| Age | Commit message (Collapse) | Author |
|---|
|
If a record starts in middle, reset TCB UNA so that we could
avoid sending out extra packet which is needed to make it 16
byte aligned to start AES CTR.
Check also considers prev_seq, which should be what is
actually sent, not the skb data length.
Avoid updating partial TAG to HW at any point of time, that's
why we need to check if remaining part is smaller than TAG
size, then reset TX_MAX to be TAG starting sequence number.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If an skb has only header part which doesn't start from
beginning, is not being handled properly.
Fixes: dc05f3df8fac ("chcr: Handle first or middle part of record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
trimmed length calculation goes wrong if skb has only tag part
to send. It should be zero if there is no data bytes apart from
TAG.
Fixes: dc05f3df8fac ("chcr: Handle first or middle part of record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Creating SKB per tls record and freeing the original one causes
panic. There will be race if connection reset is requested. By
freeing original skb, refcnt will be decremented and that means,
there is no pending record to send, and so tls_dev_del will be
requested in control path while SKB of related connection is in
queue.
Better approach is to use same SKB to send one record (partial
data) at a time. We still have to create a new SKB when partial
last part of a record is requested.
This fix introduces new API cxgb4_write_partial_sgl() to send
partial part of skb. Present cxgb4_write_sgl can only provide
feasibility to start from an offset which limits to header only
and it can write sgls for the whole skb len. But this new API
will help in both. It can start from any offset and can end
writing in middle of the skb.
v4->v5:
- Removed extra changes.
Fixes: 429765a149f1 ("chcr: handle partial end part of a record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Checksum update was missing in the WR.
Fixes: 429765a149f1 ("chcr: handle partial end part of a record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a possibility of linear skbs coming in. Correcting
the length extraction logic.
v2->v3:
- Separated un-related changes from this patch.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If skb has retransmit data starting before start marker, e.g. ccs,
decrypted bit won't be set for that, and if it has some data to
encrypt, then it must be given to crypto ULD. So in place of
decrypted, check if socket is tls offloaded. Also, unless skb has
some data to encrypt, no need to give it for tls offload handling.
v2->v3:
- Removed ifdef.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This fixes a regression for blocking connects introduced by commit
4becb7ee5b3d ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect").
The x25->neighbour is already set to "NULL" by x25_disconnect() now,
while a blocking connect is waiting in
x25_wait_for_connection_establishment(). Therefore x25->neighbour must
not be accessed here again and x25->state is also already set to
X25_STATE_0 by x25_disconnect().
Fixes: 4becb7ee5b3d ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201109065449.9014-1-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX") the
network port of the Kontron sl28 board is broken. After the migration to
phylink the device tree has to specify the in-band-mode property. Add
it.
Fixes: 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201109110436.5906-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
kmemleak report a memory leak as follows:
unreferenced object 0xffff88810a596800 (size 512):
comm "ip", pid 21558, jiffies 4297568990 (age 112.120s)
hex dump (first 32 bytes):
00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N..........
ff ff ff ff ff ff ff ff 00 83 60 b0 ff ff ff ff ..........`.....
backtrace:
[<0000000022bbe21f>] tipc_topsrv_init_net+0x1f3/0xa70
[<00000000fe15ddf7>] ops_init+0xa8/0x3c0
[<00000000138af6f2>] setup_net+0x2de/0x7e0
[<000000008c6807a3>] copy_net_ns+0x27d/0x530
[<000000006b21adbd>] create_new_namespaces+0x382/0xa30
[<00000000bb169746>] unshare_nsproxy_namespaces+0xa1/0x1d0
[<00000000fe2e42bc>] ksys_unshare+0x39c/0x780
[<0000000009ba3b19>] __x64_sys_unshare+0x2d/0x40
[<00000000614ad866>] do_syscall_64+0x56/0xa0
[<00000000a1b5ca3c>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
'srv' is malloced in tipc_topsrv_start() but not free before
leaving from the error handling cases. We need to free it.
Fixes: 5c45ab24ac77 ("tipc: make struct tipc_server private for server.c")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20201109140913.47370-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb fixes from Konrad Rzeszutek Wilk:
"Two tiny fixes for issues that make drivers under Xen unhappy under
certain conditions"
* 'stable/for-linus-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: remove the tbl_dma_addr argument to swiotlb_tbl_map_single
swiotlb: fix "x86: Don't panic if can not alloc buffer for swiotlb"
|
|
Julian Wiedmann says:
====================
net/iucv: fixes 2020-11-09
One fix in the shutdown path for af_iucv sockets. This is relevant for
stable as well.
Also sending along an update for the Maintainers file.
v1 -> v2: use the correct Fixes tag in patch 1 (Jakub)
====================
Link: https://lore.kernel.org/r/20201109075706.56573-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I am retiring soon. Thus this patch removes myself from the
MAINTAINERS file (s390 network).
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
[jwi: fix up the subject]
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported the following KASAN finding:
BUG: KASAN: nullptr-dereference in iucv_send_ctrl+0x390/0x3f0 net/iucv/af_iucv.c:385
Read of size 2 at addr 000000000000021e by task syz-executor907/519
CPU: 0 PID: 519 Comm: syz-executor907 Not tainted 5.9.0-syzkaller-07043-gbcf9877ad213 #0
Hardware name: IBM 3906 M04 701 (KVM/Linux)
Call Trace:
[<00000000c576af60>] unwind_start arch/s390/include/asm/unwind.h:65 [inline]
[<00000000c576af60>] show_stack+0x180/0x228 arch/s390/kernel/dumpstack.c:135
[<00000000c9dcd1f8>] __dump_stack lib/dump_stack.c:77 [inline]
[<00000000c9dcd1f8>] dump_stack+0x268/0x2f0 lib/dump_stack.c:118
[<00000000c5fed016>] print_address_description.constprop.0+0x5e/0x218 mm/kasan/report.c:383
[<00000000c5fec82a>] __kasan_report mm/kasan/report.c:517 [inline]
[<00000000c5fec82a>] kasan_report+0x11a/0x168 mm/kasan/report.c:534
[<00000000c98b5b60>] iucv_send_ctrl+0x390/0x3f0 net/iucv/af_iucv.c:385
[<00000000c98b6262>] iucv_sock_shutdown+0x44a/0x4c0 net/iucv/af_iucv.c:1457
[<00000000c89d3a54>] __sys_shutdown+0x12c/0x1c8 net/socket.c:2204
[<00000000c89d3b70>] __do_sys_shutdown net/socket.c:2212 [inline]
[<00000000c89d3b70>] __s390x_sys_shutdown+0x38/0x48 net/socket.c:2210
[<00000000c9e36eac>] system_call+0xe0/0x28c arch/s390/kernel/entry.S:415
There is nothing to shutdown if a connection has never been established.
Besides that iucv->hs_dev is not yet initialized if a socket is in
IUCV_OPEN state and iucv->path is not yet initialized if socket is in
IUCV_BOUND state.
So, just skip the shutdown calls for a socket in these states.
Fixes: eac3731bd04c ("[S390]: Add AF_IUCV socket support")
Fixes: 82492a355fac ("af_iucv: add shutdown for HS transport")
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
[jwi: correct one Fixes tag]
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the net core, the struct net_device_ops -> ndo_set_rx_mode()
callback is called with the dev->addr_list_lock spinlock held.
However, this driver's ndo_set_rx_mode callback eventually calls
lan743x_dp_write(), which acquires a mutex. Mutex acquisition
may sleep, and this is not allowed when holding a spinlock.
Fix by removing the dp_lock mutex entirely. Its purpose is to
prevent concurrent accesses to the data port. No concurrent
accesses are possible, because the dev->addr_list_lock
spinlock in the core only lets through one thread at a time.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201109203828.5115-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When mv88e6xxx_fid_map return error, we lost free the table.
Fix it.
Fixes: bfb255428966 ("net: dsa: mv88e6xxx: Add devlink regions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhangxiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201109144416.1540867-1-zhangxiaoxu5@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When net.ipv4.tcp_syncookies=1 and syn flood is happened,
cookie_v4_check or cookie_v6_check tries to redo what
tcp_v4_send_synack or tcp_v6_send_synack did,
rsk_window_clamp will be changed if SOCK_RCVBUF is set,
which will make rcv_wscale is different, the client
still operates with initial window scale and can overshot
granted window, the client use the initial scale but local
server use new scale to advertise window value, and session
work abnormally.
Fixes: e88c64f0a425 ("tcp: allow effective reduction of TCP's rcv-buffer via setsockopt")
Signed-off-by: Mao Wenan <wenan.mao@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/1604967391-123737-1-git-send-email-wenan.mao@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RTL8401-internal PHY identifies as RTL8201CP, and the init
sequence in r8169, copied from vendor driver r8168, uses paged
operations. Therefore set the same paged operation callbacks as
for the other Realtek PHY's.
Fixes: cdafdc29ef75 ("r8169: sync support for RTL8401 with vendor driver")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/69882f7a-ca2f-e0c7-ae83-c9b6937282cd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 6f197fb63850 ("lan743x: Added fixed link and RGMII support")
assumes that chips with an internal PHY will never have a devicetree
entry. This is incorrect: even for these chips, a devicetree entry
can be useful e.g. to pass the mac address from bootloader to chip:
&pcie {
status = "okay";
host@0 {
reg = <0 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
lan7430: ethernet@0 {
/* LAN7430 with internal PHY */
compatible = "microchip,lan743x";
status = "okay";
reg = <0 0 0 0 0>;
/* filled in by bootloader */
local-mac-address = [00 00 00 00 00 00];
};
};
};
If a devicetree entry is present, the driver will not attach the chip
to its internal phy, and the chip will be non-operational.
Fix by tweaking the phy connection algorithm:
- first try to connect to a phy specified in the devicetree
(could be 'real' phy, or just a 'fixed-link')
- if that doesn't succeed, try to connect to an internal phy, even
if the chip has a devnode
Tested on a LAN7430 with internal PHY. I cannot test a device using
fixed-link, as I do not have access to one.
Fixes: 6f197fb63850 ("lan743x: Added fixed link and RGMII support")
Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201108171224.23829-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current NetLabel code doesn't correctly keep track of the netlink
dump state in some cases, in particular when multiple interfaces with
large configurations are loaded. The problem manifests itself by not
reporting the full configuration to userspace, even though it is
loaded and active in the kernel. This patch fixes this by ensuring
that the dump state is properly reset when necessary inside the
netlbl_unlabel_staticlist() function.
Fixes: 8cc44579d1bd ("NetLabel: Introduce static network labels for unlabeled connections")
Signed-off-by: Paul Moore <paul@paul-moore.com>
Link: https://lore.kernel.org/r/160484450633.3752.16512718263560813473.stgit@sifl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update Intel Ethernet Drivers repositories to new locations.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
'igc_update_stats()' was not updating 'netdev->stats', so the returned
statistics, for example, requested by:
$ ip -s link show dev enp3s0
were not being updated and were always zero.
Fix by returning a set of statistics that are actually being
updated (adapter->stats64).
Fixes: c9a11c23ceb6 ("igc: Add netdev")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The "failure" variable is used without being initialized. It should be
set to false.
Fixes: 8cbf74149903 ("i40e, xsk: move buffer allocation out of the Rx processing loop")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix MAC setting flow for the PF driver.
Update the unicast VF's MAC address in VF structure if it is
a new setting in i40e_vc_add_mac_addr_msg.
When unicast MAC address gets deleted, record that and
set the new unicast MAC address that is already waiting in the filter
list. This logic is based on the order of messages arriving to
the PF driver.
Without this change the MAC address setting was interpreted
incorrectly in the following use cases:
1) Print incorrect VF MAC or zero MAC
ip link show dev $pf
2) Don't preserve MAC between driver reload
rmmod iavf; modprobe iavf
3) Update VF MAC when macvlan was set
ip link add link $vf address $mac $vf.1 type macvlan
4) Failed to update mac address when VF was trusted
ip link set dev $vf address $mac
This includes all other configurations including above commands.
Fixes: f657a6e1313b ("i40e: Fix VF driver MAC address configuration")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Iproute2 tc classifier terse dump has been accepted with modified syntax.
Update the tests accordingly.
Signed-off-by: Vlad Buslov <vlad@buslov.dev>
Fixes: e7534fd42a99 ("selftests: implement flower classifier terse dump tests")
Link: https://lore.kernel.org/r/20201107111928.453534-1-vlad@buslov.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull core dump fix from Al Viro:
"Fix for multithreaded coredump playing fast and loose with getting
registers of secondary threads; if a secondary gets caught in the
middle of exit(2), the conditition it will be stopped in for dumper to
examine might be unusual enough for things to go wrong.
Quite a few architectures are fine with that, but some are not."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
don't dump the threads that had been already exiting when zapped.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A handful of minor fixes and updates:
- handle missing device replace item on mount (syzbot report)
- fix space reservation calculation when finishing relocation
- fix memory leak on error path in ref-verify (debugging feature)
- fix potential overflow during defrag on 32bit arches
- minor code update to silence smatch warning
- minor error message updates"
* tag 'for-5.10-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: ref-verify: fix memory leak in btrfs_ref_tree_mod
btrfs: dev-replace: fail mount if we don't have replace item with target device
btrfs: scrub: update message regarding read-only status
btrfs: clean up NULL checks in qgroup_unreserve_range()
btrfs: fix min reserved size calculation in merge_reloc_root
btrfs: print the block rsv type when we fail our reservation
btrfs: fix potential overflow in cluster_pages_for_defrag on 32bit arch
|
|
Pull fscrypt fix from Eric Biggers:
"Fix a regression where a new WARN_ON() was reachable when using
FSCRYPT_POLICY_FLAG_IV_INO_LBLK_32 on ext4, causing xfstest
generic/602 to sometimes fail on ext4"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
fscrypt: remove reachable WARN in fscrypt_setup_iv_ino_lblk_32_key()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
"Update update to version 20.09.30, one kernel side fix"
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: update version number
powercap: restrict energy meter to root access
tools/power turbostat: harden against cpu hotplug
tools/power turbostat: adjust for temperature offset
tools/power turbostat: Build with _FILE_OFFSET_BITS=64
tools/power turbostat: Support AMD Family 19h
tools/power turbostat: Remove empty columns for Jacobsville
tools/power turbostat: Add a new GFXAMHz column that exposes gt_act_freq_mhz.
tools/power x86_energy_perf_policy: Input/output error in a VM
tools/power turbostat: Skip pc8, pc9, pc10 columns, if they are disabled
tools/power turbostat: Support additional CPU model numbers
tools/power turbostat: Fix output formatting for ACPI CST enumeration
tools/power turbostat: Replace HTTP links with HTTPS ones: TURBOSTAT UTILITY
tools/power turbostat: Use sched_getcpu() instead of hardcoded cpu 0
tools/power turbostat: Enable accumulate RAPL display
tools/power turbostat: Introduce functions to accumulate RAPL consumption
tools/power turbostat: Make the energy variable to be 64 bit
tools/power turbostat: Always print idle in the system configuration header
tools/power turbostat: Print /dev/cpu_dma_latency
|
|
Add Alder Lake ACPI IDs for DPTF devices.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make intel_pstate take the new CPUFREQ_GOV_STRICT_TARGET governor
flag into account when it operates in the passive mode with HWP
enabled, so as to fix the "powersave" governor behavior in that
case (currently, HWP is allowed to scale the performance all the
way up to the policy max limit when the "powersave" governor is
used, but it should be constrained to the policy min limit then).
Fixes: f6ebbcf08f37 ("cpufreq: intel_pstate: Implement passive mode with HWP enabled")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 5.9+ <stable@vger.kernel.org> # 5.9+: 9a2a9ebc0a75 cpufreq: Introduce governor flags
Cc: 5.9+ <stable@vger.kernel.org> # 5.9+: 218f66870181 cpufreq: Introduce CPUFREQ_GOV_STRICT_TARGET
Cc: 5.9+ <stable@vger.kernel.org> # 5.9+: ea9364bbadf1 cpufreq: Add strict_target to struct cpufreq_policy
|
|
Add a new field to be set when the CPUFREQ_GOV_STRICT_TARGET flag is
set for the current governor to struct cpufreq_policy, so that the
drivers needing to check CPUFREQ_GOV_STRICT_TARGET do not have to
access the governor object during every frequency transition.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Introduce a new governor flag, CPUFREQ_GOV_STRICT_TARGET, for the
governors that want the target frequency to be set exactly to the
given value without leaving any room for adjustments on the hardware
side and set this flag for the powersave and performance governors.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
A new cpufreq governor flag will be added subsequently, so replace
the bool dynamic_switching fleid in struct cpufreq_governor with a
flags field and introduce CPUFREQ_GOV_DYNAMIC_SWITCHING to set for
the "dynamic switching" governors instead of it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
goodbye summer...
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Remove non-privileged user access to power data contained in
/sys/class/powercap/intel-rapl*/*/energy_uj
Non-privileged users currently have read access to power data and can
use this data to form a security attack. Some privileged
drivers/applications need read access to this data, but don't expose it
to non-privileged users.
For example, thermald uses this data to ensure that power management
works correctly. Thus removing non-privileged access is preferred over
completely disabling this power reporting capability with
CONFIG_INTEL_RAPL=n.
Fixes: 95677a9a3847 ("PowerCap: Fix mode for energy counter")
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: stable@vger.kernel.org
|
|
The mptcp proto struct currently does not provide the
required limit for forward memory scheduling. Under
pressure sk_rmem_schedule() will unconditionally try
to use such field and will oops.
Address the issue inheriting the tcp limit, as we already
do for the wmem one.
Fixes: 9c3f94e1681b ("mptcp: add missing memory scheduling in the rx path")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Link: https://lore.kernel.org/r/37af798bd46f402fb7c79f57ebbdd00614f5d7fa.1604861097.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
2.5 times faster would be 3.5 Gbps (4.375 Gbaud after 8b/10b encoding).
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20201107220822.1291215-1-j.neuschaefer@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After updating userspace Ethtool from 5.7 to 5.9, I noticed that
NETDEV_FEAT_CHANGE is no more raised when changing netdev features
through Ethtool.
That's because the old Ethtool ioctl interface always calls
netdev_features_change() at the end of user request processing to
inform the kernel that our netdevice has some features changed, but
the new Netlink interface does not. Instead, it just notifies itself
with ETHTOOL_MSG_FEATURES_NTF.
Replace this ethtool_notify() call with netdev_features_change(), so
the kernel will be aware of any features changes, just like in case
with the ioctl interface. This does not omit Ethtool notifications,
as Ethtool itself listens to NETDEV_FEAT_CHANGE and drops
ETHTOOL_MSG_FEATURES_NTF on it
(net/ethtool/netlink.c:ethnl_netdev_event()).
From v1 [1]:
- dropped extra new line as advised by Jakub;
- no functional changes.
[1] https://lore.kernel.org/netdev/AlZXQ2o5uuTVHCfNGOiGgJ8vJ3KgO5YIWAnQjH0cDE@cp3-web-009.plabs.ch
Fixes: 0980bfcd6954 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/r/ahA2YWXYICz5rbUSQqNG4roJ8OlJzzYQX7PTiG80@cp4-web-028.plabs.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jianlin reports that a bridged IPv6 VXLAN endpoint, carrying IPv6
packets over a link with a PMTU estimation of exactly 1350 bytes,
won't trigger ICMPv6 Packet Too Big replies when the encapsulated
datagrams exceed said PMTU value. VXLAN over IPv6 adds 70 bytes of
overhead, so an ICMPv6 reply indicating 1280 bytes as inner MTU
would be legitimate and expected.
This comes from an off-by-one error I introduced in checks added
as part of commit 4cb47a8644cc ("tunnels: PMTU discovery support
for directly bridged IP packets"), whose purpose was to prevent
sending ICMPv6 Packet Too Big messages with an MTU lower than the
smallest permissible IPv6 link MTU, i.e. 1280 bytes.
In iptunnel_pmtud_check_icmpv6(), avoid triggering a reply only if
the advertised MTU would be less than, and not equal to, 1280 bytes.
Also fix the analogous comparison for IPv4, that is, skip the ICMP
reply only if the resulting MTU is strictly less than 576 bytes.
This becomes apparent while running the net/pmtu.sh bridged VXLAN
or GENEVE selftests with adjusted lower-link MTU values. Using
e.g. GENEVE, setting ll_mtu to the values reported below, in the
test_pmtu_ipvX_over_bridged_vxlanY_or_geneveY_exception() test
function, we can see failures on the following tests:
test | ll_mtu
-------------------------------|--------
pmtu_ipv4_br_geneve4_exception | 626
pmtu_ipv6_br_geneve4_exception | 1330
pmtu_ipv6_br_geneve6_exception | 1350
owing to the different tunneling overheads implied by the
corresponding configurations.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 4cb47a8644cc ("tunnels: PMTU discovery support for directly bridged IP packets")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Link: https://lore.kernel.org/r/4f5fc2f33bfdf8409549fafd4f952b008bf04d63.1604681709.git.sbrivio@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to the legacy usage of hard_header_len for SIT tunnels while
already using infrastructure from net/ipv4/ip_tunnel.c the
calculation of the path MTU in tnl_update_pmtu is incorrect.
This leads to unnecessary creation of MTU exceptions for any
flow going over a SIT tunnel.
As SIT tunnels do not have a header themsevles other than their
transport (L3, L2) headers we're leaving hard_header_len set to zero
as tnl_update_pmtu is already taking care of the transport headers
sizes.
This will also help avoiding unnecessary IPv6 GC runs and spinlock
contention seen when using SIT tunnels and for more than
net.ipv6.route.gc_thresh flows.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.")
Signed-off-by: Oliver Herms <oliver.peter.herms@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20201103104133.GA1573211@tws
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- fix compilation error when PMD and PUD are folded
- fix regression in reads-as-zero behaviour of ID_AA64ZFR0_EL1
- add aarch64 get-reg-list test
x86:
- fix semantic conflict between two series merged for 5.10
- fix (and test) enforcement of paravirtual cpuid features
selftests:
- various cleanups to memory management selftests
- new selftests testcase for performance of dirty logging"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
KVM: selftests: allow two iterations of dirty_log_perf_test
KVM: selftests: Introduce the dirty log perf test
KVM: selftests: Make the number of vcpus global
KVM: selftests: Make the per vcpu memory size global
KVM: selftests: Drop pointless vm_create wrapper
KVM: selftests: Add wrfract to common guest code
KVM: selftests: Simplify demand_paging_test with timespec_diff_now
KVM: selftests: Remove address rounding in guest code
KVM: selftests: Factor code out of demand_paging_test
KVM: selftests: Use a single binary for dirty/clear log test
KVM: selftests: Always clear dirty bitmap after iteration
KVM: selftests: Add blessed SVE registers to get-reg-list
KVM: selftests: Add aarch64 get-reg-list test
selftests: kvm: test enforcement of paravirtual cpuid features
selftests: kvm: Add exception handling to selftests
selftests: kvm: Clear uc so UCALL_NONE is being properly reported
selftests: kvm: Fix the segment descriptor layout to match the actual layout
KVM: x86: handle MSR_IA32_DEBUGCTLMSR with report_ignored_msrs
kvm: x86: request masterclock update any time guest uses different msr
kvm: x86: ensure pv_cpuid.features is initialized when enabling cap
...
|
|
Pull nfsd fixes from Bruce Fields:
"This is mainly server-to-server copy and fallout from Chuck's 5.10 rpc
refactoring"
* tag 'nfsd-5.10-1' of git://linux-nfs.org/~bfields/linux:
net/sunrpc: fix useless comparison in proc_do_xprt()
net/sunrpc: return 0 on attempt to write to "transports"
NFSD: fix missing refcount in nfsd4_copy by nfsd4_do_async_copy
NFSD: Fix use-after-free warning when doing inter-server copy
NFSD: MKNOD should return NFSERR_BADTYPE instead of NFSERR_INVAL
SUNRPC: Fix general protection fault in trace_rpc_xdr_overflow()
NFSD: NFSv3 PATHCONF Reply is improperly formed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes and cleanups from Ted Ts'o:
"More fixes and cleanups for the new fast_commit features, but also a
few other miscellaneous bug fixes and a cleanup for the MAINTAINERS
file"
* tag 'ext4_for_linus_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (28 commits)
jbd2: fix up sparse warnings in checkpoint code
ext4: fix sparse warnings in fast_commit code
ext4: cleanup fast commit mount options
jbd2: don't start fast commit on aborted journal
ext4: make s_mount_flags modifications atomic
ext4: issue fsdev cache flush before starting fast commit
ext4: disable fast commit with data journalling
ext4: fix inode dirty check in case of fast commits
ext4: remove unnecessary fast commit calls from ext4_file_mmap
ext4: mark buf dirty before submitting fast commit buffer
ext4: fix code documentatioon
ext4: dedpulicate the code to wait on inode that's being committed
jbd2: don't read journal->j_commit_sequence without taking a lock
jbd2: don't touch buffer state until it is filled
jbd2: add todo for a fast commit performance optimization
jbd2: don't pass tid to jbd2_fc_end_commit_fallback()
jbd2: don't use state lock during commit path
jbd2: drop jbd2_fc_init documentation
ext4: clean up the JBD2 API that initializes fast commits
jbd2: rename j_maxlen to j_total_len and add jbd2_journal_max_txn_bufs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
"A week ago, Vladimir reported an issue that the kernel log would
become polluted if the page allocation debug option is enabled. I also
found this when I cleaned up magical page->mapping and originally
planned to submit these all for 5.11 but it seems the impact can be
noticed so submit the fix in advance.
In addition, nl6720 also reported that atime is empty although EROFS
has the only one on-disk timestamp as a practical consideration for
now but it's better to derive it as what we did for the other
timestamps.
Summary:
- fix setting up pcluster improperly for temporary pages
- derive atime instead of leaving it empty"
* tag 'erofs-for-5.10-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix setting up pcluster for temporary pages
erofs: derive atime instead of leaving it empty
|
|
The Medion Akoya E2228T's ACPI _LID implementation is quite broken,
it has the same issues as the one from the Medion Akoya E2215T:
1. For notifications it uses an ActiveLow Edge GpioInt, rather then
an ActiveBoth one, meaning that the device is only notified when the
lid is closed, not when it is opened.
2. Matching with this its _LID method simply always returns 0 (closed)
In order for the Linux LID code to work properly with this implementation,
the lid_init_state selection needs to be set to ACPI_BUTTON_LID_INIT_OPEN,
add a DMI quirk for this.
While working on this I also found out that the MD60### part of the model
number differs per country/batch while all of the E2215T and E2228T models
have this issue, so also remove the " MD60198" part from the E2215T quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Clang is more aggressive about -Wformat warnings when the format flag
specifies a type smaller than the parameter. It turns out that gsi is an
int. Fixes:
drivers/acpi/evged.c:105:48: warning: format specifies type 'unsigned
char' but the argument has type 'unsigned int' [-Wformat]
trigger == ACPI_EDGE_SENSITIVE ? 'E' : 'L', gsi);
^~~
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Fixes: ea6f3af4c5e6 ("ACPI: GED: add support for _Exx / _Lxx handler methods")
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Replaces spaces with tabs where spaces have been (inconsistently) used
for indentation and removes trailing whitespaces.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For some reason building with W=1 doesn't pick up on this, but the
kerneldoc name for acpi_dma_configure_id() is not right, so fix it up.
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
