net: dsa: b53: Add support for Broadcom RoboSwitch

This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.

This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).

Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 files changed, 3264 insertions, 0 deletions

diff --git a/drivers/net/dsa/b53/Kconfig b/drivers/net/dsa/b53/Kconfig
new file mode 100644
index 000000000000..27f32a50df57
--- /dev/null
+++ b/drivers/net/dsa/b53/Kconfig
@@ -0,0 +1,33 @@
+menuconfig B53
+	tristate "Broadcom BCM53xx managed switch support"
+	depends on NET_DSA
+	help
+	  This driver adds support for Broadcom managed switch chips. It supports
+	  BCM5325E, BCM5365, BCM539x, BCM53115 and BCM53125 as well as BCM63XX
+	  integrated switches.
+
+config B53_SPI_DRIVER
+	tristate "B53 SPI connected switch driver"
+	depends on B53 && SPI
+	help
+	  Select to enable support for registering switches configured through SPI.
+
+config B53_MDIO_DRIVER
+	tristate "B53 MDIO connected switch driver"
+	depends on B53
+	help
+	  Select to enable support for registering switches configured through MDIO.
+
+config B53_MMAP_DRIVER
+	tristate "B53 MMAP connected switch driver"
+	depends on B53 && HAS_IOMEM
+	help
+	  Select to enable support for memory-mapped switches like the BCM63XX
+	  integrated switches.
+
+config B53_SRAB_DRIVER
+	tristate "B53 SRAB connected switch driver"
+	depends on B53 && HAS_IOMEM
+	help
+	  Select to enable support for memory-mapped Switch Register Access
+	  Bridge Registers (SRAB) like it is found on the BCM53010
diff --git a/drivers/net/dsa/b53/Makefile b/drivers/net/dsa/b53/Makefile
new file mode 100644
index 000000000000..7e6f9a8bfd75
--- /dev/null
+++ b/drivers/net/dsa/b53/Makefile
@@ -0,0 +1,6 @@
+obj-$(CONFIG_B53)		+= b53_common.o
+
+obj-$(CONFIG_B53_SPI_DRIVER)	+= b53_spi.o
+obj-$(CONFIG_B53_MDIO_DRIVER)	+= b53_mdio.o
+obj-$(CONFIG_B53_MMAP_DRIVER)	+= b53_mmap.o
+obj-$(CONFIG_B53_SRAB_DRIVER)	+= b53_srab.o
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
new file mode 100644
index 000000000000..6f0337d6dfa4
--- /dev/null
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -0,0 +1,1158 @@
+/*
+ * B53 switch driver main logic
+ *
+ * Copyright (C) 2011-2013 Jonas Gorski <jogo@openwrt.org>
+ * Copyright (C) 2016 Florian Fainelli <f.fainelli@gmail.com>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/delay.h>
+#include <linux/export.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_data/b53.h>
+#include <linux/phy.h>
+#include <net/dsa.h>
+
+#include "b53_regs.h"
+#include "b53_priv.h"
+
+struct b53_mib_desc {
+	u8 size;
+	u8 offset;
+	const char *name;
+};
+
+/* BCM5365 MIB counters */
+static const struct b53_mib_desc b53_mibs_65[] = {
+	{ 8, 0x00, "TxOctets" },
+	{ 4, 0x08, "TxDropPkts" },
+	{ 4, 0x10, "TxBroadcastPkts" },
+	{ 4, 0x14, "TxMulticastPkts" },
+	{ 4, 0x18, "TxUnicastPkts" },
+	{ 4, 0x1c, "TxCollisions" },
+	{ 4, 0x20, "TxSingleCollision" },
+	{ 4, 0x24, "TxMultipleCollision" },
+	{ 4, 0x28, "TxDeferredTransmit" },
+	{ 4, 0x2c, "TxLateCollision" },
+	{ 4, 0x30, "TxExcessiveCollision" },
+	{ 4, 0x38, "TxPausePkts" },
+	{ 8, 0x44, "RxOctets" },
+	{ 4, 0x4c, "RxUndersizePkts" },
+	{ 4, 0x50, "RxPausePkts" },
+	{ 4, 0x54, "Pkts64Octets" },
+	{ 4, 0x58, "Pkts65to127Octets" },
+	{ 4, 0x5c, "Pkts128to255Octets" },
+	{ 4, 0x60, "Pkts256to511Octets" },
+	{ 4, 0x64, "Pkts512to1023Octets" },
+	{ 4, 0x68, "Pkts1024to1522Octets" },
+	{ 4, 0x6c, "RxOversizePkts" },
+	{ 4, 0x70, "RxJabbers" },
+	{ 4, 0x74, "RxAlignmentErrors" },
+	{ 4, 0x78, "RxFCSErrors" },
+	{ 8, 0x7c, "RxGoodOctets" },
+	{ 4, 0x84, "RxDropPkts" },
+	{ 4, 0x88, "RxUnicastPkts" },
+	{ 4, 0x8c, "RxMulticastPkts" },
+	{ 4, 0x90, "RxBroadcastPkts" },
+	{ 4, 0x94, "RxSAChanges" },
+	{ 4, 0x98, "RxFragments" },
+};
+
+#define B53_MIBS_65_SIZE	ARRAY_SIZE(b53_mibs_65)
+
+/* BCM63xx MIB counters */
+static const struct b53_mib_desc b53_mibs_63xx[] = {
+	{ 8, 0x00, "TxOctets" },
+	{ 4, 0x08, "TxDropPkts" },
+	{ 4, 0x0c, "TxQoSPkts" },
+	{ 4, 0x10, "TxBroadcastPkts" },
+	{ 4, 0x14, "TxMulticastPkts" },
+	{ 4, 0x18, "TxUnicastPkts" },
+	{ 4, 0x1c, "TxCollisions" },
+	{ 4, 0x20, "TxSingleCollision" },
+	{ 4, 0x24, "TxMultipleCollision" },
+	{ 4, 0x28, "TxDeferredTransmit" },
+	{ 4, 0x2c, "TxLateCollision" },
+	{ 4, 0x30, "TxExcessiveCollision" },
+	{ 4, 0x38, "TxPausePkts" },
+	{ 8, 0x3c, "TxQoSOctets" },
+	{ 8, 0x44, "RxOctets" },
+	{ 4, 0x4c, "RxUndersizePkts" },
+	{ 4, 0x50, "RxPausePkts" },
+	{ 4, 0x54, "Pkts64Octets" },
+	{ 4, 0x58, "Pkts65to127Octets" },
+	{ 4, 0x5c, "Pkts128to255Octets" },
+	{ 4, 0x60, "Pkts256to511Octets" },
+	{ 4, 0x64, "Pkts512to1023Octets" },
+	{ 4, 0x68, "Pkts1024to1522Octets" },
+	{ 4, 0x6c, "RxOversizePkts" },
+	{ 4, 0x70, "RxJabbers" },
+	{ 4, 0x74, "RxAlignmentErrors" },
+	{ 4, 0x78, "RxFCSErrors" },
+	{ 8, 0x7c, "RxGoodOctets" },
+	{ 4, 0x84, "RxDropPkts" },
+	{ 4, 0x88, "RxUnicastPkts" },
+	{ 4, 0x8c, "RxMulticastPkts" },
+	{ 4, 0x90, "RxBroadcastPkts" },
+	{ 4, 0x94, "RxSAChanges" },
+	{ 4, 0x98, "RxFragments" },
+	{ 4, 0xa0, "RxSymbolErrors" },
+	{ 4, 0xa4, "RxQoSPkts" },
+	{ 8, 0xa8, "RxQoSOctets" },
+	{ 4, 0xb0, "Pkts1523to2047Octets" },
+	{ 4, 0xb4, "Pkts2048to4095Octets" },
+	{ 4, 0xb8, "Pkts4096to8191Octets" },
+	{ 4, 0xbc, "Pkts8192to9728Octets" },
+	{ 4, 0xc0, "RxDiscarded" },
+};
+
+#define B53_MIBS_63XX_SIZE	ARRAY_SIZE(b53_mibs_63xx)
+
+/* MIB counters */
+static const struct b53_mib_desc b53_mibs[] = {
+	{ 8, 0x00, "TxOctets" },
+	{ 4, 0x08, "TxDropPkts" },
+	{ 4, 0x10, "TxBroadcastPkts" },
+	{ 4, 0x14, "TxMulticastPkts" },
+	{ 4, 0x18, "TxUnicastPkts" },
+	{ 4, 0x1c, "TxCollisions" },
+	{ 4, 0x20, "TxSingleCollision" },
+	{ 4, 0x24, "TxMultipleCollision" },
+	{ 4, 0x28, "TxDeferredTransmit" },
+	{ 4, 0x2c, "TxLateCollision" },
+	{ 4, 0x30, "TxExcessiveCollision" },
+	{ 4, 0x38, "TxPausePkts" },
+	{ 8, 0x50, "RxOctets" },
+	{ 4, 0x58, "RxUndersizePkts" },
+	{ 4, 0x5c, "RxPausePkts" },
+	{ 4, 0x60, "Pkts64Octets" },
+	{ 4, 0x64, "Pkts65to127Octets" },
+	{ 4, 0x68, "Pkts128to255Octets" },
+	{ 4, 0x6c, "Pkts256to511Octets" },
+	{ 4, 0x70, "Pkts512to1023Octets" },
+	{ 4, 0x74, "Pkts1024to1522Octets" },
+	{ 4, 0x78, "RxOversizePkts" },
+	{ 4, 0x7c, "RxJabbers" },
+	{ 4, 0x80, "RxAlignmentErrors" },
+	{ 4, 0x84, "RxFCSErrors" },
+	{ 8, 0x88, "RxGoodOctets" },
+	{ 4, 0x90, "RxDropPkts" },
+	{ 4, 0x94, "RxUnicastPkts" },
+	{ 4, 0x98, "RxMulticastPkts" },
+	{ 4, 0x9c, "RxBroadcastPkts" },
+	{ 4, 0xa0, "RxSAChanges" },
+	{ 4, 0xa4, "RxFragments" },
+	{ 4, 0xa8, "RxJumboPkts" },
+	{ 4, 0xac, "RxSymbolErrors" },
+	{ 4, 0xc0, "RxDiscarded" },
+};
+
+#define B53_MIBS_SIZE	ARRAY_SIZE(b53_mibs)
+
+static int b53_do_vlan_op(struct b53_device *dev, u8 op)
+{
+	unsigned int i;
+
+	b53_write8(dev, B53_ARLIO_PAGE, dev->vta_regs[0], VTA_START_CMD | op);
+
+	for (i = 0; i < 10; i++) {
+		u8 vta;
+
+		b53_read8(dev, B53_ARLIO_PAGE, dev->vta_regs[0], &vta);
+		if (!(vta & VTA_START_CMD))
+			return 0;
+
+		usleep_range(100, 200);
+	}
+
+	return -EIO;
+}
+
+static void b53_set_vlan_entry(struct b53_device *dev, u16 vid, u16 members,
+			       u16 untag)
+{
+	if (is5325(dev)) {
+		u32 entry = 0;
+
+		if (members) {
+			entry = ((untag & VA_UNTAG_MASK_25) << VA_UNTAG_S_25) |
+				members;
+			if (dev->core_rev >= 3)
+				entry |= VA_VALID_25_R4 | vid << VA_VID_HIGH_S;
+			else
+				entry |= VA_VALID_25;
+		}
+
+		b53_write32(dev, B53_VLAN_PAGE, B53_VLAN_WRITE_25, entry);
+		b53_write16(dev, B53_VLAN_PAGE, B53_VLAN_TABLE_ACCESS_25, vid |
+			    VTA_RW_STATE_WR | VTA_RW_OP_EN);
+	} else if (is5365(dev)) {
+		u16 entry = 0;
+
+		if (members)
+			entry = ((untag & VA_UNTAG_MASK_65) << VA_UNTAG_S_65) |
+				members | VA_VALID_65;
+
+		b53_write16(dev, B53_VLAN_PAGE, B53_VLAN_WRITE_65, entry);
+		b53_write16(dev, B53_VLAN_PAGE, B53_VLAN_TABLE_ACCESS_65, vid |
+			    VTA_RW_STATE_WR | VTA_RW_OP_EN);
+	} else {
+		b53_write16(dev, B53_ARLIO_PAGE, dev->vta_regs[1], vid);
+		b53_write32(dev, B53_ARLIO_PAGE, dev->vta_regs[2],
+			    (untag << VTE_UNTAG_S) | members);
+
+		b53_do_vlan_op(dev, VTA_CMD_WRITE);
+	}
+}
+
+void b53_set_forwarding(struct b53_device *dev, int enable)
+{
+	u8 mgmt;
+
+	b53_read8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, &mgmt);
+
+	if (enable)
+		mgmt |= SM_SW_FWD_EN;
+	else
+		mgmt &= ~SM_SW_FWD_EN;
+
+	b53_write8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, mgmt);
+}
+
+static void b53_enable_vlan(struct b53_device *dev, int enable)
+{
+	u8 mgmt, vc0, vc1, vc4 = 0, vc5;
+
+	b53_read8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, &mgmt);
+	b53_read8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL0, &vc0);
+	b53_read8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL1, &vc1);
+
+	if (is5325(dev) || is5365(dev)) {
+		b53_read8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL4_25, &vc4);
+		b53_read8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL5_25, &vc5);
+	} else if (is63xx(dev)) {
+		b53_read8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL4_63XX, &vc4);
+		b53_read8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL5_63XX, &vc5);
+	} else {
+		b53_read8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL4, &vc4);
+		b53_read8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL5, &vc5);
+	}
+
+	mgmt &= ~SM_SW_FWD_MODE;
+
+	if (enable) {
+		vc0 |= VC0_VLAN_EN | VC0_VID_CHK_EN | VC0_VID_HASH_VID;
+		vc1 |= VC1_RX_MCST_UNTAG_EN | VC1_RX_MCST_FWD_EN;
+		vc4 &= ~VC4_ING_VID_CHECK_MASK;
+		vc4 |= VC4_ING_VID_VIO_DROP << VC4_ING_VID_CHECK_S;
+		vc5 |= VC5_DROP_VTABLE_MISS;
+
+		if (is5325(dev))
+			vc0 &= ~VC0_RESERVED_1;
+
+		if (is5325(dev) || is5365(dev))
+			vc1 |= VC1_RX_MCST_TAG_EN;
+
+		if (!is5325(dev) && !is5365(dev)) {
+			if (dev->allow_vid_4095)
+				vc5 |= VC5_VID_FFF_EN;
+			else
+				vc5 &= ~VC5_VID_FFF_EN;
+		}
+	} else {
+		vc0 &= ~(VC0_VLAN_EN | VC0_VID_CHK_EN | VC0_VID_HASH_VID);
+		vc1 &= ~(VC1_RX_MCST_UNTAG_EN | VC1_RX_MCST_FWD_EN);
+		vc4 &= ~VC4_ING_VID_CHECK_MASK;
+		vc5 &= ~VC5_DROP_VTABLE_MISS;
+
+		if (is5325(dev) || is5365(dev))
+			vc4 |= VC4_ING_VID_VIO_FWD << VC4_ING_VID_CHECK_S;
+		else
+			vc4 |= VC4_ING_VID_VIO_TO_IMP << VC4_ING_VID_CHECK_S;
+
+		if (is5325(dev) || is5365(dev))
+			vc1 &= ~VC1_RX_MCST_TAG_EN;
+
+		if (!is5325(dev) && !is5365(dev))
+			vc5 &= ~VC5_VID_FFF_EN;
+	}
+
+	b53_write8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL0, vc0);
+	b53_write8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL1, vc1);
+
+	if (is5325(dev) || is5365(dev)) {
+		/* enable the high 8 bit vid check on 5325 */
+		if (is5325(dev) && enable)
+			b53_write8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL3,
+				   VC3_HIGH_8BIT_EN);
+		else
+			b53_write8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL3, 0);
+
+		b53_write8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL4_25, vc4);
+		b53_write8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL5_25, vc5);
+	} else if (is63xx(dev)) {
+		b53_write16(dev, B53_VLAN_PAGE, B53_VLAN_CTRL3_63XX, 0);
+		b53_write8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL4_63XX, vc4);
+		b53_write8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL5_63XX, vc5);
+	} else {
+		b53_write16(dev, B53_VLAN_PAGE, B53_VLAN_CTRL3, 0);
+		b53_write8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL4, vc4);
+		b53_write8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL5, vc5);
+	}
+
+	b53_write8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, mgmt);
+}
+
+static int b53_set_jumbo(struct b53_device *dev, bool enable, bool allow_10_100)
+{
+	u32 port_mask = 0;
+	u16 max_size = JMS_MIN_SIZE;
+
+	if (is5325(dev) || is5365(dev))
+		return -EINVAL;
+
+	if (enable) {
+		port_mask = dev->enabled_ports;
+		max_size = JMS_MAX_SIZE;
+		if (allow_10_100)
+			port_mask |= JPM_10_100_JUMBO_EN;
+	}
+
+	b53_write32(dev, B53_JUMBO_PAGE, dev->jumbo_pm_reg, port_mask);
+	return b53_write16(dev, B53_JUMBO_PAGE, dev->jumbo_size_reg, max_size);
+}
+
+static int b53_flush_arl(struct b53_device *dev)
+{
+	unsigned int i;
+
+	b53_write8(dev, B53_CTRL_PAGE, B53_FAST_AGE_CTRL,
+		   FAST_AGE_DONE | FAST_AGE_DYNAMIC | FAST_AGE_STATIC);
+
+	for (i = 0; i < 10; i++) {
+		u8 fast_age_ctrl;
+
+		b53_read8(dev, B53_CTRL_PAGE, B53_FAST_AGE_CTRL,
+			  &fast_age_ctrl);
+
+		if (!(fast_age_ctrl & FAST_AGE_DONE))
+			goto out;
+
+		msleep(1);
+	}
+
+	return -ETIMEDOUT;
+out:
+	/* Only age dynamic entries (default behavior) */
+	b53_write8(dev, B53_CTRL_PAGE, B53_FAST_AGE_CTRL, FAST_AGE_DYNAMIC);
+	return 0;
+}
+
+static int b53_enable_port(struct dsa_switch *ds, int port,
+			   struct phy_device *phy)
+{
+	struct b53_device *dev = ds_to_priv(ds);
+
+	/* Clear the Rx and Tx disable bits and set to no spanning tree */
+	b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(port), 0);
+
+	return 0;
+}
+
+static void b53_disable_port(struct dsa_switch *ds, int port,
+			     struct phy_device *phy)
+{
+	struct b53_device *dev = ds_to_priv(ds);
+	u8 reg;
+
+	/* Disable Tx/Rx for the port */
+	b53_read8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(port), &reg);
+	reg |= PORT_CTRL_RX_DISABLE | PORT_CTRL_TX_DISABLE;
+	b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(port), reg);
+}
+
+static void b53_enable_cpu_port(struct b53_device *dev)
+{
+	unsigned int cpu_port = dev->cpu_port;
+	u8 port_ctrl;
+
+	/* BCM5325 CPU port is at 8 */
+	if ((is5325(dev) || is5365(dev)) && cpu_port == B53_CPU_PORT_25)
+		cpu_port = B53_CPU_PORT;
+
+	port_ctrl = PORT_CTRL_RX_BCST_EN |
+		    PORT_CTRL_RX_MCST_EN |
+		    PORT_CTRL_RX_UCST_EN;
+	b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(cpu_port), port_ctrl);
+}
+
+static void b53_enable_mib(struct b53_device *dev)
+{
+	u8 gc;
+
+	b53_read8(dev, B53_MGMT_PAGE, B53_GLOBAL_CONFIG, &gc);
+	gc &= ~(GC_RESET_MIB | GC_MIB_AC_EN);
+	b53_write8(dev, B53_MGMT_PAGE, B53_GLOBAL_CONFIG, gc);
+}
+
+static int b53_configure_vlan(struct b53_device *dev)
+{
+	int i;
+
+	/* clear all vlan entries */
+	if (is5325(dev) || is5365(dev)) {
+		for (i = 1; i < dev->num_vlans; i++)
+			b53_set_vlan_entry(dev, i, 0, 0);
+	} else {
+		b53_do_vlan_op(dev, VTA_CMD_CLEAR);
+	}
+
+	b53_enable_vlan(dev, false);
+
+	b53_for_each_port(dev, i)
+		b53_write16(dev, B53_VLAN_PAGE,
+			    B53_VLAN_PORT_DEF_TAG(i), 1);
+
+	if (!is5325(dev) && !is5365(dev))
+		b53_set_jumbo(dev, dev->enable_jumbo, false);
+
+	return 0;
+}
+
+static void b53_switch_reset_gpio(struct b53_device *dev)
+{
+	int gpio = dev->reset_gpio;
+
+	if (gpio < 0)
+		return;
+
+	/* Reset sequence: RESET low(50ms)->high(20ms)
+	 */
+	gpio_set_value(gpio, 0);
+	mdelay(50);
+
+	gpio_set_value(gpio, 1);
+	mdelay(20);
+
+	dev->current_page = 0xff;
+}
+
+static int b53_switch_reset(struct b53_device *dev)
+{
+	u8 mgmt;
+
+	b53_switch_reset_gpio(dev);
+
+	if (is539x(dev)) {
+		b53_write8(dev, B53_CTRL_PAGE, B53_SOFTRESET, 0x83);
+		b53_write8(dev, B53_CTRL_PAGE, B53_SOFTRESET, 0x00);
+	}
+
+	b53_read8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, &mgmt);
+
+	if (!(mgmt & SM_SW_FWD_EN)) {
+		mgmt &= ~SM_SW_FWD_MODE;
+		mgmt |= SM_SW_FWD_EN;
+
+		b53_write8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, mgmt);
+		b53_read8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, &mgmt);
+
+		if (!(mgmt & SM_SW_FWD_EN)) {
+			dev_err(dev->dev, "Failed to enable switch!\n");
+			return -EINVAL;
+		}
+	}
+
+	b53_enable_mib(dev);
+
+	return b53_flush_arl(dev);
+}
+
+static int b53_phy_read16(struct dsa_switch *ds, int addr, int reg)
+{
+	struct b53_device *priv = ds_to_priv(ds);
+	u16 value = 0;
+	int ret;
+
+	if (priv->ops->phy_read16)
+		ret = priv->ops->phy_read16(priv, addr, reg, &value);
+	else
+		ret = b53_read16(priv, B53_PORT_MII_PAGE(addr),
+				 reg * 2, &value);
+
+	return ret ? ret : value;
+}
+
+static int b53_phy_write16(struct dsa_switch *ds, int addr, int reg, u16 val)
+{
+	struct b53_device *priv = ds_to_priv(ds);
+
+	if (priv->ops->phy_write16)
+		return priv->ops->phy_write16(priv, addr, reg, val);
+
+	return b53_write16(priv, B53_PORT_MII_PAGE(addr), reg * 2, val);
+}
+
+static int b53_reset_switch(struct b53_device *priv)
+{
+	/* reset vlans */
+	priv->enable_jumbo = false;
+
+	memset(priv->ports, 0, sizeof(*priv->ports) * priv->num_ports);
+
+	return b53_switch_reset(priv);
+}
+
+static int b53_apply_config(struct b53_device *priv)
+{
+	/* disable switching */
+	b53_set_forwarding(priv, 0);
+
+	b53_configure_vlan(priv);
+
+	/* enable switching */
+	b53_set_forwarding(priv, 1);
+
+	return 0;
+}
+
+static void b53_reset_mib(struct b53_device *priv)
+{
+	u8 gc;
+
+	b53_read8(priv, B53_MGMT_PAGE, B53_GLOBAL_CONFIG, &gc);
+
+	b53_write8(priv, B53_MGMT_PAGE, B53_GLOBAL_CONFIG, gc | GC_RESET_MIB);
+	msleep(1);
+	b53_write8(priv, B53_MGMT_PAGE, B53_GLOBAL_CONFIG, gc & ~GC_RESET_MIB);
+	msleep(1);
+}
+
+static const struct b53_mib_desc *b53_get_mib(struct b53_device *dev)
+{
+	if (is5365(dev))
+		return b53_mibs_65;
+	else if (is63xx(dev))
+		return b53_mibs_63xx;
+	else
+		return b53_mibs;
+}
+
+static unsigned int b53_get_mib_size(struct b53_device *dev)
+{
+	if (is5365(dev))
+		return B53_MIBS_65_SIZE;
+	else if (is63xx(dev))
+		return B53_MIBS_63XX_SIZE;
+	else
+		return B53_MIBS_SIZE;
+}
+
+static void b53_get_strings(struct dsa_switch *ds, int port, uint8_t *data)
+{
+	struct b53_device *dev = ds_to_priv(ds);
+	const struct b53_mib_desc *mibs = b53_get_mib(dev);
+	unsigned int mib_size = b53_get_mib_size(dev);
+	unsigned int i;
+
+	for (i = 0; i < mib_size; i++)
+		memcpy(data + i * ETH_GSTRING_LEN,
+		       mibs[i].name, ETH_GSTRING_LEN);
+}
+
+static void b53_get_ethtool_stats(struct dsa_switch *ds, int port,
+				  uint64_t *data)
+{
+	struct b53_device *dev = ds_to_priv(ds);
+	const struct b53_mib_desc *mibs = b53_get_mib(dev);
+	unsigned int mib_size = b53_get_mib_size(dev);
+	const struct b53_mib_desc *s;
+	unsigned int i;
+	u64 val = 0;
+
+	if (is5365(dev) && port == 5)
+		port = 8;
+
+	mutex_lock(&dev->stats_mutex);
+
+	for (i = 0; i < mib_size; i++) {
+		s = &mibs[i];
+
+		if (mibs->size == 8) {
+			b53_read64(dev, B53_MIB_PAGE(port), s->offset, &val);
+		} else {
+			u32 val32;
+
+			b53_read32(dev, B53_MIB_PAGE(port), s->offset,
+				   &val32);
+			val = val32;
+		}
+		data[i] = (u64)val;
+	}
+
+	mutex_unlock(&dev->stats_mutex);
+}
+
+static int b53_get_sset_count(struct dsa_switch *ds)
+{
+	struct b53_device *dev = ds_to_priv(ds);
+
+	return b53_get_mib_size(dev);
+}
+
+static int b53_set_addr(struct dsa_switch *ds, u8 *addr)
+{
+	return 0;
+}
+
+static int b53_setup(struct dsa_switch *ds)
+{
+	struct b53_device *dev = ds_to_priv(ds);
+	unsigned int port;
+	int ret;
+
+	ret = b53_reset_switch(dev);
+	if (ret) {
+		dev_err(ds->dev, "failed to reset switch\n");
+		return ret;
+	}
+
+	b53_reset_mib(dev);
+
+	ret = b53_apply_config(dev);
+	if (ret)
+		dev_err(ds->dev, "failed to apply configuration\n");
+
+	for (port = 0; port < dev->num_ports; port++) {
+		if (BIT(port) & ds->enabled_port_mask)
+			b53_enable_port(ds, port, NULL);
+		else if (dsa_is_cpu_port(ds, port))
+			b53_enable_cpu_port(dev);
+		else
+			b53_disable_port(ds, port, NULL);
+	}
+
+	return ret;
+}
+
+static void b53_adjust_link(struct dsa_switch *ds, int port,
+			    struct phy_device *phydev)
+{
+	struct b53_device *dev = ds_to_priv(ds);
+	u8 rgmii_ctrl = 0, reg = 0, off;
+
+	if (!phy_is_pseudo_fixed_link(phydev))
+		return;
+
+	/* Override the port settings */
+	if (port == dev->cpu_port) {
+		off = B53_PORT_OVERRIDE_CTRL;
+		reg = PORT_OVERRIDE_EN;
+	} else {
+		off = B53_GMII_PORT_OVERRIDE_CTRL(port);
+		reg = GMII_PO_EN;
+	}
+
+	/* Set the link UP */
+	if (phydev->link)
+		reg |= PORT_OVERRIDE_LINK;
+
+	if (phydev->duplex == DUPLEX_FULL)
+		reg |= PORT_OVERRIDE_FULL_DUPLEX;
+
+	switch (phydev->speed) {
+	case 2000:
+		reg |= PORT_OVERRIDE_SPEED_2000M;
+		/* fallthrough */
+	case SPEED_1000:
+		reg |= PORT_OVERRIDE_SPEED_1000M;
+		break;
+	case SPEED_100:
+		reg |= PORT_OVERRIDE_SPEED_100M;
+		break;
+	case SPEED_10:
+		reg |= PORT_OVERRIDE_SPEED_10M;
+		break;
+	default:
+		dev_err(ds->dev, "unknown speed: %d\n", phydev->speed);
+		return;
+	}
+
+	/* Enable flow control on BCM5301x's CPU port */
+	if (is5301x(dev) && port == dev->cpu_port)
+		reg |= PORT_OVERRIDE_RX_FLOW | PORT_OVERRIDE_TX_FLOW;
+
+	if (phydev->pause) {
+		if (phydev->asym_pause)
+			reg |= PORT_OVERRIDE_TX_FLOW;
+		reg |= PORT_OVERRIDE_RX_FLOW;
+	}
+
+	b53_write8(dev, B53_CTRL_PAGE, off, reg);
+
+	if (is531x5(dev) && phy_interface_is_rgmii(phydev)) {
+		if (port == 8)
+			off = B53_RGMII_CTRL_IMP;
+		else
+			off = B53_RGMII_CTRL_P(port);
+
+		/* Configure the port RGMII clock delay by DLL disabled and
+		 * tx_clk aligned timing (restoring to reset defaults)
+		 */
+		b53_read8(dev, B53_CTRL_PAGE, off, &rgmii_ctrl);
+		rgmii_ctrl &= ~(RGMII_CTRL_DLL_RXC | RGMII_CTRL_DLL_TXC |
+				RGMII_CTRL_TIMING_SEL);
+
+		/* PHY_INTERFACE_MODE_RGMII_TXID means TX internal delay, make
+		 * sure that we enable the port TX clock internal delay to
+		 * account for this internal delay that is inserted, otherwise
+		 * the switch won't be able to receive correctly.
+		 *
+		 * PHY_INTERFACE_MODE_RGMII means that we are not introducing
+		 * any delay neither on transmission nor reception, so the
+		 * BCM53125 must also be configured accordingly to account for
+		 * the lack of delay and introduce
+		 *
+		 * The BCM53125 switch has its RX clock and TX clock control
+		 * swapped, hence the reason why we modify the TX clock path in
+		 * the "RGMII" case
+		 */
+		if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
+			rgmii_ctrl |= RGMII_CTRL_DLL_TXC;
+		if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
+			rgmii_ctrl |= RGMII_CTRL_DLL_TXC | RGMII_CTRL_DLL_RXC;
+		rgmii_ctrl |= RGMII_CTRL_TIMING_SEL;
+		b53_write8(dev, B53_CTRL_PAGE, off, rgmii_ctrl);
+
+		dev_info(ds->dev, "Configured port %d for %s\n", port,
+			 phy_modes(phydev->interface));
+	}
+
+	/* configure MII port if necessary */
+	if (is5325(dev)) {
+		b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL,
+			  &reg);
+
+		/* reverse mii needs to be enabled */
+		if (!(reg & PORT_OVERRIDE_RV_MII_25)) {
+			b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL,
+				   reg | PORT_OVERRIDE_RV_MII_25);
+			b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL,
+				  &reg);
+
+			if (!(reg & PORT_OVERRIDE_RV_MII_25)) {
+				dev_err(ds->dev,
+					"Failed to enable reverse MII mode\n");
+				return;
+			}
+		}
+	} else if (is5301x(dev)) {
+		if (port != dev->cpu_port) {
+			u8 po_reg = B53_GMII_PORT_OVERRIDE_CTRL(dev->cpu_port);
+			u8 gmii_po;
+
+			b53_read8(dev, B53_CTRL_PAGE, po_reg, &gmii_po);
+			gmii_po |= GMII_PO_LINK |
+				   GMII_PO_RX_FLOW |
+				   GMII_PO_TX_FLOW |
+				   GMII_PO_EN |
+				   GMII_PO_SPEED_2000M;
+			b53_write8(dev, B53_CTRL_PAGE, po_reg, gmii_po);
+		}
+	}
+}
+
+static struct dsa_switch_driver b53_switch_ops = {
+	.tag_protocol		= DSA_TAG_PROTO_NONE,
+	.setup			= b53_setup,
+	.set_addr		= b53_set_addr,
+	.get_strings		= b53_get_strings,
+	.get_ethtool_stats	= b53_get_ethtool_stats,
+	.get_sset_count		= b53_get_sset_count,
+	.phy_read		= b53_phy_read16,
+	.phy_write		= b53_phy_write16,
+	.adjust_link		= b53_adjust_link,
+	.port_enable		= b53_enable_port,
+	.port_disable		= b53_disable_port,
+};
+
+struct b53_chip_data {
+	u32 chip_id;
+	const char *dev_name;
+	u16 vlans;
+	u16 enabled_ports;
+	u8 cpu_port;
+	u8 vta_regs[3];
+	u8 duplex_reg;
+	u8 jumbo_pm_reg;
+	u8 jumbo_size_reg;
+};
+
+#define B53_VTA_REGS	\
+	{ B53_VT_ACCESS, B53_VT_INDEX, B53_VT_ENTRY }
+#define B53_VTA_REGS_9798 \
+	{ B53_VT_ACCESS_9798, B53_VT_INDEX_9798, B53_VT_ENTRY_9798 }
+#define B53_VTA_REGS_63XX \
+	{ B53_VT_ACCESS_63XX, B53_VT_INDEX_63XX, B53_VT_ENTRY_63XX }
+
+static const struct b53_chip_data b53_switch_chips[] = {
+	{
+		.chip_id = BCM5325_DEVICE_ID,
+		.dev_name = "BCM5325",
+		.vlans = 16,
+		.enabled_ports = 0x1f,
+		.cpu_port = B53_CPU_PORT_25,
+		.duplex_reg = B53_DUPLEX_STAT_FE,
+	},
+	{
+		.chip_id = BCM5365_DEVICE_ID,
+		.dev_name = "BCM5365",
+		.vlans = 256,
+		.enabled_ports = 0x1f,
+		.cpu_port = B53_CPU_PORT_25,
+		.duplex_reg = B53_DUPLEX_STAT_FE,
+	},
+	{
+		.chip_id = BCM5395_DEVICE_ID,
+		.dev_name = "BCM5395",
+		.vlans = 4096,
+		.enabled_ports = 0x1f,
+		.cpu_port = B53_CPU_PORT,
+		.vta_regs = B53_VTA_REGS,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+	{
+		.chip_id = BCM5397_DEVICE_ID,
+		.dev_name = "BCM5397",
+		.vlans = 4096,
+		.enabled_ports = 0x1f,
+		.cpu_port = B53_CPU_PORT,
+		.vta_regs = B53_VTA_REGS_9798,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+	{
+		.chip_id = BCM5398_DEVICE_ID,
+		.dev_name = "BCM5398",
+		.vlans = 4096,
+		.enabled_ports = 0x7f,
+		.cpu_port = B53_CPU_PORT,
+		.vta_regs = B53_VTA_REGS_9798,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+	{
+		.chip_id = BCM53115_DEVICE_ID,
+		.dev_name = "BCM53115",
+		.vlans = 4096,
+		.enabled_ports = 0x1f,
+		.vta_regs = B53_VTA_REGS,
+		.cpu_port = B53_CPU_PORT,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+	{
+		.chip_id = BCM53125_DEVICE_ID,
+		.dev_name = "BCM53125",
+		.vlans = 4096,
+		.enabled_ports = 0xff,
+		.cpu_port = B53_CPU_PORT,
+		.vta_regs = B53_VTA_REGS,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+	{
+		.chip_id = BCM53128_DEVICE_ID,
+		.dev_name = "BCM53128",
+		.vlans = 4096,
+		.enabled_ports = 0x1ff,
+		.cpu_port = B53_CPU_PORT,
+		.vta_regs = B53_VTA_REGS,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+	{
+		.chip_id = BCM63XX_DEVICE_ID,
+		.dev_name = "BCM63xx",
+		.vlans = 4096,
+		.enabled_ports = 0, /* pdata must provide them */
+		.cpu_port = B53_CPU_PORT,
+		.vta_regs = B53_VTA_REGS_63XX,
+		.duplex_reg = B53_DUPLEX_STAT_63XX,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK_63XX,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE_63XX,
+	},
+	{
+		.chip_id = BCM53010_DEVICE_ID,
+		.dev_name = "BCM53010",
+		.vlans = 4096,
+		.enabled_ports = 0x1f,
+		.cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */
+		.vta_regs = B53_VTA_REGS,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+	{
+		.chip_id = BCM53011_DEVICE_ID,
+		.dev_name = "BCM53011",
+		.vlans = 4096,
+		.enabled_ports = 0x1bf,
+		.cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */
+		.vta_regs = B53_VTA_REGS,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+	{
+		.chip_id = BCM53012_DEVICE_ID,
+		.dev_name = "BCM53012",
+		.vlans = 4096,
+		.enabled_ports = 0x1bf,
+		.cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */
+		.vta_regs = B53_VTA_REGS,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+	{
+		.chip_id = BCM53018_DEVICE_ID,
+		.dev_name = "BCM53018",
+		.vlans = 4096,
+		.enabled_ports = 0x1f,
+		.cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */
+		.vta_regs = B53_VTA_REGS,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+	{
+		.chip_id = BCM53019_DEVICE_ID,
+		.dev_name = "BCM53019",
+		.vlans = 4096,
+		.enabled_ports = 0x1f,
+		.cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */
+		.vta_regs = B53_VTA_REGS,
+		.duplex_reg = B53_DUPLEX_STAT_GE,
+		.jumbo_pm_reg = B53_JUMBO_PORT_MASK,
+		.jumbo_size_reg = B53_JUMBO_MAX_SIZE,
+	},
+};
+
+static int b53_switch_init(struct b53_device *dev)
+{
+	struct dsa_switch *ds = dev->ds;
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < ARRAY_SIZE(b53_switch_chips); i++) {
+		const struct b53_chip_data *chip = &b53_switch_chips[i];
+
+		if (chip->chip_id == dev->chip_id) {
+			if (!dev->enabled_ports)
+				dev->enabled_ports = chip->enabled_ports;
+			dev->name = chip->dev_name;
+			dev->duplex_reg = chip->duplex_reg;
+			dev->vta_regs[0] = chip->vta_regs[0];
+			dev->vta_regs[1] = chip->vta_regs[1];
+			dev->vta_regs[2] = chip->vta_regs[2];
+			dev->jumbo_pm_reg = chip->jumbo_pm_reg;
+			ds->drv = &b53_switch_ops;
+			dev->cpu_port = chip->cpu_port;
+			dev->num_vlans = chip->vlans;
+			break;
+		}
+	}
+
+	/* check which BCM5325x version we have */
+	if (is5325(dev)) {
+		u8 vc4;
+
+		b53_read8(dev, B53_VLAN_PAGE, B53_VLAN_CTRL4_25, &vc4);
+
+		/* check reserved bits */
+		switch (vc4 & 3) {
+		case 1:
+			/* BCM5325E */
+			break;
+		case 3:
+			/* BCM5325F - do not use port 4 */
+			dev->enabled_ports &= ~BIT(4);
+			break;
+		default:
+/* On the BCM47XX SoCs this is the supported internal switch.*/
+#ifndef CONFIG_BCM47XX
+			/* BCM5325M */
+			return -EINVAL;
+#else
+			break;
+#endif
+		}
+	} else if (dev->chip_id == BCM53115_DEVICE_ID) {
+		u64 strap_value;
+
+		b53_read48(dev, B53_STAT_PAGE, B53_STRAP_VALUE, &strap_value);
+		/* use second IMP port if GMII is enabled */
+		if (strap_value & SV_GMII_CTRL_115)
+			dev->cpu_port = 5;
+	}
+
+	/* cpu port is always last */
+	dev->num_ports = dev->cpu_port + 1;
+	dev->enabled_ports |= BIT(dev->cpu_port);
+
+	dev->ports = devm_kzalloc(dev->dev,
+				  sizeof(struct b53_port) * dev->num_ports,