diff options
31 files changed, 1953 insertions, 1156 deletions
diff --git a/Documentation/devicetree/bindings/security/tpm/st33zp24-spi.txt b/Documentation/devicetree/bindings/security/tpm/st33zp24-spi.txt new file mode 100644 index 000000000000..158b0165e01c --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/st33zp24-spi.txt @@ -0,0 +1,34 @@ +* STMicroelectronics SAS. ST33ZP24 TPM SoC + +Required properties: +- compatible: Should be "st,st33zp24-spi". +- spi-max-frequency: Maximum SPI frequency (<= 10000000). + +Optional ST33ZP24 Properties: +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- lpcpd-gpios: Output GPIO pin used for ST33ZP24 power management D1/D2 state. +If set, power must be present when the platform is going into sleep/hibernate mode. + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBoard xM with ST33ZP24 on SPI4): + +&mcspi4 { + + status = "okay"; + + st33zp24@0 { + + compatible = "st,st33zp24-spi"; + + spi-max-frequency = <10000000>; + + interrupt-parent = <&gpio5>; + interrupts = <7 IRQ_TYPE_LEVEL_HIGH>; + + lpcpd-gpios = <&gpio5 15 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/security/Smack.txt b/Documentation/security/Smack.txt index b6ef7e9dba30..abc82f85215b 100644 --- a/Documentation/security/Smack.txt +++ b/Documentation/security/Smack.txt @@ -33,11 +33,18 @@ The current git repository for Smack user space is: git://github.com/smack-team/smack.git This should make and install on most modern distributions. -There are three commands included in smackutil: +There are five commands included in smackutil: -smackload - properly formats data for writing to /smack/load -smackcipso - properly formats data for writing to /smack/cipso chsmack - display or set Smack extended attribute values +smackctl - load the Smack access rules +smackaccess - report if a process with one label has access + to an object with another + +These two commands are obsolete with the introduction of +the smackfs/load2 and smackfs/cipso2 interfaces. + +smackload - properly formats data for writing to smackfs/load +smackcipso - properly formats data for writing to smackfs/cipso In keeping with the intent of Smack, configuration data is minimal and not strictly required. The most important @@ -47,9 +54,9 @@ of this, but it can be manually as well. Add this line to /etc/fstab: - smackfs /smack smackfs smackfsdef=* 0 0 + smackfs /sys/fs/smackfs smackfs defaults 0 0 -and create the /smack directory for mounting. +The /sys/fs/smackfs directory is created by the kernel. Smack uses extended attributes (xattrs) to store labels on filesystem objects. The attributes are stored in the extended attribute security @@ -92,13 +99,13 @@ There are multiple ways to set a Smack label on a file: # attr -S -s SMACK64 -V "value" path # chsmack -a value path -A process can see the smack label it is running with by +A process can see the Smack label it is running with by reading /proc/self/attr/current. A process with CAP_MAC_ADMIN -can set the process smack by writing there. +can set the process Smack by writing there. Most Smack configuration is accomplished by writing to files -in the smackfs filesystem. This pseudo-filesystem is usually -mounted on /smack. +in the smackfs filesystem. This pseudo-filesystem is mounted +on /sys/fs/smackfs. access This interface reports whether a subject with the specified @@ -206,23 +213,30 @@ onlycap file or cleared by writing "-" to the file. ptrace This is used to define the current ptrace policy - 0 - default: this is the policy that relies on smack access rules. + 0 - default: this is the policy that relies on Smack access rules. For the PTRACE_READ a subject needs to have a read access on object. For the PTRACE_ATTACH a read-write access is required. 1 - exact: this is the policy that limits PTRACE_ATTACH. Attach is only allowed when subject's and object's labels are equal. - PTRACE_READ is not affected. Can be overriden with CAP_SYS_PTRACE. + PTRACE_READ is not affected. Can be overridden with CAP_SYS_PTRACE. 2 - draconian: this policy behaves like the 'exact' above with an - exception that it can't be overriden with CAP_SYS_PTRACE. + exception that it can't be overridden with CAP_SYS_PTRACE. revoke-subject Writing a Smack label here sets the access to '-' for all access rules with that subject label. +unconfined + If the kernel is configured with CONFIG_SECURITY_SMACK_BRINGUP + a process with CAP_MAC_ADMIN can write a label into this interface. + Thereafter, accesses that involve that label will be logged and + the access permitted if it wouldn't be otherwise. Note that this + is dangerous and can ruin the proper labeling of your system. + It should never be used in production. You can add access rules in /etc/smack/accesses. They take the form: subjectlabel objectlabel access -access is a combination of the letters rwxa which specify the +access is a combination of the letters rwxatb which specify the kind of access permitted a subject with subjectlabel on an object with objectlabel. If there is no rule no access is allowed. @@ -318,8 +332,9 @@ each of the subject and the object. Labels -Smack labels are ASCII character strings, one to twenty-three characters in -length. Single character labels using special characters, that being anything +Smack labels are ASCII character strings. They can be up to 255 characters +long, but keeping them to twenty-three characters is recommended. +Single character labels using special characters, that being anything other than a letter or digit, are reserved for use by the Smack development team. Smack labels are unstructured, case sensitive, and the only operation ever performed on them is comparison for equality. Smack labels cannot @@ -335,10 +350,9 @@ There are some predefined labels: ? Pronounced "huh", a single question mark character. @ Pronounced "web", a single at sign character. -Every task on a Smack system is assigned a label. System tasks, such as -init(8) and systems daemons, are run with the floor ("_") label. User tasks -are assigned labels according to the specification found in the -/etc/smack/user configuration file. +Every task on a Smack system is assigned a label. The Smack label +of a process will usually be assigned by the system initialization +mechanism. Access Rules @@ -393,6 +407,7 @@ describe access modes: w: indicates that write access should be granted. x: indicates that execute access should be granted. t: indicates that the rule requests transmutation. + b: indicates that the rule should be reported for bring-up. Uppercase values for the specification letters are allowed as well. Access mode specifications can be in any order. Examples of acceptable rules @@ -402,6 +417,7 @@ are: Secret Unclass R Manager Game x User HR w + Snap Crackle rwxatb New Old rRrRr Closed Off - @@ -413,7 +429,7 @@ Examples of unacceptable rules are: Spaces are not allowed in labels. Since a subject always has access to files with the same label specifying a rule for that case is pointless. Only -valid letters (rwxatRWXAT) and the dash ('-') character are allowed in +valid letters (rwxatbRWXATB) and the dash ('-') character are allowed in access specifications. The dash is a placeholder, so "a-r" is the same as "ar". A lone dash is used to specify that no access should be allowed. @@ -462,16 +478,11 @@ receiver. The receiver is not required to have read access to the sender. Setting Access Rules The configuration file /etc/smack/accesses contains the rules to be set at -system startup. The contents are written to the special file /smack/load. -Rules can be written to /smack/load at any time and take effect immediately. -For any pair of subject and object labels there can be only one rule, with the -most recently specified overriding any earlier specification. - -The program smackload is provided to ensure data is formatted -properly when written to /smack/load. This program reads lines -of the form - - subjectlabel objectlabel mode. +system startup. The contents are written to the special file +/sys/fs/smackfs/load2. Rules can be added at any time and take effect +immediately. For any pair of subject and object labels there can be only +one rule, with the most recently specified overriding any earlier +specification. Task Attribute @@ -488,7 +499,10 @@ only be changed by a process with privilege. Privilege -A process with CAP_MAC_OVERRIDE is privileged. +A process with CAP_MAC_OVERRIDE or CAP_MAC_ADMIN is privileged. +CAP_MAC_OVERRIDE allows the process access to objects it would +be denied otherwise. CAP_MAC_ADMIN allows a process to change +Smack data, including rules and attributes. Smack Networking @@ -510,14 +524,14 @@ intervention. Unlabeled packets that come into the system will be given the ambient label. Smack requires configuration in the case where packets from a system that is -not smack that speaks CIPSO may be encountered. Usually this will be a Trusted +not Smack that speaks CIPSO may be encountered. Usually this will be a Trusted Solaris system, but there are other, less widely deployed systems out there. CIPSO provides 3 important values, a Domain Of Interpretation (DOI), a level, and a category set with each packet. The DOI is intended to identify a group of systems that use compatible labeling schemes, and the DOI specified on the -smack system must match that of the remote system or packets will be -discarded. The DOI is 3 by default. The value can be read from /smack/doi and -can be changed by writing to /smack/doi. +Smack system must match that of the remote system or packets will be +discarded. The DOI is 3 by default. The value can be read from +/sys/fs/smackfs/doi and can be changed by writing to /sys/fs/smackfs/doi. The label and category set are mapped to a Smack label as defined in /etc/smack/cipso. @@ -539,15 +553,13 @@ The ":" and "," characters are permitted in a Smack label but have no special meaning. The mapping of Smack labels to CIPSO values is defined by writing to -/smack/cipso. Again, the format of data written to this special file -is highly restrictive, so the program smackcipso is provided to -ensure the writes are done properly. This program takes mappings -on the standard input and sends them to /smack/cipso properly. +/sys/fs/smackfs/cipso2. In addition to explicit mappings Smack supports direct CIPSO mappings. One CIPSO level is used to indicate that the category set passed in the packet is in fact an encoding of the Smack label. The level used is 250 by default. The -value can be read from /smack/direct and changed by writing to /smack/direct. +value can be read from /sys/fs/smackfs/direct and changed by writing to +/sys/fs/smackfs/direct. Socket Attributes @@ -565,8 +577,8 @@ sockets. Smack Netlabel Exceptions You will often find that your labeled application has to talk to the outside, -unlabeled world. To do this there's a special file /smack/netlabel where you can -add some exceptions in the form of : +unlabeled world. To do this there's a special file /sys/fs/smackfs/netlabel +where you can add some exceptions in the form of : @IP1 LABEL1 or @IP2/MASK LABEL2 @@ -574,22 +586,22 @@ It means that your application will have unlabeled access to @IP1 if it has write access on LABEL1, and access to the subnet @IP2/MASK if it has write access on LABEL2. -Entries in the /smack/netlabel file are matched by longest mask first, like in -classless IPv4 routing. +Entries in the /sys/fs/smackfs/netlabel file are matched by longest mask +first, like in classless IPv4 routing. A special label '@' and an option '-CIPSO' can be used there : @ means Internet, any application with any label has access to it -CIPSO means standard CIPSO networking If you don't know what CIPSO is and don't plan to use it, you can just do : -echo 127.0.0.1 -CIPSO > /smack/netlabel -echo 0.0.0.0/0 @ > /smack/netlabel +echo 127.0.0.1 -CIPSO > /sys/fs/smackfs/netlabel +echo 0.0.0.0/0 @ > /sys/fs/smackfs/netlabel If you use CIPSO on your 192.168.0.0/16 local network and need also unlabeled Internet access, you can have : -echo 127.0.0.1 -CIPSO > /smack/netlabel -echo 192.168.0.0/16 -CIPSO > /smack/netlabel -echo 0.0.0.0/0 @ > /smack/netlabel +echo 127.0.0.1 -CIPSO > /sys/fs/smackfs/netlabel +echo 192.168.0.0/16 -CIPSO > /sys/fs/smackfs/netlabel +echo 0.0.0.0/0 @ > /sys/fs/smackfs/netlabel Writing Applications for Smack @@ -676,7 +688,7 @@ Smack auditing If you want Smack auditing of security events, you need to set CONFIG_AUDIT in your kernel configuration. By default, all denied events will be audited. You can change this behavior by -writing a single character to the /smack/logging file : +writing a single character to the /sys/fs/smackfs/logging file : 0 : no logging 1 : log denied (default) 2 : log accepted @@ -686,3 +698,20 @@ Events are logged as 'key=value' pairs, for each event you at least will get the subject, the object, the rights requested, the action, the kernel function that triggered the event, plus other pairs depending on the type of event audited. + +Bringup Mode + +Bringup mode provides logging features that can make application +configuration and system bringup easier. Configure the kernel with +CONFIG_SECURITY_SMACK_BRINGUP to enable these features. When bringup +mode is enabled accesses that succeed due to rules marked with the "b" +access mode will logged. When a new label is introduced for processes +rules can be added aggressively, marked with the "b". The logging allows +tracking of which rules actual get used for that label. + +Another feature of bringup mode is the "unconfined" option. Writing +a label to /sys/fs/smackfs/unconfined makes subjects with that label +able to access any object, and objects with that label accessible to +all subjects. Any access that is granted because a label is unconfined +is logged. This feature is dangerous, as files and directories may +be created in places they couldn't if the policy were being enforced. diff --git a/MAINTAINERS b/MAINTAINERS index 7a8f367b4ebc..c72a7baec55c 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -9968,6 +9968,7 @@ F: drivers/media/pci/tw68/ TPM DEVICE DRIVER M: Peter Huewe <peterhuewe@gmx.de> M: Marcel Selhorst <tpmdd@selhorst.net> +R: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> W: http://tpmdd.sourceforge.net L: tpmdd-devel@lists.sourceforge.net (moderated for non-subscribers) Q: git git://github.com/PeterHuewe/linux-tpmdd.git diff --git a/drivers/char/tpm/Kconfig b/drivers/char/tpm/Kconfig index 9d4e37549eb2..3b84a8b1bfbe 100644 --- a/drivers/char/tpm/Kconfig +++ b/drivers/char/tpm/Kconfig @@ -25,13 +25,14 @@ menuconfig TCG_TPM if TCG_TPM config TCG_TIS - tristate "TPM Interface Specification 1.2 Interface" + tristate "TPM Interface Specification 1.2 Interface / TPM 2.0 FIFO Interface" depends on X86 ---help--- If you have a TPM security chip that is compliant with the - TCG TIS 1.2 TPM specification say Yes and it will be accessible - from within Linux. To compile this driver as a module, choose - M here; the module will be called tpm_tis. + TCG TIS 1.2 TPM specification (TPM1.2) or the TCG PTP FIFO + specification (TPM2.0) say Yes and it will be accessible from + within Linux. To compile this driver as a module, choose M here; + the module will be called tpm_tis. config TCG_TIS_I2C_ATMEL tristate "TPM Interface Specification 1.2 Interface (I2C - Atmel)" @@ -100,16 +101,6 @@ config TCG_IBMVTPM will be accessible from within Linux. To compile this driver as a module, choose M here; the module will be called tpm_ibmvtpm. -config TCG_TIS_I2C_ST33 - tristate "TPM Interface Specification 1.2 Interface (I2C - STMicroelectronics)" - depends on I2C - depends on GPIOLIB - ---help--- - If you have a TPM security chip from STMicroelectronics working with - an I2C bus say Yes and it will be accessible from within Linux. - To compile this driver as a module, choose M here; the module will be - called tpm_i2c_stm_st33. - config TCG_XEN tristate "XEN TPM Interface" depends on TCG_TPM && XEN @@ -131,4 +122,5 @@ config TCG_CRB from within Linux. To compile this driver as a module, choose M here; the module will be called tpm_crb. +source "drivers/char/tpm/st33zp24/Kconfig" endif # TCG_TPM diff --git a/drivers/char/tpm/Makefile b/drivers/char/tpm/Makefile index 990cf183931d..56e8f1f3dc7e 100644 --- a/drivers/char/tpm/Makefile +++ b/drivers/char/tpm/Makefile @@ -20,6 +20,6 @@ obj-$(CONFIG_TCG_NSC) += tpm_nsc.o obj-$(CONFIG_TCG_ATMEL) += tpm_atmel.o obj-$(CONFIG_TCG_INFINEON) += tpm_infineon.o obj-$(CONFIG_TCG_IBMVTPM) += tpm_ibmvtpm.o -obj-$(CONFIG_TCG_TIS_I2C_ST33) += tpm_i2c_stm_st33.o +obj-$(CONFIG_TCG_TIS_ST33ZP24) += st33zp24/ obj-$(CONFIG_TCG_XEN) += xen-tpmfront.o obj-$(CONFIG_TCG_CRB) += tpm_crb.o diff --git a/drivers/char/tpm/st33zp24/Kconfig b/drivers/char/tpm/st33zp24/Kconfig new file mode 100644 index 000000000000..09cb727864f0 --- /dev/null +++ b/drivers/char/tpm/st33zp24/Kconfig @@ -0,0 +1,30 @@ +config TCG_TIS_ST33ZP24 + tristate "STMicroelectronics TPM Interface Specification 1.2 Interface" + depends on GPIOLIB + ---help--- + STMicroelectronics ST33ZP24 core driver. It implements the core + TPM1.2 logic and hooks into the TPM kernel APIs. Physical layers will + register against it. + + To compile this driver as a module, choose m here. The module will be called + tpm_st33zp24. + +config TCG_TIS_ST33ZP24_I2C + tristate "TPM 1.2 ST33ZP24 I2C support" + depends on TCG_TIS_ST33ZP24 + depends on I2C + ---help--- + This module adds support for the STMicroelectronics TPM security chip + ST33ZP24 with i2c interface. + To compile this driver as a module, choose M here; the module will be + called tpm_st33zp24_i2c. + +config TCG_TIS_ST33ZP24_SPI + tristate "TPM 1.2 ST33ZP24 SPI support" + depends on TCG_TIS_ST33ZP24 + depends on SPI + ---help--- + This module adds support for the STMicroelectronics TPM security chip + ST33ZP24 with spi interface. + To compile this driver as a module, choose M here; the module will be + called tpm_st33zp24_spi. diff --git a/drivers/char/tpm/st33zp24/Makefile b/drivers/char/tpm/st33zp24/Makefile new file mode 100644 index 000000000000..74a722e5e068 --- /dev/null +++ b/drivers/char/tpm/st33zp24/Makefile @@ -0,0 +1,12 @@ +# +# Makefile for ST33ZP24 TPM 1.2 driver +# + +tpm_st33zp24-objs = st33zp24.o +obj-$(CONFIG_TCG_TIS_ST33ZP24) += tpm_st33zp24.o + +tpm_st33zp24_i2c-objs = i2c.o +obj-$(CONFIG_TCG_TIS_ST33ZP24_I2C) += tpm_st33zp24_i2c.o + +tpm_st33zp24_spi-objs = spi.o +obj-$(CONFIG_TCG_TIS_ST33ZP24_SPI) += tpm_st33zp24_spi.o diff --git a/drivers/char/tpm/st33zp24/i2c.c b/drivers/char/tpm/st33zp24/i2c.c new file mode 100644 index 000000000000..ad1ee180e0c2 --- /dev/null +++ b/drivers/char/tpm/st33zp24/i2c.c @@ -0,0 +1,276 @@ +/* + * STMicroelectronics TPM I2C Linux driver for TPM ST33ZP24 + * Copyright (C) 2009 - 2015 STMicroelectronics + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/module.h> +#include <linux/i2c.h> +#include <linux/gpio.h> +#include <linux/of_irq.h> +#include <linux/of_gpio.h> +#include <linux/tpm.h> +#include <linux/platform_data/st33zp24.h> + +#include "st33zp24.h" + +#define TPM_DUMMY_BYTE 0xAA + +struct st33zp24_i2c_phy { + struct i2c_client *client; + u8 buf[TPM_BUFSIZE + 1]; + int io_lpcpd; +}; + +/* + * write8_reg + * Send byte to the TIS register according to the ST33ZP24 I2C protocol. + * @param: tpm_register, the tpm tis register where the data should be written + * @param: tpm_data, the tpm_data to write inside the tpm_register + * @param: tpm_size, The length of the data + * @return: Returns negative errno, or else the number of bytes written. + */ +static int write8_reg(void *phy_id, u8 tpm_register, u8 *tpm_data, int tpm_size) +{ + struct st33zp24_i2c_phy *phy = phy_id; + + phy->buf[0] = tpm_register; + memcpy(phy->buf + 1, tpm_data, tpm_size); + return i2c_master_send(phy->client, phy->buf, tpm_size + 1); +} /* write8_reg() */ + +/* + * read8_reg + * Recv byte from the TIS register according to the ST33ZP24 I2C protocol. + * @param: tpm_register, the tpm tis register where the data should be read + * @param: tpm_data, the TPM response + * @param: tpm_size, tpm TPM response size to read. + * @return: number of byte read successfully: should be one if success. + */ +static int read8_reg(void *phy_id, u8 tpm_register, u8 *tpm_data, int tpm_size) +{ + struct st33zp24_i2c_phy *phy = phy_id; + u8 status = 0; + u8 data; + + data = TPM_DUMMY_BYTE; + status = write8_reg(phy, tpm_register, &data, 1); + if (status == 2) + status = i2c_master_recv(phy->client, tpm_data, tpm_size); + return status; +} /* read8_reg() */ + +/* + * st33zp24_i2c_send + * Send byte to the TIS register according to the ST33ZP24 I2C protocol. + * @param: phy_id, the phy description + * @param: tpm_register, the tpm tis register where the data should be written + * @param: tpm_data, the tpm_data to write inside the tpm_register + * @param: tpm_size, the length of the data + * @return: number of byte written successfully: should be one if success. + */ +static int st33zp24_i2c_send(void *phy_id, u8 tpm_register, u8 *tpm_data, + int tpm_size) +{ + return write8_reg(phy_id, tpm_register | TPM_WRITE_DIRECTION, tpm_data, + tpm_size); +} + +/* + * st33zp24_i2c_recv + * Recv byte from the TIS register according to the ST33ZP24 I2C protocol. + * @param: phy_id, the phy description + * @param: tpm_register, the tpm tis register where the data should be read + * @param: tpm_data, the TPM response + * @param: tpm_size, tpm TPM response size to read. + * @return: number of byte read successfully: should be one if success. + */ +static int st33zp24_i2c_recv(void *phy_id, u8 tpm_register, u8 *tpm_data, + int tpm_size) +{ + return read8_reg(phy_id, tpm_register, tpm_data, tpm_size); +} + +static const struct st33zp24_phy_ops i2c_phy_ops = { + .send = st33zp24_i2c_send, + .recv = st33zp24_i2c_recv, +}; + +#ifdef CONFIG_OF +static int st33zp24_i2c_of_request_resources(struct st33zp24_i2c_phy *phy) +{ + struct device_node *pp; + struct i2c_client *client = phy->client; + int gpio; + int ret; + + pp = client->dev.of_node; + if (!pp) { + dev_err(&client->dev, "No platform data\n"); + return -ENODEV; + } + + /* Get GPIO from device tree */ + gpio = of_get_named_gpio(pp, "lpcpd-gpios", 0); + if (gpio < 0) { + dev_err(&client->dev, + "Failed to retrieve lpcpd-gpios from dts.\n"); + phy->io_lpcpd = -1; + /* + * lpcpd pin is not specified. This is not an issue as + * power management can be also managed by TPM specific + * commands. So leave with a success status code. + */ + return 0; + } + /* GPIO request and configuration */ + ret = devm_gpio_request_one(&client->dev, gpio, + GPIOF_OUT_INIT_HIGH, "TPM IO LPCPD"); + if (ret) { + dev_err(&client->dev, "Failed to request lpcpd pin\n"); + return -ENODEV; + } + phy->io_lpcpd = gpio; + + return 0; +} +#else +static int st33zp24_i2c_of_request_resources(struct st33zp24_i2c_phy *phy) +{ + return -ENODEV; +} +#endif + +static int st33zp24_i2c_request_resources(struct i2c_client *client, + struct st33zp24_i2c_phy *phy) +{ + struct st33zp24_platform_data *pdata; + int ret; + + pdata = client->dev.platform_data; + if (!pdata) { + dev_err(&client->dev, "No platform data\n"); + return -ENODEV; + } + + /* store for late use */ + phy->io_lpcpd = pdata->io_lpcpd; + + if (gpio_is_valid(pdata->io_lpcpd)) { + ret = devm_gpio_request_one(&client->dev, + pdata->io_lpcpd, GPIOF_OUT_INIT_HIGH, + "TPM IO_LPCPD"); + if (ret) { + dev_err(&client->dev, "Failed to request lpcpd pin\n"); + return ret; + } + } + + return 0; +} + +/* + * st33zp24_i2c_probe initialize the TPM device + * @param: client, the i2c_client drescription (TPM I2C description). + * @param: id, the i2c_device_id struct. + * @return: 0 in case of success. + * -1 in other case. + */ +static int st33zp24_i2c_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + int ret; + struct st33zp24_platform_data *pdata; + struct st33zp24_i2c_phy *phy; + + if (!client) { + pr_info("%s: i2c client is NULL. Device not accessible.\n", + __func__); + return -ENODEV; + } + + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { + dev_info(&client->dev, "client not i2c capable\n"); + return -ENODEV; + } + + phy = devm_kzalloc(&client->dev, sizeof(struct st33zp24_i2c_phy), + GFP_KERNEL); + if (!phy) + return -ENOMEM; + + phy->client = client; + pdata = client->dev.platform_data; + if (!pdata && client->dev.of_node) { + ret = st33zp24_i2c_of_request_resources(phy); + if (ret) + return ret; + } else if (pdata) { + ret = st33zp24_i2c_request_resources(client, phy); + if (ret) + return ret; + } + + return st33zp24_probe(phy, &i2c_phy_ops, &client->dev, client->irq, + phy->io_lpcpd); +} + +/* + * st33zp24_i2c_remove remove the TPM device + * @param: client, the i2c_client description (TPM I2C description). + * @return: 0 in case of success. + */ +static int st33zp24_i2c_remove(struct i2c_client *client) +{ + struct tpm_chip *chip = i2c_get_clientdata(client); + + return st33zp24_remove(chip); +} + +static const struct i2c_device_id st33zp24_i2c_id[] = { + {TPM_ST33_I2C, 0}, + {} +}; +MODULE_DEVICE_TABLE(i2c, st33zp24_i2c_id); + +#ifdef CONFIG_OF +static const struct of_device_id of_st33zp24_i2c_match[] = { + { .compatible = "st,st33zp24-i2c", }, + {} +}; +MODULE_DEVICE_TABLE(of, of_st33zp24_i2c_match); +#endif + +static SIMPLE_DEV_PM_OPS(st33zp24_i2c_ops, st33zp24_pm_suspend, + st33zp24_pm_resume); + +static struct i2c_driver st33zp24_i2c_driver = { + .driver = { + .owner = THIS_MODULE, + .name = TPM_ST33_I2C, + .pm = &st33zp24_i2c_ops, + .of_match_table = of_match_ptr(of_st33zp24_i2c_match), + }, + .probe = st33zp24_i2c_probe, + .remove = st33zp24_i2c_remove, + .id_table = st33zp24_i2c_id +}; + +module_i2c_driver(st33zp24_i2c_driver); + +MODULE_AUTHOR("TPM support (TPMsupport@list.st.com)"); +MODULE_DESCRIPTION("STM TPM 1.2 I2C ST33 Driver"); +MODULE_VERSION("1.3.0"); +MODULE_LICENSE("GPL"); diff --git a/drivers/char/tpm/st33zp24/spi.c b/drivers/char/tpm/st33zp24/spi.c new file mode 100644 index 000000000000..f0184a1b0c1c --- /dev/null +++ b/drivers/char/tpm/st33zp24/spi.c @@ -0,0 +1,399 @@ +/* + * STMicroelectronics TPM SPI Linux driver for TPM ST33ZP24 + * Copyright (C) 2009 - 2015 STMicroelectronics + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * t |