diff options
43 files changed, 1140 insertions, 940 deletions
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 523341a0e113..8bc95e2fc47f 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -11,7 +11,6 @@ Required properties: - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt -- fsl,spi-num-chipselects : Contains the number of the chipselect - cs-gpios : Specifies the gpio pins to be used for chipselects. - clocks : Clock specifiers for both ipg and per clocks. - clock-names : Clock names should include both "ipg" and "per" @@ -21,6 +20,9 @@ See the clock consumer binding, Documentation/devicetree/bindings/dma/dma.txt - dma-names: DMA request names should include "tx" and "rx" if present. +Obsolete properties: +- fsl,spi-num-chipselects : Contains the number of the chipselect + Example: ecspi@70010000 { @@ -29,7 +31,6 @@ ecspi@70010000 { compatible = "fsl,imx51-ecspi"; reg = <0x70010000 0x4000>; interrupts = <36>; - fsl,spi-num-chipselects = <2>; cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */ <&gpio3 25 0>; /* GPIO3_25 */ dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 42d595425dfb..17822860cb98 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -8,11 +8,10 @@ in slave mode. The SPI master node requires the following properties: - #address-cells - number of cells required to define a chip select - address on the SPI bus. + address on the SPI bus. - #size-cells - should be zero. - compatible - name of SPI bus controller following generic names - recommended practice. -- cs-gpios - (optional) gpios chip select. + recommended practice. No other properties are required in the SPI bus node. It is assumed that a driver for an SPI bus device will understand that it is an SPI bus. However, the binding does not attempt to define the specific method for @@ -22,11 +21,12 @@ assumption that board specific platform code will be used to manage chip selects. Individual drivers can define additional properties to support describing the chip select layout. -Optional property: -- num-cs : total number of chipselects +Optional properties: +- cs-gpios - gpios chip select. +- num-cs - total number of chipselects. -If cs-gpios is used the number of chip select will automatically increased -with max(cs-gpios > hw cs) +If cs-gpios is used the number of chip selects will be increased automatically +with max(cs-gpios > hw cs). So if for example the controller has 2 CS lines, and the cs-gpios property looks like this: @@ -45,29 +45,30 @@ SPI slave nodes must be children of the SPI master node and can contain the following properties. - reg - (required) chip select address of device. - compatible - (required) name of SPI device following generic names - recommended practice -- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz + recommended practice. +- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz. - spi-cpol - (optional) Empty property indicating device requires - inverse clock polarity (CPOL) mode + inverse clock polarity (CPOL) mode. - spi-cpha - (optional) Empty property indicating device requires - shifted clock phase (CPHA) mode + shifted clock phase (CPHA) mode. - spi-cs-high - (optional) Empty property indicating device requires - chip select active high + chip select active high. - spi-3wire - (optional) Empty property indicating device requires - 3-wire mode. + 3-wire mode. - spi-lsb-first - (optional) Empty property indicating device requires LSB first mode. -- spi-tx-bus-width - (optional) The bus width(number of data wires) that +- spi-tx-bus-width - (optional) The bus width (number of data wires) that is used for MOSI. Defaults to 1 if not present. -- spi-rx-bus-width - (optional) The bus width(number of data wires) that +- spi-rx-bus-width - (optional) The bus width (number of data wires) that is used for MISO. Defaults to 1 if not present. - spi-rx-delay-us - (optional) Microsecond delay after a read transfer. - spi-tx-delay-us - (optional) Microsecond delay after a write transfer. Some SPI controllers and devices support Dual and Quad SPI transfer mode. -It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD). +It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4 +wires (QUAD). Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is -only 1(SINGLE), 2(DUAL) and 4(QUAD). +only 1 (SINGLE), 2 (DUAL) and 4 (QUAD). Dual/Quad mode is not allowed when 3-wire mode is used. If a gpio chipselect is used for the SPI slave the gpio number will be passed diff --git a/Documentation/devicetree/bindings/spi/spi-clps711x.txt b/Documentation/devicetree/bindings/spi/spi-clps711x.txt new file mode 100644 index 000000000000..4c3ec13f423f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-clps711x.txt @@ -0,0 +1,33 @@ +Serial Peripheral Interface on Cirrus Logic CL-PS71xx, EP72xx, EP73xx + +Required properties +- #address-cells: must be <1> +- #size-cells: must be <0> +- compatible: should include "cirrus,ep7209-spi" +- reg: Address and length of one register range +- interrupts: one interrupt line +- clocks: One entry, refers to the SPI bus clock +- cs-gpios: Specifies the gpio pins to be used for chipselects. + See: Documentation/devicetree/bindings/spi/spi-bus.txt + +An additional register is present in the system controller, +which is assumed to be in the same device tree, with and marked +as compatible with "cirrus,ep7209-syscon3". + +Example: + +spi@80000500 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "cirrus,ep7209-spi"; + reg = <0x80000500 0x4>; + interrupts = <15>; + clocks = <&clks CLPS711X_CLK_SPI>; + status = "disabled"; +}; + +syscon3: syscon@80002200 { + compatible = "cirrus,ep7209-syscon3", "syscon"; + reg = <0x80002200 0x40>; +}; + diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index d1e914adcf6e..f5916c92fe91 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -21,7 +21,7 @@ Required properties: IP to the interrupt controller within the SoC. Possible values are 0 and 1. Manual says one of the two possible interrupt lines can be tied to the interrupt controller. Set this - based on a specifc SoC configuration. + based on a specific SoC configuration. - interrupts: interrupt number mapped to CPU. - clocks: spi clk phandle diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index 98bc69815eb3..4f629cc7634a 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -8,7 +8,15 @@ Required properties: - "marvell,armada-380-spi", for the Armada 38x SoCs - "marvell,armada-390-spi", for the Armada 39x SoCs - "marvell,armada-xp-spi", for the Armada XP SoCs -- reg : offset and length of the register set for the device +- reg : offset and length of the register set for the device. + This property can optionally have additional entries to configure + the SPI direct access mode that some of the Marvell SoCs support + additionally to the normal indirect access (PIO) mode. The values + for the MBus "target" and "attribute" are defined in the Marvell + SoC "Functional Specifications" Manual in the chapter "Marvell + Core Processor Address Decoding". + The eight register sets following the control registers refer to + chip-select lines 0 through 7 respectively. - cell-index : Which of multiple SPI controllers is this. Optional properties: - interrupts : Is currently not used. @@ -23,3 +31,42 @@ Example: interrupts = <23>; status = "disabled"; }; + +Example with SPI direct mode support (optionally): + spi0: spi@10600 { + compatible = "marvell,orion-spi"; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x28>, /* control */ + <MBUS_ID(0x01, 0x1e) 0 0xffffffff>, /* CS0 */ + <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */ + <MBUS_ID(0x01, 0x9e) 0 0xffffffff>, /* CS2 */ + <MBUS_ID(0x01, 0xde) 0 0xffffffff>, /* CS3 */ + <MBUS_ID(0x01, 0x1f) 0 0xffffffff>, /* CS4 */ + <MBUS_ID(0x01, 0x5f) 0 0xffffffff>, /* CS5 */ + <MBUS_ID(0x01, 0x9f) 0 0xffffffff>, /* CS6 */ + <MBUS_ID(0x01, 0xdf) 0 0xffffffff>; /* CS7 */ + interrupts = <23>; + status = "disabled"; + }; + +To enable the direct mode, the board specific 'ranges' property in the +'soc' node needs to add the entries for the desired SPI controllers +and its chip-selects that are used in the direct mode instead of PIO +mode. Here an example for this (SPI controller 0, device 1 and SPI +controller 1, device 2 are used in direct mode. All other SPI device +are used in the default indirect (PIO) mode): + soc { + /* + * Enable the SPI direct access by configuring an entry + * here in the board-specific ranges property + */ + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000>, /* internal regs */ + <MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>, /* BootROM */ + <MBUS_ID(0x01, 0x5e) 0 0 0xf1100000 0x10000>, /* SPI0-DEV1 */ + <MBUS_ID(0x01, 0x9a) 0 0 0xf1110000 0x10000>; /* SPI1-DEV2 */ + +For further information on the MBus bindings, please see the MBus +DT documentation: +Documentation/devicetree/bindings/bus/mvebu-mbus.txt diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index 1b14d69d8903..d2ca153614f9 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -6,10 +6,13 @@ and display controllers using the SPI communication interface. Required Properties: - compatible: should be one of the following. - "rockchip,rk3066-spi" for rk3066. - "rockchip,rk3188-spi", "rockchip,rk3066-spi" for rk3188. - "rockchip,rk3288-spi", "rockchip,rk3066-spi" for rk3288. - "rockchip,rk3399-spi", "rockchip,rk3066-spi" for rk3399. + "rockchip,rk3036-spi" for rk3036 SoCS. + "rockchip,rk3066-spi" for rk3066 SoCs. + "rockchip,rk3188-spi" for rk3188 SoCs. + "rockchip,rk3228-spi" for rk3228 SoCS. + "rockchip,rk3288-spi" for rk3288 SoCs. + "rockchip,rk3368-spi" for rk3368 SoCs. + "rockchip,rk3399-spi" for rk3399 SoCs. - reg: physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index 6dbdeb3c361a..49028a4f5df1 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -9,7 +9,8 @@ Required SoC Specific Properties: - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms - samsung,s3c6410-spi: for s3c6410 platforms - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms - - samsung,exynos7-spi: for exynos7 platforms + - samsung,exynos5433-spi: for exynos5433 compatible controllers + - samsung,exynos7-spi: for exynos7 platforms <DEPRECATED> - reg: physical base address of the controller and length of memory mapped region. @@ -23,6 +24,15 @@ Required SoC Specific Properties: - dma-names: Names for the dma channels. There must be at least one channel named "tx" for transmit and named "rx" for receive. +- clocks: specifies the clock IDs provided to the SPI controller; they are + required for interacting with the controller itself, for synchronizing the bus + and as I/O clock (the latter is required by exynos5433 and exynos7). + +- clock-names: string names of the clocks in the 'clocks' property; for all the + the devices the names must be "spi", "spi_busclkN" (where N is determined by + "samsung,spi-src-clk"), while Exynos5433 should specify a third clock + "spi_ioclk" for the I/O clock. + Required Board Specific Properties: - #address-cells: should be 1. @@ -40,6 +50,9 @@ Optional Board Specific Properties: - cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt) +- no-cs-readback: the CS line is disconnected, therefore the device should not + operate based on CS signalling. + SPI Controller specific data in SPI slave nodes: - The spi slave nodes should provide the following information which is required diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt index 50b14f6b53a3..e65fde4a7388 100644 --- a/Documentation/devicetree/bindings/spi/ti_qspi.txt +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -20,7 +20,7 @@ Optional properties: chipselect register and offset of that register. NOTE: TI QSPI controller requires different pinmux and IODelay -paramaters for Mode-0 and Mode-3 operations, which needs to be set up by +parameters for Mode-0 and Mode-3 operations, which needs to be set up by the bootloader (U-Boot). Default configuration only supports Mode-0 operation. Hence, "spi-cpol" and "spi-cpha" DT properties cannot be specified in the slave nodes of TI QSPI controller without appropriate diff --git a/MAINTAINERS b/MAINTAINERS index 3a7b3998e845..403c162b0b28 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -10921,6 +10921,7 @@ L: linux-spi@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git Q: http://patchwork.kernel.org/project/spi-devel-general/list/ S: Maintained +F: Documentation/devicetree/bindings/spi/ F: Documentation/spi/ F: drivers/spi/ F: include/linux/spi/ diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 4b931ec8d90b..d6fb8d4b7786 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -411,6 +411,7 @@ config SPI_OMAP24XX tristate "McSPI driver for OMAP" depends on HAS_DMA depends on ARCH_OMAP2PLUS || COMPILE_TEST + select SG_SPLIT help SPI master controller for OMAP24XX and later Multichannel SPI (McSPI) modules. diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 3c74d003535b..185367ef6576 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -56,6 +56,7 @@ obj-$(CONFIG_SPI_MT65XX) += spi-mt65xx.o obj-$(CONFIG_SPI_MXS) += spi-mxs.o obj-$(CONFIG_SPI_NUC900) += spi-nuc900.o obj-$(CONFIG_SPI_OC_TINY) += spi-oc-tiny.o +spi-octeon-objs := spi-cavium.o spi-cavium-octeon.o obj-$(CONFIG_SPI_OCTEON) += spi-octeon.o obj-$(CONFIG_SPI_OMAP_UWIRE) += spi-omap-uwire.o obj-$(CONFIG_SPI_OMAP_100K) += spi-omap-100k.o diff --git a/drivers/spi/spi-bfin-sport.c b/drivers/spi/spi-bfin-sport.c index 6c967555a56a..01d0ba9c5942 100644 --- a/drivers/spi/spi-bfin-sport.c +++ b/drivers/spi/spi-bfin-sport.c @@ -64,8 +64,6 @@ struct bfin_sport_spi_master_data { /* Pin request list */ u16 *pin_req; - /* Driver message queue */ - struct workqueue_struct *workqueue; struct work_struct pump_messages; spinlock_t lock; struct list_head queue; @@ -300,7 +298,7 @@ bfin_sport_spi_giveback(struct bfin_sport_spi_master_data *drv_data) drv_data->cur_msg = NULL; drv_data->cur_transfer = NULL; drv_data->cur_chip = NULL; - queue_work(drv_data->workqueue, &drv_data->pump_messages); + schedule_work(&drv_data->pump_messages); spin_unlock_irqrestore(&drv_data->lock, flags); if (!drv_data->cs_change) @@ -556,7 +554,7 @@ bfin_sport_spi_transfer(struct spi_device *spi, struct spi_message *msg) list_add_tail(&msg->queue, &drv_data->queue); if (drv_data->run && !drv_data->busy) - queue_work(drv_data->workqueue, &drv_data->pump_messages); + schedule_work(&drv_data->pump_messages); spin_unlock_irqrestore(&drv_data->lock, flags); @@ -666,12 +664,7 @@ bfin_sport_spi_init_queue(struct bfin_sport_spi_master_data *drv_data) tasklet_init(&drv_data->pump_transfers, bfin_sport_spi_pump_transfers, (unsigned long)drv_data); - /* init messages workqueue */ INIT_WORK(&drv_data->pump_messages, bfin_sport_spi_pump_messages); - drv_data->workqueue = - create_singlethread_workqueue(dev_name(drv_data->master->dev.parent)); - if (drv_data->workqueue == NULL) - return -EBUSY; return 0; } @@ -694,7 +687,7 @@ bfin_sport_spi_start_queue(struct bfin_sport_spi_master_data *drv_data) drv_data->cur_chip = NULL; spin_unlock_irqrestore(&drv_data->lock, flags); - queue_work(drv_data->workqueue, &drv_data->pump_messages); + schedule_work(&drv_data->pump_messages); return 0; } @@ -738,7 +731,7 @@ bfin_sport_spi_destroy_queue(struct bfin_sport_spi_master_data *drv_data) if (status) return status; - destroy_workqueue(drv_data->workqueue); + flush_work(&drv_data->pump_messages); return 0; } diff --git a/drivers/spi/spi-bfin5xx.c b/drivers/spi/spi-bfin5xx.c index 1e91325bf39c..249c7a3677c9 100644 --- a/drivers/spi/spi-bfin5xx.c +++ b/drivers/spi/spi-bfin5xx.c @@ -67,8 +67,6 @@ struct bfin_spi_master_data { /* BFIN hookup */ struct bfin5xx_spi_master *master_info; - /* Driver message queue */ - struct workqueue_struct *workqueue; struct work_struct pump_messages; spinlock_t lock; struct list_head queue; @@ -359,7 +357,7 @@ static void bfin_spi_giveback(struct bfin_spi_master_data *drv_data) drv_data->cur_msg = NULL; drv_data->cur_transfer = NULL; drv_data->cur_chip = NULL; - queue_work(drv_data->workqueue, &drv_data->pump_messages); + schedule_work(&drv_data->pump_messages); spin_unlock_irqrestore(&drv_data->lock, flags); msg->state = NULL; @@ -946,7 +944,7 @@ static int bfin_spi_transfer(struct spi_device *spi, struct spi_message *msg) list_add_tail(&msg->queue, &drv_data->queue); if (drv_data->running && !drv_data->busy) - queue_work(drv_data->workqueue, &drv_data->pump_messages); + schedule_work(&drv_data->pump_messages); spin_unlock_irqrestore(&drv_data->lock, flags); @@ -1177,12 +1175,7 @@ static int bfin_spi_init_queue(struct bfin_spi_master_data *drv_data) tasklet_init(&drv_data->pump_transfers, bfin_spi_pump_transfers, (unsigned long)drv_data); - /* init messages workqueue */ INIT_WORK(&drv_data->pump_messages, bfin_spi_pump_messages); - drv_data->workqueue = create_singlethread_workqueue( - dev_name(drv_data->master->dev.parent)); - if (drv_data->workqueue == NULL) - return -EBUSY; return 0; } @@ -1204,7 +1197,7 @@ static int bfin_spi_start_queue(struct bfin_spi_master_data *drv_data) drv_data->cur_chip = NULL; spin_unlock_irqrestore(&drv_data->lock, flags); - queue_work(drv_data->workqueue, &drv_data->pump_messages); + schedule_work(&drv_data->pump_messages); return 0; } @@ -1246,7 +1239,7 @@ static int bfin_spi_destroy_queue(struct bfin_spi_master_data *drv_data) if (status != 0) return status; - destroy_workqueue(drv_data->workqueue); + flush_work(&drv_data->pump_messages); return 0; } diff --git a/drivers/spi/spi-cavium-octeon.c b/drivers/spi/spi-cavium-octeon.c new file mode 100644 index 000000000000..ee4703e84622 --- /dev/null +++ b/drivers/spi/spi-cavium-octeon.c @@ -0,0 +1,104 @@ +/* + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 2011, 2012 Cavium, Inc. + */ + +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/module.h> +#include <linux/io.h> +#include <linux/of.h> + +#include <asm/octeon/octeon.h> + +#include "spi-cavium.h" + +static int octeon_spi_probe(struct platform_device *pdev) +{ + struct resource *res_mem; + void __iomem *reg_base; + struct spi_master *master; + struct octeon_spi *p; + int err = -ENOENT; + + master = spi_alloc_master(&pdev->dev, sizeof(struct octeon_spi)); + if (!master) + return -ENOMEM; + p = spi_master_get_devdata(master); + platform_set_drvdata(pdev, master); + + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + reg_base = devm_ioremap_resource(&pdev->dev, res_mem); + if (IS_ERR(reg_base)) { + err = PTR_ERR(reg_base); + goto fail; + } + + p->register_base = reg_base; + p->sys_freq = octeon_get_io_clock_rate(); + + p->regs.config = 0; + p->regs.status = 0x08; + p->regs.tx = 0x10; + p->regs.data = 0x80; + + master->num_chipselect = 4; + master->mode_bits = SPI_CPHA | + SPI_CPOL | + SPI_CS_HIGH | + SPI_LSB_FIRST | + SPI_3WIRE; + + master->transfer_one_message = octeon_spi_transfer_one_message; + master->bits_per_word_mask = SPI_BPW_MASK(8); + master->max_speed_hz = OCTEON_SPI_MAX_CLOCK_HZ; + + master->dev.of_node = pdev->dev.of_node; + err = devm_spi_register_master(&pdev->dev, master); + if (err) { + dev_err(&pdev->dev, "register master failed: %d\n", err); + goto fail; + } + + dev_info(&pdev->dev, "OCTEON SPI bus driver\n"); + + return 0; +fail: + spi_master_put(master); + return err; +} + +static int octeon_spi_remove(struct platform_device *pdev) +{ + struct spi_master *master = platform_get_drvdata(pdev); + struct octeon_spi *p = spi_master_get_devdata(master); + + /* Clear the CSENA* and put everything in a known state. */ + writeq(0, p->register_base + OCTEON_SPI_CFG(p)); + + return 0; +} + +static const struct of_device_id octeon_spi_match[] = { + { .compatible = "cavium,octeon-3010-spi", }, + {}, +}; +MODULE_DEVICE_TABLE(of, octeon_spi_match); + +static struct platform_driver octeon_spi_driver = { + .driver = { + .name = "spi-octeon", + .of_match_table = octeon_spi_match, + }, + .probe = octeon_spi_probe, + .remove = octeon_spi_remove, +}; + +module_platform_driver(octeon_spi_driver); + +MODULE_DESCRIPTION("Cavium, Inc. OCTEON SPI bus driver"); +MODULE_AUTHOR("David Daney"); +MODULE_LICENSE("GPL"); diff --git a/drivers/spi/spi-cavium.c b/drivers/spi/spi-cavium.c new file mode 100644 index 000000000000..5aaf21582cb5 --- /dev/null +++ b/drivers/spi/spi-cavium.c @@ -0,0 +1,151 @@ +/* + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 2011, 2012 Cavium, Inc. + */ + +#include <linux/spi/spi.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/io.h> + +#include "spi-cavium.h" + +static void octeon_spi_wait_ready(struct octeon_spi *p) +{ + union cvmx_mpi_sts mpi_sts; + unsigned int loops = 0; + + do { + if (loops++) + __delay(500); + mpi_sts.u64 = readq(p->register_base + OCTEON_SPI_STS(p)); + } while (mpi_sts.s.busy); +} + +static int octeon_spi_do_transfer(struct octeon_spi *p, + struct spi_message *msg, + struct spi_transfer *xfer, + bool last_xfer) +{ + struct spi_device *spi = msg->spi; + union cvmx_mpi_cfg mpi_cfg; + union cvmx_mpi_tx mpi_tx; + unsigned int clkdiv; + int mode; + bool cpha, cpol; + const u8 *tx_buf; + u8 *rx_buf; + int len; + int i; + + mode = spi->mode; + cpha = mode & SPI_CPHA; + cpol = mode & SPI_CPOL; + + clkdiv = p->sys_freq / (2 * xfer->speed_hz); + + mpi_cfg.u64 = 0; + + mpi_cfg.s.clkdiv = clkdiv; + mpi_cfg.s.cshi = (mode & SPI_CS_HIGH) ? 1 : 0; + mpi_cfg.s.lsbfirst = (mode & SPI_LSB_FIRST) ? 1 : 0; + mpi_cfg.s.wireor = (mode & SPI_3WIRE) ? 1 : 0; + mpi_cfg.s.idlelo = cpha != cpol; + mpi_cfg.s.cslate = cpha ? 1 : 0; + mpi_cfg.s.enable = 1; + + if (spi->chip_select < 4) < |