summaryrefslogtreecommitdiffstats
path: root/Documentation/arm/Sharp-LH/VectoredInterruptController
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/arm/Sharp-LH/VectoredInterruptController')
-rw-r--r--Documentation/arm/Sharp-LH/VectoredInterruptController80
1 files changed, 0 insertions, 80 deletions
diff --git a/Documentation/arm/Sharp-LH/VectoredInterruptController b/Documentation/arm/Sharp-LH/VectoredInterruptController
deleted file mode 100644
index 23047e9861ee..000000000000
--- a/Documentation/arm/Sharp-LH/VectoredInterruptController
+++ /dev/null
@@ -1,80 +0,0 @@
-README on the Vectored Interrupt Controller of the LH7A404
-==========================================================
-
-The 404 revision of the LH7A40X series comes with two vectored
-interrupts controllers. While the kernel does use some of the
-features of these devices, it is far from the purpose for which they
-were designed.
-
-When this README was written, the implementation of the VICs was in
-flux. It is possible that some details, especially with priorities,
-will change.
-
-The VIC support code is inspired by routines written by Sharp.
-
-
-Priority Control
-----------------
-
-The significant reason for using the VIC's vectoring is to control
-interrupt priorities. There are two tables in
-arch/arm/mach-lh7a40x/irq-lh7a404.c that look something like this.
-
- static unsigned char irq_pri_vic1[] = { IRQ_GPIO3INTR, };
- static unsigned char irq_pri_vic2[] = {
- IRQ_T3UI, IRQ_GPIO7INTR,
- IRQ_UART1INTR, IRQ_UART2INTR, IRQ_UART3INTR, };
-
-The initialization code reads these tables and inserts a vector
-address and enable for each indicated IRQ. Vectored interrupts have
-higher priority than non-vectored interrupts. So, on VIC1,
-IRQ_GPIO3INTR will be served before any other non-FIQ interrupt. Due
-to the way that the vectoring works, IRQ_T3UI is the next highest
-priority followed by the other vectored interrupts on VIC2. After
-that, the non-vectored interrupts are scanned in VIC1 then in VIC2.
-
-
-ISR
----
-
-The interrupt service routine macro get_irqnr() in
-arch/arm/kernel/entry-armv.S scans the VICs for the next active
-interrupt. The vectoring makes this code somewhat larger than it was
-before using vectoring (refer to the LH7A400 implementation). In the
-case where an interrupt is vectored, the implementation will tend to
-be faster than the non-vectored version. However, the worst-case path
-is longer.
-
-It is worth noting that at present, there is no need to read
-VIC2_VECTADDR because the register appears to be shared between the
-controllers. The code is written such that if this changes, it ought
-to still work properly.
-
-
-Vector Addresses
-----------------
-
-The proper use of the vectoring hardware would jump to the ISR
-specified by the vectoring address. Linux isn't structured to take
-advantage of this feature, though it might be possible to change
-things to support it.
-
-In this implementation, the vectoring address is used to speed the
-search for the active IRQ. The address is coded such that the lowest
-6 bits store the IRQ number for vectored interrupts. These numbers
-correspond to the bits in the interrupt status registers. IRQ zero is
-the lowest interrupt bit in VIC1. IRQ 32 is the lowest interrupt bit
-in VIC2. Because zero is a valid IRQ number and because we cannot
-detect whether or not there is a valid vectoring address if that
-address is zero, the eigth bit (0x100) is set for vectored interrupts.
-The address for IRQ 0x18 (VIC2) is 0x118. Only the ninth bit is set
-for the default handler on VIC1 and only the tenth bit is set for the
-default handler on VIC2.
-
-In other words.
-
- 0x000 - no active interrupt
- 0x1ii - vectored interrupt 0xii
- 0x2xx - unvectored interrupt on VIC1 (xx is don't care)
- 0x4xx - unvectored interrupt on VIC2 (xx is don't care)
-