diff options
Diffstat (limited to 'Documentation/devicetree')
23 files changed, 203 insertions, 32 deletions
diff --git a/Documentation/devicetree/bindings/arm/gic-v3.txt b/Documentation/devicetree/bindings/arm/gic-v3.txt index ddfade40ac59..7803e77d85cb 100644 --- a/Documentation/devicetree/bindings/arm/gic-v3.txt +++ b/Documentation/devicetree/bindings/arm/gic-v3.txt @@ -57,6 +57,8 @@ used to route Message Signalled Interrupts (MSI) to the CPUs. These nodes must have the following properties: - compatible : Should at least contain "arm,gic-v3-its". - msi-controller : Boolean property. Identifies the node as an MSI controller +- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device + which will generate the MSI. - reg: Specifies the base physical address and size of the ITS registers. @@ -83,6 +85,7 @@ Examples: gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c200000 0 0x200000>; }; }; @@ -107,12 +110,14 @@ Examples: gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c200000 0 0x200000>; }; gic-its@2c400000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c400000 0 0x200000>; }; }; diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt index a8274eabae2e..b8e41c148a3c 100644 --- a/Documentation/devicetree/bindings/arm/idle-states.txt +++ b/Documentation/devicetree/bindings/arm/idle-states.txt @@ -497,7 +497,7 @@ cpus { }; idle-states { - entry-method = "arm,psci"; + entry-method = "psci"; CPU_RETENTION_0_0: cpu-retention-0-0 { compatible = "arm,idle-state"; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 5788d5cf1252..82d40e2505f6 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -16,7 +16,9 @@ properties, each containing a 'gpio-list': GPIO properties should be named "[<name>-]gpios", with <name> being the purpose of this GPIO for the device. While a non-existent <name> is considered valid for compatibility reasons (resolving to the "gpios" property), it is not allowed -for new bindings. +for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old +bindings use it, but are only supported for compatibility reasons and should not +be used for newer bindings since it has been deprecated. GPIO properties can contain one or more GPIO phandles, but only in exceptional cases should they contain more than one. If your device uses several GPIOs with diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt index c5933573e0f6..4a3679d54457 100644 --- a/Documentation/devicetree/bindings/iio/accel/bma180.txt +++ b/Documentation/devicetree/bindings/iio/accel/bma180.txt @@ -1,10 +1,11 @@ -* Bosch BMA180 triaxial acceleration sensor +* Bosch BMA180 / BMA250 triaxial acceleration sensor http://omapworld.com/BMA180_111_1002839.pdf +http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf Required properties: - - compatible : should be "bosch,bma180" + - compatible : should be "bosch,bma180" or "bosch,bma250" - reg : the I2C address of the sensor Optional properties: @@ -13,6 +14,9 @@ Optional properties: - interrupts : interrupt mapping for GPIO IRQ, it should by configured with flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING + For the bma250 the first interrupt listed must be the one + connected to the INT1 pin, the second (optional) interrupt + listed must be the one connected to the INT2 pin. Example: diff --git a/Documentation/devicetree/bindings/input/cypress,cyapa.txt b/Documentation/devicetree/bindings/input/cypress,cyapa.txt index 635a3b036630..8d91ba9ff2fd 100644 --- a/Documentation/devicetree/bindings/input/cypress,cyapa.txt +++ b/Documentation/devicetree/bindings/input/cypress,cyapa.txt @@ -25,7 +25,7 @@ Example: /* Cypress Gen3 touchpad */ touchpad@67 { compatible = "cypress,cyapa"; - reg = <0x24>; + reg = <0x67>; interrupt-parent = <&gpio>; interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO 2 */ wakeup-source; diff --git a/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt index 391717a68f3b..ec96b1f01478 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt @@ -4,8 +4,8 @@ The MISC interrupt controller is a secondary controller for lower priority interrupt. Required Properties: -- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" - as fallback +- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" or + "qca,<soctype>-cpu-intc", "qca,ar7240-misc-intc" - reg: Base address and size of the controllers memory area - interrupt-parent: phandle of the parent interrupt controller. - interrupts: Interrupt specifier for the controllers interrupt. @@ -13,6 +13,9 @@ Required Properties: - #interrupt-cells : Specifies the number of cells needed to encode interrupt source, should be 1 +Compatible fallback depends on the SoC. Use ar7100 for ar71xx and ar913x, +use ar7240 for all other SoCs. + Please refer to interrupts.txt in this directory for details of the common Interrupt Controllers bindings used by client devices. @@ -28,3 +31,16 @@ Example: interrupt-controller; #interrupt-cells = <1>; }; + +Another example: + + interrupt-controller@18060010 { + compatible = "qca,ar9331-misc-intc", qca,ar7240-misc-intc"; + reg = <0x18060010 0x4>; + + interrupt-parent = <&cpuintc>; + interrupts = <6>; + + interrupt-controller; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index 41811223e5be..a474359dd206 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -60,8 +60,8 @@ DCDC2 : DC-DC buck : vin2-supply DCDC3 : DC-DC buck : vin3-supply DCDC4 : DC-DC buck : vin4-supply DCDC5 : DC-DC buck : vin5-supply -DC1SW : On/Off Switch : dcdc1-supply : DCDC1 secondary output -DC5LDO : LDO : dcdc5-supply : input from DCDC5 +DC1SW : On/Off Switch : : DCDC1 secondary output +DC5LDO : LDO : : input from DCDC5 ALDO1 : LDO : aldoin-supply : shared supply ALDO2 : LDO : aldoin-supply : shared supply ALDO3 : LDO : aldoin-supply : shared supply diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index a9df21aaa154..a2cae4eb4a60 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -39,6 +39,7 @@ Required properties: Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports - mac-address : See ethernet.txt file in the same directory +- phy-handle : See ethernet.txt file in the same directory Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/net/smsc-lan87xx.txt b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt new file mode 100644 index 000000000000..974edd5c85cc --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt @@ -0,0 +1,24 @@ +SMSC LAN87xx Ethernet PHY + +Some boards require special tuning values. Configure them +through an Ethernet OF device node. + +Optional properties: + +- smsc,disable-energy-detect: + If set, do not enable energy detect mode for the SMSC phy. + default: enable energy detect mode + +Examples: +smsc phy with disabled energy detect mode on an am335x based board. +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; + + ethernetphy0: ethernet-phy@0 { + reg = <0>; + smsc,disable-energy-detect; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index d8ef5bf50f11..7fab84b33531 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -7,7 +7,8 @@ OHCI and EHCI controllers. Required properties: - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; - "renesas,pci-r8a7791" for the R8A7791 SoC. + "renesas,pci-r8a7791" for the R8A7791 SoC; + "renesas,pci-r8a7794" for the R8A7794 SoC. - reg: A list of physical regions to access the device: the first is the operational registers for the OHCI/EHCI controllers and the second is for the bridge configuration and control registers. diff --git a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt index e91485d11241..6067d9830d07 100644 --- a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt @@ -8,6 +8,8 @@ Required properties: Optional properties: - system-power-controller: Telling whether or not this pmic is controlling the system power. See Documentation/devicetree/bindings/power/power-controller.txt . +- active-semi,vsel-high: Indicates the VSEL pin is high. + If this property is missing, assume the VSEL pin is low(0). Optional input supply properties: - for act8600: @@ -49,6 +51,7 @@ Example: pmic: act8865@5b { compatible = "active-semi,act8865"; reg = <0x5b>; + active-semi,vsel-high; status = "disabled"; regulators { diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt index 758eae24082a..37c4ea076f88 100644 --- a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -13,6 +13,7 @@ Optional properties: - anatop-delay-reg-offset: Anatop MFD step time register offset - anatop-delay-bit-shift: Bit shift for the step time register - anatop-delay-bit-width: Number of bits used in the step time register +- vin-supply: The supply for this regulator Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. diff --git a/Documentation/devicetree/bindings/regulator/arizona-regulator.txt b/Documentation/devicetree/bindings/regulator/arizona-regulator.txt new file mode 100644 index 000000000000..443564d7784f --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/arizona-regulator.txt @@ -0,0 +1,17 @@ +Cirrus Logic Arizona class audio SoCs + +These devices are audio SoCs with extensive digital capabilities and a range +of analogue I/O. + +This document lists regulator specific bindings, see the primary binding +document: + ../mfd/arizona.txt + +Optional properties: + - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA + +Optional subnodes: + - ldo1 : Initial data for the LDO1 regulator, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt + - micvdd : Initial data for the MICVDD regulator, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/regulator/max77802.txt b/Documentation/devicetree/bindings/regulator/max77802.txt index 79e5476444f7..09d796ed48be 100644 --- a/Documentation/devicetree/bindings/regulator/max77802.txt +++ b/Documentation/devicetree/bindings/regulator/max77802.txt @@ -8,7 +8,28 @@ regulators that can be controlled over I2C. Following properties should be present in main device node of the MFD chip. -Optional node: +Optional properties: +- inb1-supply: The input supply for BUCK1 +- inb2-supply: The input supply for BUCK2 +- inb3-supply: The input supply for BUCK3 +- inb4-supply: The input supply for BUCK4 +- inb5-supply: The input supply for BUCK5 +- inb6-supply: The input supply for BUCK6 +- inb7-supply: The input supply for BUCK7 +- inb8-supply: The input supply for BUCK8 +- inb9-supply: The input supply for BUCK9 +- inb10-supply: The input supply for BUCK10 +- inl1-supply: The input supply for LDO8 and LDO15 +- inl2-supply: The input supply for LDO17, LDO27, LDO30 and LDO35 +- inl3-supply: The input supply for LDO3, LDO5, LDO6 and LDO7 +- inl4-supply: The input supply for LDO10, LDO11, LDO13 and LDO14 +- inl5-supply: The input supply for LDO9 and LDO19 +- inl6-supply: The input supply for LDO4, LDO21, LDO24 and LDO33 +- inl7-supply: The input supply for LDO18, LDO20, LDO28 and LDO29 +- inl9-supply: The input supply for LDO12, LDO23, LDO25, LDO26, LDO32 and LDO34 +- inl10-supply: The input supply for LDO1 and LDO2 + +Optional nodes: - regulators : The regulators of max77802 have to be instantiated under subnode named "regulators" using the following format. @@ -58,6 +79,8 @@ Example: #address-cells = <1>; #size-cells = <0>; + inb1-supply = <&parent_reg>; + regulators { ldo1_reg: LDO1 { regulator-name = "vdd_1v0"; diff --git a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt index 32aa26f1e434..acbcb452a69a 100644 --- a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt @@ -2,7 +2,12 @@ PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs. Required properties: - compatible: - - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7. + - should be "ti,pbias-dra7" for DRA7 + - should be "ti,pbias-omap2" for OMAP2 + - should be "ti,pbias-omap3" for OMAP3 + - should be "ti,pbias-omap4" for OMAP4 + - should be "ti,pbias-omap5" for OMAP5 + - "ti,pbias-omap" is deprecated - reg: pbias register offset from syscon base and size of pbias register. - syscon : phandle of the system control module - regulator-name : should be diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 24bd422cecd5..1d112fc456aa 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -11,6 +11,7 @@ Optional properties: - regulator-always-on: boolean, regulator should never be disabled - regulator-boot-on: bootloader/firmware enabled regulator - regulator-allow-bypass: allow the regulator to go into bypass mode +- regulator-allow-set-load: allow the regulator performance level to be configured - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) For hardware which supports disabling ramp rate, it should be explicitly diff --git a/Documentation/devicetree/bindings/regulator/tps65023.txt b/Documentation/devicetree/bindings/regulator/tps65023.txt new file mode 100644 index 000000000000..a4714e4da370 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65023.txt @@ -0,0 +1,60 @@ +TPS65023 family of regulators + +Required properties: +- compatible: Must be one of the following. + "ti,tps65020", + "ti,tps65021", + "ti,tps65023", +- reg: I2C slave address +- regulators: list of regulators provided by this controller, must be named + after their hardware counterparts: VDCDC[1-3] and LDO[1-2] +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. The definition for each of + these nodes is defined using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps65023@48 { + compatible = "ti,tps65023"; + reg = <0x48>; + + regulators { + VDCDC1 { + regulator-name = "vdd_mpu"; + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + VDCDC2 { + regulator-name = "vdd_core"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + VDCDC3 { + regulator-name = "vdd_io"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + LDO1 { + regulator-name = "vdd_usb18"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + LDO2 { + regulator-name = "vdd_usb33"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index 8f771441be60..705075da2f10 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -51,7 +51,7 @@ Optional properties, deprecated for soctype-specific bindings: - renesas,tx-fifo-size : Overrides the default tx fifo size given in words (default is 64) - renesas,rx-fifo-size : Overrides the default rx fifo size given in words - (default is 64, or 256 on R-Car Gen2) + (default is 64) Pinctrl properties might be needed, too. See Documentation/devicetree/bindings/pinctrl/renesas,*. diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index dcefc438272f..6160ffbcb3d3 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -15,17 +15,18 @@ Required properties: - interrupts: Should contain spi interrupt - clocks: phandles to input clocks. - The first should be <&topckgen CLK_TOP_SPI_SEL>. - The second should be one of the following. + The first should be one of the following. It's PLL. - <&clk26m>: specify parent clock 26MHZ. - <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ. It's the default one. - <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ. - <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ. - <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ. + The second should be <&topckgen CLK_TOP_SPI_SEL>. It's clock mux. + The third is <&pericfg CLK_PERI_SPI0>. It's clock gate. -- clock-names: shall be "spi-clk" for the controller clock, and - "parent-clk" for the parent clock. +- clock-names: shall be "parent-clk" for the parent clock, "sel-clk" for the + muxes clock, and "spi-clk" for the clock gate. Optional properties: - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi @@ -44,8 +45,11 @@ spi: spi@1100a000 { #size-cells = <0>; reg = <0 0x1100a000 0 0x1000>; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>; - clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>; - clock-names = "spi-clk", "parent-clk"; + clocks = <&topckgen CLK_TOP_SYSPLL3_D2>, + <&topckgen CLK_TOP_SPI_SEL>, + <&pericfg CLK_PERI_SPI0>; + clock-names = "parent-clk", "sel-clk", "spi-clk"; + mediatek,pad-select = <0>; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index 8a49362dea6e..41b817f7b670 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -55,19 +55,11 @@ of heat dissipation). For example a fan's cooling states correspond to the different fan speeds possible. Cooling states are referred to by single unsigned integers, where larger numbers mean greater heat dissipation. The precise set of cooling states associated with a device -(as referred to be the cooling-min-state and cooling-max-state +(as referred to by the cooling-min-level and cooling-max-level properties) should be defined in a particular device's binding. For more examples of cooling devices, refer to the example sections below. Required properties: -- cooling-min-state: An integer indicating the smallest - Type: unsigned cooling state accepted. Typically 0. - Size: one cell - -- cooling-max-state: An integer indicating the largest - Type: unsigned cooling state accepted. - Size: one cell - - #cooling-cells: Used to provide cooling device specific information Type: unsigned while referring to it. Must be at least 2, in order Size: one cell to specify minimum and maximum cooling state used @@ -77,6 +69,15 @@ Required properties: See Cooling device maps section below for more details on how consumers refer to cooling devices. +Optional properties: +- cooling-min-level: An integer indicating the smallest + Type: unsigned cooling state accepted. Typically 0. + Size: one cell + +- cooling-max-level: An integer indicating the largest + Type: unsigned cooling state accepted. + Size: one cell + * Trip points The trip node is a node to describe a point in the temperature domain @@ -225,8 +226,8 @@ cpus { 396000 950000 198000 850000 >; - cooling-min-state = <0>; - cooling-max-state = <3>; + cooling-min-level = <0>; + cooling-max-level = <3>; #cooling-cells = <2>; /* min followed by max */ }; ... @@ -240,8 +241,8 @@ cpus { */ fan0: fan@0x48 { ... - cooling-min-state = <0>; - cooling-max-state = <9>; + cooling-min-level = <0>; + cooling-max-level = <9>; #cooling-cells = <2>; /* min followed by max */ }; }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index d71ef07bca5d..a057b75ba4b5 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -6,6 +6,7 @@ Required properties: "lsi,zevio-usb" "qcom,ci-hdrc" "chipidea,usb2" + "xlnx,zynq-usb-2.20a" - reg: base address and length of the registers - interrupts: interrupt for the USB controller diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 64a4ca6cf96f..7d48f63db44e 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -5,6 +5,7 @@ Required properties: - "renesas,usbhs-r8a7790" - "renesas,usbhs-r8a7791" - "renesas,usbhs-r8a7794" + - "renesas,usbhs-r8a7795" - reg: Base address and length of the register for the USBHS - interrupts: Interrupt specifier for the USBHS - clocks: A list of phandle + clock specifier pairs diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index ac5f0c34ae00..82d2ac97af74 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -203,6 +203,7 @@ sitronix Sitronix Technology Corporation skyworks Skyworks Solutions, Inc. smsc Standard Microsystems Corporation snps Synopsys, Inc. +socionext Socionext Inc. solidrun SolidRun solomon Solomon Systech Limited sony Sony Corporation |