diff options
116 files changed, 3057 insertions, 1640 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 608ba95d9461..d05533e6120b 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -957,6 +957,12 @@ serial port must already be setup and configured. Options are not yet supported. + lantiq,<addr> + Start an early, polled-mode console on a lantiq serial + (lqasc) port at the specified address. The serial port + must already be setup and configured. Options are not + yet supported. + lpuart,<addr> lpuart32,<addr> Use early console provided by Freescale LP UART driver diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index f86bb06c39e9..10276a46ecef 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -19,6 +19,7 @@ Required properties: - "altr,16550-FIFO128" - "fsl,16550-FIFO64" - "fsl,ns16550" + - "ti,da830-uart" - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. diff --git a/Documentation/devicetree/bindings/serial/serial.txt b/Documentation/devicetree/bindings/serial/serial.txt index fd970f76a7b8..b542a0ecf06e 100644 --- a/Documentation/devicetree/bindings/serial/serial.txt +++ b/Documentation/devicetree/bindings/serial/serial.txt @@ -23,7 +23,8 @@ Optional properties: they are available for use (wired and enabled by pinmux configuration). This depends on both the UART hardware and the board wiring. Note that this property is mutually-exclusive with "cts-gpios" and - "rts-gpios" above. + "rts-gpios" above, unless support is provided to switch between modes + dynamically. Examples: diff --git a/Documentation/devicetree/bindings/serial/slave-device.txt b/Documentation/devicetree/bindings/serial/slave-device.txt new file mode 100644 index 000000000000..f66037928f5f --- /dev/null +++ b/Documentation/devicetree/bindings/serial/slave-device.txt @@ -0,0 +1,36 @@ +Serial Slave Device DT binding + +This documents the binding structure and common properties for serial +attached devices. Common examples include Bluetooth, WiFi, NFC and GPS +devices. + +Serial attached devices shall be a child node of the host UART device the +slave device is attached to. It is expected that the attached device is +the only child node of the UART device. The slave device node name shall +reflect the generic type of device for the node. + +Required Properties: + +- compatible : A string reflecting the vendor and specific device the node + represents. + +Optional Properties: + +- max-speed : The maximum baud rate the device operates at. This should + only be present if the maximum is less than the slave device + can support. For example, a particular board has some signal + quality issue or the host processor can't support higher + baud rates. + +Example: + +serial@1234 { + compatible = "ns16550a"; + interrupts = <1>; + + bluetooth { + compatible = "brcm,bcm43341-bt"; + interrupt-parent = <&gpio>; + interrupts = <10>; + }; +}; diff --git a/MAINTAINERS b/MAINTAINERS index 7021feed5aa6..545633d6663d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -10927,6 +10927,14 @@ S: Maintained F: Documentation/devicetree/bindings/serial/ F: drivers/tty/serial/ +SERIAL DEVICE BUS +M: Rob Herring <robh@kernel.org> +L: linux-serial@vger.kernel.org +S: Maintained +F: Documentation/devicetree/bindings/serial/slave-device.txt +F: drivers/tty/serdev/ +F: include/linux/serdev.h + SERIAL IR RECEIVER M: Sean Young <sean@mess.org> L: linux-media@vger.kernel.org diff --git a/arch/arm/boot/dts/stih407-family.dtsi b/arch/arm/boot/dts/stih407-family.dtsi index 4c72dae2aefa..0fe03cb88628 100644 --- a/arch/arm/boot/dts/stih407-family.dtsi +++ b/arch/arm/boot/dts/stih407-family.dtsi @@ -222,9 +222,8 @@ compatible = "st,asc"; reg = <0x9830000 0x2c>; interrupts = <GIC_SPI 122 IRQ_TYPE_NONE>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_serial0>; clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; + /* Pinctrl moved out to a per-board configuration */ status = "disabled"; }; diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/stih407-pinctrl.dtsi index daab16b5ae64..bd1a82e8fffe 100644 --- a/arch/arm/boot/dts/stih407-pinctrl.dtsi +++ b/arch/arm/boot/dts/stih407-pinctrl.dtsi @@ -465,8 +465,16 @@ serial0 { pinctrl_serial0: serial0-0 { st,pins { - tx = <&pio17 0 ALT1 OUT>; - rx = <&pio17 1 ALT1 IN>; + tx = <&pio17 0 ALT1 OUT>; + rx = <&pio17 1 ALT1 IN>; + }; + }; + pinctrl_serial0_hw_flowctrl: serial0-0_hw_flowctrl { + st,pins { + tx = <&pio17 0 ALT1 OUT>; + rx = <&pio17 1 ALT1 IN>; + cts = <&pio17 2 ALT1 IN>; + rts = <&pio17 3 ALT1 OUT>; }; }; }; |