| Age | Commit message (Collapse) | Author |
|---|
|
Writes into voltage limit attributes can overflow due to an unbound
multiplication.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix overflows seen when writing voltage and temperature limit attributes.
The value passed to DIV_ROUND_CLOSEST() needs to be clamped, and the
value parameter passed to nct7802_write_fan_min() is an unsigned long.
Also, writing values larger than 2700000 into a fan limit attribute results
in writing 0 into the chip's limit registers. The exact behavior when
writing this value is unspecified. For consistency, report a limit of
1350000 if the chip register reads 0. This may be wrong, and the chip
behavior should be verified with the actual chip, but it is better than
reporting a value of 0 (which, when written, results in writing a value
of 0x1fff into the chip register).
Fixes: 3434f3783580 ("hwmon: Driver for Nuvoton NCT7802Y")
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix overflows seen when writing large values into various temperature limit
attributes.
The input value passed to DIV_ROUND_CLOSEST() needs to be clamped to avoid
such overflows.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix overflows seen when writing large values into temperature limit,
voltage limit, and pwm hysteresis attributes.
The input parameter to DIV_ROUND_CLOSEST() needs to be clamped to avoid
such overflows.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix overflows seen when writing large values into voltage limit,
temperature limit, temperature offset, and DAC attributes.
Overflows are seen due to unbound multiplications and additions.
While at it, change the low temperature limit to -128 degrees C,
since this is the minimum temperature accepted by the chip.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Writes into voltage limit attributes can overflow due to an unbound
multiplication.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Install the callbacks via the state machine and let the core invoke the
callbacks on the already online CPUs. When the hotplug state is
unregistered the cleanup function is called for each cpu. So both cpu loops
in init() and exit() are not longer required.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Simple hwmon binding documentation.
Signed-off-by: John Muir <john@jmuir.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the TI TMP108 temperature sensor with some device
configuration parameters.
Signed-off-by: John Muir <john@jmuir.com>
[groeck: Initialize of_match_table]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Allocating the sysfs attribute name only if needed and only with the
required minimum length looks optimal, but does not take the additional
overhead for both devm_ data structures and the allocation header itself
into account. This also results in unnecessary memory fragmentation.
Move the sysfs name string into struct hwmon_device_attribute and give it
a sufficient length to reduce this overhead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The 'groups' parameter of hwmon_device_register_with_info() and
devm_hwmon_device_register_with_info() is only necessary if extra
non-standard attributes need to be provided. Rename the parameter
to extra_groups and clarify the documentation.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
A list of sysfs attribute groups is NULL-terminated, so we always need
to allocate data for at least two groups (the dynamically generated group
plus the NULL pointer). Add a comment to explain the situation.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The is_visible callback provides the sysfs attribute mode and is thus
truly mandatory as documented. Check it once at registration and remove
other checks for its existence.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Inform the user that hwmon_device_register() is deprecated,
and suggest conversion to the newest API. Also remove
hwmon_device_register() from the kernel API documentation.
Note that hwmon_device_register() is not marked as __deprecated()
since doing so might result in build errors.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Describing chip attributes as "attributes which apply to the entire chip"
is confusing. Rephrase to "attributes which are not bound to a specific
input or output".
Also rename hwmon_chip_attr_templates[] to hwmon_chip_attrs[] to indicate
that the respective strings strings are not templates but actual attribute
names.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The new API is so far only suited for data attributes and does not work
well for string attributes, specifically for the 'label' attributes.
Provide a separate callback function for those.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The callback descrption in hwmon.h was misleading and stated that read and
write callbacks would be optional. More accurate is is that the callbacks
are mandatory if readable / writeable attributes are present.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The lm90 driver also supports the Texas Instruments TMP451 sensor chip.
Since the Kconfig description for the driver includes a list of all
compatible chips, mention the TI TMP451 there as well.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Keeping track of the per package platform devices requires an extra object,
which is held in a linked list.
The maximum number of packages is known at init() time. So the extra object
and linked list management can be replaced by an array of platform device
pointers in which the per package devices pointers can be stored. Lookup
becomes a simple array lookup instead of a list walk.
The mutex protecting the list can be removed as well because the array is
only accessed from cpu hotplug callbacks which are already serialized.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The cpu online callback returns success unconditionally even when the
device has no support, micro code mismatches or device allocation fails.
Only if CPU_HOTPLUG is disabled, the init function checks whether the
device list is empty and removes the driver.
This does not make sense. If CPU HOTPLUG is enabled then there is no point
to keep the driver around when it failed to initialize on the already
online cpus. The chance that not yet online CPUs will provide a functional
interface later is very close to zero.
Add proper error return codes, so the setup of the cpu hotplug states fails
when the device cannot be initialized and remove all the magic cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Install the callbacks via the state machine. Setup and teardown are handled
by the hotplug core.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-hwmon@vger.kernel.org
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: rt@linuxtronix.de
Cc: Guenter Roeck <linux@roeck-us.net>
Link: http://lkml.kernel.org/r/20161117183541.8588-5-bigeasy@linutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
No point in looking up the same thing over and over.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The coretemp driver provides a sysfs interface per physical core. If
hyperthreading is enabled and one of the siblings goes offline the sysfs
interface is removed and then immeditately created again for the
sibling. The only difference of them is the target cpu for the
rdmsr_on_cpu() in the sysfs show functions.
It's way simpler to keep a cpumask of cpus which are active in a package
and only remove the interface when the last sibling goes offline. Otherwise
just move the target cpu for the sysfs show functions to the still online
sibling.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When a CPU is offlined nothing checks whether it is the target CPU for the
package temperature sysfs interface.
As a consequence all future readouts of the package temperature return
crap:
90000
which is Tjmax of that package.
Check whether the outgoing CPU is the target for the package and assign it
to some other still online CPU in the package. Protect the change against
the rdmsr_on_cpu() in show_crit_alarm().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Module test reports overflows when writing into temperature and voltage
limit attributes
temp1_min: Suspected overflow: [127000 vs. 0]
temp1_max: Suspected overflow: [127000 vs. 0]
temp1_offset: Suspected overflow: [127000 vs. 0]
temp2_min: Suspected overflow: [127000 vs. 0]
temp2_max: Suspected overflow: [127000 vs. 0]
temp2_offset: Suspected overflow: [127000 vs. 0]
temp3_min: Suspected overflow: [127000 vs. 0]
temp3_max: Suspected overflow: [127000 vs. 0]
temp3_offset: Suspected overflow: [127000 vs. 0]
in0_min: Suspected overflow: [3320 vs. 0]
in0_max: Suspected overflow: [3320 vs. 0]
in4_min: Suspected overflow: [15938 vs. 0]
in4_max: Suspected overflow: [15938 vs. 0]
in6_min: Suspected overflow: [1992 vs. 0]
in6_max: Suspected overflow: [1992 vs. 0]
in7_min: Suspected overflow: [2391 vs. 0]
in7_max: Suspected overflow: [2391 vs. 0]
The problem is caused by conversions from unsigned long to long and
from long to int.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Module test reports:
temp1_max: Suspected overflow: [160000 vs. 0]
temp1_min: Suspected overflow: [160000 vs. 0]
This is seen because the values passed when writing temperature limits
are unbound.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Fixes: 6099469805c2 ("hwmon: Support for Dallas Semiconductor DS620")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Module test reports:
in0_min: Suspected overflow: [3320 vs. 0]
in0_max: Suspected overflow: [3320 vs. 0]
in4_min: Suspected overflow: [15938 vs. 0]
in4_max: Suspected overflow: [15938 vs. 0]
temp1_max: Suspected overflow: [127000 vs. 0]
temp1_max_hyst: Suspected overflow: [127000 vs. 0]
aout_output: Suspected overflow: [1250 vs. 0]
Code analysis reveals that the overflows are caused by conversions
from unsigned long to long to int, combined with multiplications on
passed values.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This is also a preparation for to support more properties like min, max and
alarm.
Signed-off-by: Michael Walle <michael@walle.cc>
[groeck: Minor alignment changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The check loop for the cpu type is pointless as we already have a cpu model
match before that. The only thing which is not covered by that check would
be a smp system with two different cores. Not likely to happen.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Support setting the reference voltage from the device tree.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Replace S_IRUGO with the better readable 0444.
This fixes a checkpatch warning.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Document the devicetree bindings for the Microchip MCP3021/3221.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This is the expected thing for a hwmon driver to do, this changes
the sysfs paths from, say:
/sys/bus/i2c/devices/0-002c/temp1_input
to:
/sys/bus/i2c/devices/0-002c/hwmon/hwmon0/temp1_input
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The adm1278 can optionally monitor the VOUT pin. This functionality is
not enabled at reset, so PMON_CONFIG needs to be modified in order to
enable it.
Signed-off-by: Yi Li <adamliyi@msn.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the tc654 and tc655 fan controllers from Microchip.
http://ww1.microchip.com/downloads/en/DeviceDoc/20001734C.pdf
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
[groeck: Fixed continuation line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Converts the unsigned temperature values from the i2c read
to be sign extended as defined in the datasheet so that
negative temperatures are properly read.
Fixes: 28e6274d8fa67 ("hwmon: (amc6821) Avoid forward declaration")
Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
Signed-off-by: Matt Weber <matthew.weber@rockwellcollins.com>
[groeck: Dropped unnecessary continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/hwmon/scpi-hwmon.ko | grep alias
$
After this patch:
$ modinfo drivers/hwmon/scpi-hwmon.ko | grep alias
alias: of:N*T*Carm,scpi-sensorsC*
alias: of:N*T*Carm,scpi-sensors
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Fixes: ea98b29a05e9c ("hwmon: Support sensors exported via ARM SCP interface")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
Pull IOMMU fixes from David Woodhouse:
"Two minor fixes.
The first fixes the assignment of SR-IOV virtual functions to the
correct IOMMU unit, and the second fixes the excessively large (and
physically contiguous) PASID tables used with SVM"
* git://git.infradead.org/intel-iommu:
iommu/vt-d: Fix PASID table allocation
iommu/vt-d: Fix IOMMU lookup for SR-IOV Virtual Functions
|
|
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.9:
- Fix unreadable output in __do_page_fault due to the KERN_CONT
patchset
- Correctly handle MIPS R6 fixes to the c0_wired register"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: mm: Fix output of __do_page_fault
MIPS: Mask out limit field when calculating wired entry count
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs splice fix from Al Viro.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix default_file_splice_read()
|
|
Botched calculation of number of pages. As the result,
we were dropping pieces when doing splice to pipe from
e.g. 9p.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here is a revert and two bugfixes for the I2C designware driver.
Please note that we are still hunting down a regression for the
i2c-octeon driver. While there is a fix pending, we have unclear
feedback from the testers currently. An rc8 would be quite helpful
for this case"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: designware: do not disable adapter after transfer"
i2c: designware: fix rx fifo depth tracking
i2c: designware: report short transfers
|
|
Pull ARM fix from Russell King:
"This resolves the ksyms issues by reverting the commit which
introduced the breakage"
There was what I consider to be a better fix, but it's late in the rc
game, so I'll take the revert.
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
Revert "arm: move exports to definitions"
|
|
Pull networking fixes from David Miller:
1) Fix leak in fsl/fman driver, from Dan Carpenter.
2) Call flow dissector initcall earlier than any networking driver can
register and start to use it, from Eric Dumazet.
3) Some dup header fixes from Geliang Tang.
4) TIPC link monitoring compat fix from Jon Paul Maloy.
5) Link changes require EEE re-negotiation in bcm_sf2 driver, from
Florian Fainelli.
6) Fix bogus handle ID passed into tfilter_notify_chain(), from Roman
Mashak.
7) Fix dump size calculation in rtnl_calcit(), from Zhang Shengju.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
tipc: resolve connection flow control compatibility problem
mvpp2: use correct size for memset
net/mlx5: drop duplicate header delay.h
net: ieee802154: drop duplicate header delay.h
ibmvnic: drop duplicate header seq_file.h
fsl/fman: fix a leak in tgec_free()
net: ethtool: don't require CAP_NET_ADMIN for ETHTOOL_GLINKSETTINGS
tipc: improve sanity check for received domain records
tipc: fix compatibility bug in link monitoring
net: ethernet: mvneta: Remove IFF_UNICAST_FLT which is not implemented
dwc_eth_qos: drop duplicate headers
net sched filters: fix filter handle ID in tfilter_notify_chain()
net: dsa: bcm_sf2: Ensure we re-negotiate EEE during after link change
bnxt: do not busy-poll when link is down
udplite: call proper backlog handlers
ipv6: bump genid when the IFA_F_TENTATIVE flag is clear
net/mlx4_en: Free netdev resources under state lock
net: revert "net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit"
rtnetlink: fix the wrong minimal dump size getting from rtnl_calcit()
bnxt_en: Fix a VXLAN vs GENEVE issue
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- Fix a crash that occurs at driver initialization if the memory region
is already busy (request_mem_region() fails).
- Fix a vma validation check that mistakenly allows a private device-
dax mapping to be established. Device-dax explicitly forbids private
mappings so it can guarantee a given fault granularity and backing
memory type.
Both of these fixes have soaked in -next and are tagged for -stable.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fail all private mapping attempts
device-dax: check devm_nsio_enable() return value
|
|
Pull KVM fixes from Radim Krčmář:
"Four fixes for bugs found by syzkaller on x86, all for stable"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: check for pic and ioapic presence before use
KVM: x86: fix out-of-bounds accesses of rtc_eoi map
KVM: x86: drop error recovery in em_jmp_far and em_ret_far
KVM: x86: fix out-of-bounds access in lapic
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Set missing wakeup bit in LPCR on POWER9
- Fix the early OPAL console wrappers
- Fixup kernel read only mapping
Fixes for code merged this cycle:
- Fix missing CRCs, add more asm-prototypes.h declarations"
* tag 'powerpc-4.9-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fixup kernel read only mapping
powerpc/boot: Fix the early OPAL console wrappers
powerpc: Fix missing CRCs, add more asm-prototypes.h declarations
powerpc: Set missing wakeup bit in LPCR on POWER9
|
|
In commit 10724cc7bb78 ("tipc: redesign connection-level flow control")
we replaced the previous message based flow control with one based on
1k blocks. In order to ensure backwards compatibility the mechanism
falls back to using message as base unit when it senses that the peer
doesn't support the new algorithm. The default flow control window,
i.e., how many units can be sent before the sender blocks and waits
for an acknowledge (aka advertisement) is 512. This was tested against
the previous version, which uses an acknowledge frequency of on ack per
256 received message, and found to work fine.
However, we missed the fact that versions older than Linux 3.15 use an
acknowledge frequency of 512, which is exactly the limit where a 4.6+
sender will stop and wait for acknowledge. This would also work fine if
it weren't for the fact that if the first sent message on a 4.6+ server
side is an empty SYNACK, this one is also is counted as a sent message,
while it is not counted as a received message on a legacy 3.15-receiver.
This leads to the sender always being one step ahead of the receiver, a
scenario causing the sender to block after 512 sent messages, while the
receiver only has registered 511 read messages. Hence, the legacy
receiver is not trigged to send an acknowledge, with a permanently
blocked sender as result.
We solve this deadlock by simply allowing the sender to send one more
message before it blocks, i.e., by a making minimal change to the
condition used for determining connection congestion.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-7 detects a short memset in mvpp2, introduced in the original
merge of the driver:
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_cls_init':
drivers/net/ethernet/marvell/mvpp2.c:3296:2: error: 'memset' used with length equal to number of elements without multiplication by element size [-Werror=memset-elt-size]
The result seems to be that we write uninitialized data into the
flow table registers, although we did not get any warning about
that uninitialized data usage.
Using sizeof() lets us initialize then entire array instead.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
