diff options
Diffstat (limited to 'drivers/parisc')
-rw-r--r-- | drivers/parisc/asp.c | 6 | ||||
-rw-r--r-- | drivers/parisc/ccio-dma.c | 142 | ||||
-rw-r--r-- | drivers/parisc/ccio-rm-dma.c | 2 | ||||
-rw-r--r-- | drivers/parisc/dino.c | 42 | ||||
-rw-r--r-- | drivers/parisc/eisa.c | 4 | ||||
-rw-r--r-- | drivers/parisc/gsc.c | 11 | ||||
-rw-r--r-- | drivers/parisc/hppb.c | 10 | ||||
-rw-r--r-- | drivers/parisc/iosapic.c | 2 | ||||
-rw-r--r-- | drivers/parisc/lasi.c | 4 | ||||
-rw-r--r-- | drivers/parisc/lba_pci.c | 14 | ||||
-rw-r--r-- | drivers/parisc/led.c | 225 | ||||
-rw-r--r-- | drivers/parisc/pdc_stable.c | 2 | ||||
-rw-r--r-- | drivers/parisc/sba_iommu.c | 164 | ||||
-rw-r--r-- | drivers/parisc/superio.c | 3 | ||||
-rw-r--r-- | drivers/parisc/wax.c | 2 |
15 files changed, 364 insertions, 269 deletions
diff --git a/drivers/parisc/asp.c b/drivers/parisc/asp.c index 388609967133..558420bc9f88 100644 --- a/drivers/parisc/asp.c +++ b/drivers/parisc/asp.c @@ -77,12 +77,12 @@ asp_init_chip(struct parisc_device *dev) struct gsc_irq gsc_irq; int ret; - asp.version = gsc_readb(dev->hpa + ASP_VER_OFFSET) & 0xf; + asp.version = gsc_readb(dev->hpa.start + ASP_VER_OFFSET) & 0xf; asp.name = (asp.version == 1) ? "Asp" : "Cutoff"; asp.hpa = ASP_INTERRUPT_ADDR; printk(KERN_INFO "%s version %d at 0x%lx found.\n", - asp.name, asp.version, dev->hpa); + asp.name, asp.version, dev->hpa.start); /* the IRQ ASP should use */ ret = -EBUSY; @@ -126,7 +126,7 @@ static struct parisc_device_id asp_tbl[] = { }; struct parisc_driver asp_driver = { - .name = "Asp", + .name = "asp", .id_table = asp_tbl, .probe = asp_init_chip, }; diff --git a/drivers/parisc/ccio-dma.c b/drivers/parisc/ccio-dma.c index a3bd91a61827..9e0229f7e25f 100644 --- a/drivers/parisc/ccio-dma.c +++ b/drivers/parisc/ccio-dma.c @@ -100,9 +100,9 @@ #define DBG_RUN_SG(x...) #endif -#define CCIO_INLINE /* inline */ -#define WRITE_U32(value, addr) gsc_writel(value, (u32 *)(addr)) -#define READ_U32(addr) gsc_readl((u32 *)(addr)) +#define CCIO_INLINE inline +#define WRITE_U32(value, addr) __raw_writel(value, addr) +#define READ_U32(addr) __raw_readl(addr) #define U2_IOA_RUNWAY 0x580 #define U2_BC_GSC 0x501 @@ -115,28 +115,28 @@ struct ioa_registers { /* Runway Supervisory Set */ - volatile int32_t unused1[12]; - volatile uint32_t io_command; /* Offset 12 */ - volatile uint32_t io_status; /* Offset 13 */ - volatile uint32_t io_control; /* Offset 14 */ - volatile int32_t unused2[1]; + int32_t unused1[12]; + uint32_t io_command; /* Offset 12 */ + uint32_t io_status; /* Offset 13 */ + uint32_t io_control; /* Offset 14 */ + int32_t unused2[1]; /* Runway Auxiliary Register Set */ - volatile uint32_t io_err_resp; /* Offset 0 */ - volatile uint32_t io_err_info; /* Offset 1 */ - volatile uint32_t io_err_req; /* Offset 2 */ - volatile uint32_t io_err_resp_hi; /* Offset 3 */ - volatile uint32_t io_tlb_entry_m; /* Offset 4 */ - volatile uint32_t io_tlb_entry_l; /* Offset 5 */ - volatile uint32_t unused3[1]; - volatile uint32_t io_pdir_base; /* Offset 7 */ - volatile uint32_t io_io_low_hv; /* Offset 8 */ - volatile uint32_t io_io_high_hv; /* Offset 9 */ - volatile uint32_t unused4[1]; - volatile uint32_t io_chain_id_mask; /* Offset 11 */ - volatile uint32_t unused5[2]; - volatile uint32_t io_io_low; /* Offset 14 */ - volatile uint32_t io_io_high; /* Offset 15 */ + uint32_t io_err_resp; /* Offset 0 */ + uint32_t io_err_info; /* Offset 1 */ + uint32_t io_err_req; /* Offset 2 */ + uint32_t io_err_resp_hi; /* Offset 3 */ + uint32_t io_tlb_entry_m; /* Offset 4 */ + uint32_t io_tlb_entry_l; /* Offset 5 */ + uint32_t unused3[1]; + uint32_t io_pdir_base; /* Offset 7 */ + uint32_t io_io_low_hv; /* Offset 8 */ + uint32_t io_io_high_hv; /* Offset 9 */ + uint32_t unused4[1]; + uint32_t io_chain_id_mask; /* Offset 11 */ + uint32_t unused5[2]; + uint32_t io_io_low; /* Offset 14 */ + uint32_t io_io_high; /* Offset 15 */ }; /* @@ -226,7 +226,7 @@ struct ioa_registers { */ struct ioc { - struct ioa_registers *ioc_hpa; /* I/O MMU base address */ + struct ioa_registers __iomem *ioc_regs; /* I/O MMU base address */ u8 *res_map; /* resource map, bit == pdir entry */ u64 *pdir_base; /* physical base address */ u32 pdir_size; /* bytes, function of IOV Space size */ @@ -595,7 +595,7 @@ ccio_io_pdir_entry(u64 *pdir_ptr, space_t sid, unsigned long vba, ** Grab virtual index [0:11] ** Deposit virt_idx bits into I/O PDIR word */ - asm volatile ("lci 0(%%sr1, %1), %0" : "=r" (ci) : "r" (vba)); + asm volatile ("lci %%r0(%%sr1, %1), %0" : "=r" (ci) : "r" (vba)); asm volatile ("extru %1,19,12,%0" : "+r" (ci) : "r" (ci)); asm volatile ("depw %1,15,12,%0" : "+r" (pa) : "r" (ci)); @@ -613,7 +613,7 @@ ccio_io_pdir_entry(u64 *pdir_ptr, space_t sid, unsigned long vba, ** the real mode coherence index generation of U2, the PDIR entry ** must be flushed to memory to retain coherence." */ - asm volatile("fdc 0(%0)" : : "r" (pdir_ptr)); + asm volatile("fdc %%r0(%0)" : : "r" (pdir_ptr)); asm volatile("sync"); } @@ -636,7 +636,7 @@ ccio_clear_io_tlb(struct ioc *ioc, dma_addr_t iovp, size_t byte_cnt) byte_cnt += chain_size; while(byte_cnt > chain_size) { - WRITE_U32(CMD_TLB_PURGE | iovp, &ioc->ioc_hpa->io_command); + WRITE_U32(CMD_TLB_PURGE | iovp, &ioc->ioc_regs->io_command); iovp += chain_size; byte_cnt -= chain_size; } @@ -684,7 +684,7 @@ ccio_mark_invalid(struct ioc *ioc, dma_addr_t iova, size_t byte_cnt) ** Hopefully someone figures out how to patch (NOP) the ** FDC/SYNC out at boot time. */ - asm volatile("fdc 0(%0)" : : "r" (pdir_ptr[7])); + asm volatile("fdc %%r0(%0)" : : "r" (pdir_ptr[7])); iovp += IOVP_SIZE; byte_cnt -= IOVP_SIZE; @@ -1251,7 +1251,7 @@ static struct parisc_device_id ccio_tbl[] = { static int ccio_probe(struct parisc_device *dev); static struct parisc_driver ccio_driver = { - .name = "U2:Uturn", + .name = "ccio", .id_table = ccio_tbl, .probe = ccio_probe, }; @@ -1314,14 +1314,13 @@ ccio_ioc_init(struct ioc *ioc) ioc->pdir_size = (iova_space_size / IOVP_SIZE) * sizeof(u64); - BUG_ON(ioc->pdir_size >= 4 * 1024 * 1024); /* max pdir size < 4MB */ + BUG_ON(ioc->pdir_size > 8 * 1024 * 1024); /* max pdir size <= 8MB */ /* Verify it's a power of two */ BUG_ON((1 << get_order(ioc->pdir_size)) != (ioc->pdir_size >> PAGE_SHIFT)); - DBG_INIT("%s() hpa 0x%lx mem %luMB IOV %dMB (%d bits)\n", - __FUNCTION__, - ioc->ioc_hpa, + DBG_INIT("%s() hpa 0x%p mem %luMB IOV %dMB (%d bits)\n", + __FUNCTION__, ioc->ioc_regs, (unsigned long) num_physpages >> (20 - PAGE_SHIFT), iova_space_size>>20, iov_order + PAGE_SHIFT); @@ -1329,13 +1328,12 @@ ccio_ioc_init(struct ioc *ioc) ioc->pdir_base = (u64 *)__get_free_pages(GFP_KERNEL, get_order(ioc->pdir_size)); if(NULL == ioc->pdir_base) { - panic("%s:%s() could not allocate I/O Page Table\n", __FILE__, - __FUNCTION__); + panic("%s() could not allocate I/O Page Table\n", __FUNCTION__); } memset(ioc->pdir_base, 0, ioc->pdir_size); BUG_ON((((unsigned long)ioc->pdir_base) & PAGE_MASK) != (unsigned long)ioc->pdir_base); - DBG_INIT(" base %p", ioc->pdir_base); + DBG_INIT(" base %p\n", ioc->pdir_base); /* resource map size dictated by pdir_size */ ioc->res_size = (ioc->pdir_size / sizeof(u64)) >> 3; @@ -1344,8 +1342,7 @@ ccio_ioc_init(struct ioc *ioc) ioc->res_map = (u8 *)__get_free_pages(GFP_KERNEL, get_order(ioc->res_size)); if(NULL == ioc->res_map) { - panic("%s:%s() could not allocate resource map\n", __FILE__, - __FUNCTION__); + panic("%s() could not allocate resource map\n", __FUNCTION__); } memset(ioc->res_map, 0, ioc->res_size); @@ -1366,44 +1363,58 @@ ccio_ioc_init(struct ioc *ioc) ** Initialize IOA hardware */ WRITE_U32(CCIO_CHAINID_MASK << ioc->chainid_shift, - &ioc->ioc_hpa->io_chain_id_mask); + &ioc->ioc_regs->io_chain_id_mask); WRITE_U32(virt_to_phys(ioc->pdir_base), - &ioc->ioc_hpa->io_pdir_base); + &ioc->ioc_regs->io_pdir_base); /* ** Go to "Virtual Mode" */ - WRITE_U32(IOA_NORMAL_MODE, &ioc->ioc_hpa->io_control); + WRITE_U32(IOA_NORMAL_MODE, &ioc->ioc_regs->io_control); /* ** Initialize all I/O TLB entries to 0 (Valid bit off). */ - WRITE_U32(0, &ioc->ioc_hpa->io_tlb_entry_m); - WRITE_U32(0, &ioc->ioc_hpa->io_tlb_entry_l); + WRITE_U32(0, &ioc->ioc_regs->io_tlb_entry_m); + WRITE_U32(0, &ioc->ioc_regs->io_tlb_entry_l); for(i = 1 << CCIO_CHAINID_SHIFT; i ; i--) { WRITE_U32((CMD_TLB_DIRECT_WRITE | (i << ioc->chainid_shift)), - &ioc->ioc_hpa->io_command); + &ioc->ioc_regs->io_command); } } static void -ccio_init_resource(struct resource *res, char *name, unsigned long ioaddr) +ccio_init_resource(struct resource *res, char *name, void __iomem *ioaddr) { int result; res->parent = NULL; res->flags = IORESOURCE_MEM; - res->start = (unsigned long)(signed) __raw_readl(ioaddr) << 16; - res->end = (unsigned long)(signed) (__raw_readl(ioaddr + 4) << 16) - 1; + /* + * bracing ((signed) ...) are required for 64bit kernel because + * we only want to sign extend the lower 16 bits of the register. + * The upper 16-bits of range registers are hardcoded to 0xffff. + */ + res->start = (unsigned long)((signed) READ_U32(ioaddr) << 16); + res->end = (unsigned long)((signed) (READ_U32(ioaddr + 4) << 16) - 1); res->name = name; + /* + * Check if this MMIO range is disable + */ if (res->end + 1 == res->start) return; - result = request_resource(&iomem_resource, res); + + /* On some platforms (e.g. K-Class), we have already registered + * resources for devices reported by firmware. Some are children + * of ccio. + * "insert" ccio ranges in the mmio hierarchy (/proc/iomem). + */ + result = insert_resource(&iomem_resource, res); if (result < 0) { - printk(KERN_ERR "%s: failed to claim CCIO bus address space (%08lx,%08lx)\n", - __FILE__, res->start, res->end); + printk(KERN_ERR "%s() failed to claim CCIO bus address space (%08lx,%08lx)\n", + __FUNCTION__, res->start, res->end); } } @@ -1414,9 +1425,8 @@ static void __init ccio_init_resources(struct ioc *ioc) sprintf(name, "GSC Bus [%d/]", ioc->hw_path); - ccio_init_resource(res, name, (unsigned long)&ioc->ioc_hpa->io_io_low); - ccio_init_resource(res + 1, name, - (unsigned long)&ioc->ioc_hpa->io_io_low_hv); + ccio_init_resource(res, name, &ioc->ioc_regs->io_io_low); + ccio_init_resource(res + 1, name, &ioc->ioc_regs->io_io_low_hv); } static int new_ioc_area(struct resource *res, unsigned long size, @@ -1427,7 +1437,12 @@ static int new_ioc_area(struct resource *res, unsigned long size, res->start = (max - size + 1) &~ (align - 1); res->end = res->start + size; - if (!request_resource(&iomem_resource, res)) + + /* We might be trying to expand the MMIO range to include + * a child device that has already registered it's MMIO space. + * Use "insert" instead of request_resource(). + */ + if (!insert_resource(&iomem_resource, res)) return 0; return new_ioc_area(res, size, min, max - size, align); @@ -1486,15 +1501,15 @@ int ccio_allocate_resource(const struct parisc_device *dev, if (!expand_ioc_area(parent, size, min, max, align)) { __raw_writel(((parent->start)>>16) | 0xffff0000, - (unsigned long)&(ioc->ioc_hpa->io_io_low)); + &ioc->ioc_regs->io_io_low); __raw_writel(((parent->end)>>16) | 0xffff0000, - (unsigned long)&(ioc->ioc_hpa->io_io_high)); + &ioc->ioc_regs->io_io_high); } else if (!expand_ioc_area(parent + 1, size, min, max, align)) { parent++; __raw_writel(((parent->start)>>16) | 0xffff0000, - (unsigned long)&(ioc->ioc_hpa->io_io_low_hv)); + &ioc->ioc_regs->io_io_low_hv); __raw_writel(((parent->end)>>16) | 0xffff0000, - (unsigned long)&(ioc->ioc_hpa->io_io_high_hv)); + &ioc->ioc_regs->io_io_high_hv); } else { return -EBUSY; } @@ -1521,7 +1536,12 @@ int ccio_request_resource(const struct parisc_device *dev, return -EBUSY; } - return request_resource(parent, res); + /* "transparent" bus bridges need to register MMIO resources + * firmware assigned them. e.g. children of hppb.c (e.g. K-class) + * registered their resources in the PDC "bus walk" (See + * arch/parisc/kernel/inventory.c). + */ + return insert_resource(parent, res); } /** @@ -1546,7 +1566,7 @@ static int ccio_probe(struct parisc_device *dev) ioc->name = dev->id.hversion == U2_IOA_RUNWAY ? "U2" : "UTurn"; - printk(KERN_INFO "Found %s at 0x%lx\n", ioc->name, dev->hpa); + printk(KERN_INFO "Found %s at 0x%lx\n", ioc->name, dev->hpa.start); for (i = 0; i < ioc_count; i++) { ioc_p = &(*ioc_p)->next; @@ -1554,7 +1574,7 @@ static int ccio_probe(struct parisc_device *dev) *ioc_p = ioc; ioc->hw_path = dev->hw_path; - ioc->ioc_hpa = (struct ioa_registers *)dev->hpa; + ioc->ioc_regs = ioremap(dev->hpa.start, 4096); ccio_ioc_init(ioc); ccio_init_resources(ioc); hppa_dma_ops = &ccio_ops; diff --git a/drivers/parisc/ccio-rm-dma.c b/drivers/parisc/ccio-rm-dma.c index 57e6385976e2..356b8357bccc 100644 --- a/drivers/parisc/ccio-rm-dma.c +++ b/drivers/parisc/ccio-rm-dma.c @@ -167,7 +167,7 @@ ccio_probe(struct parisc_device *dev) { printk(KERN_INFO "%s found %s at 0x%lx\n", MODULE_NAME, dev->id.hversion == U2_BC_GSC ? "U2" : "UTurn", - dev->hpa); + dev->hpa.start); /* ** FIXME - should check U2 registers to verify it's really running diff --git a/drivers/parisc/dino.c b/drivers/parisc/dino.c index 2f2dbef2c3b7..5ab75334c579 100644 --- a/drivers/parisc/dino.c +++ b/drivers/parisc/dino.c @@ -178,6 +178,8 @@ static int dino_cfg_read(struct pci_bus *bus, unsigned int devfn, int where, void __iomem *base_addr = d->hba.base_addr; unsigned long flags; + DBG("%s: %p, %d, %d, %d\n", __FUNCTION__, base_addr, devfn, where, + size); spin_lock_irqsave(&d->dinosaur_pen, flags); /* tell HW which CFG address */ @@ -211,6 +213,8 @@ static int dino_cfg_write(struct pci_bus *bus, unsigned int devfn, int where, void __iomem *base_addr = d->hba.base_addr; unsigned long flags; + DBG("%s: %p, %d, %d, %d\n", __FUNCTION__, base_addr, devfn, where, + size); spin_lock_irqsave(&d->dinosaur_pen, flags); /* avoid address stepping feature */ @@ -295,7 +299,7 @@ static void dino_disable_irq(unsigned int irq) struct dino_device *dino_dev = irq_desc[irq].handler_data; int local_irq = gsc_find_local_irq(irq, dino_dev->global_irq, irq); - DBG(KERN_WARNING "%s(0x%p, %d)\n", __FUNCTION__, irq_dev, irq); + DBG(KERN_WARNING "%s(0x%p, %d)\n", __FUNCTION__, dino_dev, irq); /* Clear the matching bit in the IMR register */ dino_dev->imr &= ~(DINO_MASK_IRQ(local_irq)); @@ -308,7 +312,7 @@ static void dino_enable_irq(unsigned int irq) int local_irq = gsc_find_local_irq(irq, dino_dev->global_irq, irq); u32 tmp; - DBG(KERN_WARNING "%s(0x%p, %d)\n", __FUNCTION__, irq_dev, irq); + DBG(KERN_WARNING "%s(0x%p, %d)\n", __FUNCTION__, dino_dev, irq); /* ** clear pending IRQ bits @@ -490,7 +494,7 @@ dino_card_setup(struct pci_bus *bus, void __iomem *base_addr) if (res->start == F_EXTEND(0xf0000000UL | (i * _8MB))) break; } - DBG("DINO GSC WRITE i=%d, start=%lx, dino addr = %lx\n", + DBG("DINO GSC WRITE i=%d, start=%lx, dino addr = %p\n", i, res->start, base_addr + DINO_IO_ADDR_EN); __raw_writel(1 << i, base_addr + DINO_IO_ADDR_EN); } @@ -683,6 +687,14 @@ static void __init dino_card_init(struct dino_device *dino_dev) { u32 brdg_feat = 0x00784e05; + unsigned long status; + + status = __raw_readl(dino_dev->hba.base_addr+DINO_IO_STATUS); + if (status & 0x0000ff80) { + __raw_writel(0x00000005, + dino_dev->hba.base_addr+DINO_IO_COMMAND); + udelay(1); + } __raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_GMASK); __raw_writel(0x00000001, dino_dev->hba.base_addr+DINO_IO_FBB_EN); @@ -902,15 +914,15 @@ void ccio_cujo20_fixup(struct parisc_device *dev, u32 iovp); ** If so, initialize the chip appropriately (card-mode vs bridge mode). ** Much of the initialization is common though. */ -static int __init -dino_driver_callback(struct parisc_device *dev) +static int __init dino_probe(struct parisc_device *dev) { struct dino_device *dino_dev; // Dino specific control struct const char *version = "unknown"; char *name; int is_cujo = 0; struct pci_bus *bus; - + unsigned long hpa = dev->hpa.start; + name = "Dino"; if (is_card_dino(&dev->id)) { version = "3.x (card mode)"; @@ -928,11 +940,11 @@ dino_driver_callback(struct parisc_device *dev) } } - printk("%s version %s found at 0x%lx\n", name, version, dev->hpa); + printk("%s version %s found at 0x%lx\n", name, version, hpa); - if (!request_mem_region(dev->hpa, PAGE_SIZE, name)) { + if (!request_mem_region(hpa, PAGE_SIZE, name)) { printk(KERN_ERR "DINO: Hey! Someone took my MMIO space (0x%ld)!\n", - dev->hpa); + hpa); return 1; } @@ -940,12 +952,12 @@ dino_driver_callback(struct parisc_device *dev) if (is_cujo && dev->id.hversion_rev == 1) { #ifdef CONFIG_IOMMU_CCIO printk(KERN_WARNING "Enabling Cujo 2.0 bug workaround\n"); - if (dev->hpa == (unsigned long)CUJO_RAVEN_ADDR) { + if (hpa == (unsigned long)CUJO_RAVEN_ADDR) { ccio_cujo20_fixup(dev, CUJO_RAVEN_BADPAGE); - } else if (dev->hpa == (unsigned long)CUJO_FIREHAWK_ADDR) { + } else if (hpa == (unsigned long)CUJO_FIREHAWK_ADDR) { ccio_cujo20_fixup(dev, CUJO_FIREHAWK_BADPAGE); } else { - printk("Don't recognise Cujo at address 0x%lx, not enabling workaround\n", dev->hpa); + printk("Don't recognise Cujo at address 0x%lx, not enabling workaround\n", hpa); } #endif } else if (!is_cujo && !is_card_dino(&dev->id) && @@ -970,7 +982,7 @@ dino_driver_callback(struct parisc_device *dev) memset(dino_dev, 0, sizeof(struct dino_device)); dino_dev->hba.dev = dev; - dino_dev->hba.base_addr = ioremap(dev->hpa, 4096); /* faster access */ + dino_dev->hba.base_addr = ioremap(hpa, 4096); dino_dev->hba.lmmio_space_offset = 0; /* CPU addrs == bus addrs */ spin_lock_init(&dino_dev->dinosaur_pen); dino_dev->hba.iommu = ccio_get_iommu(dev); @@ -1027,9 +1039,9 @@ static struct parisc_device_id dino_tbl[] = { }; static struct parisc_driver dino_driver = { - .name = "Dino", + .name = "dino", .id_table = dino_tbl, - .probe = dino_driver_callback, + .probe = dino_probe, }; /* diff --git a/drivers/parisc/eisa.c b/drivers/parisc/eisa.c index 043d47aea75b..6362bf99eff6 100644 --- a/drivers/parisc/eisa.c +++ b/drivers/parisc/eisa.c @@ -315,7 +315,7 @@ static int __devinit eisa_probe(struct parisc_device *dev) char *name = is_mongoose(dev) ? "Mongoose" : "Wax"; printk(KERN_INFO "%s EISA Adapter found at 0x%08lx\n", - name, dev->hpa); + name, dev->hpa.start); eisa_dev.hba.dev = dev; eisa_dev.hba.iommu = ccio_get_iommu(dev); @@ -397,7 +397,7 @@ static struct parisc_device_id eisa_tbl[] = { MODULE_DEVICE_TABLE(parisc, eisa_tbl); static struct parisc_driver eisa_driver = { - .name = "EISA Bus Adapter", + .name = "eisa_ba", .id_table = eisa_tbl, .probe = eisa_probe, }; diff --git a/drivers/parisc/gsc.c b/drivers/parisc/gsc.c index af5e02526a18..16d40f95978d 100644 --- a/drivers/parisc/gsc.c +++ b/drivers/parisc/gsc.c @@ -183,12 +183,20 @@ void gsc_asic_assign_irq(struct gsc_asic *asic, int local_irq, int *irqp) *irqp = irq; } +static struct device *next_device(struct klist_iter *i) +{ + struct klist_node * n = klist_next(i); + return n ? container_of(n, struct device, knode_parent) : NULL; +} + void gsc_fixup_irqs(struct parisc_device *parent, void *ctrl, void (*choose_irq)(struct parisc_device *, void *)) { struct device *dev; + struct klist_iter i; - list_for_each_entry(dev, &parent->dev.children, node) { + klist_iter_init(&parent->dev.klist_children, &i); + while ((dev = next_device(&i))) { struct parisc_device *padev = to_parisc_device(dev); /* work-around for 715/64 and others which have parent @@ -197,6 +205,7 @@ void gsc_fixup_irqs(struct parisc_device *parent, void *ctrl, return gsc_fixup_irqs(padev, ctrl, choose_irq); choose_irq(padev, ctrl); } + klist_iter_exit(&i); } int gsc_common_setup(struct parisc_device *parent, struct gsc_asic *gsc_asic) diff --git a/drivers/parisc/hppb.c b/drivers/parisc/hppb.c index e869c6020370..5edf93f80757 100644 --- a/drivers/parisc/hppb.c +++ b/drivers/parisc/hppb.c @@ -68,14 +68,14 @@ static int hppb_probe(struct parisc_device *dev) memset(card->next, '\0', sizeof(struct hppb_card)); card = card->next; } - printk(KERN_INFO "Found GeckoBoa at 0x%lx\n", dev->hpa); + printk(KERN_INFO "Found GeckoBoa at 0x%lx\n", dev->hpa.start); - card->hpa = dev->hpa; + card->hpa = dev->hpa.start; card->mmio_region.name = "HP-PB Bus"; card->mmio_region.flags = IORESOURCE_MEM; - card->mmio_region.start = __raw_readl(dev->hpa + IO_IO_LOW); - card->mmio_region.end = __raw_readl(dev->hpa + IO_IO_HIGH) - 1; + card->mmio_region.start = gsc_readl(dev->hpa.start + IO_IO_LOW); + card->mmio_region.end = gsc_readl(dev->hpa.start + IO_IO_HIGH) - 1; status = ccio_request_resource(dev, &card->mmio_region); if(status < 0) { @@ -93,7 +93,7 @@ static struct parisc_device_id hppb_tbl[] = { }; static struct parisc_driver hppb_driver = { - .name = "Gecko Boa", + .name = "gecko_boa", .id_table = hppb_tbl, .probe = hppb_probe, }; diff --git a/drivers/parisc/iosapic.c b/drivers/parisc/iosapic.c index 7a57c1b8373f..a39fbfef789a 100644 --- a/drivers/parisc/iosapic.c +++ b/drivers/parisc/iosapic.c @@ -244,7 +244,7 @@ static struct irt_entry *iosapic_alloc_irt(int num_entries) * 4-byte alignment on 32-bit kernels */ a = (unsigned long)kmalloc(sizeof(struct irt_entry) * num_entries + 8, GFP_KERNEL); - a = (a + 7) & ~7; + a = (a + 7UL) & ~7UL; return (struct irt_entry *)a; } diff --git a/drivers/parisc/lasi.c b/drivers/parisc/lasi.c index cb84a4e84a2f..a8c20396ffbe 100644 --- a/drivers/parisc/lasi.c +++ b/drivers/parisc/lasi.c @@ -175,7 +175,7 @@ lasi_init_chip(struct parisc_device *dev) return -ENOMEM; lasi->name = "Lasi"; - lasi->hpa = dev->hpa; + lasi->hpa = dev->hpa.start; /* Check the 4-bit (yes, only 4) version register */ lasi->version = gsc_readl(lasi->hpa + LASI_VER) & 0xf; @@ -233,7 +233,7 @@ static struct parisc_device_id lasi_tbl[] = { }; struct parisc_driver lasi_driver = { - .name = "Lasi", + .name = "lasi", .id_table = lasi_tbl, .probe = lasi_init_chip, }; diff --git a/drivers/parisc/lba_pci.c b/drivers/parisc/lba_pci.c index 7fdd80b7eb47..5e495dcbc58a 100644 --- a/drivers/parisc/lba_pci.c +++ b/drivers/parisc/lba_pci.c @@ -1288,7 +1288,7 @@ lba_legacy_resources(struct parisc_device *pa_dev, struct lba_device *lba_dev) ** Adjust "window" for this rope. */ rsize /= ROPES_PER_IOC; - r->start += (rsize + 1) * LBA_NUM(pa_dev->hpa); + r->start += (rsize + 1) * LBA_NUM(pa_dev->hpa.start); r->end = r->start + rsize; } else { r->end = r->start = 0; /* Not enabled. */ @@ -1458,7 +1458,7 @@ lba_driver_probe(struct parisc_device *dev) u32 func_class; void *tmp_obj; char *version; - void __iomem *addr = ioremap(dev->hpa, 4096); + void __iomem *addr = ioremap(dev->hpa.start, 4096); /* Read HW Rev First */ func_class = READ_REG32(addr + LBA_FCLASS); @@ -1476,7 +1476,7 @@ lba_driver_probe(struct parisc_device *dev) } printk(KERN_INFO "%s version %s (0x%x) found at 0x%lx\n", - MODULE_NAME, version, func_class & 0xf, dev->hpa); + MODULE_NAME, version, func_class & 0xf, dev->hpa.start); if (func_class < 2) { printk(KERN_WARNING "Can't support LBA older than " @@ -1503,17 +1503,17 @@ lba_driver_probe(struct parisc_device *dev) * but for the mask for func_class. */ printk(KERN_INFO "%s version %s (0x%x) found at 0x%lx\n", - MODULE_NAME, version, func_class & 0xff, dev->hpa); + MODULE_NAME, version, func_class & 0xff, dev->hpa.start); cfg_ops = &mercury_cfg_ops; } else { - printk(KERN_ERR "Unknown LBA found at 0x%lx\n", dev->hpa); + printk(KERN_ERR "Unknown LBA found at 0x%lx\n", dev->hpa.start); return -ENODEV; } /* ** Tell I/O SAPIC driver we have a IRQ handler/region. */ - tmp_obj = iosapic_register(dev->hpa + LBA_IOSAPIC_BASE); + tmp_obj = iosapic_register(dev->hpa.start + LBA_IOSAPIC_BASE); /* NOTE: PCI devices (e.g. 103c:1005 graphics card) which don't ** have an IRT entry will get NULL back from iosapic code. @@ -1635,7 +1635,7 @@ void __init lba_init(void) */ void lba_set_iregs(struct parisc_device *lba, u32 ibase, u32 imask) { - void __iomem * base_addr = ioremap(lba->hpa, 4096); + void __iomem * base_addr = ioremap(lba->hpa.start, 4096); imask <<= 2; /* adjust for hints - 2 more bits */ diff --git a/drivers/parisc/led.c b/drivers/parisc/led.c index 286902298e33..95bd07b8b61b 100644 --- a/drivers/parisc/led.c +++ b/drivers/parisc/led.c @@ -18,6 +18,9 @@ * Changes: * - Audit copy_from_user in led_proc_write. * Daniele Bellucci <bellucda@tiscali.it> + * - Switch from using a tasklet to a work queue, so the led_LCD_driver + * can sleep. + * David Pye <dmp@davidmpye.dyndns.org> */ #include <linux/config.h> @@ -37,6 +40,7 @@ #include <linux/proc_fs.h> #include <linux/ctype.h> #include <linux/blkdev.h> +#include <linux/workqueue.h> #include <linux/rcupdate.h> #include <asm/io.h> #include <asm/processor.h> @@ -47,25 +51,30 @@ #include <asm/uaccess.h> /* The control of the LEDs and LCDs on PARISC-machines have to be done - completely in software. The necessary calculations are done in a tasklet - which is scheduled at every timer interrupt and since the calculations - may consume relatively much CPU-time some of the calculations can be + completely in software. The necessary calculations are done in a work queue + task which is scheduled regularly, and since the calculations may consume a + relatively large amount of CPU time, some of the calculations can be turned off with the following variables (controlled via procfs) */ static int led_type = -1; -static int led_heartbeat = 1; -static int led_diskio = 1; -static int led_lanrxtx = 1; +static unsigned char lastleds; /* LED state from most recent update */ +static unsigned int led_heartbeat = 1; +static unsigned int led_diskio = 1; +static unsigned int led_lanrxtx = 1; static char lcd_text[32]; static char lcd_text_default[32]; + +static struct workqueue_struct *led_wq; +static void led_work_func(void *); +static DECLARE_WORK(led_task, led_work_func, NULL); + #if 0 #define DPRINTK(x) printk x #else #define DPRINTK(x) #endif - struct lcd_block { unsigned char command; /* stores the command byte */ unsigned char on; /* value for turning LED on */ @@ -116,12 +125,27 @@ lcd_info __attribute__((aligned(8))) = #define LCD_DATA_REG lcd_info.lcd_data_reg_addr #define LED_DATA_REG lcd_info.lcd_cmd_reg_addr /* LASI & ASP only */ +#define LED_HASLCD 1 +#define LED_NOLCD 0 + +/* The workqueue must be created at init-time */ +static int start_task(void) +{ + /* Display the default text now */ + if (led_type == LED_HASLCD) lcd_print( lcd_text_default ); + + /* Create the work queue and queue the LED task */ + led_wq = create_singlethread_workqueue("led_wq"); + queue_work(led_wq, &led_task); + + return 0; +} + +device_initcall(start_task); /* ptr to LCD/LED-specific function */ static void (*led_func_ptr) (unsigned char); -#define LED_HASLCD 1 -#define LED_NOLCD 0 #ifdef CONFIG_PROC_FS static int led_proc_read(char *page, char **start, off_t off, int count, int *eof, void *data) @@ -286,52 +310,35 @@ static void led_LASI_driver(unsigned char leds) /* ** ** led_LCD_driver() - ** - ** The logic of the LCD driver is, that we write at every scheduled call - ** only to one of LCD_CMD_REG _or_ LCD_DATA_REG - registers. - ** That way we don't need to let this tasklet busywait for min_cmd_delay - ** milliseconds. - ** - ** TODO: check the value of "min_cmd_delay" against the value of HZ. ** */ static void led_LCD_driver(unsigned char leds) { - static int last_index; /* 0:heartbeat, 1:disk, 2:lan_in, 3:lan_out */ - static int last_was_cmd;/* 0: CMD was written last, 1: DATA was last */ - struct lcd_block *block_ptr; - int value; - - switch (last_index) { - case 0: block_ptr = &lcd_info.heartbeat; - value = leds & LED_HEARTBEAT; - break; - case 1: block_ptr = &lcd_info.disk_io; - value = leds & LED_DISK_IO; - break; - case 2: block_ptr = &lcd_info.lan_rcv; - value = leds & LED_LAN_RCV; - break; - case 3: block_ptr = &lcd_info.lan_tx; - value = leds & LED_LAN_TX; - break; - default: /* should never happen: */ - return; - } - - if (last_was_cmd) { - /* write the value to the LCD data port */ - gsc_writeb( value ? block_ptr->on : block_ptr->off, LCD_DATA_REG ); - } else { - /* write the command-byte to the LCD command register */ - gsc_writeb( block_ptr->command, LCD_CMD_REG ); - } + static int i; + static unsigned char mask[4] = { LED_HEARTBEAT, LED_DISK_IO, + LED_LAN_RCV, LED_LAN_TX }; - /* now update the vars for the next interrupt iteration */ - if (++last_was_cmd == 2) { /* switch between cmd & data */ - last_was_cmd = 0; - if (++last_index == 4) - last_index = 0; /* switch back to heartbeat index */ + static struct lcd_block * blockp[4] = { + &lcd_info.heartbeat, + &lcd_info.disk_io, + &lcd_info.lan_rcv, + &lcd_info.lan_tx + }; + + /* Convert min_cmd_delay to milliseconds */ + unsigned int msec_cmd_delay = 1 + (lcd_info.min_cmd_delay / 1000); + + for (i=0; i<4; ++i) + { + if ((leds & mask[i]) != (lastleds & mask[i])) + { + gsc_writeb( blockp[i]->command, LCD_CMD_REG ); + msleep(msec_cmd_delay); + + gsc_writeb( leds & mask[i] ? blockp[i]->on : + blockp[i]->off, LCD_DATA_REG ); + msleep(msec_cmd_delay); + } } } @@ -356,7 +363,7 @@ static __inline__ int led_get_net_activity(void) rx_total = tx_total = 0; - /* we are running as tasklet, so locking dev_base + /* we are running as a workqueue task, so locking dev_base * for reading should be OK */ read_lock(&dev_base_lock); rcu_read_lock(); @@ -405,7 +412,7 @@ static __inline__ int led_get_diskio_activity(void) static unsigned long last_pgpgin, last_pgpgout; struct page_state pgstat; int changed; - + get_full_page_state(&pgstat); /* get no of sectors in & out */ /* Just use a very simple calculation here. Do not care about overflow, @@ -413,86 +420,70 @@ static __inline__ int led_get_diskio_activity(void) changed = (pgstat.pgpgin != last_pgpgin) || (pgstat.pgpgout != last_pgpgout); last_pgpgin = pgstat.pgpgin; last_pgpgout = pgstat.pgpgout; - + return (changed ? LED_DISK_IO : 0); } /* - ** led_tasklet_func() + ** led_work_func() ** - ** is scheduled at every timer interrupt from time.c and - ** updates the chassis LCD/LED + ** manages when and which chassis LCD/LED gets updated TODO: - display load average (older machines like 715/64 have 4 "free" LED's for that) - optimizations */ -#define HEARTBEAT_LEN (HZ*6/100) -#define HEARTBEAT_2ND_RANGE_START (HZ*22/100) +#define HEARTBEAT_LEN (HZ*10/100) +#define HEARTBEAT_2ND_RANG |