diff options
99 files changed, 11511 insertions, 975 deletions
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt index 02c27004d4a8..a74b37b07e5c 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt @@ -1,16 +1,20 @@ NVIDIA Tegra Power Management Controller (PMC) +== Power Management Controller Node == + The PMC block interacts with an external Power Management Unit. The PMC mostly controls the entry and exit of the system from different sleep modes. It provides power-gating controllers for SoC and CPU power-islands. Required properties: - name : Should be pmc -- compatible : For Tegra20, must contain "nvidia,tegra20-pmc". For Tegra30, - must contain "nvidia,tegra30-pmc". For Tegra114, must contain - "nvidia,tegra114-pmc". For Tegra124, must contain "nvidia,tegra124-pmc". - Otherwise, must contain "nvidia,<chip>-pmc", plus at least one of the - above, where <chip> is tegra132. +- compatible : Should contain one of the following: + For Tegra20 must contain "nvidia,tegra20-pmc". + For Tegra30 must contain "nvidia,tegra30-pmc". + For Tegra114 must contain "nvidia,tegra114-pmc" + For Tegra124 must contain "nvidia,tegra124-pmc" + For Tegra132 must contain "nvidia,tegra124-pmc" + For Tegra210 must contain "nvidia,tegra210-pmc" - reg : Offset and length of the register set for the device - clocks : Must contain an entry for each entry in clock-names. See ../clocks/clock-bindings.txt for details. @@ -68,6 +72,11 @@ Optional properties for hardware-triggered thermal reset (inside 'i2c-thermtrip' Defaults to 0. Valid values are described in section 12.5.2 "Pinmux Support" of the Tegra4 Technical Reference Manual. +Optional nodes: +- powergates : This node contains a hierarchy of power domain nodes, which + should match the powergates on the Tegra SoC. See "Powergate + Nodes" below. + Example: / SoC dts including file @@ -113,3 +122,76 @@ pmc@7000f400 { }; ... }; + + +== Powergate Nodes == + +Each of the powergate nodes represents a power-domain on the Tegra SoC +that can be power-gated by the Tegra PMC. The name of the powergate node +should be one of the below. Note that not every powergate is applicable +to all Tegra devices and the following list shows which powergates are +applicable to which devices. Please refer to the Tegra TRM for more +details on the various powergates. + + Name Description Devices Applicable + 3d 3D Graphics Tegra20/114/124/210 + 3d0 3D Graphics 0 Tegra30 + 3d1 3D Graphics 1 Tegra30 + aud Audio Tegra210 + dfd Debug Tegra210 + dis Display A Tegra114/124/210 + disb Display B Tegra114/124/210 + heg 2D Graphics Tegra30/114/124/210 + iram Internal RAM Tegra124/210 + mpe MPEG Encode All + nvdec NVIDIA Video Decode Engine Tegra210 + nvjpg NVIDIA JPEG Engine Tegra210 + pcie PCIE Tegra20/30/124/210 + sata SATA Tegra30/124/210 + sor Display interfaces Tegra124/210 + ve2 Video Encode Engine 2 Tegra210 + venc Video Encode Engine All + vdec Video Decode Engine Tegra20/30/114/124 + vic Video Imaging Compositor Tegra124/210 + xusba USB Partition A Tegra114/124/210 + xusbb USB Partition B Tegra114/124/210 + xusbc USB Partition C Tegra114/124/210 + +Required properties: + - clocks: Must contain an entry for each clock required by the PMC for + controlling a power-gate. See ../clocks/clock-bindings.txt for details. + - resets: Must contain an entry for each reset required by the PMC for + controlling a power-gate. See ../reset/reset.txt for details. + - #power-domain-cells: Must be 0. + +Example: + + pmc: pmc@7000e400 { + compatible = "nvidia,tegra210-pmc"; + reg = <0x0 0x7000e400 0x0 0x400>; + clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>; + clock-names = "pclk", "clk32k_in"; + + powergates { + pd_audio: aud { + clocks = <&tegra_car TEGRA210_CLK_APE>, + <&tegra_car TEGRA210_CLK_APB2APE>; + resets = <&tegra_car 198>; + #power-domain-cells = <0>; + }; + }; + }; + + +== Powergate Clients == + +Hardware blocks belonging to a power domain should contain a "power-domains" +property that is a phandle pointing to the corresponding powergate node. + +Example: + + adma: adma@702e2000 { + ... + power-domains = <&pd_audio>; + ... + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt new file mode 100644 index 000000000000..f633b5d0f8ca --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt @@ -0,0 +1,79 @@ +SAMSUNG Exynos SoCs SROM Controller driver. + +Required properties: +- compatible : Should contain "samsung,exynos4210-srom". + +- reg: offset and length of the register set + +Optional properties: +The SROM controller can be used to attach external peripherals. In this case +extra properties, describing the bus behind it, should be specified as below: + +- #address-cells: Must be set to 2 to allow device address translation. + Address is specified as (bank#, offset). + +- #size-cells: Must be set to 1 to allow device size passing + +- ranges: Must be set up to reflect the memory layout with four integer values + per bank: + <bank-number> 0 <parent address of bank> <size> + +Sub-nodes: +The actual device nodes should be added as subnodes to the SROMc node. These +subnodes, in addition to regular device specification, should contain the following +properties, describing configuration of the relevant SROM bank: + +Required properties: +- reg: bank number, base address (relative to start of the bank) and size of + the memory mapped for the device. Note that base address will be + typically 0 as this is the start of the bank. + +- samsung,srom-timing : array of 6 integers, specifying bank timings in the + following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. + Each value is specified in cycles and has the following + meaning and valid range: + Tacp : Page mode access cycle at Page mode (0 - 15) + Tcah : Address holding time after CSn (0 - 15) + Tcoh : Chip selection hold on OEn (0 - 15) + Tacc : Access cycle (0 - 31, the actual time is N + 1) + Tcos : Chip selection set-up before OEn (0 - 15) + Tacs : Address set-up before CSn (0 - 15) + +Optional properties: +- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used. + +- samsung,srom-page-mode : if page mode is set, 4 data page mode will be configured, + else normal (1 data) page mode will be set. + +Example: basic definition, no banks are configured + memory-controller@12570000 { + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + }; + +Example: SROMc with SMSC911x ethernet chip on bank 3 + memory-controller@12570000 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x04000000 0x20000 // Bank0 + 1 0 0x05000000 0x20000 // Bank1 + 2 0 0x06000000 0x20000 // Bank2 + 3 0 0x07000000 0x20000>; // Bank3 + + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + + ethernet@3,0 { + compatible = "smsc,lan9115"; + reg = <3 0 0x10000>; // Bank 3, offset = 0 + phy-mode = "mii"; + interrupt-parent = <&gpx0>; + interrupts = <5 8>; + reg-io-width = <2>; + smsc,irq-push-pull; + smsc,force-internal-phy; + + samsung,srom-page-mode; + samsung,srom-timing = <9 12 1 9 1 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/arm-versatile.txt b/Documentation/devicetree/bindings/mtd/arm-versatile.txt index beace4b89daa..4ec28796a3c0 100644 --- a/Documentation/devicetree/bindings/mtd/arm-versatile.txt +++ b/Documentation/devicetree/bindings/mtd/arm-versatile.txt @@ -1,8 +1,26 @@ Flash device on ARM Versatile board +These flash chips are found in the ARM reference designs like Integrator, +Versatile, RealView, Versatile Express etc. + +They are regular CFI compatible (Intel or AMD extended) flash chips with +some special write protect/VPP bits that can be controlled by the machine's +system controller. + Required properties: -- compatible : must be "arm,versatile-flash"; +- compatible : must be "arm,versatile-flash", "cfi-flash"; +- reg : memory address for the flash chip - bank-width : width in bytes of flash interface. +For the rest of the properties, see mtd-physmap.txt. + The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. + +Example: + +flash@34000000 { + compatible = "arm,versatile-flash", "cfi-flash"; + reg = <0x34000000 0x4000000>; + bank-width = <4>; +}; diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 75321ae23c08..b8cc395fffea 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -60,11 +60,14 @@ Required properties: - afi - pcie_x -Required properties on Tegra124 and later: +Required properties on Tegra124 and later (deprecated): - phys: Must contain an entry for each entry in phy-names. - phy-names: Must include the following entries: - pcie +These properties are deprecated in favour of per-lane PHYs define in each of +the root ports (see below). + Power supplies for Tegra20: - avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. - vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. @@ -122,11 +125,22 @@ Required properties: - Root port 0 uses 4 lanes, root port 1 is unused. - Both root ports use 2 lanes. -Example: +Required properties for Tegra124 and later: +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include |