| Age | Commit message (Collapse) | Author |
|---|
|
The register and FIFO accessors are bus specific, so is locking.
Implement callbacks so that each variant of the KS8851 can implement
matching accessors and locking, and use the rest of the common code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The parallel bus variant does not need to use the TX interrupt at all
as it writes the TX FIFO directly with in .ndo_start_xmit, permit the
drivers to configure the interrupt enable bits.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While the SPI version of the KS8851 requires a TX worker thread to pump
data via SPI, the parallel bus version can write data into the TX FIFO
directly in .ndo_start_xmit, as the parallel bus access is much faster
and does not sleep. Factor out this TX work flush part, so it can be
overridden by the parallel bus driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factor out common code into ks8851_probe_common() and
ks8851_remove_common() to permit both SPI and parallel
bus driver variants to use the common code path for
both probing and removal.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new struct ks8851_net_spi, which embeds the original
struct ks8851_net and contains the entries specific only to
the SPI variant of KS8851.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factor out this netif_rx_ni(), so it could be overridden by the parallel
bus variant of the KS8851 driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull out bus access locking code into separate functions, this is done
in preparation for unifying the driver with the parallel bus one. The
parallel bus driver does not need heavy mutex locking of the bus and
works better with spinlocks, hence prepare these locking functions to
be overridden then.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RXFC register is the only one being read using 8-bit accessors.
To make it easier to support the 16-bit accesses used by the parallel
bus variant of KS8851, use 16-bit accessor to read RXFC register as
well as neighboring RXFCTR register.
Remove ks8851_rdreg8() as it is not used anywhere anymore.
There should be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the SPI variant of KS8851, the MAC address can be programmed with
either 8/16/32-bit writes. To make it easier to support the 16-bit
parallel option of KS8851 too, switch both the MAC address programming
and readout to 16-bit operations.
Remove ks8851_wrreg8() as it is not used anywhere anymore.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851_rdreg32() is used only in one place, to read two registers
using a single read. To make it easier to support 16-bit accesses via
parallel bus later on, replace this single read with two 16-bit reads
from each of the registers and drop the ks8851_rdreg32() altogether.
If this has noticeable performance impact on the SPI variant of KS8851,
then we should consider using regmap to abstract the SPI and parallel
bus options and in case of SPI, permit regmap to merge register reads
of neighboring registers into single, longer, read.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace spi_{get,set}_drvdata() with dev_{get,set}_drvdata(), which
works for both SPI and platform drivers. This is done in preparation
for unifying the KS8851 SPI and parallel bus drivers.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use device managed version of alloc_etherdev() to simplify the code.
No functional change intended.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the driver probe function already has a struct device *dev pointer
and can easily derive of_node pointer from it, pass the of_node pointer as
a parameter to ks8851_init_mac() to avoid fishing it out from ks->spidev.
This is the only reference to spidev in the function, so get rid of it.
This is done in preparation for unifying the KS8851 SPI and parallel bus
drivers.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netdev_err() instead of dev_err() to avoid accessing the spidev->dev
in the interrupt handler. This is the only place which uses the spidev
in this function, so replace it with netdev_err() to get rid of it. This
is done in preparation for unifying the KS8851 SPI and parallel drivers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename ndev variable to netdev for the sake of consistency.
No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull out the spi->dev into one common place in the function instead of
having it repeated over and over again. This is done in preparation for
unifying ks8851 and ks8851-mll drivers. No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ronak Doshi says:
====================
vmxnet3: upgrade to version 4
vmxnet3 emulation has recently added several new features which includes
offload support for tunnel packets, support for new commands the driver
can issue to emulation, change in descriptor fields, etc. This patch
series extends the vmxnet3 driver to leverage these new features.
Compatibility is maintained using existing vmxnet3 versioning mechanism as
follows:
- new features added to vmxnet3 emulation are associated with new vmxnet3
version viz. vmxnet3 version 4.
- emulation advertises all the versions it supports to the driver.
- during initialization, vmxnet3 driver picks the highest version number
supported by both the emulation and the driver and configures emulation
to run at that version.
In particular, following changes are introduced:
Patch 1:
This patch introduces utility macros for vmxnet3 version 4 comparison
and updates Copyright information.
Patch 2:
This patch implements get_rss_hash_opts and set_rss_hash_opts methods
to allow querying and configuring different Rx flow hash configurations
which can be used to support UDP/ESP RSS.
Patch 3:
This patch introduces segmentation and checksum offload support for
encapsulated packets. This avoids segmenting and calculating checksum
for each segment and hence gives performance boost.
Patch 4:
With all vmxnet3 version 4 changes incorporated in the vmxnet3 driver,
with this patch, the driver can configure emulation to run at vmxnet3
version 4.
Changes in v3 -> v4:
- Replaced BUG_ON() with WARN_ON_ONCE()
Changes in v2 -> v3:
- fixed get_rss_hash_opts to return correct values for udp rss
Changes in v2:
- Fixed compilation issue due to missing closed brace
- added fallthrough comment
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With all vmxnet3 version 4 changes incorporated in the vmxnet3 driver,
the driver can configure emulation to run at vmxnet3 version 4, provided
the emulation advertises support for version 4.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vmxnet3 version 3 device supports checksum/TSO offload. Thus, vNIC to
pNIC traffic can leverage hardware checksum/TSO offloads. However,
vmxnet3 does not support checksum/TSO offload for Geneve/VXLAN
encapsulated packets. Thus, for a vNIC configured with an overlay, the
guest stack must first segment the inner packet, compute the inner
checksum for each segment and encapsulate each segment before
transmitting the packet via the vNIC. This results in significant
performance penalty.
This patch will enhance vmxnet3 to support Geneve/VXLAN TSO as well as
checksum offload.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With vmxnet3 version 4, the emulation supports multiqueue(RSS) for
UDP and ESP traffic. A guest can enable/disable RSS for UDP/ESP over
IPv4/IPv6 by issuing commands introduced in this patch. ESP ipv6 is
not yet supported in this patch.
This patch implements get_rss_hash_opts and set_rss_hash_opts
methods to allow querying and configuring different Rx flow hash
configurations.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vmxnet3 is currently at version 3 and this patch initiates the
preparation to accommodate changes for version 4. Introduced utility
macros for vmxnet3 version 4 comparison and update Copyright
information.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'nic_data' is no longer used outside of the #ifdef block
in efx_ef10_set_mac_address:
drivers/net/ethernet/sfc/ef10.c:3231:28: error: unused variable 'nic_data' [-Werror,-Wunused-variable]
struct efx_ef10_nic_data *nic_data = efx->nic_data;
Move the variable into a local scope.
Fixes: dfcabb078847 ("sfc: move vport_id to struct efx_nic")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-27
This series contains updates to the ice driver only.
Jesse fixes a number of issues, starting with fixing the remaining
signed versus unsigned comparison issues. Cleaned up an unused code
define. Fixed the implementation of the manage MAC write command, to
simplify it by using a simple array to represent the MAC address when
writing it.
Paul fixes the setting of the VF default LAN address, by removing a
check that assumed that the address had been deleted and zeroed.
Surabhi prevents a memory leak on filter management initialization
failures and during queue initialization and buffer allocation failures.
Brett adds additional receive error counters that are reported by
ethtool. Fixed the enabling and disabling of VLAN stripping when the
PVID has been set.
Evan fixes a race condition between the firmware and software, which can
occur between the admin queue setup and the first command sent.
Marta fixes the driver when XDP transmit rings are destroyed, also make
sure the XDP transmit queues are also destroyed. Update the statistics
when XDP transmit programs are loaded and packets are sent. Changed the
number of XDP transmit queues to match the number of receive queues,
instead of matching the number of transmit queues.
Bruce avoids undefined behavior by not writing the 8-bit element
init_q_state with the associated internal-to-hardware field which is
122-bits.
Anirudh (Ani) refactors the receive checksum checks.
Krzysztof notifies the user if the fill queue is not long enough to
prepare all buffers before packet processing starts and allocates the
buffers during the NAPI poll.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Christoph Hellwig says:
====================
remove most callers of kernel_setsockopt v3
this series removes most callers of the kernel_setsockopt functions, and
instead switches their users to small functions that implement setting a
sockopt directly using a normal kernel function call with type safety and
all the other benefits of not having a function call.
In some cases these functions seem pretty heavy handed as they do
a lock_sock even for just setting a single variable, but this mirrors
the real setsockopt implementation unlike a few drivers that just set
set the fields directly.
Changes since v2:
- drop the separately merged kernel_getopt_removal
- drop the sctp patches, as there is conflicting cleanup going on
- add an additional ACK for the rxrpc changes
Changes since v1:
- use ->getname for sctp sockets in dlm
- add a new ->bind_add struct proto method for dlm/sctp
- switch the ipv6 and remaining sctp helpers to inline function so that
the ipv6 and sctp modules are not pulled in by any module that could
potentially use ipv6 or sctp connections
- remove arguments to various sock_* helpers that are always used with
the same constant arguments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid using kernel_setsockopt for the TIPC_IMPORTANCE option when we can
just use the internal helper. The only change needed is to pass a struct
sock instead of tipc_sock, which is private to socket.c
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the RXRPC_MIN_SECURITY_LEVEL sockopt from
kernel space without going through a fake uaccess.
Thanks to David Howells for the documentation updates.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the IPV6_RECVPKTINFO sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the IPV6_ADD_PREFERENCES sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the IPV6_RECVERR sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the IPV6_V6ONLY sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the IP_PKTINFO sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the IP_MTU_DISCOVER sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com> [rxrpc bits]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the IP_RECVERR sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the IP_FREEBIND sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the IP_TOS sockopt from kernel space without
going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the TCP_KEEPCNT sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the TCP_KEEPINTVL sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the TCP_KEEP_IDLE sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the TCP_USER_TIMEOUT sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the TCP_SYNCNT sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the TCP_QUICKACK sockopt from kernel space
without going through a fake uaccess. Cleanup the callers to avoid
pointless wrappers now that this is a simple function call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the TCP_NODELAY sockopt from kernel space
without going through a fake uaccess. Cleanup the callers to avoid
pointless wrappers now that this is a simple function call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the TCP_CORK sockopt from kernel space
without going through a fake uaccess. Cleanup the callers to avoid
pointless wrappers now that this is a simple function call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the SO_REUSEPORT sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the SO_RCVBUFFORCE sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the SO_KEEPALIVE sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly enable timestamps instead of setting the
SO_TIMESTAMP* sockopts from kernel space and going through a fake
uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the SO_BINDTOIFINDEX sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the SO_SNDTIMEO_NEW sockopt from kernel
space without going through a fake uaccess. The interface is
simplified to only pass the seconds value, as that is the only
thing needed at the moment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to directly set the SO_PRIORITY sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
