summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2020-05-25usb: gadget: f_tcm: Inform last stream requestThinh Nguyen
Set the request->is_last to each stream request to indicate that the request is the last stream request of a transfer. The DWC3 controller needs to know this info to properly switch streams. The current implementation of f_tcm uses a single request per transfer, so every stream request is the last of its stream. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: Introduce usb_request->is_lastThinh Nguyen
To take advantage of DWC3 internal TRB prefetch and cache for performance, inform the controller the last request with stream_id before switching to a different stream transfer. This allows the controller to maintain its transfer burst within the stream ID. Introduce the usb-request is_last field to help inform the DWC3 controller of this. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: dwc3: Get MDWIDTH for DWC_usb32Thinh Nguyen
DWC_usb32 supports MDWIDTH value larger than 255 and up to 1023. The field HWPARAMS6[9:8] stores the upper 2-bit values of the DWC_usb32's MDWIDTH. Check that parameter and properly get the MDWIDTH for DWC_usb32. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: dwc3: Add support for DWC_usb32 IPThinh Nguyen
Synopsys introduces a new controller DWC_usb32. It supports dual-lane and speed up to 20 Gbps, and the DWC3 driver will drive this controller. Currently the driver uses a single field dwc->revision to ID both DWC_usb3 and DWC_usb31 and their version number. This was sufficient for two IPs, but this method doesn't work with additional IPs. As a result, let's separate the dwc->revision field to 2 separate fields: ip and revision. The ip field now stores the ID of the controller's IP while the revision field stores the controller's version number. This new scheme enforces DWC3 to compare the revision within the same IP only. As a result, we must update all the revision check of the controller to check its corresponding IP. To help with this enforcement, we create a few macros to help with the common version checks: DWC3_IP_IS(IP) DWC3_VER_IS(IP, VERSION) DWC3_VER_IS_PRIOR(IP, VERSION) DWC3_VER_IS_WITHIN(IP, LOWER_VERSION, UPPER_VERSION) DWC3_VER_TYPE_IS_WITHIN(IP, VERSION, LOWER_VERSION_TYPE, UPPER_VERSION_TYPE) The DWC_usb32 controller operates using the same programming model and with very similar configurations as its previous controllers. Please note that the various IP and revision checks in this patch match the current checks for DWC_usb31 version 1.90a. Additional configurations that are unique to DWC_usb32 are applied separately. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: tegra-xudc: add port_speed_quirkNagarjuna Kristam
OTG port on Tegra194 supports GEN1 speeds when in device mode and GEN2 speeds when in host mode. dd port_speed_quirk that configures port to GEN1/GEN2 speds, corresponding to the mode. Based on work by WayneChang <waynec@nvidia.com> Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: tegra-xudc: Add Tegra194 supportNagarjuna Kristam
This commit adds support for XUSB device mode controller support on Tegra194 SoC. This is very similar to the existing Tegra186 XUDC, with lpm support added in addition. Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25dt-bindings: usb: tegra-xudc: Add Tegra194 XUSB controller supportNagarjuna Kristam
Extend the Tegra XUSB controller device tree binding with Tegra194 support. Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25USB: dummy-hcd: Add missing annotation for set_link_state()Jules Irenge
Sparse reports a warning at set_link_state() warning: context imbalance in set_link_state() - unexpected unlock The root cause is the missing annotation at set_link_state() Add the missing __must_hold(&dum->lock) Signed-off-by: Jules Irenge <jbi.octave@gmail.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: Add missing annotation for xudc_handle_setup()Jules Irenge
Sparse reports a warning at xudc_handle_setup() warning: context imbalance in xudc_handle_setup() - unexpected unlock The root cause is the missing annotation at xudc_handle_setup() Add the missing __must_hold(&udc->lock) annotation Signed-off-by: Jules Irenge <jbi.octave@gmail.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: mass_storage: use module_usb_composite_driver to simplify the codeWei Yongjun
module_usb_composite_driver() makes the code simpler by eliminating boilerplate code. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: omap_udc: remove unneeded semicolonJason Yan
Fix the following coccicheck warning: drivers/usb/gadget/udc/omap_udc.c:2579:2-3: Unneeded semicolon Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: udc: remove comparison to bool in mv_u3d_core.cJason Yan
Fix the following coccicheck warning: drivers/usb/gadget/udc/mv_u3d_core.c:1551:5-13: WARNING: Comparison to bool Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: net2272: use false for 'use_dma'Jason Yan
Fix the following coccicheck warning: drivers/usb/gadget/udc/net2272.c:57:12-19: WARNING: Assignment of 0/1 to bool variable Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: dwc3: use true,false for dwc->otg_restart_hostJason Yan
Fix the following coccicheck warning: drivers/usb/dwc3/drd.c:85:3-24: WARNING: Assignment of 0/1 to bool variable drivers/usb/dwc3/drd.c:59:2-23: WARNING: Assignment of 0/1 to bool variable Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: function: remove redundant assignment to variable 'status'Colin Ian King
The variable status is being assigned a value that is never read and it is being updated later with a new value. The assignment is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25USB: gadget: udc: s3c2410_udc: Remove pointless NULL check in s3c2410_udc_nukeNathan Chancellor
Clang warns: drivers/usb/gadget/udc/s3c2410_udc.c:255:11: warning: comparison of address of 'ep->queue' equal to a null pointer is always false [-Wtautological-pointer-compare] if (&ep->queue == NULL) ~~~~^~~~~ ~~~~ 1 warning generated. It is not wrong, queue is not a pointer so if ep is not NULL, the address of queue cannot be NULL. No other driver does a check like this and this check has been around since the driver was first introduced, presumably with no issues so it does not seem like this check should be something else. Just remove it. Commit afe956c577b2d ("kbuild: Enable -Wtautological-compare") exposed this but it is not the root cause of the warning. Fixes: 3fc154b6b8134 ("USB Gadget driver for Samsung s3c2410 ARM SoC") Link: https://github.com/ClangBuiltLinux/linux/issues/1004 Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: f_acm: add suspend resume callbacksFabrice Gasnier
Add suspend resume callbacks to notify u_serial of the bus suspend/resume state. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: f_serial: add suspend resume callbacksFabrice Gasnier
Add suspend resume callbacks to notify u_serial of the bus suspend/resume state. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: u_serial: add suspend resume callbacksFabrice Gasnier
Add suspend resume callbacks to handle the case seen when the bus is suspended by the HOST, and the device opens the port (cat /dev/ttyGS0). Gadget controller (like DWC2) doesn't accept usb requests to be queued in this case (when in L2 state), from the gs_open() call. Error log is printed - configfs-gadget gadget: acm ttyGS0 can't notify serial state, -11 If the HOST resumes (opens) the bus, the port still isn't functional. Use suspend/resume callbacks to monitor the gadget suspended state by using 'suspended' flag. In case the port gets opened (cat /dev/ttyGS0), the I/O stream will be delayed until the bus gets resumed by the HOST. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: dwc2: gadget: move gadget resume after the core is in L0 stateFabrice Gasnier
When the remote wakeup interrupt is triggered, lx_state is resumed from L2 to L0 state. But when the gadget resume is called, lx_state is still L2. This prevents the resume callback to queue any request. Any attempt to queue a request from resume callback will result in: - "submit request only in active state" debug message to be issued - dwc2_hsotg_ep_queue() returns -EAGAIN Call the gadget resume routine after the core is in L0 state. Fixes: f81f46e1f530 ("usb: dwc2: implement hibernation during bus suspend/resume") Acked-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: uvc_video: add worker to handle the frame pumpingMichael Grzeschik
This patch changes the function uvc_video_pump to be a separate scheduled worker. This way the completion handler of each usb request and every direct caller of the pump has only to schedule the worker instead of doing the request handling by itself. Moving the request handling to one thread solves the locking problems between the three queueing cases in the completion handler, v4l2_qbuf and video_enable. Many drivers handle the completion handlers directly in their interrupt handlers. This patch also reduces the workload on each interrupt. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: renesas_usbhs: Use the correct style for SPDX License IdentifierNishad Kamdar
This patch corrects the SPDX License Identifier style in header files related to Renesas USBHS Controller Drivers. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used). Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: f_fs: remove unneeded semicolon in __ffs_data_got_descs()Jason Yan
Fix the following coccicheck warning: drivers/usb/gadget/function/f_fs.c:2507:2-3: Unneeded semicolon Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25dt-bindings: usb: dwc3: remove old DWC3 wrapperMartin Blumenstingl
There is now an updated bindings for these SoCs making the old compatible obsolete. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25doc: dt: bindings: usb: dwc3: remove amlogic compatible entriesNeil Armstrong
Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: dwc3: of-simple: remove Amlogic GXL and AXG compatiblesMartin Blumenstingl
There is now a dedicated driver for these SoCs making the old compatible obsolete. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25phy: amlogic: meson-gxl-usb3: remove code for non-existing PHYMartin Blumenstingl
The registers which are managed by the meson-gxl-usb3 PHY driver are actually "USB control" registers (which are "glue" registers which manage OTG detection and routing of the OTG capable port between the DWC2 peripheral-only controller and the DWC3 host-only controller). Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-g12a-usb driver supports the USB control registers on GXL and GXM SoCs (these were previously managed by the meson-gxl-usb3 PHY driver). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25arm64: dts: amlogic: use the new USB control driver for GXL and GXMMartin Blumenstingl
Add the correcly architectured USB Glue node and adapt all the Amlogic GXL and GXM board to the new organization. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: dwc3: meson-g12a: add support for GXL and GXM SoCsNeil Armstrong
In order to add support for the Amlogic GXL/GXM USB Glue, this adds the corresponding : - PHY names - clock names - USB2 PHY init and mode set - regmap setup Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: dwc3: meson-g12a: support the GXL/GXM DWC3 host phy disconnectNeil Armstrong
On the Amlogic GXL/GXM SoCs, the OTG PHY status signals are always connected to the DWC3 controller, thus crashing the controller when switching to OTG mode when port is not populated with a device/cable to Host. Amlogic added a bit to disconnect the OTG PHY status signals from the DWC3 to be used when switching the OTG PHY as Device to the DWC2 controller. The drawback is that it makes the DWC3 port state machine stall and needs a full reset of the DWC3 controller to get connect status to the port connected to the OTG PHY, but not the other one. Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: dwc3: meson-g12a: refactor usb initNeil Armstrong
Refactor the USB init code patch to handle the Amlogic GXL/GXM needing to initialize the OTG port as Peripheral mode for the DWC2 IP to probe correctly. A secondary, post_init callback is added to setup the OTG PHY mode after powering up the PHYs and before probing the DWC2 and DWC3 controllers. Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: udc: remove unused 'driver_desc'Jason Yan
Fix the following gcc warning: drivers/usb/gadget/udc/gr_udc.c:51:19: warning: ‘driver_desc’ defined but not used [-Wunused-const-variable=] static const char driver_desc[] = DRIVER_DESC; ^~~~~~~~~~~ Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: max3420: Add a missing '\n' in a log messageChristophe JAILLET
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'. Fixes: 48ba02b2e2b1 ("usb: gadget: add udc driver for max3420") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25USB: mtu3: Use the correct style for SPDX License IdentifierNishad Kamdar
This patch corrects the SPDX License Identifier style in header files related to MediaTek USB3 Dual Role controller. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used). Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: cdns3: change dev_info to dev_dbg for debug messagePeter Chen
During device mode initialization, lots of device information are printed to console, see below. Change them as debug message. cdns-usb3 5b130000.cdns3: Initialized ep0 support: cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: cdns3: change "cdsn3" to"cdns3"Peter Chen
And delete cdsn3_hw_role_state_machine declare which doesn't be needed. Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: cdns3: delete role_overridePeter Chen
In short, we have three kinds of role switches: - Based on SoC: ID and VBUS - Based on external connnctor, eg, Type-C or GPIO Connector - Based on user choices through sysfs Since HW handling and usb-role-switch handling are at different places, we do not need role_override any more, and this flag could not judge external connector case well. With role_override deleted, We use cdns3_hw_role_switch for the 1st use case, and usb-role-switch for the 2nd and 3rd cases. Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: cdns3: core: get role switch node from firmwarePeter Chen
After that, the role switch device (eg, Type-C device) could call cdns3_role_set to finish the role switch. Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: dwc3: gadget: Continue to process pending requestsThinh Nguyen
If there are still pending requests because no TRB was available, prepare more when started requests are completed. Introduce dwc3_gadget_ep_should_continue() to check for incomplete and pending requests to resume updating new TRBs to the controller's TRB cache. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-25usb: gadget: tegra-xudc: Add vbus_draw supportNagarjuna Kristam
Register vbus_draw to gadget ops and update corresponding vbus draw current to usb_phy. Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-05usb: dwc3: gadget: WARN on no-resource statusThinh Nguyen
If the driver issued START_TRANSFER and received a no-resource status, then generally there are a few reasons for this: 1) The driver did not allocate resource for the endpoint during power-on-reset initialization. 2) The transfer resource was reset. At this moment, we don't do this in the driver, but it occurs when the driver issues START_CONFIG cmd to ep0 with resource index=2. 3) The driver issues the START_TRANSFER command to an already started endpoint. Usually, this is because the END_TRANSFER command hasn't completed yet. Print out a warning to help debug this issue in the driver. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-05usb: dwc3: gadget: Issue END_TRANSFER to retry isoc transferThinh Nguyen
After a number of unsuccessful start isoc attempts due to bus-expiry status, issue END_TRANSFER command and retry on the next XferNotReady event. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-05usb: dwc3: gadget: Store resource index of start cmdThinh Nguyen
As long as the START_TRANSFER command completes, it provides the resource index of the endpoint. Use this when we need to issue END_TRANSFER command to an isoc endpoint to retry with a new XferNotReady event. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-05usb: dwc3: gadget: Properly handle failed kick_transferThinh Nguyen
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we should properly end an active transfer and give back all the started requests. However if it's for an isoc endpoint, the failure maybe due to bus-expiry status. In this case, don't give back the requests and wait for the next retry. Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-05usb: dwc3: core: Use role-switch default dr_modeThinh Nguyen
If the driver is configured to use DRD role-switch, let the drd code path decide the default dr_mode. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-05usb: dwc3: drd: Don't free non-existing irqThinh Nguyen
If the driver is configured to use DRD role-switch, it's not OTG. There won't be OTG irq to free. Check for dwc->otg_irq before freeing it. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-05usb: dwc3: meson-g12a: refactor usb2 phy initNeil Armstrong
Refactor the USB2 PHY init code patch to handle the Amlogic GXL/GXM not having the PHY mode control registers in the Glue but in the PHY registers. The Amlogic GXL/GXM will call phy_set_mode() instead of programming the PHY mode control registers, thus add two new callbacks to the SoC match data. Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-05usb: dwc3: meson-g12a: check return of dwc3_meson_g12a_usb_initNeil Armstrong
The dwc3_meson_g12a_usb_init function can return an error, check it. Fixes: c99993376f72ca ("usb: dwc3: Add Amlogic G12A DWC3 glue") Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-05usb: dwc3: meson-g12a: get the reset as sharedNeil Armstrong
In order to support the Amlogic GXL/GXM SoCs, the reset line must be handled as shared since also used by the PHYs. Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-05-05usb: dwc3: meson-g12a: handle the phy and glue registers separatelyNeil Armstrong
On the Amlogic GXL/GXM SoCs, only the USB control registers are available, the PHY mode being handled in the PHY registers. Thus, handle the PHY mode registers in separate regmaps and prepare support for Amlogic GXL/GXM SoCs by moving the regmap setup in a callback set in the SoC match data. Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-10 10:51:02 +0000