summaryrefslogtreecommitdiffstats
path: root/arch/i386/kernel/apic.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/i386/kernel/apic.c')
-rw-r--r--arch/i386/kernel/apic.c365
1 files changed, 215 insertions, 150 deletions
diff --git a/arch/i386/kernel/apic.c b/arch/i386/kernel/apic.c
index e98b5c750bdf..9655c233e6f1 100644
--- a/arch/i386/kernel/apic.c
+++ b/arch/i386/kernel/apic.c
@@ -26,6 +26,7 @@
#include <linux/sysdev.h>
#include <linux/cpu.h>
#include <linux/clockchips.h>
+#include <linux/acpi_pmtmr.h>
#include <linux/module.h>
#include <asm/atomic.h>
@@ -59,8 +60,8 @@
*/
static int enable_local_apic __initdata = 0;
-/* Enable local APIC timer for highres/dyntick on UP */
-static int enable_local_apic_timer __initdata = 0;
+/* Local APIC timer verification ok */
+static int local_apic_timer_verify_ok;
/*
* Debug level, exported for io_apic.c
@@ -82,7 +83,7 @@ static void apic_pm_activate(void);
static struct clock_event_device lapic_clockevent = {
.name = "lapic",
.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT
- | CLOCK_EVT_FEAT_C3STOP,
+ | CLOCK_EVT_FEAT_C3STOP | CLOCK_EVT_FEAT_DUMMY,
.shift = 32,
.set_mode = lapic_timer_setup,
.set_next_event = lapic_next_event,
@@ -159,64 +160,8 @@ int lapic_get_maxlvt(void)
* Local APIC timer
*/
-/*
- * This part sets up the APIC 32 bit clock in LVTT1, with HZ interrupts
- * per second. We assume that the caller has already set up the local
- * APIC.
- *
- * The APIC timer is not exactly sync with the external timer chip, it
- * closely follows bus clocks.
- */
-
-/*
- * FIXME: Move this to i8253.h. There is no need to keep the access to
- * the PIT scattered all around the place -tglx
- */
-
-/*
- * The timer chip is already set up at HZ interrupts per second here,
- * but we do not accept timer interrupts yet. We only allow the BP
- * to calibrate.
- */
-static unsigned int __devinit get_8254_timer_count(void)
-{
- unsigned long flags;
-
- unsigned int count;
-
- spin_lock_irqsave(&i8253_lock, flags);
-
- outb_p(0x00, PIT_MODE);
- count = inb_p(PIT_CH0);
- count |= inb_p(PIT_CH0) << 8;
-
- spin_unlock_irqrestore(&i8253_lock, flags);
-
- return count;
-}
-
-/* next tick in 8254 can be caught by catching timer wraparound */
-static void __devinit wait_8254_wraparound(void)
-{
- unsigned int curr_count, prev_count;
-
- curr_count = get_8254_timer_count();
- do {
- prev_count = curr_count;
- curr_count = get_8254_timer_count();
-
- /* workaround for broken Mercury/Neptune */
- if (prev_count >= curr_count + 0x100)
- curr_count = get_8254_timer_count();
-
- } while (prev_count >= curr_count);
-}
-
-/*
- * Default initialization for 8254 timers. If we use other timers like HPET,
- * we override this later
- */
-void (*wait_timer_tick)(void) __devinitdata = wait_8254_wraparound;
+/* Clock divisor is set to 16 */
+#define APIC_DIVISOR 16
/*
* This function sets up the local APIC timer, with a timeout of
@@ -228,9 +173,6 @@ void (*wait_timer_tick)(void) __devinitdata = wait_8254_wraparound;
* We do reads before writes even if unnecessary, to get around the
* P5 APIC double write bug.
*/
-
-#define APIC_DIVISOR 16
-
static void __setup_APIC_LVTT(unsigned int clocks, int oneshot, int irqen)
{
unsigned int lvtt_value, tmp_value;
@@ -277,6 +219,10 @@ static void lapic_timer_setup(enum clock_event_mode mode,
unsigned long flags;
unsigned int v;
+ /* Lapic used for broadcast ? */
+ if (!local_apic_timer_verify_ok)
+ return;
+
local_irq_save(flags);
switch (mode) {
@@ -321,111 +267,238 @@ static void __devinit setup_APIC_timer(void)
}
/*
- * In this function we calibrate APIC bus clocks to the external
- * timer. Unfortunately we cannot use jiffies and the timer irq
- * to calibrate, since some later bootup code depends on getting
- * the first irq? Ugh.
+ * In this functions we calibrate APIC bus clocks to the external timer.
+ *
+ * We want to do the calibration only once since we want to have local timer
+ * irqs syncron. CPUs connected by the same APIC bus have the very same bus
+ * frequency.
*
- * TODO: Fix this rather than saying "Ugh" -tglx
+ * This was previously done by reading the PIT/HPET and waiting for a wrap
+ * around to find out, that a tick has elapsed. I have a box, where the PIT
+ * readout is broken, so it never gets out of the wait loop again. This was
+ * also reported by others.
*
- * We want to do the calibration only once since we
- * want to have local timer irqs syncron. CPUs connected
- * by the same APIC bus have the very same bus frequency.
- * And we want to have irqs off anyways, no accidental
- * APIC irq that way.
+ * Monitoring the jiffies value is inaccurate and the clockevents
+ * infrastructure allows us to do a simple substitution of the interrupt
+ * handler.
+ *
+ * The calibration routine also uses the pm_timer when possible, as the PIT
+ * happens to run way too slow (factor 2.3 on my VAIO CoreDuo, which goes
+ * back to normal later in the boot process).
*/
-static int __init calibrate_APIC_clock(void)
+#define LAPIC_CAL_LOOPS (HZ/10)
+
+static __initdata volatile int lapic_cal_loops = -1;
+static __initdata long lapic_cal_t1, lapic_cal_t2;
+static __initdata unsigned long long lapic_cal_tsc1, lapic_cal_tsc2;
+static __initdata unsigned long lapic_cal_pm1, lapic_cal_pm2;
+static __initdata unsigned long lapic_cal_j1, lapic_cal_j2;
+
+/*
+ * Temporary interrupt handler.
+ */
+static void __init lapic_cal_handler(struct clock_event_device *dev)
+{
+ unsigned long long tsc = 0;
+ long tapic = apic_read(APIC_TMCCT);
+ unsigned long pm = acpi_pm_read_early();
+
+ if (cpu_has_tsc)
+ rdtscll(tsc);
+
+ switch (lapic_cal_loops++) {
+ case 0:
+ lapic_cal_t1 = tapic;
+ lapic_cal_tsc1 = tsc;
+ lapic_cal_pm1 = pm;
+ lapic_cal_j1 = jiffies;
+ break;
+
+ case LAPIC_CAL_LOOPS:
+ lapic_cal_t2 = tapic;
+ lapic_cal_tsc2 = tsc;
+ if (pm < lapic_cal_pm1)
+ pm += ACPI_PM_OVRRUN;
+ lapic_cal_pm2 = pm;
+ lapic_cal_j2 = jiffies;
+ break;
+ }
+}
+
+/*
+ * Setup the boot APIC
+ *
+ * Calibrate and verify the result.
+ */
+void __init setup_boot_APIC_clock(void)
{
- unsigned long long t1 = 0, t2 = 0;
- long tt1, tt2;
- long result;
- int i;
- const int LOOPS = HZ/10;
+ struct clock_event_device *levt = &__get_cpu_var(lapic_events);
+ const long pm_100ms = PMTMR_TICKS_PER_SEC/10;
+ const long pm_thresh = pm_100ms/100;
+ void (*real_handler)(struct clock_event_device *dev);
+ unsigned long deltaj;
+ long delta, deltapm;
+
+ apic_printk(APIC_VERBOSE, "Using local APIC timer interrupts.\n"
+ "calibrating APIC timer ...\n");
- apic_printk(APIC_VERBOSE, "calibrating APIC timer ...\n");
+ local_irq_disable();
+
+ /* Replace the global interrupt handler */
+ real_handler = global_clock_event->event_handler;
+ global_clock_event->event_handler = lapic_cal_handler;
/*
- * Put whatever arbitrary (but long enough) timeout
- * value into the APIC clock, we just want to get the
- * counter running for calibration.
+ * Setup the APIC counter to 1e9. There is no way the lapic
+ * can underflow in the 100ms detection time frame
*/
__setup_APIC_LVTT(1000000000, 0, 0);
- /*
- * The timer chip counts down to zero. Let's wait
- * for a wraparound to start exact measurement:
- * (the current tick might have been already half done)
- */
+ /* Let the interrupts run */
+ local_irq_enable();
- wait_timer_tick();
+ while(lapic_cal_loops <= LAPIC_CAL_LOOPS);
- /*
- * We wrapped around just now. Let's start:
- */
- if (cpu_has_tsc)
- rdtscll(t1);
- tt1 = apic_read(APIC_TMCCT);
+ local_irq_disable();
- /*
- * Let's wait LOOPS wraprounds:
- */
- for (i = 0; i < LOOPS; i++)
- wait_timer_tick();
+ /* Restore the real event handler */
+ global_clock_event->event_handler = real_handler;
- tt2 = apic_read(APIC_TMCCT);
- if (cpu_has_tsc)
- rdtscll(t2);
+ /* Build delta t1-t2 as apic timer counts down */
+ delta = lapic_cal_t1 - lapic_cal_t2;
+ apic_printk(APIC_VERBOSE, "... lapic delta = %ld\n", delta);
- /*
- * The APIC bus clock counter is 32 bits only, it
- * might have overflown, but note that we use signed
- * longs, thus no extra care needed.
- *
- * underflown to be exact, as the timer counts down ;)
- */
+ /* Check, if the PM timer is available */
+ deltapm = lapic_cal_pm2 - lapic_cal_pm1;
+ apic_printk(APIC_VERBOSE, "... PM timer delta = %ld\n", deltapm);
- result = (tt1-tt2)*APIC_DIVISOR/LOOPS;
+ if (deltapm) {
+ unsigned long mult;
+ u64 res;
+
+ mult = clocksource_hz2mult(PMTMR_TICKS_PER_SEC, 22);
+
+ if (deltapm > (pm_100ms - pm_thresh) &&
+ deltapm < (pm_100ms + pm_thresh)) {
+ apic_printk(APIC_VERBOSE, "... PM timer result ok\n");
+ } else {
+ res = (((u64) deltapm) * mult) >> 22;
+ do_div(res, 1000000);
+ printk(KERN_WARNING "APIC calibration not consistent "
+ "with PM Timer: %ldms instead of 100ms\n",
+ (long)res);
+ /* Correct the lapic counter value */
+ res = (((u64) delta ) * pm_100ms);
+ do_div(res, deltapm);
+ printk(KERN_INFO "APIC delta adjusted to PM-Timer: "
+ "%lu (%ld)\n", (unsigned long) res, delta);
+ delta = (long) res;
+ }
+ }
/* Calculate the scaled math multiplication factor */
- lapic_clockevent.mult = div_sc(tt1-tt2, TICK_NSEC * LOOPS, 32);
+ lapic_clockevent.mult = div_sc(delta, TICK_NSEC * LAPIC_CAL_LOOPS, 32);
lapic_clockevent.max_delta_ns =
clockevent_delta2ns(0x7FFFFF, &lapic_clockevent);
lapic_clockevent.min_delta_ns =
clockevent_delta2ns(0xF, &lapic_clockevent);
- apic_printk(APIC_VERBOSE, "..... tt1-tt2 %ld\n", tt1 - tt2);
+ calibration_result = (delta * APIC_DIVISOR) / LAPIC_CAL_LOOPS;
+
+ apic_printk(APIC_VERBOSE, "..... delta %ld\n", delta);
apic_printk(APIC_VERBOSE, "..... mult: %ld\n", lapic_clockevent.mult);
- apic_printk(APIC_VERBOSE, "..... calibration result: %ld\n", result);
+ apic_printk(APIC_VERBOSE, "..... calibration result: %u\n",
+ calibration_result);
- if (cpu_has_tsc)
+ if (cpu_has_tsc) {
+ delta = (long)(lapic_cal_tsc2 - lapic_cal_tsc1);
apic_printk(APIC_VERBOSE, "..... CPU clock speed is "
- "%ld.%04ld MHz.\n",
- ((long)(t2-t1)/LOOPS)/(1000000/HZ),
- ((long)(t2-t1)/LOOPS)%(1000000/HZ));
+ "%ld.%04ld MHz.\n",
+ (delta / LAPIC_CAL_LOOPS) / (1000000 / HZ),
+ (delta / LAPIC_CAL_LOOPS) % (1000000 / HZ));
+ }
apic_printk(APIC_VERBOSE, "..... host bus clock speed is "
- "%ld.%04ld MHz.\n",
- result/(1000000/HZ),
- result%(1000000/HZ));
-
- return result;
-}
+ "%u.%04u MHz.\n",
+ calibration_result / (1000000 / HZ),
+ calibration_result % (1000000 / HZ));
-void __init setup_boot_APIC_clock(void)
-{
- unsigned long flags;
- apic_printk(APIC_VERBOSE, "Using local APIC timer interrupts.\n");
- local_irq_save(flags);
+ apic_printk(APIC_VERBOSE, "... verify APIC timer\n");
- calibration_result = calibrate_APIC_clock();
/*
- * Now set up the timer for real.
+ * Setup the apic timer manually
*/
- setup_APIC_timer();
+ local_apic_timer_verify_ok = 1;
+ levt->event_handler = lapic_cal_handler;
+ lapic_timer_setup(CLOCK_EVT_MODE_PERIODIC, levt);
+ lapic_cal_loops = -1;
+
+ /* Let the interrupts run */
+ local_irq_enable();
+
+ while(lapic_cal_loops <= LAPIC_CAL_LOOPS);
+
+ local_irq_disable();
+
+ /* Stop the lapic timer */
+ lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, levt);
+
+ local_irq_enable();
+
+ /* Jiffies delta */
+ deltaj = lapic_cal_j2 - lapic_cal_j1;
+ apic_printk(APIC_VERBOSE, "... jiffies delta = %lu\n", deltaj);
+
+ /* Check, if the PM timer is available */
+ deltapm = lapic_cal_pm2 - lapic_cal_pm1;
+ apic_printk(APIC_VERBOSE, "... PM timer delta = %ld\n", deltapm);
+
+ local_apic_timer_verify_ok = 0;
+
+ if (deltapm) {
+ if (deltapm > (pm_100ms - pm_thresh) &&
+ deltapm < (pm_100ms + pm_thresh)) {
+ apic_printk(APIC_VERBOSE, "... PM timer result ok\n");
+ /* Check, if the jiffies result is consistent */
+ if (deltaj < LAPIC_CAL_LOOPS-2 ||
+ deltaj > LAPIC_CAL_LOOPS+2) {
+ /*
+ * Not sure, what we can do about this one.
+ * When high resultion timers are active
+ * and the lapic timer does not stop in C3
+ * we are fine. Otherwise more trouble might
+ * be waiting. -- tglx
+ */
+ printk(KERN_WARNING "Global event device %s "
+ "has wrong frequency "
+ "(%lu ticks instead of %d)\n",
+ global_clock_event->name, deltaj,
+ LAPIC_CAL_LOOPS);
+ }
+ local_apic_timer_verify_ok = 1;
+ }
+ } else {
+ /* Check, if the jiffies result is consistent */
+ if (deltaj >= LAPIC_CAL_LOOPS-2 &&
+ deltaj <= LAPIC_CAL_LOOPS+2) {
+ apic_printk(APIC_VERBOSE, "... jiffies result ok\n");
+ local_apic_timer_verify_ok = 1;
+ }
+ }
- local_irq_restore(flags);
+ if (!local_apic_timer_verify_ok) {
+ printk(KERN_WARNING
+ "APIC timer disabled due to verification failure.\n");
+ /* No broadcast on UP ! */
+ if (num_possible_cpus() == 1)
+ return;
+ } else
+ lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY;
+
+ /* Setup the lapic or request the broadcast */
+ setup_APIC_timer();
}
void __devinit setup_secondary_APIC_clock(void)
@@ -442,16 +515,15 @@ static void local_apic_timer_interrupt(void)
struct clock_event_device *evt = &per_cpu(lapic_events, cpu);
/*
- * Normally we should not be here till LAPIC has been
- * initialized but in some cases like kdump, its possible that
- * there is a pending LAPIC timer interrupt from previous
- * kernel's context and is delivered in new kernel the moment
- * interrupts are enabled.
+ * Normally we should not be here till LAPIC has been initialized but
+ * in some cases like kdump, its possible that there is a pending LAPIC
+ * timer interrupt from previous kernel's context and is delivered in
+ * new kernel the moment interrupts are enabled.
*
- * Interrupts are enabled early and LAPIC is setup much later,
- * hence its possible that when we get here evt->event_handler
- * is NULL. Check for event_handler being NULL and discard
- * the interrupt as spurious.
+ * Interrupts are enabled early and LAPIC is setup much later, hence
+ * its possible that when we get here evt->event_handler is NULL.
+ * Check for event_handler being NULL and discard the interrupt as
+ * spurious.
*/
if (!evt->event_handler) {
printk(KERN_WARNING
@@ -1126,13 +1198,6 @@ static int __init parse_nolapic(char *arg)
}
early_param("nolapic", parse_nolapic);
-static int __init apic_enable_lapic_timer(char *str)
-{
- enable_local_apic_timer = 1;
- return 0;
-}
-early_param("lapictimer", apic_enable_lapic_timer);
-
static int __init apic_set_verbosity(char *str)
{
if (strcmp("debug", str) == 0)