Age | Commit message (Collapse) | Author |
|
One of the DMAs introduced with AM64 is the Block Copy DMA (BCDMA).
It serves similar purpose as K3 UDMAP channels in TR mode.
The rings for the BCDMA is integrated within the DMA itself instead of
using rings from the general purpose ringacc.
A BCDMA have two different type of channels:
- Block Copy Channels (bchan)
- Split Channels (tchan and rchan)
tchan and rchan can be used to service PSI-L peripherals, similarly to
K3 UDMA channels.
bchan can be only used for block copy operation (TR type15) like the
paired K3 UDMA tchan/rchan configured in block copy mode.
bchans can be also used to service peripherals directly if an external
trigger is selected for the channel.
Most of the driver code can be reused for BCDMA bchan/tchan/rchan support
but new setup and allocation functions are needed to handle the
differences between the DMAs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-18-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The DMAs in AM64 have built in rings compared to AM654/J721e/J7200 where a
separate and generic ringacc is used.
The ring SW interface is similar to ringacc with some major architectural
differences, like
They are part of the DMA (BCDMA or PKTDMA).
They are dual mode rings are modeled as pair of Rings objects which has
common configuration and memory buffer, but separate real-time control
register sets for each direction mem2dev (forward) and dev2mem (reverse).
The ringacc driver must be initialized for DMA rings use with
k3_ringacc_dmarings_init() as it is not an independent device as ringacc
is.
AM64 rings must be requested only using k3_ringacc_request_rings_pair(),
and forward ring must always be initialized/configured. After this any
other Ringacc APIs can be used without any callers changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-17-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In k3 architecture a DMA channel (in TR momde) can be triggered by global
events, origination from different modules.
The events for triggers can be sent from any module which is connected to
PSI-L fabric, but the event number to be sent is DMA channel specific, it
is only known after the channel itself is requested.
The router operation needs to be split up:
- route_allocate: configure the dma_spec for the DMA and store the
configuration which is needed for the router's input
- set_event: callback used by the DMA driver to set the event number for
the channel and enable the routing
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-16-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add initial PSI-L map file for AM64.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-15-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Additional fields needed for K3 PKTDMA to be able to handle the mapped
channels (channels are locked to handle specific threads) and flow ranges
for these mapped threads.
PKTDMA also introduces tflow for tx channels which can not be found in
K3 UDMA architecture.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-14-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
New binding document for
Texas Instruments K3 Packet DMA (PKTDMA).
PKTDMA is introduced as part of AM64.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201208090440.31792-13-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
New binding document for
Texas Instruments K3 Block Copy DMA (BCDMA).
BCDMA is introduced as part of AM64.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201208090440.31792-12-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
By using the dmaengine_get_dma_device() to get the device for
dma_api use, the dmatest can support per channel coherency if it is
supported by the DMA controller.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-11-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Client drivers should use the dmaengine_get_dma_device(chan) to get the
device pointer which should be used for DMA API for allocations and
mapping.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-10-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If the DMA device supports per channel coherency configuration (a channel
can be configured to have coherent or not coherent view) then a single
device (the DMA controller's device) can not be used for dma_api for all
channels as channels can have different coherency.
Introduce custom_dma_mapping flag for the dma_chan and a new helper to get
the device pointer to be used for dma_api for the given channel.
Client drivers should be updated to be able to support per channel
coherency by:
- dma_map_single(chan->device->dev, ptr, size, DMA_TO_DEVICE);
+ struct device *dma_dev = dmaengine_get_dma_device(chan);
+
+ dma_map_single(dma_dev, ptr, size, DMA_TO_DEVICE);
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-9-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Additional configuration for the DMA event router might be needed for a
channel which can not be done during device_alloc_chan_resources callback
since the router information is not yet present for the drivers.
If there is a need for additional configuration for the channel if DMA
router is in use, then the driver can implement the device_router_config
callback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-8-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Rings in RING mode should be using the DMA device for DMA API as in this
mode the ringacc will not access the ring memory in any ways, but the DMA
is.
Fix up the ring configuration and set the dma_dev unconditionally and let
the ringacc driver to select the correct device to use for DMA API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-7-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If of_xudma_dev_get() returns with the valid udma_dev then the driver
already got the ringacc, there is no need to execute
of_k3_ringacc_get_by_phandle() for each channel via the glue layer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-6-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Glue layer users should use the device of the DMA for DMA mapping and
allocations as it is the DMA which accesses to descriptors and buffers,
not the clients
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-5-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Resource allocation via sysfw can use up to two ranges per resource subtype
to support more complex resource assignment, mainly for DMA channels.
Take the second range also into consideration when setting up the maps for
available resources.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-4-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Set the TDTYPE if it is supported on the platform (j721e) which will cause
UDMAP to wait for the remote peer to finish the teardown before returning
the teardown completed message.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-3-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
According to different sections of the TRM, the hchan_cnt of CAP3 includes
the number of uchan in UDMA, thus the start offset of the normal channels
are hchan_cnt.
Fixes: daf4ad0499aa4 ("dmaengine: ti: k3-udma: Query throughput level information from hardware")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-2-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
drivers: soc: TI SOC changes for 5.11
- ti_sci changes towards DMSS support
- Static warning fixes
- Kconfig update for Keystone ARM64 socs
- AM64X SOC family support
|
|
To avoid multiple entries in MDMA interrupt handler for each flag&interrupt
enable, manage all flags set at once.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-5-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
DMA_SxPAR or DMA_SxM0AR/M1AR registers have to be aligned on PSIZE or MSIZE
respectively. This means that bus width needs to be forced to 1 byte when
computed width is not aligned with address.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-4-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When dma_channel_release is called, it means that the channel won't be used
anymore with the configuration it had. To ensure a future client can safely
use the channel after it has been released, clean the configuration done
when channel was requested.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-3-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
To better understand error that can be detected by the DMA controller,
manage the error flags before the transfer flags.
This way, it is possible to know if the FIFO error flag is set for an
over/underrun condition or a FIFO level error.
When a FIFO over/underrun condition occurs, the data is not lost because
peripheral request is not acknowledged by the stream until the over/
underrun condition is cleared. If this acknowledge takes too much time,
the peripheral itself may detect an over/underrun condition of its internal
buffer and data might be lost.
That's why in case the FIFO error flag is set, we check if the channel is
disabled or not, and if a Transfer Complete flag is set, which means that
the channel is disabled because of the end of transfer.
Because channel is disabled by hardware either by a FIFO level error, or by
an end of transfer.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-2-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
While performing suspend/resume, we were getting below kernel crash.
[ 54.541672] [FTS][Info]gesture suspend...
[ 54.605256] [FTS][Error][GESTURE]Enter into gesture(suspend) failed!
[ 54.605256]
[ 58.345850] irq event 10: bogus return value fffffff3
......
[ 58.345966] [<ffff0000080830f0>] el1_irq+0xb0/0x124
[ 58.345971] [<ffff000008085360>] arch_cpu_idle+0x10/0x18
[ 58.345975] [<ffff0000081077f4>] do_idle+0x1ac/0x1e0
[ 58.345979] [<ffff0000081079c8>] cpu_startup_entry+0x20/0x28
[ 58.345983] [<ffff000008a80ed0>] rest_init+0xd0/0xdc
[ 58.345988] [<ffff0000091c0b48>] start_kernel+0x390/0x3a4
[ 58.345990] handlers:
[ 58.345994] [<ffff0000085120d0>] bam_dma_irq
The reason for the crash we found is, bam_dma_irq() was returning
negative value when the device resumes in some conditions.
In addition, the irq handler should have one of the below return values.
IRQ_NONE interrupt was not from this device or was not handled
IRQ_HANDLED interrupt was handled by this device
IRQ_WAKE_THREAD handler requests to wake the handler thread
Therefore, to resolve this crash, we have changed the return value to
IRQ_NONE.
Signed-off-by: Parth Y Shah <sparth1292@gmail.com>
Link: https://lore.kernel.org/r/1607322820-7450-1-git-send-email-sparth1292@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support to allow configuration of Intel Analytics Accelerator (IAX) in
addition to the Intel Data Streaming Accelerator (DSA). The IAX hardware
has the same configuration interface as DSA. The main difference
is the type of operations it performs. We can support the DSA and
IAX devices on the same driver with some tweaks.
IAX has a 64B completion record that needs to be 64B aligned, as opposed to
a 32B completion record that is 32B aligned for DSA. IAX also does not
support token management.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/160564555488.1834439.4261958859935360473.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add bindings to APDMA for MT8516 SoC. MT8516 is compatible with MT6577.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201209114736.70625-1-fparent@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Update the kerneldoc function headers to fix build warnings:
drivers/dma/qcom/qcom_adm.c:180: warning: Function parameter or member 'chan' not described in 'adm_free_chan'
drivers/dma/qcom/qcom_adm.c:190: warning: Function parameter or member 'burst' not described in 'adm_get_blksize'
drivers/dma/qcom/qcom_adm.c:466: warning: Function parameter or member 'chan' not described in 'adm_terminate_all'
drivers/dma/qcom/qcom_adm.c:466: warning: Excess function parameter 'achan' description in 'adm_terminate_all'
drivers/dma/qcom/qcom_adm.c:503: warning: Function parameter or member 'achan' not described in 'adm_start_dma'
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Link: https://lore.kernel.org/r/20201126184602.GA1008@earth.li
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
With the DSA spec 1.1 update, a knob to disable ATS for individually is
introduced. Add enabling code to allow a system admin to make the
configuration through sysfs.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/160530810593.1288392.2561048329116529566.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver can match only via the DT table so the main table should be
always used and the of_match_ptr does not have any sense (this also
allows ACPI matching via PRP0001, even though it is not relevant here).
The secondary match of_device_id tables (passed to of_match_node) should
be marked as maybe unused to fix compile testing (!CONFIG_OF on x86_64)
warnings:
drivers/dma/ti/dma-crossbar.c:125:34: warning:
‘ti_am335x_master_match’ defined but not used [-Wunused-const-variable=]
drivers/dma/ti/dma-crossbar.c:22:34: warning:
‘ti_dma_xbar_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-6-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver uses a second of_device_id table in the probe()
function by passing it to of_match_node(). This code will be a no-op
for compile testing (!CONFIG_OF on x86_64):
drivers/dma/stm32-dmamux.c:171:34: warning:
‘stm32_stm32dma_master_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-5-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/sf-pdma/sf-pdma.c:576:34: warning:
‘sf_pdma_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-4-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/mv_xor.c:1281:34: warning:
‘mv_xor_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-3-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c:984:34: warning:
‘dw_dma_of_id_table’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-2-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/dma-jz4780.c:1031:34: warning:
‘jz4780_dma_dt_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The mxs-dma driver is only used by DT platforms and the .id_table
is unused.
Get rid of it to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123193051.17285-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Return the corresponding error code when first_msi_entry() returns
NULL in mv_xor_v2_probe().
Fixes: 19a340b1a820430 ("dmaengine: mv_xor_v2: new driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://lore.kernel.org/r/20201124010813.1939095-1-chengzhihao1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201124143405.2764-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This controller provides DMAengine capabilities for a variety of peripheral
buses such as I2C, UART, and SPI. By using GPI dmaengine driver, bus
drivers can use a standardize interface that is protocol independent to
transfer data between memory and peripheral.
Link: https://lore.kernel.org/r/20201109085450.24843-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Some complex dmaengine controllers have capability to program the
peripheral device, so pass on the peripheral configuration as part of
dma_slave_config
Link: https://lore.kernel.org/r/20201109085450.24843-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add devicetree binding documentation for GPI DMA controller
implemented on Qualcomm SoCs
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201109085450.24843-2-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add the DMA engine driver for the QCOM Application Data Mover (ADM) DMA
controller found in the MSM8x60 and IPQ/APQ8064 platforms.
The ADM supports both memory to memory transactions and memory
to/from peripheral device transactions. The controller also provides
flow control capabilities for transactions to/from peripheral devices.
The initial release of this driver supports slave transfers to/from
peripherals and also incorporates CRCI (client rate control interface)
flow control.
The hardware only supports a 32 bit physical address, so specifying
!PHYS_ADDR_T_64BIT gives maximum COMPILE_TEST coverage without having to
spend effort on kludging things in the code that will never actually be
needed on real hardware.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Link: https://lore.kernel.org/r/20201114140233.GM32650@earth.li
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Fix to return the error code from of_get_child_by_name() instaed of 0
in knav_queue_probe().
Fixes: 41f93af900a20d1a0a ("soc: ti: add Keystone Navigator QMSS driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The patch fix two reference leak.
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to call put operation will result in
reference leak.
2) The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced.
We fix it by: 1) adding call pm_runtime_put_noidle or
pm_runtime_put_sync in error handling. 2) adding pm_runtime_disable
in error handling, to keep usage counter and disable depth balanced.
Fixes: 88139ed030583 ("soc: ti: add Keystone Navigator DMA support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Since the of_device_get_match_data() doesn't return error code, remove
wrong IS_ERR test. Proper check against NULL pointer is already done
later before usage: if (data && data->...).
Additionally, proceeding with empty device data is valid (e.g. in case
of "ti,am3356-pruss").
Reported-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
With the integration of chip-id detection scheme in kernel[1], there
is no specific need to maintain multitudes of SoC specific config
options, discussed as per [2], we have deprecated the usage in other
places for v5.10-rc1. Drop the configuration for the follow on kernel.
[1] drivers/soc/ti/k3-socinfo.c commit 907a2b7e2fc7 ("soc: ti: add k3 platforms chipid module driver")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/k3-ringacc.c:163: warning: Function parameter or member 'state' not described in 'k3_ring'
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/wkup_m3_ipc.c:227: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_set_mem_type'
drivers/soc/ti/wkup_m3_ipc.c:236: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_set_resume_address'
drivers/soc/ti/wkup_m3_ipc.c:248: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_request_pm_status'
drivers/soc/ti/wkup_m3_ipc.c:268: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_prepare_low_power'
drivers/soc/ti/wkup_m3_ipc.c:322: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_finish_low_power'
drivers/soc/ti/wkup_m3_ipc.c:369: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_set_rtc_only'
drivers/soc/ti/wkup_m3_ipc.c:369: warning: Excess function parameter 'wkup_m3_wakeup' description in 'wkup_m3_set_rtc_only'
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/pm33xx.c: In function ‘am33xx_do_sram_idle’:
drivers/soc/ti/pm33xx.c:138:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/knav_dma.c:507: warning: Function parameter or member 'channel' not described in 'knav_dma_close_channel'
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Sandeep Nair <sandeep_n@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/knav_qmss_queue.c:528: warning: Function parameter or member 'flags' not described in 'knav_queue_open'
drivers/soc/ti/knav_qmss_queue.c:528: warning: Function parameter or member 'id' not described in 'knav_queue_open'
drivers/soc/ti/knav_qmss_queue.c:528: warning: Function parameter or member 'name' not described in 'knav_queue_open'
drivers/soc/ti/knav_qmss_queue.c:551: warning: Excess function parameter 'qh' description in 'knav_queue_close'
drivers/soc/ti/knav_qmss_queue.c:551: warning: Function parameter or member 'qhandle' not described in 'knav_queue_close'
drivers/soc/ti/knav_qmss_queue.c:583: warning: Excess function parameter 'qh' description in 'knav_queue_device_control'
drivers/soc/ti/knav_qmss_queue.c:583: warning: Function parameter or member 'arg' not described in 'knav_queue_device_control'
drivers/soc/ti/knav_qmss_queue.c:583: warning: Function parameter or member 'cmd' not described in 'knav_queue_device_control'
drivers/soc/ti/knav_qmss_queue.c:583: warning: Function parameter or member 'qhandle' not described in 'knav_queue_device_control'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Excess function parameter 'data' description in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Excess function parameter 'qh' description in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'dma' not described in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'flags' not described in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'qhandle' not described in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'size' not described in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:655: warning: Excess function parameter 'qh' description in 'knav_queue_pop'
drivers/soc/ti/knav_qmss_queue.c:655: warning: Function parameter or member 'qhandle' not described in 'knav_queue_pop'
drivers/soc/ti/knav_qmss_queue.c:655: warning: Function parameter or member 'size' not described in 'knav_queue_pop'
drivers/soc/ti/knav_qmss_queue.c:759: warning: Function parameter or member 'name' not described in 'knav_pool_create'
drivers/soc/ti/knav_qmss_queue.c:759: warning: Function parameter or member 'num_desc' not described in 'knav_pool_create'
drivers/soc/ti/knav_qmss_queue.c:759: warning: Function parameter or member 'region_id' not described in 'knav_pool_create'
drivers/soc/ti/knav_qmss_queue.c:862: warning: Excess function parameter 'pool' description in 'knav_pool_destroy'
drivers/soc/ti/knav_qmss_queue.c:862: warning: Function parameter or member 'ph' not described in 'knav_pool_destroy'
drivers/soc/ti/knav_qmss_queue.c:892: warning: Excess function parameter 'pool' description in 'knav_pool_desc_get'
drivers/soc/ti/knav_qmss_queue.c:892: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_get'
drivers/soc/ti/knav_qmss_queue.c:911: warning: Excess function parameter 'pool' description in 'knav_pool_desc_put'
drivers/soc/ti/knav_qmss_queue.c:911: warning: Function parameter or member 'desc' not described in 'knav_pool_desc_put'
drivers/soc/ti/knav_qmss_queue.c:911: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_put'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Excess function parameter 'pool' description in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'desc' not described in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'dma' not described in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'dma_sz' not described in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'size' not described in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:956: warning: Excess function parameter 'pool' description in 'knav_pool_desc_unmap'
drivers/soc/ti/knav_qmss_queue.c:956: warning: Function parameter or member 'dma' not described in 'knav_pool_desc_unmap'
drivers/soc/ti/knav_qmss_queue.c:956: warning: Function parameter or member 'dma_sz' not described in 'knav_pool_desc_unmap'
drivers/soc/ti/knav_qmss_queue.c:956: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_unmap'
drivers/soc/ti/knav_qmss_queue.c:975: warning: Excess function parameter 'pool' description in 'knav_pool_count'
drivers/soc/ti/knav_qmss_queue.c:975: warning: Function parameter or member 'ph' not described in 'knav_pool_count'
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Sandeep Nair <sandeep_n@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/knav_qmss_queue.c: In function ‘knav_setup_queue_pools’:
drivers/soc/ti/knav_qmss_queue.c:1310:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Sandeep Nair <sandeep_n@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|