diff options
Diffstat (limited to 'Documentation/devicetree')
18 files changed, 340 insertions, 26 deletions
diff --git a/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt index 5626560a6cfd..8f52206cfd2a 100644 --- a/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt +++ b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt @@ -232,37 +232,152 @@ Example: }; }; -Stratix10 SoCFPGA ECC Manager +Stratix10 SoCFPGA ECC Manager (ARM64) The Stratix10 SoC ECC Manager handles the IRQs for each peripheral -in a shared register similar to the Arria10. However, ECC requires -access to registers that can only be read from Secure Monitor with -SMC calls. Therefore the device tree is slightly different. +in a shared register similar to the Arria10. However, Stratix10 ECC +requires access to registers that can only be read from Secure Monitor +with SMC calls. Therefore the device tree is slightly different. Note +that only 1 interrupt is sent in Stratix10 because the double bit errors +are treated as SErrors in ARM64 instead of IRQs in ARM32. Required Properties: - compatible : Should be "altr,socfpga-s10-ecc-manager" -- interrupts : Should be single bit error interrupt, then double bit error - interrupt. +- altr,sysgr-syscon : phandle to Stratix10 System Manager Block + containing the ECC manager registers. +- interrupts : Should be single bit error interrupt. - interrupt-controller : boolean indicator that ECC Manager is an interrupt controller - #interrupt-cells : must be set to 2. +- #address-cells: must be 1 +- #size-cells: must be 1 +- ranges : standard definition, should translate from local addresses Subcomponents: SDRAM ECC Required Properties: - compatible : Should be "altr,sdram-edac-s10" -- interrupts : Should be single bit error interrupt, then double bit error - interrupt, in this order. +- interrupts : Should be single bit error interrupt. + +On-Chip RAM ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-ocram-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent OCRAM node. +- interrupts : Should be single bit error interrupt. + +Ethernet FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-eth-mac-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent Ethernet node. +- interrupts : Should be single bit error interrupt. + +NAND FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-nand-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent NAND node. +- interrupts : Should be single bit error interrupt. + +DMA FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-dma-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent DMA node. +- interrupts : Should be single bit error interrupt. + +USB FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-usb-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent USB node. +- interrupts : Should be single bit error interrupt. + +SDMMC FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-s10-sdmmc-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent SD/MMC node. +- interrupts : Should be single bit error interrupt for port A + and then single bit error interrupt for port B. Example: eccmgr { compatible = "altr,socfpga-s10-ecc-manager"; - interrupts = <0 15 4>, <0 95 4>; + altr,sysmgr-syscon = <&sysmgr>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = <0 15 4>; interrupt-controller; #interrupt-cells = <2>; + ranges; sdramedac { compatible = "altr,sdram-edac-s10"; - interrupts = <16 4>, <48 4>; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH>; + }; + + ocram-ecc@ff8cc000 { + compatible = "altr,socfpga-s10-ocram-ecc"; + reg = <ff8cc000 0x100>; + altr,ecc-parent = <&ocram>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; + }; + + emac0-rx-ecc@ff8c0000 { + compatible = "altr,socfpga-s10-eth-mac-ecc"; + reg = <0xff8c0000 0x100>; + altr,ecc-parent = <&gmac0>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; + }; + + emac0-tx-ecc@ff8c0400 { + compatible = "altr,socfpga-s10-eth-mac-ecc"; + reg = <0xff8c0400 0x100>; + altr,ecc-parent = <&gmac0>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>' + }; + + nand-buf-ecc@ff8c8000 { + compatible = "altr,socfpga-s10-nand-ecc"; + reg = <0xff8c8000 0x100>; + altr,ecc-parent = <&nand>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + }; + + nand-rd-ecc@ff8c8400 { + compatible = "altr,socfpga-s10-nand-ecc"; + reg = <0xff8c8400 0x100>; + altr,ecc-parent = <&nand>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; + }; + + nand-wr-ecc@ff8c8800 { + compatible = "altr,socfpga-s10-nand-ecc"; + reg = <0xff8c8800 0x100>; + altr,ecc-parent = <&nand>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>; + }; + + dma-ecc@ff8c9000 { + compatible = "altr,socfpga-s10-dma-ecc"; + reg = <0xff8c9000 0x100>; + altr,ecc-parent = <&pdma>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; + + usb0-ecc@ff8c4000 { + compatible = "altr,socfpga-s10-usb-ecc"; + reg = <0xff8c4000 0x100>; + altr,ecc-parent = <&usb0>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + }; + + sdmmc-ecc@ff8c8c00 { + compatible = "altr,socfpga-s10-sdmmc-ecc"; + reg = <0xff8c8c00 0x100>; + altr,ecc-parent = <&mmc>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH>, + <15 IRQ_TYPE_LEVEL_HIGH>; }; }; diff --git a/Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt new file mode 100644 index 000000000000..ffb79ccf51ee --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt @@ -0,0 +1,26 @@ +Cirrus Logic Lochnagar Audio Development Board + +Lochnagar is an evaluation and development board for Cirrus Logic +Smart CODEC and Amp devices. It allows the connection of most Cirrus +Logic devices on mini-cards, as well as allowing connection of +various application processor systems to provide a full evaluation +platform. Audio system topology, clocking and power can all be +controlled through the Lochnagar, allowing the device under test +to be used in a variety of possible use cases. + +This binding document describes the binding for the hardware monitor +portion of the driver. + +This binding must be part of the Lochnagar MFD binding: + [4] ../mfd/cirrus,lochnagar.txt + +Required properties: + + - compatible : One of the following strings: + "cirrus,lochnagar2-hwmon" + +Example: + +lochnagar-hwmon { + compatible = "cirrus,lochnagar2-hwmon"; +}; diff --git a/Documentation/devicetree/bindings/hwmon/g762.txt b/Documentation/devicetree/bindings/hwmon/g762.txt index 25cc6d8ee575..6d154c4923de 100644 --- a/Documentation/devicetree/bindings/hwmon/g762.txt +++ b/Documentation/devicetree/bindings/hwmon/g762.txt @@ -21,7 +21,7 @@ If an optional property is not set in .dts file, then current value is kept unmodified (e.g. u-boot installed value). Additional information on operational parameters for the device is available -in Documentation/hwmon/g762. A detailed datasheet for the device is available +in Documentation/hwmon/g762.rst. A detailed datasheet for the device is available at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf. Example g762 node: diff --git a/Documentation/devicetree/bindings/hwmon/lm75.txt b/Documentation/devicetree/bindings/hwmon/lm75.txt index 12d8cf7cf592..586b5ed70be7 100644 --- a/Documentation/devicetree/bindings/hwmon/lm75.txt +++ b/Documentation/devicetree/bindings/hwmon/lm75.txt @@ -25,6 +25,7 @@ Required properties: "ti,tmp175", "ti,tmp275", "ti,tmp75", + "ti,tmp75b", "ti,tmp75c", - reg: I2C bus address of the device diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt index 49ca5d83ed13..6ced829b0e58 100644 --- a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -7,7 +7,16 @@ Required properties: which correspond to thermal cooling states Optional properties: -- fan-supply : phandle to the regulator that provides power to the fan +- fan-supply : phandle to the regulator that provides power to the fan +- interrupts : This contains a single interrupt specifier which + describes the tachometer output of the fan as an + interrupt source. The output signal must generate a + defined number of interrupts per fan revolution, which + require that it must be self resetting edge interrupts. + See interrupt-controller/interrupts.txt for the format. +- pulses-per-revolution : define the tachometer pulses per fan revolution as + an integer (default is 2 interrupts per revolution). + The value must be greater than zero. Example: fan0: pwm-fan { @@ -38,3 +47,13 @@ Example: }; }; }; + +Example 2: + fan0: pwm-fan { + compatible = "pwm-fan"; + pwms = <&pwm 0 40000 0>; + fan-supply = <®_fan>; + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + pulses-per-revolution = <2>; + }; diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt index 24c5cdaba8d2..ca83dcc84fb8 100644 --- a/Documentation/devicetree/bindings/net/davinci_emac.txt +++ b/Documentation/devicetree/bindings/net/davinci_emac.txt @@ -20,6 +20,8 @@ Required properties: Optional properties: - phy-handle: See ethernet.txt file in the same directory. If absent, davinci_emac driver defaults to 100/FULL. +- nvmem-cells: phandle, reference to an nvmem node for the MAC address +- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used - ti,davinci-rmii-en: 1 byte, 1 means use RMII - ti,davinci-no-bd-ram: boolean, does EMAC have BD RAM? diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index cfc376bc977a..a68621580584 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -10,15 +10,14 @@ Documentation/devicetree/bindings/phy/phy-bindings.txt. the boot program; should be used in cases where the MAC address assigned to the device by the boot program is different from the "local-mac-address" property; -- nvmem-cells: phandle, reference to an nvmem node for the MAC address; -- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used; - max-speed: number, specifies maximum speed in Mbit/s supported by the device; - max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than the maximum frame size (there's contradiction in the Devicetree Specification). - phy-mode: string, operation mode of the PHY interface. This is now a de-facto standard property; supported values are: - * "internal" + * "internal" (Internal means there is not a standard bus between the MAC and + the PHY, something proprietary is being used to embed the PHY in the MAC.) * "mii" * "gmii" * "sgmii" diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 174f292d8a3e..8b80515729d7 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -26,6 +26,10 @@ Required properties: Optional elements: 'tsu_clk' - clocks: Phandles to input clocks. +Optional properties: +- nvmem-cells: phandle, reference to an nvmem node for the MAC address +- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used + Optional properties for PHY child node: - reset-gpios : Should specify the gpio for phy reset - magic-packet : If present, indicates that the hardware supports waking diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt index 1f496159e2bb..dd25e73b5d79 100644 --- a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt @@ -4,16 +4,30 @@ Required properties: - compatible : Must be "regulator-gpio". - regulator-name : Defined in regulator.txt as optional, but required here. -- states : Selection of available voltages and GPIO configs. - if there are no states, then use a fixed regulator +- gpios : Array of one or more GPIO pins used to select the + regulator voltage/current listed in "states". +- states : Selection of available voltages/currents provided by + this regulator and matching GPIO configurations to + achieve them. If there are no states in the "states" + array, use a fixed regulator instead. Optional properties: -- enable-gpio : GPIO to use to enable/disable the regulator. -- gpios : GPIO group used to control voltage. -- gpios-states : gpios pin's initial states array. 0: LOW, 1: HIGH. - defualt is LOW if nothing is specified. +- enable-gpios : GPIO used to enable/disable the regulator. + Warning, the GPIO phandle flags are ignored and the + GPIO polarity is controlled solely by the presence + of "enable-active-high" DT property. This is due to + compatibility with old DTs. +- enable-active-high : Polarity of "enable-gpio" GPIO is active HIGH. + Default is active LOW. +- gpios-states : On operating systems, that don't support reading back + gpio values in output mode (most notably linux), this + array provides the state of GPIO pins set when + requesting them from the gpio controller. Systems, + that are capable of preserving state when requesting + the lines, are free to ignore this property. + 0: LOW, 1: HIGH. Default is LOW if nothing else + is specified. - startup-delay-us : Startup time in microseconds. -- enable-active-high : Polarity of GPIO is active high (default is low). - regulator-type : Specifies what is being regulated, must be either "voltage" or "current", defaults to voltage. @@ -30,7 +44,7 @@ Example: regulator-max-microvolt = <2600000>; regulator-boot-on; - enable-gpio = <&gpio0 23 0x4>; + enable-gpios = <&gpio0 23 0x4>; gpios = <&gpio0 24 0x4 &gpio0 25 0x4>; states = <1800000 0x3 diff --git a/Documentation/devicetree/bindings/regulator/st,stm32mp1-pwr-reg.txt b/Documentation/devicetree/bindings/regulator/st,stm32mp1-pwr-reg.txt new file mode 100644 index 000000000000..e372dd3f0c8a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/st,stm32mp1-pwr-reg.txt @@ -0,0 +1,43 @@ +STM32MP1 PWR Regulators +----------------------- + +Available Regulators in STM32MP1 PWR block are: + - reg11 for regulator 1V1 + - reg18 for regulator 1V8 + - usb33 for the swtich USB3V3 + +Required properties: +- compatible: Must be "st,stm32mp1,pwr-reg" +- list of child nodes that specify the regulator reg11, reg18 or usb33 + initialization data for defined regulators. The definition for each of + these nodes is defined using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. +- vdd-supply: phandle to the parent supply/regulator node for vdd input +- vdd_3v3_usbfs-supply: phandle to the parent supply/regulator node for usb33 + +Example: + +pwr_regulators: pwr@50001000 { + compatible = "st,stm32mp1,pwr-reg"; + reg = <0x50001000 0x10>; + vdd-supply = <&vdd>; + vdd_3v3_usbfs-supply = <&vdd_usb>; + + reg11: reg11 { + regulator-name = "reg11"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + reg18: reg18 { + regulator-name = "reg18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + usb33: usb33 { + regulator-name = "usb33"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt index 8854004a1d3a..411375eac54d 100644 --- a/Documentation/devicetree/bindings/spi/fsl-spi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -18,6 +18,10 @@ Optional properties: - gpios : specifies the gpio pins to be used for chipselects. The gpios will be referred to as reg = <index> in the SPI child nodes. If unspecified, a single SPI device without a chip select can be used. +- fsl,spisel_boot : for the MPC8306 and MPC8309, specifies that the + SPISEL_BOOT signal is used as chip select for a slave device. Use + reg = <number of gpios> in the corresponding child node, i.e. 0 if + the gpios property is not present. Example: spi@4c0 { diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt index 9ba7c5a273b4..db8e0d71c5bc 100644 --- a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt @@ -23,6 +23,18 @@ Required properties: Recommended properties: - spi-max-frequency: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt +Optional properties: +- nvidia,tx-clk-tap-delay: Delays the clock going out to the external device + with this tap value. This property is used to tune the outgoing data from + Tegra SPI master with respect to outgoing Tegra SPI master clock. + Tap values vary based on the platform design trace lengths from Tegra SPI + to corresponding slave devices. Valid tap values are from 0 thru 63. +- nvidia,rx-clk-tap-delay: Delays the clock coming in from the external device + with this tap value. This property is used to adjust the Tegra SPI master + clock with respect to the data from the SPI slave device. + Tap values vary based on the platform design trace lengths from Tegra SPI + to corresponding slave devices. Valid tap values are from 0 thru 63. + Example: spi@7000d600 { @@ -38,4 +50,12 @@ spi@7000d600 { reset-names = "spi"; dmas = <&apbdma 16>, <&apbdma 16>; dma-names = "rx", "tx"; + <spi-client>@<bus_num> { + ... + ... + nvidia,rx-clk-tap-delay = <0>; + nvidia,tx-clk-tap-delay = <16>; + ... + }; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index 37cf69586d10..18e14ee257b2 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -4,6 +4,7 @@ Required properties: - compatible : "renesas,msiof-r8a7743" (RZ/G1M) "renesas,msiof-r8a7744" (RZ/G1N) "renesas,msiof-r8a7745" (RZ/G1E) + "renesas,msiof-r8a77470" (RZ/G1C) "renesas,msiof-r8a774a1" (RZ/G2M) "renesas,msiof-r8a774c0" (RZ/G2E) "renesas,msiof-r8a7790" (R-Car H2) diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt index 2864bc6b659c..f54c8c36395e 100644 --- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt @@ -8,9 +8,16 @@ Required properties: - interrupts : One interrupt, used by the controller. - #address-cells : <1>, as required by generic SPI binding. - #size-cells : <0>, also as required by generic SPI binding. +- clocks : phandles for the clocks, see the description of clock-names below. + The phandle for the "ssi_clk" is required. The phandle for the "pclk" clock + is optional. If a single clock is specified but no clock-name, it is the + "ssi_clk" clock. If both clocks are listed, the "ssi_clk" must be first. Optional properties: -- cs-gpios : Specifies the gpio pis to be used for chipselects. +- clock-names : Contains the names of the clocks: + "ssi_clk", for the core clock used to generate the external SPI clock. + "pclk", the interface clock, required for register access. +- cs-gpios : Specifies the gpio pins to be used for chipselects. - num-cs : The number of chipselects. If omitted, this will default to 4. - reg-io-width : The I/O register width (in bytes) implemented by this device. Supported values are 2 or 4 (the default). @@ -25,6 +32,7 @@ Example: interrupts = <0 154 4>; #address-cells = <1>; #size-cells = <0>; + clocks = <&spi_m_clk>; num-cs = <2>; cs-gpios = <&gpio0 13 0>, <&gpio0 14 0>; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt index 6cc3c6fe25a3..e71b81a41ac0 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt @@ -7,7 +7,11 @@ Required properties: - reg : address and length of the lpspi master registers - interrupt-parent : core interrupt controller - interrupts : lpspi interrupt -- clocks : lpspi clock specifier +- clocks : lpspi clock specifier. Its number and order need to correspond to the + value in clock-names. +- clock-names : Corresponding to per clock and ipg clock in "clocks" + respectively. In i.MX7ULP, it only has per clk, so use CLK_DUMMY + to fill the "ipg" blank. - spi-slave : spi slave mode support. In slave mode, add this attribute without value. In master mode, remove it. @@ -18,6 +22,8 @@ lpspi2: lpspi@40290000 { reg = <0x40290000 0x10000>; interrupt-parent = <&intc>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clks IMX7ULP_CLK_LPSPI2>; + clocks = <&clks IMX7ULP_CLK_LPSPI2>, + <&clks IMX7ULP_CLK_DUMMY>; + clock-names = "per", "ipg"; spi-slave; }; diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index 69c356767cf8..c0f6c8ecfa2e 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -10,6 +10,7 @@ Required properties: - mediatek,mt8135-spi: for mt8135 platforms - mediatek,mt8173-spi: for mt8173 platforms - mediatek,mt8183-spi: for mt8183 platforms + - "mediatek,mt8516-spi", "mediatek,mt2712-spi": for mt8516 platforms - #address-cells: should be 1. diff --git a/Documentation/devicetree/bindings/spi/spi-mt7621.txt b/Documentation/devicetree/bindings/spi/spi-mt7621.txt new file mode 100644 index 000000000000..d5baec0fa56e --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-mt7621.txt @@ -0,0 +1,26 @@ +Binding for MTK SPI controller (MT7621 MIPS) + +Required properties: +- compatible: Should be one of the following: + - "ralink,mt7621-spi": for mt7621/mt7628/mt7688 platforms +- #address-cells: should be 1. +- #size-cells: should be 0. +- reg: Address and length of the register set for the device +- resets: phandle to the reset controller asserting this device in + reset + See ../reset/reset.txt for details. + +Optional properties: +- cs-gpios: see spi-bus.txt. + +Example: + +- SoC Specific Portion: +spi0: spi@b00 { + compatible = "ralink,mt7621-spi"; + reg = <0xb00 0x100>; + #address-cells = <1>; + #size-cells = <0>; + resets = <&rstctrl 18>; + reset-names = "spi"; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt b/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt new file mode 100644 index 000000000000..16b734ad3102 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt @@ -0,0 +1,25 @@ +Xilinx Zynq QSPI controller Device Tree Bindings +------------------------------------------------------------------- + +Required properties: +- compatible : Should be "xlnx,zynq-qspi-1.0". +- reg : Physical base address and size of QSPI registers map. +- interrupts : Property with a value describing the interrupt + number. +- clock-names : List of input clock names - "ref_clk", "pclk" + (See clock bindings for details). +- clocks : Clock phandles (see clock bindings for details). + +Optional properties: +- num-cs : Number of chip selects used. + +Example: + qspi: spi@e000d000 { + compatible = "xlnx,zynq-qspi-1.0"; + reg = <0xe000d000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <0 19 4>; + clock-names = "ref_clk", "pclk"; + clocks = <&clkc 10>, <&clkc 43>; + num-cs = <1>; + }; |