diff options
62 files changed, 1956 insertions, 1102 deletions
diff --git a/arch/sh/Kconfig.debug b/arch/sh/Kconfig.debug index 55907af1dc25..12fec72fec5f 100644 --- a/arch/sh/Kconfig.debug +++ b/arch/sh/Kconfig.debug @@ -19,50 +19,6 @@ config SH_STANDARD_BIOS mask ROM and no flash (WindowsCE machines fall in this category). If unsure, say N. -config EARLY_SCIF_CONSOLE - bool "Use early SCIF console" - help - This enables an early console using a fixed SCIF port. This can - be used by platforms that are either not running the SH - standard BIOS, or do not wish to use the BIOS callbacks for the - serial I/O. - -config EARLY_SCIF_CONSOLE_PORT - hex - depends on EARLY_SCIF_CONSOLE - default "0xa4400000" if CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7705 - default "0xa4430000" if CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721 - default "0xf8420000" if CPU_SUBTYPE_SH7619 - default "0xff804000" if CPU_SUBTYPE_MXG - default "0xffc30000" if CPU_SUBTYPE_SHX3 - default "0xffe00000" if CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7763 || \ - CPU_SUBTYPE_SH7722 || CPU_SUBTYPE_SH7366 || \ - CPU_SUBTYPE_SH7343 - default "0xfe4c0000" if CPU_SUBTYPE_SH7757 - default "0xffeb0000" if CPU_SUBTYPE_SH7785 - default "0xffeb0000" if CPU_SUBTYPE_SH7786 - default "0xfffe8000" if CPU_SUBTYPE_SH7203 - default "0xfffe9800" if CPU_SUBTYPE_SH7206 || CPU_SUBTYPE_SH7263 - default "0xffe80000" if CPU_SH4 - default "0xa4000150" if CPU_SH3 - default "0x00000000" - -config EARLY_PRINTK - bool "Early printk support" - depends on SH_STANDARD_BIOS || EARLY_SCIF_CONSOLE - help - Say Y here to redirect kernel printk messages to the serial port - used by the SH-IPL bootloader, starting very early in the boot - process and ending when the kernel's serial console is initialised. - This option is only useful porting the kernel to a new machine, - when the kernel may crash or hang before the serial console is - initialised. If unsure, say N. - - On devices that are running SH-IPL and want to keep the port - initialization consistent while not using the BIOS callbacks, - select both the EARLY_SCIF_CONSOLE and SH_STANDARD_BIOS, using - the kernel command line option to toggle back and forth. - config STACK_DEBUG bool "Check for stack overflows" depends on DEBUG_KERNEL && SUPERH32 diff --git a/arch/sh/boards/mach-ap325rxa/setup.c b/arch/sh/boards/mach-ap325rxa/setup.c index 7a9f69663f1a..1f5fa5c44f6d 100644 --- a/arch/sh/boards/mach-ap325rxa/setup.c +++ b/arch/sh/boards/mach-ap325rxa/setup.c @@ -323,7 +323,8 @@ static struct soc_camera_platform_info camera_info = { .height = 480, }, .bus_param = SOCAM_PCLK_SAMPLE_RISING | SOCAM_HSYNC_ACTIVE_HIGH | - SOCAM_VSYNC_ACTIVE_HIGH | SOCAM_MASTER | SOCAM_DATAWIDTH_8, + SOCAM_VSYNC_ACTIVE_HIGH | SOCAM_MASTER | SOCAM_DATAWIDTH_8 | + SOCAM_DATA_ACTIVE_HIGH, .set_capture = camera_set_capture, }; diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c index 826e62326d51..194aaca22d47 100644 --- a/arch/sh/boards/mach-ecovec24/setup.c +++ b/arch/sh/boards/mach-ecovec24/setup.c @@ -19,11 +19,18 @@ #include <linux/usb/r8a66597.h> #include <linux/i2c.h> #include <linux/i2c/tsc2007.h> +#include <linux/spi/spi.h> +#include <linux/spi/sh_msiof.h> +#include <linux/spi/mmc_spi.h> +#include <linux/mmc/host.h> #include <linux/input.h> #include <linux/input/sh_keysc.h> #include <linux/mfd/sh_mobile_sdhi.h> #include <video/sh_mobile_lcdc.h> +#include <sound/sh_fsi.h> #include <media/sh_mobile_ceu.h> +#include <media/tw9910.h> +#include <media/mt9t112.h> #include <asm/heartbeat.h> #include <asm/sh_eth.h> #include <asm/clock.h> @@ -338,6 +345,12 @@ static struct platform_device ceu1_device = { }; /* I2C device */ +static struct i2c_board_info i2c0_devices[] = { + { + I2C_BOARD_INFO("da7210", 0x1a), + }, +}; + static struct i2c_board_info i2c1_devices[] = { { I2C_BOARD_INFO("r2025sd", 0x32), @@ -421,6 +434,7 @@ static struct i2c_board_info ts_i2c_clients = { .irq = IRQ0, }; +#ifdef CONFIG_MFD_SH_MOBILE_SDHI /* SHDI0 */ static void sdhi0_set_pwr(struct platform_device *pdev, int state) { @@ -493,6 +507,248 @@ static struct platform_device sdhi1_device = { }, }; +#else + +static int mmc_spi_get_ro(struct device *dev) +{ + return gpio_get_value(GPIO_PTY6); +} + +static int mmc_spi_get_cd(struct device *dev) +{ + return !gpio_get_value(GPIO_PTY7); +} + +static void mmc_spi_setpower(struct device *dev, unsigned int maskval) +{ + gpio_set_value(GPIO_PTB6, maskval ? 1 : 0); +} + +static struct mmc_spi_platform_data mmc_spi_info = { + .get_ro = mmc_spi_get_ro, + .get_cd = mmc_spi_get_cd, + .caps = MMC_CAP_NEEDS_POLL, + .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* 3.3V only */ + .setpower = mmc_spi_setpower, +}; + +static struct spi_board_info spi_bus[] = { + { + .modalias = "mmc_spi", + .platform_data = &mmc_spi_info, + .max_speed_hz = 5000000, + .mode = SPI_MODE_0, + .controller_data = (void *) GPIO_PTM4, + }, +}; + +static struct sh_msiof_spi_info msiof0_data = { + .num_chipselect = 1, +}; + +static struct resource msiof0_resources[] = { + [0] = { + .name = "MSIOF0", + .start = 0xa4c40000, + .end = 0xa4c40063, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = 84, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device msiof0_device = { + .name = "spi_sh_msiof", + .id = 0, /* MSIOF0 */ + .dev = { + .platform_data = &msiof0_data, + }, + .num_resources = ARRAY_SIZE(msiof0_resources), + .resource = msiof0_resources, + .archdata = { + .hwblk_id = HWBLK_MSIOF0, + }, +}; + +#endif + +/* I2C Video/Camera */ +static struct i2c_board_info i2c_camera[] = { + { + I2C_BOARD_INFO("tw9910", 0x45), + }, + { + /* 1st camera */ + I2C_BOARD_INFO("mt9t112", 0x3c), + }, + { + /* 2nd camera */ + I2C_BOARD_INFO("mt9t112", 0x3c), + }, +}; + +/* tw9910 */ +static int tw9910_power(struct device *dev, int mode) +{ + int val = mode ? 0 : 1; + + gpio_set_value(GPIO_PTU2, val); + if (mode) + mdelay(100); + + return 0; +} + +static struct tw9910_video_info tw9910_info = { + .buswidth = SOCAM_DATAWIDTH_8, + .mpout = TW9910_MPO_FIELD, +}; + +static struct soc_camera_link tw9910_link = { + .i2c_adapter_id = 0, + .bus_id = 1, + .power = tw9910_power, + .board_info = &i2c_camera[0], + .module_name = "tw9910", + .priv = &tw9910_info, +}; + +/* mt9t112 */ +static int mt9t112_power1(struct device *dev, int mode) +{ + gpio_set_value(GPIO_PTA3, mode); + if (mode) + mdelay(100); + + return 0; +} + +static struct mt9t112_camera_info mt9t112_info1 = { + .flags = MT9T112_FLAG_PCLK_RISING_EDGE | MT9T112_FLAG_DATAWIDTH_8, + .divider = { 0x49, 0x6, 0, 6, 0, 9, 9, 6, 0 }, /* for 24MHz */ +}; + +static struct soc_camera_link mt9t112_link1 = { + .i2c_adapter_id = 0, + .power = mt9t112_power1, + .bus_id = 0, + .board_info = &i2c_camera[1], + .module_name = "mt9t112", + .priv = &mt9t112_info1, +}; + +static int mt9t112_power2(struct device *dev, int mode) +{ + gpio_set_value(GPIO_PTA4, mode); + if (mode) + mdelay(100); + + return 0; +} + +static struct mt9t112_camera_info mt9t112_info2 = { + .flags = MT9T112_FLAG_PCLK_RISING_EDGE | MT9T112_FLAG_DATAWIDTH_8, + .divider = { 0x49, 0x6, 0, 6, 0, 9, 9, 6, 0 }, /* for 24MHz */ +}; + +static struct soc_camera_link mt9t112_link2 = { + .i2c_adapter_id = 1, + .power = mt9t112_power2, + .bus_id = 1, + .board_info = &i2c_camera[2], + .module_name = "mt9t112", + .priv = &mt9t112_info2, +}; + +static struct platform_device camera_devices[] = { + { + .name = "soc-camera-pdrv", + .id = 0, + .dev = { + .platform_data = &tw9910_link, + }, + }, + { + .name = "soc-camera-pdrv", + .id = 1, + .dev = { + .platform_data = &mt9t112_link1, + }, + }, + { + .name = "soc-camera-pdrv", + .id = 2, + .dev = { + .platform_data = &mt9t112_link2, + }, + }, +}; + +/* FSI */ +/* + * FSI-B use external clock which came from da7210. + * So, we should change parent of fsi + */ +#define FCLKBCR 0xa415000c +static void fsimck_init(struct clk *clk) +{ + u32 status = ctrl_inl(clk->enable_reg); + + /* use external clock */ + status &= ~0x000000ff; + status |= 0x00000080; + + ctrl_outl(status, clk->enable_reg); +} + +static struct clk_ops fsimck_clk_ops = { + .init = fsimck_init, +}; + +static struct clk fsimckb_clk = { + .name = "fsimckb_clk", + .id = -1, + .ops = &fsimck_clk_ops, + .enable_reg = (void __iomem *)FCLKBCR, + .rate = 0, /* unknown */ +}; + +struct sh_fsi_platform_info fsi_info = { + .portb_flags = SH_FSI_BRS_INV | + SH_FSI_OUT_SLAVE_MODE | + SH_FSI_IN_SLAVE_MODE | + SH_FSI_OFMT(I2S) | + SH_FSI_IFMT(I2S), +}; + +static struct resource fsi_resources[] = { + [0] = { + .name = "FSI", + .start = 0xFE3C0000, + .end = 0xFE3C021d, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = 108, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device fsi_device = { + .name = "sh_fsi", + .id = 0, + .num_resources = ARRAY_SIZE(fsi_resources), + .resource = fsi_resources, + .dev = { + .platform_data = &fsi_info, + }, + .archdata = { + .hwblk_id = HWBLK_SPU, /* FSI needs SPU hwblk */ + }, +}; + static struct platform_device *ecovec_devices[] __initdata = { &heartbeat_device, &nor_flash_device, @@ -503,8 +759,16 @@ static struct platform_device *ecovec_devices[] __initdata = { &ceu0_device, &ceu1_device, &keysc_device, +#ifdef CONFIG_MFD_SH_MOBILE_SDHI &sdhi0_device, &sdhi1_device, +#else + &msiof0_device, +#endif + &camera_devices[0], + &camera_devices[1], + &camera_devices[2], + &fsi_device, }; #define EEPROM_ADDR 0x50 @@ -560,6 +824,8 @@ extern char ecovec24_sdram_leave_end; static int __init arch_setup(void) { + struct clk *clk; + /* register board specific self-refresh code */ sh_mobile_register_self_refresh(SUSP_SH_STANDBY | SUSP_SH_SF, &ecovec24_sdram_enter_start, @@ -773,7 +1039,8 @@ static int __init arch_setup(void) gpio_direction_input(GPIO_PTR5); gpio_direction_input(GPIO_PTR6); - /* enable SDHI0 (needs DS2.4 set to ON) */ +#ifdef CONFIG_MFD_SH_MOBILE_SDHI + /* enable SDHI0 on CN11 (needs DS2.4 set to ON) */ gpio_request(GPIO_FN_SDHI0CD, NULL); gpio_request(GPIO_FN_SDHI0WP, NULL); gpio_request(GPIO_FN_SDHI0CMD, NULL); @@ -785,7 +1052,7 @@ static int __init arch_setup(void) gpio_request(GPIO_PTB6, NULL); gpio_direction_output(GPIO_PTB6, 0); - /* enable SDHI1 (needs DS2.6,7 set to ON,OFF) */ + /* enable SDHI1 on CN12 (needs DS2.6,7 set to ON,OFF) */ gpio_request(GPIO_FN_SDHI1CD, NULL); gpio_request(GPIO_FN_SDHI1WP, NULL); gpio_request(GPIO_FN_SDHI1CMD, NULL); @@ -799,8 +1066,59 @@ static int __init arch_setup(void) /* I/O buffer drive ability is high for SDHI1 */ ctrl_outw((ctrl_inw(IODRIVEA) & ~0x3000) | 0x2000 , IODRIVEA); +#else + /* enable MSIOF0 on CN11 (needs DS2.4 set to OFF) */ + gpio_request(GPIO_FN_MSIOF0_TXD, NULL); + gpio_request(GPIO_FN_MSIOF0_RXD, NULL); + gpio_request(GPIO_FN_MSIOF0_TSCK, NULL); + gpio_request(GPIO_PTM4, NULL); /* software CS control of TSYNC pin */ + gpio_direction_output(GPIO_PTM4, 1); /* active low CS */ + gpio_request(GPIO_PTB6, NULL); /* 3.3V power control */ + gpio_direction_output(GPIO_PTB6, 0); /* disable power by default */ + gpio_request(GPIO_PTY6, NULL); /* write protect */ + gpio_direction_input(GPIO_PTY6); + gpio_request(GPIO_PTY7, NULL); /* card detect */ + gpio_direction_input(GPIO_PTY7); + + spi_register_board_info(spi_bus, ARRAY_SIZE(spi_bus)); +#endif + + /* enable Video */ + gpio_request(GPIO_PTU2, NULL); + gpio_direction_output(GPIO_PTU2, 1); + + /* enable Camera */ + gpio_request(GPIO_PTA3, NULL); + gpio_request(GPIO_PTA4, NULL); + gpio_direction_output(GPIO_PTA3, 0); + gpio_direction_output(GPIO_PTA4, 0); + + /* enable FSI */ + gpio_request(GPIO_FN_FSIMCKB, NULL); + gpio_request(GPIO_FN_FSIIBSD, NULL); + gpio_request(GPIO_FN_FSIOBSD, NULL); + gpio_request(GPIO_FN_FSIIBBCK, NULL); + gpio_request(GPIO_FN_FSIIBLRCK, NULL); + gpio_request(GPIO_FN_FSIOBBCK, NULL); + gpio_request(GPIO_FN_FSIOBLRCK, NULL); + gpio_request(GPIO_FN_CLKAUDIOBO, NULL); + + /* change parent of FSI B */ + clk = clk_get(NULL, "fsib_clk"); + clk_register(&fsimckb_clk); + clk_set_parent(clk, &fsimckb_clk); + clk_set_rate(clk, 11000); + clk_set_rate(&fsimckb_clk, 11000); + clk_put(clk); + + gpio_request(GPIO_PTU0, NULL); + gpio_direction_output(GPIO_PTU0, 0); + mdelay(20); /* enable I2C device */ + i2c_register_board_info(0, i2c0_devices, + ARRAY_SIZE(i2c0_devices)); + i2c_register_board_info(1, i2c1_devices, ARRAY_SIZE(i2c1_devices)); diff --git a/arch/sh/boards/mach-kfr2r09/lcd_wqvga.c b/arch/sh/boards/mach-kfr2r09/lcd_wqvga.c index 8ccb1cc8b589..e9b970846c41 100644 --- a/arch/sh/boards/mach-kfr2r09/lcd_wqvga.c +++ b/arch/sh/boards/mach-kfr2r09/lcd_wqvga.c @@ -273,6 +273,12 @@ int kfr2r09_lcd_setup(void *board_data, void *sohandle, return 0; } +void kfr2r09_lcd_start(void *board_data, void *sohandle, + struct sh_mobile_lcdc_sys_bus_ops *so) +{ + write_memory_start(sohandle, so); +} + #define CTRL_CKSW 0x10 #define CTRL_C10 0x20 #define CTRL_CPSW 0x80 diff --git a/arch/sh/boards/mach-kfr2r09/setup.c b/arch/sh/boards/mach-kfr2r09/setup.c index 9038d768a525..5d7b5d92475e 100644 --- a/arch/sh/boards/mach-kfr2r09/setup.c +++ b/arch/sh/boards/mach-kfr2r09/setup.c @@ -150,6 +150,7 @@ static struct sh_mobile_lcdc_info kfr2r09_sh_lcdc_info = { }, .board_cfg = { .setup_sys = kfr2r09_lcd_setup, + .start_transfer = kfr2r09_lcd_start, .display_on = kfr2r09_lcd_on, .display_off = kfr2r09_lcd_off, }, diff --git a/arch/sh/boards/mach-se/7722/irq.c b/arch/sh/boards/mach-se/7722/irq.c index 4eb31acfafef..b221b6842b0d 100644 --- a/arch/sh/boards/mach-se/7722/irq.c +++ b/arch/sh/boards/mach-se/7722/irq.c @@ -57,15 +57,16 @@ static void se7722_irq_demux(unsigned int irq, struct irq_desc *desc) */ void __init init_se7722_IRQ(void) { - int i; + int i, irq; ctrl_outw(0, IRQ01_MASK); /* disable all irqs */ ctrl_outw(0x2000, 0xb03fffec); /* mrshpc irq enable */ for (i = 0; i < SE7722_FPGA_IRQ_NR; i++) { - se7722_fpga_irq[i] = create_irq(); - if (se7722_fpga_irq[i] < 0) + irq = create_irq(); + if (irq < 0) return; + se7722_fpga_irq[i] = irq; set_irq_chip_and_handler_name(se7722_fpga_irq[i], &se7722_irq_chip, diff --git a/arch/sh/boards/mach-se/7724/setup.c b/arch/sh/boards/mach-se/7724/setup.c index 4b0f0c0dc2b8..5d0f70b46c97 100644 --- a/arch/sh/boards/mach-se/7724/setup.c +++ b/arch/sh/boards/mach-se/7724/setup.c @@ -514,6 +514,13 @@ static struct platform_device *ms7724se_devices[] __initdata = { &sdhi1_cn8_device, }; +/* I2C device */ +static struct i2c_board_info i2c0_devices[] = { + { + I2C_BOARD_INFO("ak4642", 0x12), + }, +}; + #define EEPROM_OP 0xBA206000 #define EEPROM_ADR 0xBA206004 #define EEPROM_DATA 0xBA20600C @@ -575,6 +582,16 @@ extern char ms7724se_sdram_enter_end; extern char ms7724se_sdram_leave_start; extern char ms7724se_sdram_leave_end; + +static int __init arch_setup(void) +{ + /* enable I2C device */ + i2c_register_board_info(0, i2c0_devices, + ARRAY_SIZE(i2c0_devices)); + return 0; +} +arch_initcall(arch_setup); + static int __init devices_setup(void) { u16 sw = ctrl_inw(SW4140); /* select camera, monitor */ diff --git a/arch/sh/configs/ecovec24-romimage_defconfig b/arch/sh/configs/ecovec24-romimage_defconfig index 0774924623cc..46874704e4e7 100644 --- a/arch/sh/configs/ecovec24-romimage_defconfig +++ b/arch/sh/configs/ecovec24-romimage_defconfig @@ -203,7 +203,7 @@ CONFIG_MMU=y CONFIG_PAGE_OFFSET=0x80000000 CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_MEMORY_START=0x08000000 -CONFIG_MEMORY_SIZE=0x08000000 +CONFIG_MEMORY_SIZE=0x10000000 CONFIG_29BIT=y # CONFIG_X2TLB is not set CONFIG_VSYSCALL=y diff --git a/arch/sh/configs/ecovec24_defconfig b/arch/sh/configs/ecovec24_defconfig index ac6469718a2c..cad918437ca7 100644 --- a/arch/sh/configs/ecovec24_defconfig +++ b/arch/sh/configs/ecovec24_defconfig @@ -204,7 +204,7 @@ CONFIG_MMU=y CONFIG_PAGE_OFFSET=0x80000000 CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_MEMORY_START=0x08000000 -CONFIG_MEMORY_SIZE=0x08000000 +CONFIG_MEMORY_SIZE=0x10000000 CONFIG_29BIT=y # CONFIG_X2TLB is not set CONFIG_VSYSCALL=y diff --git a/arch/sh/configs/rts7751r2d1_defconfig b/arch/sh/configs/rts7751r2d1_defconfig index f521e82cc19e..6f1126b3e487 100644 --- a/arch/sh/configs/rts7751r2d1_defconfig +++ b/arch/sh/configs/rts7751r2d1_defconfig @@ -324,7 +324,7 @@ CONFIG_ENTRY_OFFSET=0x00001000 # CONFIG_UBC_WAKEUP is not set CONFIG_CMDLINE_OVERWRITE=y # CONFIG_CMDLINE_EXTEND is not set -CONFIG_CMDLINE="console=tty0 console=ttySC0,115200 root=/dev/sda1 earlyprintk=serial" +CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 root=/dev/sda1" # |