core+0x8b9/0xd00
[ 2616.256065] __do_softirq+0x23d/0xacd
[ 2616.260166] irq_exit+0x236/0x2a0
[ 2616.263879] smp_apic_timer_interrupt+0x18d/0x620
[ 2616.269138] apic_timer_interrupt+0xf/0x20
[ 2616.273711] </IRQ>
This is because it holds asoc when transport->proto_unreach_timer starts
and puts asoc when the timer stops, and without holding transport the
transport could be freed when the timer is still running.
So fix it by holding/putting transport instead for proto_unreach_timer
in transport, just like other timers in transport.
v1->v2:
- Also use sctp_transport_put() for the "out_unlock:" path in
sctp_generate_proto_unreach_event(), as Marcelo noticed.
Fixes: 50b5d6ad6382 ("sctp: Fix a race between ICMP protocol unreachable and connect()")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/102788809b554958b13b95d33440f5448113b8d6.1605331373.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before commit c0cfa2d8a788 ("vsock: add multi-transports support"),
if a G2H transport was loaded (e.g. virtio transport), every packets
was forwarded to the host, regardless of the destination CID.
The H2G transports implemented until then (vhost-vsock, VMCI) always
responded with an error, if the destination CID was not
VMADDR_CID_HOST.
From that commit, we are using the remote CID to decide which
transport to use, so packets with remote CID > VMADDR_CID_HOST(2)
are sent only through H2G transport. If no H2G is available, packets
are discarded directly in the guest.
Some use cases (e.g. Nitro Enclaves [1]) rely on the old behaviour
to implement sibling VMs communication, so we restore the old
behavior when no H2G is registered.
It will be up to the host to discard packets if the destination is
not the right one. As it was already implemented before adding
multi-transport support.
Tested with nested QEMU/KVM by me and Nitro Enclaves by Andra.
[1] Documentation/virt/ne_overview.rst
Cc: Jorgen Hansen <jhansen@vmware.com>
Cc: Dexuan Cui <decui@microsoft.com>
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Reported-by: Andra Paraschiv <andraprs@amazon.com>
Tested-by: Andra Paraschiv <andraprs@amazon.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20201112133837.34183-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As soon as you add the second port to a VLAN, all other port
membership configuration is overwritten with zeroes. The HW interprets
this as all ports being "unmodified members" of the VLAN.
In the simple case when all ports belong to the same VLAN, switching
will still work. But using multiple VLANs or trying to set multiple
ports as tagged members will not work.
On the 6352, doing a VTU GetNext op, followed by an STU GetNext op
will leave you with both the member- and state- data in the VTU/STU
data registers. But on the 6097 (which uses the same implementation),
the STU GetNext will override the information gathered from the VTU
GetNext.
Separate the two stages, parsing the result of the VTU GetNext before
doing the STU GetNext.
We opt to update the existing implementation for all applicable chips,
as opposed to creating a separate callback for 6097, because although
the previous implementation did work for (at least) 6352, the
datasheet does not mention the masking behavior.
Fixes: ef6fcea37f01 ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the missing clk_disable_unprepare() before return from
smsc_phy_probe() in the error handling case.
Fixes: bedd8d78aba3 ("net: phy: smsc: LAN8710/20: add phy refclk in support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605180239-1792-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
genlmsg_cancel() needs to be called in the error path of
inet6_fill_ifmcaddr and inet6_fill_ifacaddr to cancel
the message.
Fixes: 6ecf4c37eb3e ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201112080950.1476302-1-zhangqilong3@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, we may set the tunnel option flag when the size of metadata
is zero. For example, we set TUNNEL_GENEVE_OPT in the receive function
no matter the geneve option is present or not. As this may result in
issues on the tunnel flags consumers, this patch fixes the issue.
Related discussion:
* https://lore.kernel.org/netdev/1604448694-19351-1-git-send-email-yihung.wei@gmail.com/T/#u
Fixes: 256c87c17c53 ("net: check tunnel option type in tunnel flags")
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Link: https://lore.kernel.org/r/1605053800-74072-1-git-send-email-yihung.wei@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We always have to update the value of ret, otherwise the
error value may be the previous one.
Fixes: f6bd59526ca5 ("net: ethernet: ti: introduce am654 common platform time sync driver")
Signed-off-by: Wang Qing <wangqing@vivo.com>
[grygorii.strashko@ti.com: fix build warn, subj add fixes tag]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201112164541.3223-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 4c2703dfd7fa ("net: marvell: prestera: Add PCI interface support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Vadym Kochan <vadym.kochan@plvision.eu>
Acked-by: Vadym Kochan <vadym.kochan@plvision.eu>
Link: https://lore.kernel.org/r/20201113113236.71678-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Selecting VSC8575 as a MACSec PHY was not correct
The relevant datasheet can be found here:
- VSC8575: https://www.microchip.com/wwwproducts/en/VSC8575
History:
v1 -> v2:
- Corrected the sha in the "Fixes:" tag
Fixes: 1bbe0ecc2a1a ("net: phy: mscc: macsec initialization")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20201113091116.1102450-1-steen.hegelund@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 58956317c8de ("neighbor: Improve garbage collection")
guarantees neighbour table entries a five-second lifetime. Processes
which make heavy use of multicast can fill the neighour table with
multicast addresses in five seconds. At that point, neighbour entries
can't be GC-ed because they aren't five seconds old yet, the kernel
log starts to fill up with "neighbor table overflow!" messages, and
sends start to fail.
This patch allows multicast addresses to be thrown out before they've
lived out their five seconds. This makes room for non-multicast
addresses and makes messages to all addresses more reliable in these
circumstances.
Fixes: 58956317c8de ("neighbor: Improve garbage collection")
Signed-off-by: Jeff Dike <jdike@akamai.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201113015815.31397-1-jdike@akamai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Depending on the SoC/platform the CPSW can completely lose context after a
suspend/resume cycle, including CPSW wrapper (WR) which will cause reset of
WR_C0_MISC_EN register, so CPTS IRQ will became disabled.
Fix it by moving CPTS IRQ enabling in cpsw_ndo_open() where CPTS is
actually started.
Fixes: 84ea9c0a95d7 ("net: ethernet: ti: cpsw: enable cpts irq")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201112111546.20343-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A handful of fixes:
* a use-after-free fix in rfkill
* a memory leak fix in the mac80211 TX status path
* some rate scaling fixes
* a fix for the often-reported (by syzbot) sleeping
in atomic issue with mac80211's station removal
* tag 'mac80211-for-net-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211:
mac80211: free sta in sta_info_insert_finish() on errors
mac80211: minstrel: fix tx status processing corner case
mac80211: minstrel: remove deferred sampling code
mac80211: fix memory leak on filtered powersave frames
rfkill: Fix use-after-free in rfkill_resume()
====================
Link: https://lore.kernel.org/r/20201113093421.24025-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If sta_info_insert_finish() fails, we currently keep the station
around and free it only in the caller, but there's only one such
caller and it always frees it immediately.
As syzbot found, another consequence of this split is that we can
put things that sleep only into __cleanup_single_sta() and not in
sta_info_free(), but this is the only place that requires such of
sta_info_free() now.
Change this to free the station in sta_info_insert_finish(), in
which case we can still sleep. This will also let us unify the
cleanup code later.
Cc: stable@vger.kernel.org
Fixes: dcd479e10a05 ("mac80211: always wind down STA state")
Reported-by: syzbot+32c6c38c4812d22f2f0b@syzkaller.appspotmail.com
Reported-by: syzbot+4c81fe92e372d26c4246@syzkaller.appspotmail.com
Reported-by: syzbot+6a7fe9faf0d1d61bc24a@syzkaller.appspotmail.com
Reported-by: syzbot+abed06851c5ffe010921@syzkaller.appspotmail.com
Reported-by: syzbot+b7aeb9318541a1c709f1@syzkaller.appspotmail.com
Reported-by: syzbot+d5a9416c6cafe53b5dd0@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20201112112201.ee6b397b9453.I9c31d667a0ea2151441cc64ed6613d36c18a48e0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The x25_disconnect function in x25_subr.c would decrease the refcount of
"x25->neighbour" (struct x25_neigh) and reset this pointer to NULL.
However, the x25_rx_call_request function in af_x25.c, which is called
when we receive a connection request, does not increase the refcount when
it assigns the pointer.
Fix this issue by increasing the refcount of "struct x25_neigh" in
x25_rx_call_request.
This patch fixes frequent kernel crashes when using AF_X25 sockets.
Fixes: 4becb7ee5b3d ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect")
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201112103506.5875-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 8c7bd5a454ff ("net: ethernet: mtk-star-emac: new driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/1605180879-2573-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ndo_start_xmit() method must return NETDEV_TX_OK if the DMA mapping
fails, after freeing the socket buffer.
Fix the mtk_star_netdev_start_xmit() function accordingly.
Fixes: 8c7bd5a454ff ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201112084833.21842-1-vincent.stehle@laposte.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a user unbinds and re-binds a NC-SI aware driver the kernel will
attempt to register the netlink interface at runtime. The structure is
marked __ro_after_init so registration fails spectacularly at this point.
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/bind
ftgmac100 1e660000.ethernet: Read MAC address 52:54:00:12:34:56 from chip
ftgmac100 1e660000.ethernet: Using NCSI interface
8<--- cut here ---
Unable to handle kernel paging request at virtual address 80a8f858
pgd = 8c768dd6
[80a8f858] *pgd=80a0841e(bad)
Internal error: Oops: 80d [#1] SMP ARM
CPU: 0 PID: 116 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00003-gdd25b227ec1e #51
Hardware name: Generic DT based system
PC is at genl_register_family+0x1f8/0x6d4
LR is at 0xff26ffff
pc : [<8073f930>] lr : [<ff26ffff>] psr: 20000153
sp : 8553bc80 ip : 81406244 fp : 8553bd04
r10: 8085d12c r9 : 80a8f73c r8 : 85739000
r7 : 00000017 r6 : 80a8f860 r5 : 80c8ab98 r4 : 80a8f858
r3 : 00000000 r2 : 00000000 r1 : 81406130 r0 : 00000017
Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
Control: 00c5387d Table: 85524008 DAC: 00000051
Process sh (pid: 116, stack limit = 0x1f1988d6)
...
Backtrace:
[<8073f738>] (genl_register_family) from [<80860ac0>] (ncsi_init_netlink+0x20/0x48)
r10:8085d12c r9:80c8fb0c r8:85739000 r7:00000000 r6:81218000 r5:85739000
r4:8121c000
[<80860aa0>] (ncsi_init_netlink) from [<8085d740>] (ncsi_register_dev+0x1b0/0x210)
r5:8121c400 r4:8121c000
[<8085d590>] (ncsi_register_dev) from [<805a8060>] (ftgmac100_probe+0x6e0/0x778)
r10:00000004 r9:80950228 r8:8115bc10 r7:8115ab00 r6:9eae2c24 r5:813b6f88
r4:85739000
[<805a7980>] (ftgmac100_probe) from [<805355ec>] (platform_drv_probe+0x58/0xa8)
r9:80c76bb0 r8:00000000 r7:80cd4974 r6:80c76bb0 r5:8115bc10 r4:00000000
[<80535594>] (platform_drv_probe) from [<80532d58>] (really_probe+0x204/0x514)
r7:80cd4974 r6:00000000 r5:80cd4868 r4:8115bc10
Jakub pointed out that ncsi_register_dev is obviously broken, because
there is only one family so it would never work if there was more than
one ncsi netdev.
Fix the crash by registering the netlink family once on boot, and drop
the code to unregister it.
Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Link: https://lore.kernel.org/r/20201112061210.914621-1-joel@jms.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release - regressions:
- arm64: dts: fsl-ls1028a-kontron-sl28: specify in-band mode for
ENETC
Current release - bugs in new features:
- mptcp: provide rmem[0] limit offset to fix oops
Previous release - regressions:
- IPv6: Set SIT tunnel hard_header_len to zero to fix path MTU
calculations
- lan743x: correctly handle chips with internal PHY
- bpf: Don't rely on GCC __attribute__((optimize)) to disable GCSE
- mlx5e: Fix VXLAN port table synchronization after function reload
Previous release - always broken:
- bpf: Zero-fill re-used per-cpu map element
- fix out-of-order UDP packets when forwarding with UDP GSO fraglists
turned on:
- fix UDP header access on Fast/frag0 UDP GRO
- fix IP header access and skb lookup on Fast/frag0 UDP GRO
- ethtool: netlink: add missing netdev_features_change() call
- net: Update window_clamp if SOCK_RCVBUF is set
- igc: Fix returning wrong statistics
- ch_ktls: fix multiple leaks and corner cases in Chelsio TLS offload
- tunnels: Fix off-by-one in lower MTU bounds for ICMP/ICMPv6 replies
- r8169: disable hw csum for short packets on all chip versions
- vrf: Fix fast path output packet handling with async Netfilter
rules"
* tag 'net-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
lan743x: fix use of uninitialized variable
net: udp: fix IP header access and skb lookup on Fast/frag0 UDP GRO
net: udp: fix UDP header access on Fast/frag0 UDP GRO
devlink: Avoid overwriting port attributes of registered port
vrf: Fix fast path output packet handling with async Netfilter rules
cosa: Add missing kfree in error path of cosa_write
net: switch to the kernel.org patchwork instance
ch_ktls: stop the txq if reaches threshold
ch_ktls: tcb update fails sometimes
ch_ktls/cxgb4: handle partial tag alone SKBs
ch_ktls: don't free skb before sending FIN
ch_ktls: packet handling prior to start marker
ch_ktls: Correction in middle record handling
ch_ktls: missing handling of header alone
ch_ktls: Correction in trimmed_len calculation
cxgb4/ch_ktls: creating skbs causes panic
ch_ktls: Update cheksum information
ch_ktls: Correction in finding correct length
cxgb4/ch_ktls: decrypted bit is not enough
net/x25: Fix null-ptr-deref in x25_connect
...
|
|
Pull NFS client bugfixes from Anna Schumaker:
"Stable fixes:
- Fix failure to unregister shrinker
Other fixes:
- Fix unnecessary locking to clear up some contention
- Fix listxattr receive buffer size
- Fix default mount options for nfsroot"
* tag 'nfs-for-5.10-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Remove unnecessary inode lock in nfs_fsync_dir()
NFS: Remove unnecessary inode locking in nfs_llseek_dir()
NFS: Fix listxattr receive buffer size
NFSv4.2: fix failure to unregister shrinker
nfsroot: Default mount option should ask for built-in NFS version
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These are mostly docmentation fixes and janitorial changes plus some
new device IDs and a new quirk.
Specifics:
- Fix documentation regarding GPIO properties (Andy Shevchenko)
- Fix spelling mistakes in ACPI documentation (Flavio Suligoi)
- Fix white space inconsistencies in ACPI code (Maximilian Luz)
- Fix string formatting in the ACPI Generic Event Device (GED) driver
(Nick Desaulniers)
- Add Intel Alder Lake device IDs to the ACPI drivers used by the
Dynamic Platform and Thermal Framework (Srinivas Pandruvada)
- Add lid-related DMI quirk for Medion Akoya E2228T to the ACPI
button driver (Hans de Goede)"
* tag 'acpi-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: DPTF: Support Alder Lake
Documentation: ACPI: fix spelling mistakes
ACPI: button: Add DMI quirk for Medion Akoya E2228T
ACPI: GED: fix -Wformat
ACPI: Fix whitespace inconsistencies
ACPI: scan: Fix acpi_dma_configure_id() kerneldoc name
Documentation: firmware-guide: gpio-properties: Clarify initial output state
Documentation: firmware-guide: gpio-properties: active_low only for GpioIo()
Documentation: firmware-guide: gpio-properties: Fix factual mistakes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Make the intel_pstate driver behave as expected when it operates in
the passive mode with HWP enabled and the 'powersave' governor on top
of it"
* tag 'pm-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Take CPUFREQ_GOV_STRICT_TARGET into account
cpufreq: Add strict_target to struct cpufreq_policy
cpufreq: Introduce CPUFREQ_GOV_STRICT_TARGET
cpufreq: Introduce governor flags
|
|
When no devicetree is present, the driver will use an
uninitialized variable.
Fix by initializing this variable.
Fixes: 902a66e08cea ("lan743x: correctly handle chips with internal PHY")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201112152513.1941-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Alexander Lobakin says:
====================
net: udp: fix Fast/frag0 UDP GRO
While testing UDP GSO fraglists forwarding through driver that uses
Fast GRO (via napi_gro_frags()), I was observing lots of out-of-order
iperf packets:
[ ID] Interval Transfer Bitrate Jitter
[SUM] 0.0-40.0 sec 12106 datagrams received out-of-order
Simple switch to napi_gro_receive() or any other method without frag0
shortcut completely resolved them.
I've found two incorrect header accesses in GRO receive callback(s):
- udp_hdr() (instead of udp_gro_udphdr()) that always points to junk
in "fast" mode and could probably do this in "regular".
This was the actual bug that caused all out-of-order delivers;
- udp{4,6}_lib_lookup_skb() -> ip{,v6}_hdr() (instead of
skb_gro_network_header()) that potentionally might return odd
pointers in both modes.
Each patch addresses one of these two issues.
This doesn't cover a support for nested tunnels as it's out of the
subject and requires more invasive changes. It will be handled
separately in net-next series.
Credits:
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Willem de Bruijn <willemb@google.com>
Since v4 [0]:
- split the fix into two logical ones (Willem);
- replace ternaries with plain ifs to beautify the code (Jakub);
- drop p->data part to reintroduce it later in abovementioned set.
Since v3 [1]:
- restore the original {,__}udp{4,6}_lib_lookup_skb() and use
private versions of them inside GRO code (Willem).
Since v2 [2]:
- dropped redundant check introduced in v2 as it's performed right
before (thanks to Eric);
- udp_hdr() switched to data + off for skbs from list (also Eric);
- fixed possible malfunction of {,__}udp{4,6}_lib_lookup_skb() with
Fast/frag0 due to ip{,v6}_hdr() usage (Willem).
Since v1 [3]:
- added a NULL pointer check for "uh" as suggested by Willem.
[0] https://lore.kernel.org/netdev/Ha2hou5eJPcblo4abjAqxZRzIl1RaLs2Hy0oOAgFs@cp4-web-036.plabs.ch
[1] https://lore.kernel.org/netdev/MgZce9htmEtCtHg7pmWxXXfdhmQ6AHrnltXC41zOoo@cp7-web-042.plabs.ch
[2] https://lore.kernel.org/netdev/0eaG8xtbtKY1dEKCTKUBubGiC9QawGgB3tVZtNqVdY@cp4-web-030.plabs.ch
[3] https://lore.kernel.org/netdev/YazU6GEzBdpyZMDMwJirxDX7B4sualpDG68ADZYvJI@cp4-web-034.plabs.ch
====================
Link: https://lore.kernel.org/r/hjGOh0iCOYyo1FPiZh6TMXcx3YCgNs1T1eGKLrDz8@cp4-web-037.plabs.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
udp{4,6}_lib_lookup_skb() use ip{,v6}_hdr() to get IP header of the
packet. While it's probably OK for non-frag0 paths, this helpers
will also point to junk on Fast/frag0 GRO when all headers are
located in frags. As a result, sk/skb lookup may fail or give wrong
results. To support both GRO modes, skb_gro_network_header() might
be used. To not modify original functions, add private versions of
udp{4,6}_lib_lookup_skb() only to perform correct sk lookups on GRO.
Present since the introduction of "application-level" UDP GRO
in 4.7-rc1.
Misc: replace totally unneeded ternaries with plain ifs.
Fixes: a6024562ffd7 ("udp: Add GRO functions to UDP socket")
Suggested-by: Willem de Bruijn <willemb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
UDP GRO uses udp_hdr(skb) in its .gro_receive() callback. While it's
probably OK for non-frag0 paths (when all headers or even the entire
frame are already in skb head), this inline points to junk when
using Fast GRO (napi_gro_frags() or napi_gro_receive() with only
Ethernet header in skb head and all the rest in the frags) and breaks
GRO packet compilation and the packet flow itself.
To support both modes, skb_gro_header_fast() + skb_gro_header_slow()
are typically used. UDP even has an inline helper that makes use of
them, udp_gro_udphdr(). Use that instead of troublemaking udp_hdr()
to get rid of the out-of-order delivers.
Present since the introduction of plain UDP GRO in 5.0-rc1.
Fixes: e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-11-10
This series contains updates to i40e and igc drivers and the MAINTAINERS
file.
Slawomir fixes updating VF MAC addresses to fix various issues related
to reporting and setting of these addresses for i40e.
Dan Carpenter fixes a possible used before being initialized issue for
i40e.
Vinicius fixes reporting of netdev stats for igc.
Tony updates repositories for Intel Ethernet Drivers.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
MAINTAINERS: Update repositories for Intel Ethernet Drivers
igc: Fix returning wrong statistics
i40e, xsk: uninitialized variable in i40e_clean_rx_irq_zc()
i40e: Fix MAC address setting for a VF via Host/VM
====================
Link: https://lore.kernel.org/r/20201111001955.533210-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cited commit in fixes tag overwrites the port attributes for the
registered port.
Avoid such error by checking registered flag before setting attributes.
Fixes: 71ad8d55f8e5 ("devlink: Replace devlink_port_attrs_set parameters with a struct")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20201111034744.35554-1-parav@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VRF devices use an optimized direct path on output if a default qdisc
is involved, calling Netfilter hooks directly. This path, however, does
not consider Netfilter rules completing asynchronously, such as with
NFQUEUE. The Netfilter okfn() is called for asynchronously accepted
packets, but the VRF never passes that packet down the stack to send
it out over the slave device. Using the slower redirect path for this
seems not feasible, as we do not know beforehand if a Netfilter hook
has asynchronously completing rules.
Fix the use of asynchronously completing Netfilter rules in OUTPUT and
POSTROUTING by using a special completion function that additionally
calls dst_output() to pass the packet down the stack. Also, slightly
adjust the use of nf_reset_ct() so that is called in the asynchronous
case, too.
Fixes: dcdd43c41e60 ("net: vrf: performance improvements for IPv4")
Fixes: a9ec54d1b0cd ("net: vrf: performance improvements for IPv6")
Signed-off-by: Martin Willi <martin@strongswan.org>
Link: https://lore.kernel.org/r/20201106073030.3974927-1-martin@strongswan.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nfs_inc_stats() is already thread-safe, and there are no other reasons
to hold the inode lock here.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Remove the contentious inode lock, and instead provide thread safety
using the file->f_lock spinlock.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Certain NFSv4.2/RDMA tests fail with v5.9-rc1.
rpcrdma_convert_kvec() runs off the end of the rl_segments array
because rq_rcv_buf.tail[0].iov_len holds a very large positive
value. The resultant kernel memory corruption is enough to crash
the client system.
Callers of rpc_prepare_reply_pages() must reserve an extra XDR_UNIT
in the maximum decode size for a possible XDR pad of the contents
of the xdr_buf's pages. That guarantees the allocated receive buffer
will be large enough to accommodate the usual contents plus that XDR
pad word.
encode_op_hdr() cannot add that extra word. If it does,
xdr_inline_pages() underruns the length of the tail iovec.
Fixes: 3e1f02123fba ("NFSv4.2: add client side XDR handling for extended attributes")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
We forgot to unregister the nfs4_xattr_large_entry_shrinker.
That leaves the global list of shrinkers corrupted after unload of the
nfs module, after which possibly unrelated code that calls
register_shrinker() or unregister_shrinker() gets a BUG() with
"supervisor write access in kernel mode".
And similarly for the nfs4_xattr_large_entry_lru.
Reported-by: Kris Karas <bugs-a17@moonlit-rail.com>
Tested-By: Kris Karas <bugs-a17@moonlit-rail.com>
Fixes: 95ad37f90c33 "NFSv4.2: add client side xattr caching."
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
* acpi-scan:
ACPI: scan: Fix acpi_dma_configure_id() kerneldoc name
* acpi-misc:
ACPI: GED: fix -Wformat
ACPI: Fix whitespace inconsistencies
* acpi-button:
ACPI: button: Add DMI quirk for Medion Akoya E2228T
* acpi-dptf:
ACPI: DPTF: Support Alder Lake
|
|
Some drivers fill the status rate list without setting the rate index after
the final rate to -1. minstrel_ht already deals with this, but minstrel
doesn't, which causes it to get stuck at the lowest rate on these drivers.
Fix this by checking the count as well.
Cc: stable@vger.kernel.org
Fixes: cccf129f820e ("mac80211: add the 'minstrel' rate control algorithm")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201111183359.43528-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Deferring sampling attempts to the second stage has some bad interactions
with drivers that process the rate table in hardware and use the probe flag
to indicate probing packets (e.g. most mt76 drivers). On affected drivers
it can lead to probing not working at all.
If the link conditions turn worse, it might not be such a good idea to
do a lot of sampling for lower rates in this case.
Fix this by simply skipping the sample attempt instead of deferring it,
but keep the checks that would allow it to be sampled if it was skipped
too often, but only if it has less than 95% success probability.
Also ensure that IEEE80211_TX_CTL_RATE_CTRL_PROBE is set for all probing
packets.
Cc: stable@vger.kernel.org
Fixes: cccf129f820e ("mac80211: add the 'minstrel' rate control algorithm")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201111183359.43528-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
After the status rework, ieee80211_tx_status_ext is leaking un-acknowledged
packets for stations in powersave mode.
To fix this, move the code handling those packets from __ieee80211_tx_status
into ieee80211_tx_status_ext
Reported-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Fixes: 3318111cf63d ("mac80211: reduce duplication in tx status functions")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201111183359.43528-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If a device is getting removed or reprobed during resume, use-after-free
might happen. For example, h5_btrtl_resume() schedules a work queue for
device reprobing, which of course requires removal first.
If the removal happens in parallel with the device_resume() and wins the
race to acquire device_lock(), removal may remove the device from the PM
lists and all, but device_resume() is already running and will continue
when the lock can be acquired, thus calling rfkill_resume().
During this, if rfkill_set_block() is then called after the corresponding
*_unregister() and kfree() are called, there will be an use-after-free
in hci_rfkill_set_block():
BUG: KASAN: use-after-free in hci_rfkill_set_block+0x58/0xc0 [bluetooth]
...
Call trace:
dump_backtrace+0x0/0x154
show_stack+0x20/0x2c
dump_stack+0xbc/0x12c
print_address_description+0x88/0x4b0
__kasan_report+0x144/0x168
kasan_report+0x10/0x18
check_memory_region+0x19c/0x1ac
__kasan_check_write+0x18/0x24
hci_rfkill_set_block+0x58/0xc0 [bluetooth]
rfkill_set_block+0x9c/0x120
rfkill_resume+0x34/0x70
dpm_run_callback+0xf0/0x1f4
device_resume+0x210/0x22c
Fix this by checking rfkill->registered in rfkill_resume(). device_del()
in rfkill_unregister() requires device_lock() and the whole rfkill_resume()
is also protected by the same lock via device_resume(), we can make sure
either the rfkill->registered is false before rfkill_resume() starts or the
rfkill device won't be unregistered before rfkill_resume() returns.
As async_resume() holds a reference to the device, at this level there can
be no use-after-free; only in the user that doesn't expect this scenario.
Fixes: 8589086f4efd ("Bluetooth: hci_h5: Turn off RTL8723BS on suspend, reprobe on resume")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201110084908.219088-1-tientzu@chromium.org
[edit commit message for clarity and add more info provided later]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If memory allocation for 'kbuf' succeed, cosa_write() doesn't have a
corresponding kfree() in exception handling. Thus add kfree() for this
function implementation.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Link: https://lore.kernel.org/r/20201110144614.43194-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move to the kernel.org patchwork instance, it has significantly
lower latency for accessing from Europe and the US. Other quirks
include the reply bot.
Link: https://lore.kernel.org/r/20201110035120.642746-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rohit Maheshwari says:
====================
cxgb4/ch_ktls: Fixes in nic tls code
This series helps in fixing multiple nic ktls issues. Series is broken
into 12 patches.
Patch 1 avoids deciding tls packet based on decrypted bit. If its a
retransmit packet which has tls handshake and finish (for encryption),
decrypted bit won't be set there, and so we can't rely on decrypted
bit.
Patch 2 helps supporting linear skb. SKBs were assumed non-linear.
Corrected the length extraction.
Patch 3 fixes the checksum offload update in WR.
Patch 4 fixes kernel panic happening due to creating new skb for each
record. As part of fix driver will use same skb to send out one tls
record (partial data) of the same SKB.
Patch 5 fixes the problem of skb data length smaller than remaining data
of the record.
Patch 6 fixes the handling of SKBs which has tls header alone pkt, but
not starting from beginning.
Patch 7 avoids sending extra data which is used to make a record 16 byte
aligned. We don't need to retransmit those extra few bytes.
Patch 8 handles the cases where retransmit packet has tls starting
exchanges which are prior to tls start marker.
Patch 9 fixes the problem os skb free before HW knows about tcp FIN.
Patch 10 handles the small packet case which has partial TAG bytes only.
HW can't handle those, hence using sw crypto for such pkts.
Patch 11 corrects the potential tcb update problem.
Patch 12 stops the queue if queue reaches threshold value.
v1->v2:
- Corrected fixes tag issue.
- Marked chcr_ktls_sw_fallback() static.
v2->v3:
- Replaced GFP_KERNEL with GFP_ATOMIC.
- Removed mixed fixes.
v3->v4:
- Corrected fixes tag issue.
v4->v5:
- Separated mixed fixes from patch 4.
v5-v6:
- Fixes tag should be at the end.
====================
Link: https://lore.kernel.org/r/20201109105142.15398-1-rohitm@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stop the queue and ask for the credits if queue reaches to
threashold.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
context id and port id should be filled while sending tcb update.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If TCP congestion caused a very small packets which only has some
part fo the TAG, and that too is not till the end. HW can't handle
such case, so falling back to sw crypto in such cases.
v1->v2:
- Marked chcr_ktls_sw_fallback() static.
Fixes: dc05f3df8fac ("chcr: Handle first or middle part of record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
