diff options
-rw-r--r-- | drivers/net/phy/at803x.c | 78 |
1 files changed, 78 insertions, 0 deletions
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index 96c61aa75bd7..101651b2de54 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -21,6 +21,17 @@ #include <linux/regulator/consumer.h> #include <dt-bindings/net/qca-ar803x.h> +#define AT803X_SPECIFIC_FUNCTION_CONTROL 0x10 +#define AT803X_SFC_ASSERT_CRS BIT(11) +#define AT803X_SFC_FORCE_LINK BIT(10) +#define AT803X_SFC_MDI_CROSSOVER_MODE_M GENMASK(6, 5) +#define AT803X_SFC_AUTOMATIC_CROSSOVER 0x3 +#define AT803X_SFC_MANUAL_MDIX 0x1 +#define AT803X_SFC_MANUAL_MDI 0x0 +#define AT803X_SFC_SQE_TEST BIT(2) +#define AT803X_SFC_POLARITY_REVERSAL BIT(1) +#define AT803X_SFC_DISABLE_JABBER BIT(0) + #define AT803X_SPECIFIC_STATUS 0x11 #define AT803X_SS_SPEED_MASK (3 << 14) #define AT803X_SS_SPEED_1000 (2 << 14) @@ -703,6 +714,12 @@ static int at803x_read_status(struct phy_device *phydev) return ss; if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) { + int sfc; + + sfc = phy_read(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL); + if (sfc < 0) + return sfc; + switch (ss & AT803X_SS_SPEED_MASK) { case AT803X_SS_SPEED_10: phydev->speed = SPEED_10; @@ -718,10 +735,23 @@ static int at803x_read_status(struct phy_device *phydev) phydev->duplex = DUPLEX_FULL; else phydev->duplex = DUPLEX_HALF; + if (ss & AT803X_SS_MDIX) phydev->mdix = ETH_TP_MDI_X; else phydev->mdix = ETH_TP_MDI; + + switch (FIELD_GET(AT803X_SFC_MDI_CROSSOVER_MODE_M, sfc)) { + case AT803X_SFC_MANUAL_MDI: + phydev->mdix_ctrl = ETH_TP_MDI; + break; + case AT803X_SFC_MANUAL_MDIX: + phydev->mdix_ctrl = ETH_TP_MDI_X; + break; + case AT803X_SFC_AUTOMATIC_CROSSOVER: + phydev->mdix_ctrl = ETH_TP_MDI_AUTO; + break; + } } if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) @@ -730,6 +760,50 @@ static int at803x_read_status(struct phy_device *phydev) return 0; } +static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl) +{ + u16 val; + + switch (ctrl) { + case ETH_TP_MDI: + val = AT803X_SFC_MANUAL_MDI; + break; + case ETH_TP_MDI_X: + val = AT803X_SFC_MANUAL_MDIX; + break; + case ETH_TP_MDI_AUTO: + val = AT803X_SFC_AUTOMATIC_CROSSOVER; + break; + default: + return 0; + } + + return phy_modify_changed(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL, + AT803X_SFC_MDI_CROSSOVER_MODE_M, + FIELD_PREP(AT803X_SFC_MDI_CROSSOVER_MODE_M, val)); +} + +static int at803x_config_aneg(struct phy_device *phydev) +{ + int ret; + + ret = at803x_config_mdix(phydev, phydev->mdix_ctrl); + if (ret < 0) + return ret; + + /* Changes of the midx bits are disruptive to the normal operation; + * therefore any changes to these registers must be followed by a + * software reset to take effect. + */ + if (ret == 1) { + ret = genphy_soft_reset(phydev); + if (ret < 0) + return ret; + } + + return genphy_config_aneg(phydev); +} + static int at803x_get_downshift(struct phy_device *phydev, u8 *d) { int val; @@ -979,6 +1053,7 @@ static struct phy_driver at803x_driver[] = { .flags = PHY_POLL_CABLE_TEST, .probe = at803x_probe, .remove = at803x_remove, + .config_aneg = at803x_config_aneg, .config_init = at803x_config_init, .soft_reset = genphy_soft_reset, .set_wol = at803x_set_wol, @@ -1061,6 +1136,9 @@ static struct phy_driver at803x_driver[] = { .config_intr = &at803x_config_intr, .cable_test_start = at803x_cable_test_start, .cable_test_get_status = at803x_cable_test_get_status, + .read_status = at803x_read_status, + .soft_reset = genphy_soft_reset, + .config_aneg = at803x_config_aneg, } }; module_phy_driver(at803x_driver); |