| Age | Commit message (Collapse) | Author |
|---|
|
This adds new w5100-spi driver which shares the bus interface
independent code with existing w5100 driver.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SPI transfer routines are callable only from contexts that can sleep.
This adds ability to tell the core driver that the interface mode
cannot access w5100 register on atomic contexts. In this case,
workqueue and threaded irq are required.
This also corrects timeout period waiting for command register to be
automatically cleared because the latency of the register access with
SPI transfer can be interfered by other contexts.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The w5100 driver currently only supports direct and indirect bus
interface mode which use MMIO space for accessing w5100 registers.
In order to support SPI interface mode which is supported by W5100 chip,
this makes the bus interface abstraction layer more generic so that
separated w5100-spi driver can use w5100 driver as core module.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of sprinkle mmiowb over the driver code, move it into primary
register write callbacks. (w5100_write, w5100_write16, w5100_writebuf)
This is a preparation for supporting SPI interface which doesn't use
MMIO for accessing w5100 registers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We only need to do the synchronize_net dance once for both, ipv4 and
ipv6 sockets, thus removing one synchronize_net in case both sockets get
dismantled.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to the fact that the udp socket is destructed asynchronously in a
work queue, we have some nondeterministic behavior during shutdown of
vxlan tunnels and creating new ones. Fix this by keeping the destruction
process synchronous in regards to the user space process so IFF_UP can
be reliably set.
udp_tunnel_sock_release destroys vs->sock->sk if reference counter
indicates so. We expect to have the same lifetime of vxlan_sock and
vxlan_sock->sock->sk even in fast paths with only rcu locks held. So
only destruct the whole socket after we can be sure it cannot be found
by searching vxlan_net->sock_list.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jiri Benc <jbenc@redhat.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tested the PHY SGMII Loopback:
1.set the LOOPBACK bit,
2.set the autoneg to AUTONEG_DISABLE, it calls the
genphy_setup_forced which will clear the bit.
The BMCR_LOOPBACK bit should be preserved.
As Florian pointed out that other bits should be preserved too.
So I make the BMCR_ISOLATE and BMCR_PDOWN as well.
Signed-off-by: Weidong Wang <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Xin Long says:
====================
sctp: support sctp_diag in kernel
This patchset will add sctp_diag module to implement diag interface on
sctp in kernel.
For a listening sctp endpoint, we will just dump it's ep info.
For a sctp connection, we will the assoc info and it's ep info.
The ss dump will looks like:
[iproute2]# ./misc/ss --sctp -n -l
State Recv-Q Send-Q Local Address:Port Peer Address:Port
LISTEN 0 128 172.16.254.254:8888 *:*
LISTEN 0 5 127.0.0.1:1234 *:*
LISTEN 0 5 127.0.0.1:1234 *:*
- ESTAB 0 0 127.0.0.1%lo:1234 127.0.0.1:4321
LISTEN 0 128 172.16.254.254:8888 *:*
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.253.253:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.1.1:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.1.2:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.2.1:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.2.2:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.3.1:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.3.2:8888
LISTEN 0 0 127.0.0.1:4321 *:*
- ESTAB 0 0 127.0.0.1%lo:4321 127.0.0.1:1234
The entries with '- ESTAB' are the assocs, some of them may belong to
the same endpoint. So we will dump the parent endpoint first, like the
entry with 'LISTEN'. then dump the assocs. ep and assocs entries will
be dumped in right order so that ss can show them in tree format easily.
Besides, this patchset also simplifies sctp proc codes, cause it has
some similar codes with sctp diag in sctp transport traversal.
v1->v2:
1. inet_diag_get_handler needs to return it as const.
2. merge 5/7 into 2/7 of v1.
v2->v3:
do some improvements and fixes in patch 1-4, see the details in
each patch's comment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When rhashtable_walk_init return err, no release function should be
called, and when rhashtable_walk_start return err, we should only invoke
rhashtable_walk_exit to release the source.
But now when sctp_transport_walk_start return err, we just call
rhashtable_walk_stop/exit, and never care about if rhashtable_walk_init
or start return err, which is so bad.
We will fix it by calling rhashtable_walk_exit if rhashtable_walk_start
return err in sctp_transport_walk_start, and if sctp_transport_walk_start
return err, we do not need to call sctp_transport_walk_stop any more.
For sctp proc, we will use 'iter->start_fail' to decide if we will call
rhashtable_walk_stop/exit.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In sctp proc, these three functions in remaddrs and assocs are the
same. we should merge them into one.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This one will implement all the interface of inet_diag, inet_diag_handler.
which includes sctp_diag_dump, sctp_diag_dump_one and sctp_diag_get_info.
It will work as a module, and register inet_diag_handler when loading.
v2->v3:
- fix the mistake in inet_assoc_attr_size().
- change inet_diag_msg_laddrs_fill() name to inet_diag_msg_sctpladdrs_fill.
- change inet_diag_msg_paddrs_fill() name to inet_diag_msg_sctpaddrs_fill.
- add inet_diag_msg_sctpinfo_fill() to make asoc/ep fill code clearer.
- add inet_diag_msg_sctpasoc_fill() to make asoc fill code clearer.
- merge inet_asoc_diag_fill() and inet_ep_diag_fill() to
inet_sctp_diag_fill().
- call sctp_diag_get_info() directly, instead by handler, cause the caller
is in the same file with it.
- call lock_sock in sctp_tsp_dump_one() to make sure we call get sctp info
safely.
- after lock_sock(sk), we should check sk != assoc->base.sk.
- change mem[SK_MEMINFO_WMEM_ALLOC] to asoc->sndbuf_used for asoc dump when
asoc->ep->sndbuf_policy is set. don't use INET_DIAG_MEMINFO attr any more.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inet_diag_msg_common_fill is used to fill the diag msg common info,
we need to use it in sctp_diag as well, so export it.
inet_diag_msg_attrs_fill is used to fill some common attrs info between
sctp diag and tcp diag.
v2->v3:
- do not need to define and export inet_diag_get_handler any more.
cause all the functions in it are in sctp_diag.ko, we just call
them in sctp_diag.ko.
- add inet_diag_msg_attrs_fill to make codes clear.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some main variables in sctp.ko, we couldn't export it to other modules,
so we have to define some api to access them.
It will include sctp transport and endpoint's traversal.
There are some transport traversal functions for sctp_diag, we can also
use it for sctp_proc. cause they have the similar situation to traversal
transport.
v2->v3:
- rhashtable_walk_init need the parameter gfp, because of recent upstrem
update
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sctp_diag will dump some important details of sctp's assoc or ep, we use
sctp_info to describe them, sctp_get_sctp_info to get them, and export
it to sctp_diag.ko.
v2->v3:
- we will not use list_for_each_safe in sctp_get_sctp_info, cause
all the callers of it will use lock_sock.
- fix the holes in struct sctp_info with __reserved* field.
because sctp_diag is a new feature, and sctp_info is just for now,
it may be changed in the future.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCTP already serializes access to rcvbuf through its sock lock:
sctp_recvmsg takes it right in the start and release at the end, while
rx path will also take the lock before doing any socket processing. On
sctp_rcv() it will check if there is an user using the socket and, if
there is, it will queue incoming packets to the backlog. The backlog
processing will do the same. Even timers will do such check and
re-schedule if an user is using the socket.
Simplifying this will allow us to remove sctp_skb_list_tail and get ride
of some expensive lockings. The lists that it is used on are also
mangled with functions like __skb_queue_tail and __skb_unlink in the
same context, like on sctp_ulpq_tail_event() and sctp_clear_pd().
sctp_close() will also purge those while using only the sock lock.
Therefore the lockings performed by sctp_skb_list_tail() are not
necessary. This patch removes this function and replaces its calls with
just skb_queue_splice_tail_init() instead.
The biggest gain is at sctp_ulpq_tail_event(), because the events always
contain a list, even if it's queueing a single skb and this was
triggering expensive calls to spin_lock_irqsave/_irqrestore for every
data chunk received.
As SCTP will deliver each data chunk on a corresponding recvmsg, the
more effective the change will be.
Before this patch, with chunks with 30 bytes:
netperf -t SCTP_STREAM -H 192.168.1.2 -cC -l 60 -- -m 30 -S 400000
400000 -s 400000 400000
on a 10Gbit link with 1500 MTU:
SCTP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
425984 425984 30 60.00 137.45 7.34 7.36 52.504 52.608
With it:
SCTP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
425984 425984 30 60.00 179.10 7.97 6.70 43.740 36.788
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saeed Mahameed says:
====================
mlx5_core: mlx5_ifc updates
This series include mlx5_core updates for both net-next and rdma
trees for 4.7 kernel cycle. This is the only shared code planned
for 4.7 between rdma and net trees. Hopefully, this will prevent
future conflicts when merging between ib-next and net-next once
4.7 cycle is over and merge window is opened.
Both Mellanox rdma and net submissions will proceed once this series
is applied into both trees.
Future shared code will be sent to both maintainers as pull requests
from Mellanox's kernel.org tree.
We have included all the maintainers of respective drivers.
Kindly review the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding the needed mlx5_ifc hardware bits and structs
for the following feature:
* Add vport to steering commands for SRIOV ACL support
* Add mlcr, pcmr and mcia registers for dump module EEPROM
* Add support for FCS, baeacon led and disable_link bits to
hca caps
* Add CQE period mode bit in CQ context for CQE based CQ
moderation support
* Add umr SQ bit for fragmented memory registration
* Add needed bits and caps for Striding RQ support
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All reserved fields after early_vf_enable are off by 1, since
early_vf_enable was not explicitly declared as array of size 1.
Reserved field before cqe_zip had a wrong size, it should
be 0x80 + 0x3f.
Fixes: b0844444590e ("net/mlx5_core: Introduce access function to read internal timer ")
Fixes: b4ff3a36d3e4 ("net/mlx5: Use offset based reserved field names in the IFC header file")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Manish Chopra says:
====================
qed/qede: Add tunneling support
This patch series adds support for VXLAN, GRE and GENEVE tunnels
to be used over this driver. With this support, adapter can perform
TSO offload, inner/outer checksums offloads on TX and RX for
encapsulated packets.
V1->V2 [ Comments from Jesse Gross incorporated ]
* Drop general infrastructure change patch.
"net: Make vxlan/geneve default udp ports public"
* Remove by default Linux default UDP ports configurations in driver.
Instead, use general registration APIs for UDP port configurations
* Removing .ndo_features_check - we will add it later with proper change.
Please consider applying this series to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables netdev tunneling features and adds
TX/RX fastpath support for tunneling in driver.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables GENEVE tunnel on the adapter and
add support for driver hooks to configure UDP ports
for GENEVE tunnel offload to be performed by the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables VXLAN tunnel on the adapter and
add support for driver hooks to configure UDP ports
for VXLAN tunnel offload to be performed by the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds various structure/APIs needed to configure/enable different
tunnel [VXLAN/GRE/GENEVE] parameters on the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the newer version 1 of the HSR
networking standard. Version 0 is still default and the new
version has to be selected via iproute2.
Main changes are in the supervision frame handling and its
ethertype field.
Signed-off-by: Peter Heise <peter.heise@airbus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet says:
====================
tcp: final work on SYNFLOOD behavior
In the first patch, I remove the costly association of SYNACK+COOKIES
to a listener. I believe other parts of the stack should be ready.
The second patch removes a useless write into listener socket
in tcp_rcv_state_process(), incurring false sharing in
tcp_conn_request()
Performance under SYNFLOOD goes from 3.2 Mpps to 6 Mpps.
Test was using a single TCP listener, on a host with 8 RX queues
on the NIC, and 24 cores (48 ht)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Last known hot point during SYNFLOOD attack is the clearing
of rx_opt.saw_tstamp in tcp_rcv_state_process()
It is not needed for a listener, so we move it where it matters.
Performance while a SYNFLOOD hits a single listener socket
went from 5 Mpps to 6 Mpps on my test server (24 cores, 8 NIC RX queues)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When removing sk_refcnt manipulation on synflood, I missed that
using skb_set_owner_w() was racy, if sk->sk_wmem_alloc had already
transitioned to 0.
We should hold sk_refcnt instead, but this is a big deal under attack.
(Doing so increase performance from 3.2 Mpps to 3.8 Mpps only)
In this patch, I chose to not attach a socket to syncookies skb.
Performance is now 5 Mpps instead of 3.2 Mpps.
Following patch will remove last known false sharing in
tcp_rcv_state_process()
Fixes: 3b24d854cb35 ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace deprecated create_singlethread_workqueue with
alloc_ordered_workqueue.
Work items include getting tx/rx frame sizes, resetting MPI processor,
setting asic recovery bit so ordering seems necessary as only one work
item should be in queue/executing at any given time, hence the use of
alloc_ordered_workqueue.
WQ_MEM_RECLAIM flag has been set since ethernet devices seem to sit in
memory reclaim path, so to guarantee forward progress regardless of
memory pressure.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jon Maloy says:
====================
tipc: improvements to the link setup algorithm
This series addresses some smaller issues regarding the link setup
algorithm. The first commit fixes a rare bug we have discovered during
testing; the second one may have some future impact on cluster
scalabilty, while remaining ones can be regarded as cosmetic in
a wider sense of the word.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the link FSM, a received traffic packet can take a link
from state ESTABLISHING to ESTABLISHED, but the link can still not be
fully set up in one atomic operation. This means that even if the the
very first packet on the link is a traffic packet with sequence number
1 (one), it has to be dropped and retransmitted.
This can be avoided if we let the mentioned packet be preceded by a
LINK_PROTOCOL/STATE message, which takes up the endpoint before the
arrival of the traffic.
We add this small feature in this commit.
This is a fully compatible change.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some link establishment scenarios we see that packet #2 may be sent
out before packet #1, forcing the receiver to demand retransmission of
the missing packet. This is harmless, but may cause confusion among
people tracing the packet flow.
Since this is extremely easy to fix, we do so by adding en extra send
call to the bearer immediately after the link has come up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function tipc_link_timeout() is unnecessary complex, and can
easily be made more readable.
We do that with this commit. The only functional change is that we
remove a redundant test for whether the broadcast link is up or not.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link is down, it will continuously try to re-establish contact
with the peer by sending out a RESET or an ACTIVATE message at each
timeout interval. The default value for this interval is currently
375 ms. This is wasteful, and may become a problem in very large
clusters with dozens or hundreds of nodes being down simultaneously.
We now introduce a simple backoff algorithm for these cases. The
first five messages are sent at default rate; thereafter a message
is sent only each 16th timer interval.
This will cover the vast majority of link recycling cases, since the
endpoint starting last will transmit at the higher speed, and the link
should normally be established well be before the rate needs to be
reduced.
The only case where we will see a degradation of link re-establishment
times is when the endpoints remain intact, and a glitch in the
transmission media is causing the link reset. We will then experience
a worst-case re-establishing time of 6 seconds, something we deem
acceptable.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link endpoint is going down locally, e.g., because its interface
is being stopped, it will spontaneously send out a RESET message to
its peer, informing it about this fact. This saves the peer from
detecting the failure via probing, and hence gives both speedier and
less resource consuming failure detection on the peer side.
According to the link FSM, a receiver of a RESET message, ignoring the
reason for it, must now consider the sender ready to come back up, and
starts periodically sending out ACTIVATE messages to the peer in order
to re-establish the link. Also, according to the FSM, the receiver of
an ACTIVATE message can now go directly to state ESTABLISHED and start
sending regular traffic packets. This is a well-proven and robust FSM.
However, in the case of a reboot, there is a small possibilty that link
endpoint on the rebooted node may have been re-created with a new bearer
identity between the moment it sent its (pre-boot) RESET and the moment
it receives the ACTIVATE from the peer. The new bearer identity cannot
be known by the peer according to this scenario, since traffic headers
don't convey such information. This is a problem, because both endpoints
need to know the correct value of the peer's bearer id at any moment in
time in order to be able to produce correct link events for their users.
The only way to guarantee this is to enforce a full setup message
exchange (RESET + ACTIVATE) even after the reboot, since those messages
carry the bearer idientity in their header.
In this commit we do this by introducing and setting a "stopping" bit in
the header of the spontaneously generated RESET messages, informing the
peer that the sender will not be immediately ready to re-establish the
link. A receiver seeing this bit must act as if this were a locally
detected connectivity failure, and hence has to go through a full two-
way setup message exchange before any link can be re-established.
Although never reported, this problem seems to have always been around.
This protocol addition is fully backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
mlxsw: spectrum_buffers: couple of cosmetic patches
As suggested by David Laight
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: bf7974710a40 ("devlink: add shared buffer configuration")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the tun device accounting uses dev->stats without applying any
kind of protection, regardless that accounting happens in preemptible
process context.
This patch move the tun stats to a per cpu data structure, and protect
the updates with u64_stats_update_begin()/u64_stats_update_end() or
this_cpu_inc according to the stat type. The per cpu stats are
aggregated by the newly added ndo_get_stats64 ops.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge branch 'bpf-ARG_PTR_TO_RAW_STACK'
Daniel Borkmann says:
====================
BPF updates
This series adds a new verifier argument type called
ARG_PTR_TO_RAW_STACK and converts related helpers to make
use of it. Basic idea is that we can save init of stack
memory when the helper function is guaranteed to fully
fill out the passed buffer in every path. Series also adds
test cases and converts samples. For more details, please
see individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds test cases mostly around ARG_PTR_TO_RAW_STACK to check the
verifier behaviour.
[...]
#84 raw_stack: no skb_load_bytes OK
#85 raw_stack: skb_load_bytes, no init OK
#86 raw_stack: skb_load_bytes, init OK
#87 raw_stack: skb_load_bytes, spilled regs around bounds OK
#88 raw_stack: skb_load_bytes, spilled regs corruption OK
#89 raw_stack: skb_load_bytes, spilled regs corruption 2 OK
#90 raw_stack: skb_load_bytes, spilled regs + data OK
#91 raw_stack: skb_load_bytes, invalid access 1 OK
#92 raw_stack: skb_load_bytes, invalid access 2 OK
#93 raw_stack: skb_load_bytes, invalid access 3 OK
#94 raw_stack: skb_load_bytes, invalid access 4 OK
#95 raw_stack: skb_load_bytes, invalid access 5 OK
#96 raw_stack: skb_load_bytes, invalid access 6 OK
#97 raw_stack: skb_load_bytes, large access OK
Summary: 98 PASSED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the zero initialization in the sample programs where appropriate.
Note that this is an optimization which is now possible, old programs
still doing the zero initialization are just fine as well. Also, make
sure we don't have padding issues when we don't memset() the entire
struct anymore.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts all helpers that can use ARG_PTR_TO_RAW_STACK as argument
type. For tc programs this is bpf_skb_load_bytes(), bpf_skb_get_tunnel_key(),
bpf_skb_get_tunnel_opt(). For tracing, this optimizes bpf_get_current_comm()
and bpf_probe_read(). The check in bpf_skb_load_bytes() for MAX_BPF_STACK can
also be removed since the verifier already makes sure we stay within bounds
on stack buffers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When passing buffers from eBPF stack space into a helper function, we have
ARG_PTR_TO_STACK argument type for helpers available. The verifier makes sure
that such buffers are initialized, within boundaries, etc.
However, the downside with this is that we have a couple of helper functions
such as bpf_skb_load_bytes() that fill out the passed buffer in the expected
success case anyway, so zero initializing them prior to the helper call is
unneeded/wasted instructions in the eBPF program that can be avoided.
Therefore, add a new helper function argument type called ARG_PTR_TO_RAW_STACK.
The idea is to skip the STACK_MISC check in check_stack_boundary() and color
the related stack slots as STACK_MISC after we checked all call arguments.
Helper functions using ARG_PTR_TO_RAW_STACK must make sure that every path of
the helper function will fill the provided buffer area, so that we cannot leak
any uninitialized stack memory. This f.e. means that error paths need to
memset() the buffers, but the expected fast-path doesn't have to do this
anymore.
Since there's no such helper needing more than at most one ARG_PTR_TO_RAW_STACK
argument, we can keep it simple and don't need to check for multiple areas.
Should in future such a use-case really appear, we have check_raw_mode() that
will make sure we implement support for it first.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when the verifier checks calls in check_call() function, we
call check_func_arg() for all 5 arguments e.g. to make sure expected types
are correct. In some cases, we collect meta data (here: map pointer) to
perform additional checks such as checking stack boundary on key/value
sizes for subsequent arguments. As we're going to extend the meta data,
add a generic struct bpf_call_arg_meta that we can use for passing into
check_func_arg().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds what's missing to properly support RPS and RFS on SCTP,
as some of it is already implemented in common calls.
Having support for RPS and RFS allows better scaling specially because
not all NICs support hashing SCTP headers.
Save the hash right when we dequeue a skb from inqueue so we do it only
once per skb instead of per chunk. New sockets will then inherit the
hash through sctp_copy_sock().
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skbs given to validate_xmit_skb() should not have a next
pointer anymore.
Also if a packet is dropped, increment dev->tx_dropped
__dev_queue_xmit() no longer has to change tx_dropped in this case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
consume_skb() isn't for error cases that kfree_skb() is more proper
one. At this patch, it fixed tpacket_rcv() and packet_rcv() to be
consistent for error or non-error cases letting perf trace its event
properly.
Signed-off-by: Weongyo Jeong <weongyo.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, the requests sent to topology server are queued
to a workqueue by the generic server framework.
These messages are processed by worker threads and trigger the
registered callbacks.
To reduce latency on uniprocessor systems, explicit rescheduling
is performed using cond_resched() after MAX_RECV_MSG_COUNT(25)
messages.
This implementation on SMP systems leads to an subscriber refcnt
error as described below:
When a worker thread yields by calling cond_resched() in a SMP
system, a new worker is created on another CPU to process the
pending workitem. Sometimes the sleeping thread wakes up before
the new thread finishes execution.
This breaks the assumption on ordering and being single threaded.
The fault is more frequent when MAX_RECV_MSG_COUNT is lowered.
If the first thread was processing subscription create and the
second thread processing close(), the close request will free
the subscriber and the create request oops as follows:
[31.224137] WARNING: CPU: 2 PID: 266 at include/linux/kref.h:46 tipc_subscrb_rcv_cb+0x317/0x380 [tipc]
[31.228143] CPU: 2 PID: 266 Comm: kworker/u8:1 Not tainted 4.5.0+ #97
[31.228377] Workqueue: tipc_rcv tipc_recv_work [tipc]
[...]
[31.228377] Call Trace:
[31.228377] [<ffffffff812fbb6b>] dump_stack+0x4d/0x72
[31.228377] [<ffffffff8105a311>] __warn+0xd1/0xf0
[31.228377] [<ffffffff8105a3fd>] warn_slowpath_null+0x1d/0x20
[31.228377] [<ffffffffa0098067>] tipc_subscrb_rcv_cb+0x317/0x380 [tipc]
[31.228377] [<ffffffffa00a4984>] tipc_receive_from_sock+0xd4/0x130 [tipc]
[31.228377] [<ffffffffa00a439b>] tipc_recv_work+0x2b/0x50 [tipc]
[31.228377] [<ffffffff81071925>] process_one_work+0x145/0x3d0
[31.246554] ---[ end trace c3882c9baa05a4fd ]---
[31.248327] BUG: spinlock bad magic on CPU#2, kworker/u8:1/266
[31.249119] BUG: unable to handle kernel NULL pointer dereference at 0000000000000428
[31.249323] IP: [<ffffffff81099d0c>] spin_dump+0x5c/0xe0
[31.249323] PGD 0
[31.249323] Oops: 0000 [#1] SMP
In this commit, we
- rename tipc_conn_shutdown() to tipc_conn_release().
- move connection release callback execution from tipc_close_conn()
to a new function tipc_sock_release(), which is executed before
we free the connection.
Thus we release the subscriber during connection release procedure
rather than connection shutdown procedure.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
