| Age | Commit message (Collapse) | Author |
|---|
|
Do not check the encoding when deriving 1000BASE-X from the bitrate
when no other modes are discovered. Some GPON modules (VSOL V2801F
and CarlitoxxPro CPGOS03-0490 v2.0) indicate NRZ encoding with a
1200Mbaud bitrate, but should be driven with 1000BASE-X on the host
side.
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a workaround for the detection of VSOL V2801F / CarlitoxxPro
CPGOS03-0490 v2.0 GPON module which CarlitoxxPro states needs single
byte I2C reads to the EEPROM.
Pali Rohár reports that he also has a CarlitoxxPro-based V2801F module,
which reports a manufacturer of "OEM". This manufacturer can't be
matched as it appears in many different modules, so also match the part
number too.
Reported-by: Thomas Schreiber <tschreibe@gmail.com>
Reported-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. When the x25 module gets loaded, layer 2 may already be running and
connected. In this case, although we are in X25_LINK_STATE_0, we still
need to handle the Restart Request received, rather than ignore it.
2. When we are in X25_LINK_STATE_2, we have already sent a Restart Request
and is waiting for the Restart Confirmation with t20timer. t20timer will
restart itself repeatedly forever so it will always be there, as long as we
are in State 2. So we don't need to check x25_t20timer_pending again.
Fixes: d023b2b9ccc2 ("net/x25: fix restart request/confirm handling")
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo Abeni says:
====================
mptcp: a bunch of fixes
This series includes a few fixes following-up the
recent code refactor for the MPTCP RX and TX paths.
Boundling them together, since the fixes are somewhat
related.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the workqueue disposes of the msk, the subflows can still
receive some data from the peer after __mptcp_close_ssk()
completes.
The above could trigger a race between the msk receive path and the
msk destruction. Acquiring the mptcp_data_lock() in __mptcp_destroy_sock()
will not save the day: the rx path could be reached even after msk
destruction completes.
Instead use the subflow 'disposable' flag to prevent entering
the msk receive path after __mptcp_close_ssk().
Fixes: e16163b6e2b7 ("mptcp: refactor shutdown and close")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a MPTCP listener socket is closed with unaccepted
children pending, the ULP release callback will be invoked,
but nobody will call into __mptcp_close_ssk() on the
corresponding subflow.
As a consequence, at ULP release time, the 'disposable' flag
will be cleared and the subflow context memory will be leaked.
This change addresses the issue always freeing the context if
the subflow is still in the accept queue at ULP release time.
Additionally, this fixes an incorrect code reference in the
related comment.
Note: this fix leverages the changes introduced by the previous
commit.
Fixes: e16163b6e2b7 ("mptcp: refactor shutdown and close")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Christoph reported the following splat:
WARNING: CPU: 0 PID: 4615 at net/ipv4/inet_connection_sock.c:1031 inet_csk_listen_stop+0x8e8/0xad0 net/ipv4/inet_connection_sock.c:1031
Modules linked in:
CPU: 0 PID: 4615 Comm: syz-executor.4 Not tainted 5.9.0 #37
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:inet_csk_listen_stop+0x8e8/0xad0 net/ipv4/inet_connection_sock.c:1031
Code: 03 00 00 00 e8 79 b2 3d ff e9 ad f9 ff ff e8 1f 76 ba fe be 02 00 00 00 4c 89 f7 e8 62 b2 3d ff e9 14 f9 ff ff e8 08 76 ba fe <0f> 0b e9 97 f8 ff ff e8 fc 75 ba fe be 03 00 00 00 4c 89 f7 e8 3f
RSP: 0018:ffffc900037f7948 EFLAGS: 00010293
RAX: ffff88810a349c80 RBX: ffff888114ee1b00 RCX: ffffffff827b14cd
RDX: 0000000000000000 RSI: ffffffff827b1c38 RDI: 0000000000000005
RBP: ffff88810a2a8000 R08: ffff88810a349c80 R09: fffff520006fef1f
R10: 0000000000000003 R11: fffff520006fef1e R12: ffff888114ee2d00
R13: dffffc0000000000 R14: 0000000000000001 R15: ffff888114ee1d68
FS: 00007f2ac1945700(0000) GS:ffff88811b400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffd44798bc0 CR3: 0000000109810002 CR4: 0000000000170ef0
Call Trace:
__tcp_close+0xd86/0x1110 net/ipv4/tcp.c:2433
__mptcp_close_ssk+0x256/0x430 net/mptcp/protocol.c:1761
__mptcp_destroy_sock+0x49b/0x770 net/mptcp/protocol.c:2127
mptcp_close+0x62d/0x910 net/mptcp/protocol.c:2184
inet_release+0xe9/0x1f0 net/ipv4/af_inet.c:434
__sock_release+0xd2/0x280 net/socket.c:596
sock_close+0x15/0x20 net/socket.c:1277
__fput+0x276/0x960 fs/file_table.c:281
task_work_run+0x109/0x1d0 kernel/task_work.c:151
get_signal+0xe8f/0x1d40 kernel/signal.c:2561
arch_do_signal+0x88/0x1b60 arch/x86/kernel/signal.c:811
exit_to_user_mode_loop kernel/entry/common.c:161 [inline]
exit_to_user_mode_prepare+0x9b/0xf0 kernel/entry/common.c:191
syscall_exit_to_user_mode+0x22/0x150 kernel/entry/common.c:266
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f2ac1254469
Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d ff 49 2b 00 f7 d8 64 89 01 48
RSP: 002b:00007f2ac1944dc8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffbf RBX: 000000000069bf00 RCX: 00007f2ac1254469
RDX: 0000000000000000 RSI: 0000000000008982 RDI: 0000000000000003
RBP: 000000000069bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000069bf0c
R13: 00007ffeb53f178f R14: 00000000004668b0 R15: 0000000000000003
After commit 0397c6d85f9c ("mptcp: keep unaccepted MPC subflow into
join list"), the msk's workqueue and/or PM can touch the MPC
subflow - and acquire its socket lock - even if it's still unaccepted.
If the above event races with the relevant listener socket close, we
can end-up with the above splat.
This change addresses the issue delaying the MPC socket insertion
in conn_list at accept time - that is, partially reverting the
blamed commit.
We must additionally ensure that mptcp_pm_fully_established()
happens after accept() time, or the PM will not be able to
handle properly such event - conn_list could be empty otherwise.
In the receive path, we check the subflow list node to ensure
it is out of the listener queue. Be sure client subflows do
not match transiently such condition moving them into the join
list earlier at creation time.
Since we now have multiple mptcp_pm_fully_established() call sites
from different code-paths, said helper can now race with itself.
Use an additional PM status bit to avoid multiple notifications.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/103
Fixes: 0397c6d85f9c ("mptcp: keep unaccepted MPC subflow into join list"),
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. In x25_xmit, skb_reset_network_header is not necessary before we call
lapb_data_request. The lapb module doesn't need skb->network_header.
So there is no need to set skb->network_header before calling
lapb_data_request.
2. In x25_data_indication (called by the lapb module after data have
been received), skb_reset_network_header is not necessary before we
call netif_rx. After we call netif_rx, the code in net/core/dev.c will
call skb_reset_network_header before handing the skb to upper layers
(in __netif_receive_skb_core, called by __netif_receive_skb_one_core,
called by __netif_receive_skb, called by process_backlog). So we don't
need to call skb_reset_network_header by ourselves.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
partial success
We observed that in the error case for batched send_subcrq_indirect() the
driver does not account for the partial success case. This caused Linux to
crash when free_map and pool index are inconsistent.
Driver needs to update the rx pools "available" count when some batched
sends worked but an error was encountered as part of the whole operation.
Also track replenish_add_buff_failure for statistic purposes.
Fixes: 4f0b6812e9b9a ("ibmvnic: Introduce batched RX buffer descriptor transmission")
Signed-off-by: Dwip N. Banerjee <dnbanerg@us.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mat Martineau says:
====================
mptcp: Add port parameter to ADD_ADDR option
The ADD_ADDR MPTCP option is used to announce available IP addresses
that a peer may connect to when adding more TCP subflows to an existing
MPTCP connection. There is an optional port number field in that
ADD_ADDR header, and this patch set adds capability for that port number
to be sent and received.
Patches 1, 2, and 4 refactor existing ADD_ADDR code to simplify implementation
of port number support.
Patches 3 and 5 are the main functional changes, for sending and
receiving the port number in the MPTCP ADD_ADDR option.
Patch 6 sends the ADD_ADDR option with port number on a bare TCP ACK,
since the extra length of the option may run in to cases where
sufficient TCP option space is not available on a data packet.
Patch 7 plumbs in port number support for the in-kernel MPTCP path
manager.
Patches 8-11 add some optional debug output and a little more cleanup
refactoring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the local variable sk has been defined, use it instead of
open-coding.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the RM_ADDR signal had been reused with add_addr_signal, it's not
suitable to call it add_addr_signal or mptcp_add_addr_status. So this
patch renamed add_addr_signal to addr_signal, and renamed
mptcp_add_addr_status to mptcp_addr_signal_status.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reused add_addr_signal for the RM_ADDR announcing signal, by
defining a new ADD_ADDR status named MPTCP_RM_ADDR_SIGNAL. Then the flag
rm_addr_signal in PM could be dropped.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch printed out more debugging information for the ADD_ADDR
suboption parsing on the incoming path.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added a new parameter 'port' for mptcp_pm_announce_addr. If
this parameter is true, we set the MPTCP_ADD_ADDR_PORT bit of the
add_addr_signal. That means the announced address is added with a port
number.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The process is similar to that of the ADD_ADDR IPv6, this patch also sent
out a pure ack for the ADD_ADDR using port.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added a new add_addr_signal type named MPTCP_ADD_ADDR_PORT,
to identify it is an address with port to be added.
It also added a new parameter 'port' for both mptcp_add_addr_len and
mptcp_pm_add_addr_signal.
In mptcp_established_options_add_addr, we check whether the announced
address is added with port. If it is, we put this port number to
mptcp_out_options's port field.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch uses adding up size to get the ADD_ADDR suboption length rather
than returning the ADD_ADDR size constants.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rfc8684, the length of ADD_ADDR suboption with IPv4 address and port
is 18 octets, but mptcp_write_options is 32-bit aligned, so we need to
pad it to 20 octets. All the other port related option lengths need to
be added up 2 octets similarly.
This patch added a new field 'port' in mptcp_out_options. When this
field is set with a port number, we need to add up 4 octets for the
ADD_ADDR suboption, and put the port number into the suboption.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The length of ADD_ADDR6 is 12 octets longer than ADD_ADDR. That's the
only difference between them.
This patch dropped the duplicate code between ADD_ADDR and ADD_ADDR6
suboptions writing, and unify them into one.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two differences between ADD_ADDR suboption and ADD_ADDR echo
suboption: The length of the former is 8 octets longer than the length
of the latter. The former's echo-flag is 0, and latter's echo-flag is 1.
This patch added two local variables, len and echo, to unify ADD_ADDR
and ADD_ADDR echo suboptions writing.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2020-12-09
This series contains updates to ice driver only.
Bruce changes the allocation of ice_flow_prof_params from stack to heap to
avoid excessive stack usage. Corrects a misleading comment and silences a
sparse warning that is not a problem.
Paul allows for HW initialization to continue if PHY abilities cannot
be obtained.
Jeb removes bypassing FW link override and reading Option ROM and
netlist information for non-E810 devices as this is now available on
other devices.
Nick removes vlan_ena field as this information can be gathered by
checking num_vlan.
Jake combines format strings and debug prints to the same line.
Simon adds a space to fix string concatenation.
v4: Drop ACL patches. Change PHY abilities failure message from debug to
warning.
v3: Fix email address for DaveM and fix character in cover letter
v2: Expand on commit message for patch 3 to show example usage/commands.
Reduce number of defensive checks being done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bongsu Jeon says:
====================
nfc: s3fwrn5: Change I2C interrupt trigger to EDGE_RISING
For stable Samsung's I2C interrupt handling, I changed the interrupt
trigger from IRQ_TYPE_LEVEL_HIGH to IRQ_TYPE_EDGE_RISING and removed
the hard coded interrupt trigger type in the i2c module for the flexible
control.
1/2 is the changed dt binding for the edge rising trigger.
2/2 is to remove the hard coded interrupt trigger type in the i2c module.
ChangeLog:
v2:
2/2
- remove the hard coded interrupt trigger type.
Bongsu Jeon (2):
dt-bindings: net: nfc: s3fwrn5: Change I2C interrupt trigger to
EDGE_RISING
nfc: s3fwrn5: Remove hard coded interrupt trigger type from the i2c
module
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the flexible control of interrupt trigger type, remove the hard coded
interrupt trigger type in the i2c module. The trigger type will be loaded
from a dts.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change interrupt trigger from IRQ_TYPE_LEVEL_HIGH to IRQ_TYPE_EDGE_RISING
for stable NFC I2C interrupt handling.
Samsung's NFC Firmware sends an i2c frame as below.
1. NFC Firmware sets the GPIO(interrupt pin) high when there is an i2c
frame to send.
2. If the CPU's I2C master has received the i2c frame, NFC F/W sets the
GPIO low.
NFC driver's i2c interrupt handler would be called in the abnormal case
as the NFC FW task of number 2 is delayed because of other high priority
tasks.
In that case, NFC driver will try to receive the i2c frame but there isn't
any i2c frame to send in NFC.
It would cause an I2C communication problem. This case would hardly happen.
But, I changed the interrupt as a defense code.
If Driver uses the TRIGGER_RISING instead of the LEVEL trigger,
there would be no problem even if the NFC FW task is delayed.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Claudiu Beznea says:
====================
net: macb: add support for sama7g5
This series adds support for SAMA7G5 Ethernet interfaces: one 10/100Mbps
and one 1Gbps interfaces.
Along with it I also included a fix to disable clocks for SiFive FU540-C000
on failure path of fu540_c000_clk_init().
Thank you,
Claudiu Beznea
Changed in v3:
- use clk_bulk_disable_unprepare in patch 3/8
- corrected clang compilation warning in patch 3/8
- revert changes in macb_clk_init() in patch 3/8
Changes in v2:
- introduced patch "net: macb: add function to disable all macb clocks" and
update patch "net: macb: unprepare clocks in case of failure" accordingly
- collected tags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for SAMA7G5 10/100Mbps interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for SAMA7G5 gigabit ethernet interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add documentation for SAMA7G5 gigabit ethernet interface.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
