diff options
Diffstat (limited to 'Documentation/kbuild')
| -rw-r--r-- | Documentation/kbuild/makefiles.rst | 88 |
1 files changed, 40 insertions, 48 deletions
diff --git a/Documentation/kbuild/makefiles.rst b/Documentation/kbuild/makefiles.rst index 9636e81bed78..87ff7c677749 100644 --- a/Documentation/kbuild/makefiles.rst +++ b/Documentation/kbuild/makefiles.rst @@ -18,7 +18,7 @@ This document describes the Linux kernel Makefiles. --- 3.7 Compilation flags --- 3.8 <deleted> --- 3.9 Dependency tracking - --- 3.10 Special Rules + --- 3.10 Custom Rules --- 3.11 $(CC) support functions --- 3.12 $(LD) support functions --- 3.13 Script Invocation @@ -46,7 +46,7 @@ This document describes the Linux kernel Makefiles. --- 7.5 Architecture-specific boot images --- 7.6 Building non-kbuild targets --- 7.7 Commands useful for building a boot image - --- 7.8 Custom kbuild commands + --- 7.8 <deleted> --- 7.9 Preprocessing linker scripts --- 7.10 Generic header files --- 7.11 Post-link pass @@ -422,21 +422,21 @@ more details, with real examples. Thus, if you change an option to $(CC) all affected files will be re-compiled. -3.10 Special Rules +3.10 Custom Rules ------------------ - Special rules are used when the kbuild infrastructure does + Custom rules are used when the kbuild infrastructure does not provide the required support. A typical example is header files generated during the build process. Another example are the architecture-specific Makefiles which - need special rules to prepare boot images etc. + need custom rules to prepare boot images etc. - Special rules are written as normal Make rules. + Custom rules are written as normal Make rules. Kbuild is not executing in the directory where the Makefile is - located, so all special rules shall provide a relative + located, so all custom rules shall use a relative path to prerequisite files and target files. - Two variables are used when defining special rules: + Two variables are used when defining custom rules: $(src) $(src) is a relative path which points to the directory @@ -454,7 +454,7 @@ more details, with real examples. $(obj)/53c8xx_d.h: $(src)/53c7,8xx.scr $(src)/script_asm.pl $(CPP) -DCHIP=810 - < $< | ... $(src)/script_asm.pl - This is a special rule, following the normal syntax + This is a custom rule, following the normal syntax required by make. The target file depends on two prerequisite files. References @@ -471,11 +471,33 @@ more details, with real examples. Example:: - #arch/blackfin/boot/Makefile - $(obj)/vmImage: $(obj)/vmlinux.gz - $(call if_changed,uimage) - @$(kecho) 'Kernel: $@ is ready' + # arch/arm/Makefile + $(BOOT_TARGETS): vmlinux + $(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/$@ + @$(kecho) ' Kernel: $(boot)/$@ is ready' + When kbuild is executing with KBUILD_VERBOSE=0, then only a shorthand + of a command is normally displayed. + To enable this behaviour for custom commands kbuild requires + two variables to be set:: + + quiet_cmd_<command> - what shall be echoed + cmd_<command> - the command to execute + + Example:: + + # lib/Makefile + quiet_cmd_crc32 = GEN $@ + cmd_crc32 = $< > $@ + + $(obj)/crc32table.h: $(obj)/gen_crc32table + $(call cmd,crc32) + + When updating the $(obj)/crc32table.h target, the line: + + GEN lib/crc32table.h + + will be displayed with "make KBUILD_VERBOSE=0". 3.11 $(CC) support functions ---------------------------- @@ -744,7 +766,7 @@ Both possibilities are described in the following. as a prerequisite. This is possible in two ways: - (1) List the prerequisite explicitly in a special rule. + (1) List the prerequisite explicitly in a custom rule. Example:: @@ -755,11 +777,11 @@ Both possibilities are described in the following. The target $(obj)/devlist.h will not be built before $(obj)/gen-devlist is updated. Note that references to - the host programs in special rules must be prefixed with $(obj). + the host programs in custom rules must be prefixed with $(obj). (2) Use always-y - When there is no suitable special rule, and the host program + When there is no suitable custom rule, and the host program shall be built when a makefile is entered, the always-y variable shall be used. @@ -1281,8 +1303,8 @@ When kbuild executes, the following steps are followed (roughly): otherwise the command line check will fail, and the target will always be built. Assignments to $(targets) are without $(obj)/ prefix. - if_changed may be used in conjunction with custom commands as - defined in 7.8 "Custom kbuild commands". + if_changed may be used in conjunction with custom rules as + defined in "3.10 Custom Rules". Note: It is a typical mistake to forget the FORCE prerequisite. Another common pitfall is that whitespace is sometimes @@ -1362,36 +1384,6 @@ When kbuild executes, the following steps are followed (roughly): targets += $(dtb-y) DTC_FLAGS ?= -p 1024 -7.8 Custom kbuild commands --------------------------- - - When kbuild is executing with KBUILD_VERBOSE=0, then only a shorthand - of a command is normally displayed. - To enable this behaviour for custom commands kbuild requires - two variables to be set:: - - quiet_cmd_<command> - what shall be echoed - cmd_<command> - the command to execute - - Example:: - - # - quiet_cmd_image = BUILD $@ - cmd_image = $(obj)/tools/build $(BUILDFLAGS) \ - $(obj)/vmlinux.bin > $@ - - targets += bzImage - $(obj)/bzImage: $(obj)/vmlinux.bin $(obj)/tools/build FORCE - $(call if_changed,image) - @echo 'Kernel: $@ is ready' - - When updating the $(obj)/bzImage target, the line: - - BUILD arch/x86/boot/bzImage - - will be displayed with "make KBUILD_VERBOSE=0". - - 7.9 Preprocessing linker scripts -------------------------------- |