diff options
Diffstat (limited to 'Documentation')
52 files changed, 7529 insertions, 710 deletions
diff --git a/Documentation/ABI/removed/ip_queue b/Documentation/ABI/removed/ip_queue new file mode 100644 index 000000000000..3243613bc2d2 --- /dev/null +++ b/Documentation/ABI/removed/ip_queue @@ -0,0 +1,9 @@ +What: ip_queue +Date: finally removed in kernel v3.5.0 +Contact: Pablo Neira Ayuso <pablo@netfilter.org> +Description: + ip_queue has been replaced by nfnetlink_queue which provides + more advanced queueing mechanism to user-space. The ip_queue + module was already announced to become obsolete years ago. + +Users: diff --git a/Documentation/ABI/testing/sysfs-class-net-mesh b/Documentation/ABI/testing/sysfs-class-net-mesh index b218e0f8bdb3..c81fe89c4c46 100644 --- a/Documentation/ABI/testing/sysfs-class-net-mesh +++ b/Documentation/ABI/testing/sysfs-class-net-mesh @@ -14,6 +14,15 @@ Description: mesh will be sent using multiple interfaces at the same time (if available). +What: /sys/class/net/<mesh_iface>/mesh/bridge_loop_avoidance +Date: November 2011 +Contact: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> +Description: + Indicates whether the bridge loop avoidance feature + is enabled. This feature detects and avoids loops + between the mesh and devices bridged with the soft + interface <mesh_iface>. + What: /sys/class/net/<mesh_iface>/mesh/fragmentation Date: October 2010 Contact: Andreas Langer <an.langer@gmx.de> diff --git a/Documentation/DocBook/80211.tmpl b/Documentation/DocBook/80211.tmpl index c5ac6929c41c..f3e214f9e256 100644 --- a/Documentation/DocBook/80211.tmpl +++ b/Documentation/DocBook/80211.tmpl @@ -516,7 +516,7 @@ !Finclude/net/mac80211.h ieee80211_start_tx_ba_cb_irqsafe !Finclude/net/mac80211.h ieee80211_stop_tx_ba_session !Finclude/net/mac80211.h ieee80211_stop_tx_ba_cb_irqsafe -!Finclude/net/mac80211.h rate_control_changed +!Finclude/net/mac80211.h ieee80211_rate_control_changed !Finclude/net/mac80211.h ieee80211_tx_rate_control !Finclude/net/mac80211.h rate_control_send_low </chapter> diff --git a/Documentation/RCU/torture.txt b/Documentation/RCU/torture.txt index 375d3fb71437..4ddf3913fd8c 100644 --- a/Documentation/RCU/torture.txt +++ b/Documentation/RCU/torture.txt @@ -47,6 +47,16 @@ irqreader Says to invoke RCU readers from irq level. This is currently permit this. (Or, more accurately, variants of RCU that do -not- permit this know to ignore this variable.) +n_barrier_cbs If this is nonzero, RCU barrier testing will be conducted, + in which case n_barrier_cbs specifies the number of + RCU callbacks (and corresponding kthreads) to use for + this testing. The value cannot be negative. If you + specify this to be non-zero when torture_type indicates a + synchronous RCU implementation (one for which a member of + the synchronize_rcu() rather than the call_rcu() family is + used -- see the documentation for torture_type below), an + error will be reported and no testing will be carried out. + nfakewriters This is the number of RCU fake writer threads to run. Fake writer threads repeatedly use the synchronous "wait for current readers" function of the interface selected by @@ -188,7 +198,7 @@ OUTPUT The statistics output is as follows: rcu-torture:--- Start of test: nreaders=16 nfakewriters=4 stat_interval=30 verbose=0 test_no_idle_hz=1 shuffle_interval=3 stutter=5 irqreader=1 fqs_duration=0 fqs_holdoff=0 fqs_stutter=3 test_boost=1/0 test_boost_interval=7 test_boost_duration=4 - rcu-torture: rtc: (null) ver: 155441 tfle: 0 rta: 155441 rtaf: 8884 rtf: 155440 rtmbe: 0 rtbke: 0 rtbre: 0 rtbf: 0 rtb: 0 nt: 3055767 + rcu-torture: rtc: (null) ver: 155441 tfle: 0 rta: 155441 rtaf: 8884 rtf: 155440 rtmbe: 0 rtbe: 0 rtbke: 0 rtbre: 0 rtbf: 0 rtb: 0 nt: 3055767 rcu-torture: Reader Pipe: 727860534 34213 0 0 0 0 0 0 0 0 0 rcu-torture: Reader Batch: 727877838 17003 0 0 0 0 0 0 0 0 0 rcu-torture: Free-Block Circulation: 155440 155440 155440 155440 155440 155440 155440 155440 155440 155440 0 @@ -230,6 +240,9 @@ o "rtmbe": A non-zero value indicates that rcutorture believes that rcu_assign_pointer() and rcu_dereference() are not working correctly. This value should be zero. +o "rtbe": A non-zero value indicates that one of the rcu_barrier() + family of functions is not working correctly. + o "rtbke": rcutorture was unable to create the real-time kthreads used to force RCU priority inversion. This value should be zero. diff --git a/Documentation/arm/00-INDEX b/Documentation/arm/00-INDEX index 91c24a1e8a9e..36420e116c90 100644 --- a/Documentation/arm/00-INDEX +++ b/Documentation/arm/00-INDEX @@ -4,8 +4,6 @@ Booting - requirements for booting Interrupts - ARM Interrupt subsystem documentation -IXP2000 - - Release Notes for Linux on Intel's IXP2000 Network Processor msm - MSM specific documentation Netwinder diff --git a/Documentation/arm/IXP2000 b/Documentation/arm/IXP2000 deleted file mode 100644 index 68d21d92a30b..000000000000 --- a/Documentation/arm/IXP2000 +++ /dev/null @@ -1,69 +0,0 @@ - -------------------------------------------------------------------------- -Release Notes for Linux on Intel's IXP2000 Network Processor - -Maintained by Deepak Saxena <dsaxena@plexity.net> -------------------------------------------------------------------------- - -1. Overview - -Intel's IXP2000 family of NPUs (IXP2400, IXP2800, IXP2850) is designed -for high-performance network applications such high-availability -telecom systems. In addition to an XScale core, it contains up to 8 -"MicroEngines" that run special code, several high-end networking -interfaces (UTOPIA, SPI, etc), a PCI host bridge, one serial port, -flash interface, and some other odds and ends. For more information, see: - -http://developer.intel.com - -2. Linux Support - -Linux currently supports the following features on the IXP2000 NPUs: - -- On-chip serial -- PCI -- Flash (MTD/JFFS2) -- I2C through GPIO -- Timers (watchdog, OS) - -That is about all we can support under Linux ATM b/c the core networking -components of the chip are accessed via Intel's closed source SDK. -Please contact Intel directly on issues with using those. There is -also a mailing list run by some folks at Princeton University that might -be of help: https://lists.cs.princeton.edu/mailman/listinfo/ixp2xxx - -WHATEVER YOU DO, DO NOT POST EMAIL TO THE LINUX-ARM OR LINUX-ARM-KERNEL -MAILING LISTS REGARDING THE INTEL SDK. - -3. Supported Platforms - -- Intel IXDP2400 Reference Platform -- Intel IXDP2800 Reference Platform -- Intel IXDP2401 Reference Platform -- Intel IXDP2801 Reference Platform -- RadiSys ENP-2611 - -4. Usage Notes - -- The IXP2000 platforms usually have rather complex PCI bus topologies - with large memory space requirements. In addition, b/c of the way the - Intel SDK is designed, devices are enumerated in a very specific - way. B/c of this this, we use "pci=firmware" option in the kernel - command line so that we do not re-enumerate the bus. - -- IXDP2x01 systems have variable clock tick rates that we cannot determine - via HW registers. The "ixdp2x01_clk=XXX" cmd line options allow you - to pass the clock rate to the board port. - -5. Thanks - -The IXP2000 work has been funded by Intel Corp. and MontaVista Software, Inc. - -The following people have contributed patches/comments/etc: - -Naeem F. Afzal -Lennert Buytenhek -Jeffrey Daly - -------------------------------------------------------------------------- -Last Update: 8/09/2004 diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt new file mode 100644 index 000000000000..52478c83d0cc --- /dev/null +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -0,0 +1,27 @@ +* ARM architected timer + +ARM Cortex-A7 and Cortex-A15 have a per-core architected timer, which +provides per-cpu timers. + +The timer is attached to a GIC to deliver its per-processor interrupts. + +** Timer node properties: + +- compatible : Should at least contain "arm,armv7-timer". + +- interrupts : Interrupt list for secure, non-secure, virtual and + hypervisor timers, in that order. + +- clock-frequency : The frequency of the main counter, in Hz. Optional. + +Example: + + timer { + compatible = "arm,cortex-a15-timer", + "arm,armv7-timer"; + interrupts = <1 13 0xf08>, + <1 14 0xf08>, + <1 11 0xf08>, + <1 10 0xf08>; + clock-frequency = <100000000>; + }; diff --git a/Documentation/devicetree/bindings/ata/calxeda-sata.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index 79caa5651f53..8bb8a76d42e8 100644 --- a/Documentation/devicetree/bindings/ata/calxeda-sata.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -1,10 +1,10 @@ -* Calxeda SATA Controller +* AHCI SATA Controller SATA nodes are defined to describe on-chip Serial ATA controllers. Each SATA controller should have its own node. Required properties: -- compatible : compatible list, contains "calxeda,hb-ahci" +- compatible : compatible list, contains "calxeda,hb-ahci" or "snps,spear-ahci" - interrupts : <interrupt mapping for SATA IRQ> - reg : <registers mapping> @@ -14,4 +14,3 @@ Example: reg = <0xffe08000 0x1000>; interrupts = <115>; }; - diff --git a/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt new file mode 100644 index 000000000000..79384113c2b0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt @@ -0,0 +1,127 @@ +Properties for an MDIO bus multiplexer/switch controlled by GPIO pins. + +This is a special case of a MDIO bus multiplexer. One or more GPIO +lines are used to control which child bus is connected. + +Required properties in addition to the generic multiplexer properties: + +- compatible : mdio-mux-gpio. +- gpios : GPIO specifiers for each GPIO line. One or more must be specified. + + +Example : + + /* The parent MDIO bus. */ + smi1: mdio@1180000001900 { + compatible = "cavium,octeon-3860-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0x00001900 0x0 0x40>; + }; + + /* + An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a + pair of GPIO lines. Child busses 2 and 3 populated with 4 + PHYs each. + */ + mdio-mux { + compatible = "mdio-mux-gpio"; + gpios = <&gpio1 3 0>, <&gpio1 4 0>; + mdio-parent-bus = <&smi1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy11: ethernet-phy@1 { + reg = <1>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy12: ethernet-phy@2 { + reg = <2>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy13: ethernet-phy@3 { + reg = <3>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy14: ethernet-phy@4 { + reg = <4>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + }; + + mdio@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + phy21: ethernet-phy@1 { + reg = <1>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy22: ethernet-phy@2 { + reg = <2>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy23: ethernet-phy@3 { + reg = <3>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy24: ethernet-phy@4 { + reg = <4>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt new file mode 100644 index 000000000000..f65606f8d632 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux.txt @@ -0,0 +1,136 @@ +Common MDIO bus multiplexer/switch properties. + +An MDIO bus multiplexer/switch will have several child busses that are +numbered uniquely in a device dependent manner. The nodes for an MDIO +bus multiplexer/switch will have one child node for each child bus. + +Required properties: +- mdio-parent-bus : phandle to the parent MDIO bus. +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Other properties specific to the multiplexer/switch hardware. + +Required properties for child nodes: +- #address-cells = <1>; +- #size-cells = <0>; +- reg : The sub-bus number. + + +Example : + + /* The parent MDIO bus. */ + smi1: mdio@1180000001900 { + compatible = "cavium,octeon-3860-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0x00001900 0x0 0x40>; + }; + + /* + An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a + pair of GPIO lines. Child busses 2 and 3 populated with 4 + PHYs each. + */ + mdio-mux { + compatible = "mdio-mux-gpio"; + gpios = <&gpio1 3 0>, <&gpio1 4 0>; + mdio-parent-bus = <&smi1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy11: ethernet-phy@1 { + reg = <1>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy12: ethernet-phy@2 { + reg = <2>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy13: ethernet-phy@3 { + reg = <3>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy14: ethernet-phy@4 { + reg = <4>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + }; + + mdio@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + phy21: ethernet-phy@1 { + reg = <1>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy22: ethernet-phy@2 { + reg = <2>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy23: ethernet-phy@3 { + reg = <3>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy24: ethernet-phy@4 { + reg = <4>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt new file mode 100644 index 000000000000..ab19e6bc7d3b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt @@ -0,0 +1,95 @@ +* Freescale IOMUX Controller (IOMUXC) for i.MX + +The IOMUX Controller (IOMUXC), together with the IOMUX, enables the IC +to share one PAD to several functional blocks. The sharing is done by +multiplexing the PAD input/output signals. For each PAD there are up to +8 muxing options (called ALT modes). Since different modules require +different PAD settings (like pull up, keeper, etc) the IOMUXC controls +also the PAD settings parameters. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Freescale IMX pin configuration node is a node of a group of pins which can be +used for a specific device or function. This node represents both mux and config +of the pins in that group. The 'mux' selects the function mode(also named mux +mode) this pin can work on and the 'config' configures various pad settings +such as pull-up, open drain, drive strength, etc. + +Required properties for iomux controller: +- compatible: "fsl,<soc>-iomuxc" + Please refer to each fsl,<soc>-pinctrl.txt binding doc for supported SoCs. + +Required properties for pin configuration node: +- fsl,pins: two integers array, represents a group of pins mux and config + setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a + pin working on a specific function, CONFIG is the pad setting value like + pull-up on this pin. Please refer to fsl,<soc>-pinctrl.txt for the valid + pins and functions of each SoC. + +Bits used for CONFIG: +NO_PAD_CTL(1 << 31): indicate this pin does not need config. + +SION(1 << 30): Software Input On Field. +Force the selected mux mode input path no matter of MUX_MODE functionality. +By default the input path is determined by functionality of the selected +mux mode (regular). + +Other bits are used for PAD setting. +Please refer to each fsl,<soc>-pinctrl,txt binding doc for SoC specific part +of bits definitions. + +NOTE: +Some requirements for using fsl,imx-pinctrl binding: +1. We have pin function node defined under iomux controller node to represent + what pinmux functions this SoC supports. +2. The pin configuration node intends to work on a specific function should + to be defined under that specific function node. + The function node's name should represent well about what function + this group of pins in this pin configuration node are working on. +3. The driver can use the function node's name and pin configuration node's + name describe the pin function and group hierarchy. + For example, Linux IMX pinctrl driver takes the function node's name + as the function name and pin configuration node's name as group name to + create the map table. |