diff options
Diffstat (limited to 'Documentation/devicetree')
5 files changed, 173 insertions, 12 deletions
diff --git a/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt index 5626560a6cfd..8f52206cfd2a 100644 --- a/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt +++ b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt @@ -232,37 +232,152 @@ Example: }; }; -Stratix10 SoCFPGA ECC Manager +Stratix10 SoCFPGA ECC Manager (ARM64) The Stratix10 SoC ECC Manager handles the IRQs for each peripheral -in a shared register similar to the Arria10. However, ECC requires -access to registers that can only be read from Secure Monitor with -SMC calls. Therefore the device tree is slightly different. +in a shared register similar to the Arria10. However, Stratix10 ECC +requires access to registers that can only be read from Secure Monitor +with SMC calls. Therefore the device tree is slightly different. Note +that only 1 interrupt is sent in Stratix10 because the double bit errors +are treated as SErrors in ARM64 instead of IRQs in ARM32. Required Properties: - compatible : Should be "altr,socfpga-s10-ecc-manager" -- interrupts : Should be single bit error interrupt, then double bit error - interrupt. +- altr,sysgr-syscon : phandle to Stratix10 System Manager Block + containing the ECC manager registers. +- interrupts : Should be single bit error interrupt. - interrupt-controller : boolean indicator that ECC Manager is an interrupt controller - #interrupt-cells : must be set to 2. +- #address-cells: must be 1 +- #size-cells: must be 1 +- ranges : standard definition, should translate from local addresses Subcomponents: SDRAM ECC Required Properties: - compatible : Should be "altr,sdram-edac-s10" -- interrupts : Should be single bit error interrupt, then double bit error - interrupt, in this order. +- interrupts : Should be single bit error interrupt. + +On-Chip RAM ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-ocram-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent OCRAM node. +- interrupts : Should be single bit error interrupt. + +Ethernet FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-eth-mac-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent Ethernet node. +- interrupts : Should be single bit error interrupt. + +NAND FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-nand-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent NAND node. +- interrupts : Should be single bit error interrupt. + +DMA FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-dma-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent DMA node. +- interrupts : Should be single bit error interrupt. + +USB FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-usb-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent USB node. +- interrupts : Should be single bit error interrupt. + +SDMMC FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-sdmmc-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent SD/MMC node. +- interrupts : Should be single bit error interrupt for port A + and then single bit error interrupt for port B. Example: eccmgr { compatible = "altr,socfpga-s10-ecc-manager"; - interrupts = <0 15 4>, <0 95 4>; + altr,sysmgr-syscon = <&sysmgr>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = <0 15 4>; interrupt-controller; #interrupt-cells = <2>; + ranges; sdramedac { compatible = "altr,sdram-edac-s10"; - interrupts = <16 4>, <48 4>; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH>; + }; + + ocram-ecc@ff8cc000 { + compatible = "altr,socfpga-s10-ocram-ecc"; + reg = <ff8cc000 0x100>; + altr,ecc-parent = <&ocram>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; + }; + + emac0-rx-ecc@ff8c0000 { + compatible = "altr,socfpga-s10-eth-mac-ecc"; + reg = <0xff8c0000 0x100>; + altr,ecc-parent = <&gmac0>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; + }; + + emac0-tx-ecc@ff8c0400 { + compatible = "altr,socfpga-s10-eth-mac-ecc"; + reg = <0xff8c0400 0x100>; + altr,ecc-parent = <&gmac0>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>' + }; + + nand-buf-ecc@ff8c8000 { + compatible = "altr,socfpga-s10-nand-ecc"; + reg = <0xff8c8000 0x100>; + altr,ecc-parent = <&nand>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + }; + + nand-rd-ecc@ff8c8400 { + compatible = "altr,socfpga-s10-nand-ecc"; + reg = <0xff8c8400 0x100>; + altr,ecc-parent = <&nand>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; + }; + + nand-wr-ecc@ff8c8800 { + compatible = "altr,socfpga-s10-nand-ecc"; + reg = <0xff8c8800 0x100>; + altr,ecc-parent = <&nand>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>; + }; + + dma-ecc@ff8c9000 { + compatible = "altr,socfpga-s10-dma-ecc"; + reg = <0xff8c9000 0x100>; + altr,ecc-parent = <&pdma>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; + + usb0-ecc@ff8c4000 { + compatible = "altr,socfpga-s10-usb-ecc"; + reg = <0xff8c4000 0x100>; + altr,ecc-parent = <&usb0>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + }; + + sdmmc-ecc@ff8c8c00 { + compatible = "altr,socfpga-s10-sdmmc-ecc"; + reg = <0xff8c8c00 0x100>; + altr,ecc-parent = <&mmc>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH>, + <15 IRQ_TYPE_LEVEL_HIGH>; }; }; diff --git a/Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt new file mode 100644 index 000000000000..ffb79ccf51ee --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt @@ -0,0 +1,26 @@ +Cirrus Logic Lochnagar Audio Development Board + +Lochnagar is an evaluation and development board for Cirrus Logic +Smart CODEC and Amp devices. It allows the connection of most Cirrus +Logic devices on mini-cards, as well as allowing connection of +various application processor systems to provide a full evaluation +platform. Audio system topology, clocking and power can all be +controlled through the Lochnagar, allowing the device under test +to be used in a variety of possible use cases. + +This binding document describes the binding for the hardware monitor +portion of the driver. + +This binding must be part of the Lochnagar MFD binding: + [4] ../mfd/cirrus,lochnagar.txt + +Required properties: + + - compatible : One of the following strings: + "cirrus,lochnagar2-hwmon" + +Example: + +lochnagar-hwmon { + compatible = "cirrus,lochnagar2-hwmon"; +}; diff --git a/Documentation/devicetree/bindings/hwmon/g762.txt b/Documentation/devicetree/bindings/hwmon/g762.txt index 25cc6d8ee575..6d154c4923de 100644 --- a/Documentation/devicetree/bindings/hwmon/g762.txt +++ b/Documentation/devicetree/bindings/hwmon/g762.txt @@ -21,7 +21,7 @@ If an optional property is not set in .dts file, then current value is kept unmodified (e.g. u-boot installed value). Additional information on operational parameters for the device is available -in Documentation/hwmon/g762. A detailed datasheet for the device is available +in Documentation/hwmon/g762.rst. A detailed datasheet for the device is available at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf. Example g762 node: diff --git a/Documentation/devicetree/bindings/hwmon/lm75.txt b/Documentation/devicetree/bindings/hwmon/lm75.txt index 12d8cf7cf592..586b5ed70be7 100644 --- a/Documentation/devicetree/bindings/hwmon/lm75.txt +++ b/Documentation/devicetree/bindings/hwmon/lm75.txt @@ -25,6 +25,7 @@ Required properties: "ti,tmp175", "ti,tmp275", "ti,tmp75", + "ti,tmp75b", "ti,tmp75c", - reg: I2C bus address of the device diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt index 49ca5d83ed13..6ced829b0e58 100644 --- a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -7,7 +7,16 @@ Required properties: which correspond to thermal cooling states Optional properties: -- fan-supply : phandle to the regulator that provides power to the fan +- fan-supply : phandle to the regulator that provides power to the fan +- interrupts : This contains a single interrupt specifier which + describes the tachometer output of the fan as an + interrupt source. The output signal must generate a + defined number of interrupts per fan revolution, which + require that it must be self resetting edge interrupts. + See interrupt-controller/interrupts.txt for the format. +- pulses-per-revolution : define the tachometer pulses per fan revolution as + an integer (default is 2 interrupts per revolution). + The value must be greater than zero. Example: fan0: pwm-fan { @@ -38,3 +47,13 @@ Example: }; }; }; + +Example 2: + fan0: pwm-fan { + compatible = "pwm-fan"; + pwms = <&pwm 0 40000 0>; + fan-supply = <®_fan>; + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + pulses-per-revolution = <2>; + }; |